easyRAID S8A2-PETT Hardware User Manual PCIe to Serial ATA II
Contents
1. 200000000 o 90000000 y Item Specification Host Interface PCle Disk Interface SATA II 3 0 Gb s Dimensions 336 mm H x 200 mm W x 321 mm D RAID Functions Raid levels JBOD 0 0 1 5 6 Hot spare support Disk hot swapping with automatic online rebuilding Multiple RAID max 8 Disk Array Func tions Up to 1GB DDR SDRAM LCD panel operation indicator Audible alarm disable alarm LED indicator on disk failures Connectors PCle port RS 232 Serial port 115200 8 N 1 Redundant 300 Watt 100 240 VAC 47 63 Hz 6 3A 10 Over voltage current power and short circuit protection LED indicates power status Operating temperature 5 C 40 C Operating humidity 10 85 non condensing Output 5V 3 3V 12V Power Supply Warranty 3 year warranty Safety UL CE and FCC Class B 212. these instructions to upgrade the memory 1 Remove the screws from the disk array system and pull the controller box 2 Retaining away the DIMM springs out of the socket Remove the DIMM 3 Gently push the new DIMM into the socket then push the corners of the DIMM down The DIMM is secured by the DIMM retaining clips 16 easyRAID S8A2 PETT Serial ATA II Disk Array Systems Please the top cover on the disk array system and replace the screws to fix the cover oooooooo O 060000000 Note LK The DIMM module will fit in only one direction Do not force the DIMM into place Aowa Bu pei dn soueusjureyy e ajnpow NY e Buejday soueusjuiey easyRAID S8A2 PETT Serial ATA II Disk Array Systems When one of the FAN module fails the massage FANx Fail appears on the LCD panel where x refers to power supply 1 or 2 and an audible alert sounds Note Turn off the audible alert by pressing the Up and Down function buttons on the front panel twice simultaneously 1 Identify the FAN module that has failed loosen the retaining screws slide it out of chassis See A and B 18 easyRAID S8A2 PETT Serial ATA II Disk Array Systems Insert a new FAN module tighten retaining screws See C and D 2
3. 2 System cooling fan Power Supply 1 Removable redundant power supply 1 Power Supply Handle For power supply removal Power Supply AC In Connects to a 100 240 VAC power source Power Supply 2 Removable redundant power supply 2 Power Supply Handle For power supply removal O COIN O O A oa N Power Supply AC In Connects to a 100 240 VAC power source o Power Switch Switches the power on or off _ RS 232 Port Connects to a VT100 terminal or equivalent easyRAID S8A2 PETT Serial ATA II Disk Array Systems This section describes how to install disks in the disk array system 1 Unlock the fan then pull it open 2 Push the button to release the disk tray handle 3 Pull the handle to release the tray sysiq Buljjeysuj uonenmbBuo seg Z easyRAID S8A2 PETT Serial ATA II Disk Array Systems Insert the disk into the disk tray and fix into place with screws supplied with the disk 4 Insert the disk tray back into the empty slot 5 6 Repeat steps 2 to 5 until all of the required disk have been installed 7 Push the fan closed and lock it easyRAID S8A2 PETT Serial ATA II Disk Array Systems After the required number of disks have been installed external connections to the disk array system must be made This secti
4. 3 wire grounded plug The third pin connects to ground do not remove it If the power cord or plug is damaged or worn unplug it immediately and contact a qualified service technician for maintenance To avoid fire or electric shocks do not overload electric power out lets CAUTION MULTIPLE POWER SOURCES Disconnect all AC power cords to completely power from the unit gt CAUTION Risk of explosion if battery is replaced by an incorrect type Dispose of used batteries according to the instructions gt CAUTION The thumbscrews on the rear surface shall be secured by the screw driver which cannot be loosened by bare hands to prevent the uninten tional access to the hazardous parts inside the equipment gt 1 System Requirements Ensure that the following requirements are met before installing the disk array system 15 cm 6 inches of space around the disk array system for proper ventilation e ambient temperature of 5 C to 40 C 40 F to 104 F ambient non condensing relative humidity of 10 to 85 e dust smoke and oil free environment no large magnetic fields such as those generated by a high voltage power cables and motors etc e no direct sunlight a flat stable surface capable of supporting the disk array system VT100 Terminal Settings Refer to the following table for a summary of VT100 terminal settings required to com municate with the disk array system Refer to your system ma
