Home

USER MANUAL - Mega Systems

image

Contents

1. Connection J 220V Connection i DMX 512 Connection The fixture is equipped with 3 Screw binding post for DMX output Only use a shielded twisted pair cable designed for RS 485 and 3 pin XLR plugs and connectors in order to connect the controller with the fixture Pr GND Shield 1 DMX output e A D Signal 2 E re D Signal 3 00000 Y N Caution At the last fixture the DMX signal needs to be terminated with a terminator Solder a 120 Ohm resistor between the and the signal into a 3 pin XLR plug and plug it in to the last fixture on the signal run Pre manufactured terminator plugs are availa ble for purchase from your Mega Lite dealer P DMXT Main Control Note witch Controller only works on fixtures that are 3 or 4 Channel And that the Channel are as fol lows Channel 1 Red LED Channel 2 Green LED Channel 3 Blue LED Channel 4 White LED And the fixture must be addressed to DMX start Channel 001 Power On Off Tap the screen for power on a blue LED indicator will light showing controller is on Tap the screen for power Off a red LED indicator will light showing the controller is off Single color Control Tap the corresponding circular color for the LED to come on or off Press and hold the corresponding circular color to have the LED dim to the required intensi ty You can mix a to a specific color by having multiple LED color active at the same time
2. USER MANUAL Table of Contents Sarenet 3 SPOE 11 6 one ne nr ae estatico eee ee ae 4 Main Power Connection ccceceee cc eee eee eeeeeeeeeeeeeeaeeeeeaneeeennneenas DMX 512 CoOnnection 0 00 cece ccc eee cece cece eee eceeeeeeeeaneeeeanneeennneeennees 5 Main Control M nu cccccccceecceseceeeeeeeceeeaseecaeeseaeeaseesaeesaeeseeeeeeeeseeeenes Installing the Fixture 2422202220ennennennnnnnnnnnennnnnnennnennnenennnnnene Cleaning amp Maintenance Parts List Check that the unit has not been damaged during transport Read all cautions and warnings prior to operation of this equipment Protection Against Fire Fire Maintain a minimum of 1 foot distance from any type of flame Replace fuse only with the specified type and rating Do Not install the unit to close to a heat source Make sure cable are properly secured away Maximum surface operating temperature 104 D o E goa Protection Against Fire A Electrical Disconnect power before servicing For connection to main power supply proceed to page 5 This unit must be earthed electronically grounded Do not expose unit to rain or moisture a a a Protection Against Mechanical Hazards 1 Use quality gang box when installing unit ak 2 Use quality bolts when positioning unit 3 Do not open unit while it is on risk of electrical shock Mechanical Technical Information Part Numbers Fixture MC 2030
3. Color Wheel Control Tap any where on the circular color wheel to have the color activated Note the white color LED will not be active in the fixture MEGA Dimmer Control Press and hold the dimmer button to dim down the intensity of the fixtures Press and hold again to have the fixtures dim Up Note the white color LED will not be active on the fixture MEGA CTO Control Tap the CTO button to select the White mixed color There is 3 options Note the white color LED will not be active on the fixture Pre Programs Control Tap once to start the preprogram function tap once again to pause the program Tap twice to select the next preprogram There is 10 options Press and Hold to adjust the speed up of the program Press and hold again to adjust the speed down of the program Note the white color LED will not be active on the fixture Record Functions All functions can be recorder to a Record Button S1 S2 S3 including Single Color Control Color Wheel Control Dimmer Control CTO Control and Pre Pro gram Control Select a function you would like to control Press and Hold any of the the S Button for 2 seconds and the program will be recorded To recall the program recorded just Tap the button Note White LED will be recorded to the Playback if selected Installing the fixture Caution 1 The installations must be carried out by an authorized dealer or trained profes sional 2 Unit may cause se