5. HOU C29 eg o O 980 028880 09898988826 52596250596 9050505050 2938898898958 29280828289 O 99998282888 o SLSLGLGLQGQG_ rm 2993990899890 3883888 8 O O Q 8886 288 0928882880 60508980808 33333333338 6850525089 32399089888 o 2929992898 O 28988598982 e 039832999985 039893 E EN O o OR os P S ly 1 SAH HSH gt ower Supply Power Supply 2 y 2 Remove the power cable from the power supply connector at the rear of the unit Note The system is equipped with auto switching power supplies that can run on 100 to 240 VAC 14 easyRAID S8A2 PETT Serial ATA II Disk Array Systems 3 Loosen the power supply retaining screw 4 Pull the power supply handle out 3 Maintenance Replacing a Power Supply 000000000 o 20000000 Power Supply Ining screw reta 5 Remove the faulty power supply by pulling the power supply handle and press ing the release catch at the same time Insert a new power supply 6 7 Push the power supply handle into place 8 Tighten the power supply thumbscrew 9 Reconnect the power cable 15 Aowa BuipelBdn soueusjureyy easyRAID S8A2 PETT Serial ATA II Disk Array Systems Ungrading Memory The disk array system takes a single DDR 184pin DIMM with a maximum capacity of 1 GB Follow
6. data transfer between the disk array sys tem and the host computer 14 Enter function button Selects a menu item or confirms a choice or entry 15 Down function button Moves down in the LCD menus 16 LCD panel Displays warning operating and configuration information easyRAID S8A2 PETT Serial ATA II Disk Array Systems Disk Tray No Name Description Power Error indicator LED Different colors indicate different disk states e Green Disk online e Orange Disk full e Red No disk 2 Access indicator LED indicates that the disk is being 3 Tray handle Releases the disk tray sjusuodwoy uoneinbyuoy seg Z sjusuodwoy uoneinbyuoy seg Z easyRAID S8A2 PETT Serial ATA II Disk Array Systems easyRAID S8A2 PETT Rear View 11 00000000 000000000 0000000000 20000000000 000000000000 000000000000 00000000000 00000000 000000000 0000000000 200000000000 O 200000000000 O O O 0000000000000 0000000000000 Q 000000000000 00000000000 0000000000 000000000 00000000 10 z o Name Description Host Port 1 PCle channel Connects to the host server Cooling fan 1 System cooling fan Cooling fan
7. easyRAID S8A2 PETT Hardware User Manual PCle to Serial ATA Il Disk Array System Version 1 0 easyRAID S8A2 PETT PCIe to Serial ATA Il Disk Array System Hardware User Manual Table of Contents Preface ete ested 6 Chapter 1 System Requirements Operating Environment 22 ccceeseeeeceeeeeeeeeeeseeneeeeeeneeeneeeeees VT100 Terminal Settings a neue ee Chapter 2 Basic Configuration Unpacking ee en Componenis EE EEEE 66 Front Panel caco eena ireia tenn naaar in DISK Tray ende nen ee easyRAID S8A2 PETT Rear View uuueeenssssssennnnennnnnnen nennen Installing Disks san ea Making Connections ar ee catacagertagines Connecting the Host Interface 2 u444 4444444 H0HH RR Connecting PCle cable to the server eccere Connecting and Turning on the Power 22usnsnnnnenne nennen Chapter 3 Maintenance Replacing a Disk cto Replacing a Power Supply cocoooccccccccococonononconono nono nono nono cnn nnnnnnnnnnnnns Upgrading Memory ea lace Replacing a FAN module c ccceecesseececeeeeeeeeedeeeteeeeeeeeeneseees Hardware Specifications This manual is designed to make the disk array system as easy to use as possible Information contained in this document has been checked for accuracy but no guaran tee is given that the contents are correct Information and specifications are subject to change without notice Copyright 2007 All rights re
8. ity than the faulty disk that was removed If the disk capacity is smaller the audible alert sounds and the auto rebuild operation doesn t start For best performance it is recommended that the new disk be identical to the failed disk 6 Attach the disk to the disk tray with the screws that came with the disk 7 Slide the disk tray back into the empty slot then close the disk tray handle 8 Push the front panel door closed and lock it 13 A ddns Jamog e Buloejdey soueusjule easyRAID S8A2 PETT Serial ATA II Disk Array Systems Replacing a Power Supply The disk array system is equipped with a Power Supply Fail Indicator LED at the front of the unit that turns red when one of the power supplies fails The message Power x fail ure also appears on the LCD panel where x refers to power supply 1 or 2 and an audible alert sounds Note Turn off the audible alert by pressing the Up 4 and Down y function but tons on the front panel twice simultaneously Power supplies are hot swappable which means that they can be inserted and removed while the disk array is powered on and operating Follow these instructions to replace a failed power supply 1 Identify the power supply that has failed 5 N OER amp 4 Sy WW i ha S CoN T
9. nual for instructions on setting up the VT100 terminal settings Item Required Setting Connection Serial Port COM1 or COM2 Protocol RS232 Asynchronous Cabling Null Modem cable Baud Rate 115200 Data Bits 8 Stop Bit 1 Parity None 2 Basic Contiguration This chapter describes disk array system connections and disk installation Contact your supplier if any of the following items are missing or damaged Caution A The disk array system is heavy Be careful when lifting and moving it Disk Array System 5 v4 maf fl PCle cable Hardware and software user Manuals J Screw pack sjusuodwoy uoneinbyuo5 oIseg Z easyRAID S8A2 PETT Serial ATA II Disk Array Systems Components easyRAID S8A2 PETT Front Panel o ooo0o0 00000 16 00000000000000 oo o o ooo 0 9 o AOUN o0000000000000 Name Description Disk trays 1 to 8 Removable hot swap disk trays Up function button Moves up in the LCD menus Escape function button changes Returns to the previous LCD menu without making 11 Power on indicator green Indicates the disk array system power is on 12 Power supply fail indicator red Indicates a failed power supply 13 Host computer access indicator Indicates
10. on describes how to make all of the necessary connections The disk array system has PCle interface Refer to the following sections to make host interface connections The easyRAID S8A2 PETT has PCle interface Follow these instructions to make con nections 1 Connect the PCle cable to the left connector of the easyRAID S8A2 PETT host port 1 at the rear of the disk array system o suoloeuUuoy Bulyeyy UOnNeInbBiuoo 91seg Z suoloeuUuoy Bulyeyy Uollein lluog 91seg Z easyRAID S8A2 PETT Serial ATA II Disk Array Systems While the PCle cable has connected to the easyRAID S8A2 PETT the other side of the cable connect to the re drive card A Then install the re drive card A into the PCI slot in the server B 9300000000 J d00000 000000 O c8828223220035 O ji 200000000000 NETT B E A 12 of 2 a Bee u Ps 3 de of P 3 al T m il E re drive card server 10 easyRAID S8A2 PETT Serial ATA II Disk Array Systems Connecting and Turning on the Power 1 Plug a power cable A to a power connector at the rear of the unit then plug the second power supply cable into the second power connector B Note 4 The system is equipped with auto switching powe
11. or venti lation Never block or cover these openings because the disk array system may overheat and become unreli able Don t place the disk array system on a bed sofa rug or other similar surface Do not place the disk array system near or over a radia tor or other heat source Refer to the rating plate for the correct voltage and ensure that the appliance voltage corresponds to the supply voltage easyRAID S8A2 PETT Serial ATA II Disk Array Systems E i The appliance must be grounded The disk array system is equipped with a 3 wire grounded type of power cord This power cord will only fit into a grounded type of power outlet 2 s If an extension cord or a power center is used with the disk array system make sure that the total current con sumption of all products plugged into the wall outlet does not exceed the ampere rating Do not place the disk array system where the cord will be walked on za Never push any kind of object into the disk array system through cabinet gaps and openings since they may touch dangerous voltage points and cause a risk of fire or electric shock iia ya Unplug the power cord from the wall outlet before clean ing Keep the disk array system dry Do not use liquid cleaners aerosol cleaners or a wet cloth Use a damp cloth for cleaning DA Except as specifically explained in this User Manual do not attempt to service the disk a