4. Xwitch MEA APV 12 12 Mean Well 12V power Supply included Mechanical Specifications DMX Connectors 3 screw binding strip 42 Power Connections 2 screw binding strip Thermal Maximum ambient temperature 104 Maximum surface temperature 140 Display LED power indicator Mounting System Single gang electrical wall mounting 4 72 2 05 Fixture Packaged for Shipping Size 2 95 L x 1 19 W x 4 72 H Size 9 X 6 5 X 2 75 32 33 Weight 1 lbs Weight 3 Ibs MEGA gt 1 19 Electrical Specifications Power Requirements 12 24VDC 0 2 Amps Touch Sensor Single touch glass sensor e S i A Control amp Programming ce Protocol DMX 512 DMX Channels 4 DMX Channels Operating Mode 3 Programmable static scenes i 10 Built in Preprogram chases with Speed control 2 05 3 Color Temperature presets Dimmer intensity button Power Supply Specifications Model Mean Well APV 12 12 Input Power 100 240VAC 50 60Hz 0 Output Power 12 VDC 1 Amps A Power Connection Bare Cable Mounting System 2 hole screw mounting Main Power Connection Caution 1 Do not connect power supply to a dimmer system 2 This unit has Auto switching power supply It will resoond to 110V or 220V automatically The occupation of the connection cable is as follows This fixture is equipped with an electronic power supply that will let the unit operate from 100V to 240V from 50Hz to N L L 110V
5. gardless of the form of action weather in contract tort including negligence strict liability or otherwise and weather or not such damage was foreseen or unforeseen Warranty is void if the product is misused damaged modified in any way or for unauthorized repairs or parts This warranty gives you specific legal rights and you may also have other rights which vary from state to state Mega Lite 5718 Kenwick St san Antonio TX 78238 Ph 210 684 2600 Fax 210 855 6279 www mega lite com info mega lite com
6. here is no serviceable parts inside the device Maintenance and service operations are to be carried out by authorized dealers Should you have further questions please contact your dealer Parts List Warranty Information Warranty Conditions Unless otherwise stated in writing your product is covered by a one year parts and labor limited warranty LEDs are not guaranteed to match in color temperature or output It is the owner s responsibility to furnish receipts or invoices for verification of purchase date and reseller or distributor If purchase date cannot be provided date of manufacture will be used to determine warranty period Goods returned under warranty must follow the proper authorization procedure and must be accompanied by a copy of the original invoice Goods repaired under warranty will be returned to the owner with the freight prepaid by MSI via the most economical means of shipment Repair or replacement as provided for under this warranty is the exclusive remedy of the consumer MEGA SYSTEMS INC makes no warranties express or implied with respect to any product and Mega Systems specifically disclaims any warranty of merchantability or fitness for a particular purpose Mega Systems shall not be liable for any indirect inci dental or consequential damage including lost profit sustained or incurred in connection with any product or caused by product defect or the partial or total failure of any product re
7. vere electrical injures if you have doubts concerning the safety do not install When installing a unit it is very important that you follow common safety procedures Installing requires extensive experi ence including but not limited to calculating voltage loads material being used and periodic safety inspections If you lack these qualifications do not attempt the installation yourself instead use a professional electrician When installing the controller please make sure all safety rules are followed and it is installed in a appropriate housing Installation should be checked at least one time a year by a skilled person Cleaning and maintenance Cleaning Clean the front glass of the fixture with soap and warm water never clean with strong soluble deter gents Installation Maintenance The operator has to make sure that the unit is operating safely and has the installa tions and electronics checked by an expert every 2 years The following points have to be considered during the inspection 1 All screws used for installing the device or part of the device have to be tightly connected and must not be corroded 2 There must not be any deformations on the housing fixation and installation spot 3 The electronic power supply cables must not show any damages material fatigue e g porous cables or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any Note T

Download Pdf Manuals

image

Related Search

Related Contents

東芝マシンルームレスエレベーター取扱説明書    GpW500シリーズ - 有限会社 石松測器  Pulsuhr „Speedmaster“    ELIO®  Θ-7000 - QTC  NOVA 57080 Use and Care Manual  Mesa Para Computador Zanzini Peg Leve    

Copyright © All rights reserved.
Failed to retrieve file