12. r supplies that can run on 100 to 240 VAC e Please turn on easyRAID S8A2 PETT first then turn on the server which contain the redrive card 2 Switch on power switch C 11 SUOIDSUUOY puien Uollein lluog 91seg Z A disk failure is indicated when the Power Error LED at the front of the drive tray turns red and the audible alert sounds Note 4 Turn off the audible alert by pressing the Up 4 and Down y function but tons on the front panel twice simultaneously The LCD panel displays the failure with the symbol R or W R indicates a disk fail ure or error and W indicates that there are too many bad sectors on the disk Example Disks 1 to 3 are members of array group 1 Disks 4 to 6 are members of array group 2 Disk 7 has too many bad sectors e Disk 8 has an error or a fault 111222WR Disks are hot swappable which means that they can be inserted and removed while the disk array system is powered on and operating Follow these instructions to replace a failed disk 1 Unlock the front panel door then pull it open 2 Pull the tray handle away from the disk tray to release it and pull the disk tray out 3 Remove the screws from the failed disk then remove the disk from the disk tray 4 Align the rear of the new disk with the rear of the disk tray 5 Insert the new disk into the disk tray Note y The new disk must have the same or a greater capac
13. rray system by yourself Opening or removing the covers may expose you to dangerous voltages id Unplug this product from the wall outlet and refer servic ing to qualified service personnel under the following conditions If the disk array system has been exposed to water or any liquid If the disk array system has been dropped or the cabinet damaged Users should not remove the cover Disconnect all power supply cords before servicing BuljpueH pue sued suononssu Ajayes Juenodwj 99BJ3 d BuljpueH pue aed suononssu Ajayes Juenodwj 998J3 d easyRAID S8A2 PETT Serial ATA II Disk Array Systems Placement Notes e The disk array system LCD panel can be damaged by exposure to direct sunlight Limit exposure to subdued or indirect sunlight only e The disk array system should be used only in clean environments that are free from airborne contaminants such as dust dirt and smoke Excessive moisture or oil particles in the air can also hinder disk array system performance To reduce the possibility of data errors caused by electromagnetic interference locate the disk array system at least five feet away from electrical appliances and equipment that generates magnetic fields Power Supply Safety Notes To avoid electric shocks do not use an extended power cord or an outlet that does not match the disk array system plug or leaves the plug exposed e The disk array system has a
14. served This disk array system and related documentation are protected by copyright and are distributed under licenses restricting their use copying and distribu tion No part of this documentation may be reproduced in any form by any means with out prior written authorization and its licensors if any Caution A This symbol is used to remind users to pay attention to important descriptions regarding usage and maintenance repair or additional important information related to this disk array system Note 4 This symbol is used to remind users of useful information that can make procedures such as configuration easier to accomplish BuljpueH pue sued suononssu Ajayes Juenodwj 99BJ3 d easyRAID S8A2 PETT Serial ATA II Disk Array Systems Before starting take a few minutes to read this manual Read all of these instructions and save this manual for later reference Protect the disk array system from extremely high or low temperatures Let the disk array system warm or cool to room temperature before using it Protect the disk array system from being bumped or dropped Do not place the disk array system on an unstable cart stand or table It may fall causing serious damage to the product Keep the disk array system away from magnetic forces Do not use the disk array system near water Keep the disk array system away from dust sand or dirt Gaps and openings in the cabinet are provided f
Download Pdf Manuals
Related Search