User Manual - RF-Link
Contents
1. Contents wenn H 1 lImportant Safety Information 1 igita ire ess 2 Package ONteMt sessione ia a aa ai 3 Panel Layout and Function Receiver ees U J M I 1 Important Safety Information S e r S a n u a To prevent fire or shock hazard do not expose this product to rain and moisture For example do not use near a bathtub washbowl kitchen sink or laundry tub in a wet basement or nearby a swimming pool To avoid electric shock do not take apart this product provided as an accessory This product should be operated only under power supply Do not overload wall outlets and extension outlets as this can result in the risk of fire or electric shock This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Note This equipment has been tested and found to comply with the limits regulated by FCC and CE These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction may cause harmful interference to radio communications The change or modifcations not expressly approved by the party responsible for compliance could2. nd firmware pore Mm seas Exit System On Off wiplay Start Stop Start Stop program Adjust Adjust screen size WEEE Directive amp Product Disposal At the end of its serviceable life this product should not be treated as household or general waste It should be handed over to the applicable collection point for the recycling of electrical and electronic equipment or returned to the supplier for disposal CE TTD D5006R 408 000708 00
3. vided MD into your computer s CD drive 2 Open the MD s file from My Computer This will open up to a selection of software to be installed 3 Double click the execution file gy setup exe screen will appear 4 Follow the steps and click Finish to complete the driver installation 5 Now you can link the receiver from your PC Utilities Operation 1 When starting to use the PC to TV HDMI receiver please make sure your Wi Fi link is activated 2 Open the selection of software list and double click the execution file ats WiPlay exe and select your Wi Fi adapter which one you want to use Screen will be as follows Screen Scale Internet Shift 1 Choosing icon it will take a few seconds to search AP Router 2 Choosing AP Router you need 3 Click Connect 4 The receiver will restart by itself ct an AP Router Config Shift 1 Choosing icon 2 Choosing frequency you need 3 Click Save 4 Restart the receiver when screen show Save successful Channel selection button to find optional reception Installation 1 Connect the output device TV monitor home theatre etc through the HDMI cable 2 Connect the power supply adapter 3 Turn on the device The power LED will illuminate 4 3 Display Mode Mode icon Description Presentation prefer Presentation Oo Video Extension 4 4 Button Instruction Video prefer About Program version a
4. void the user s authority to operate the equipment To comply with the FCC RF exposure compliance requirements no change to the antenna or the device is permitted Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user s authority to operate the device 2 Package Contents Panel Layout and Function Check to make sure that all units shown as below are enclosed List of functions If something missed please contact your dealer 1 5 0GHz Receiver x 1 2 Stand x1 Receiver unit P i K A i N IZ N NL XA K VZ i F D NI VA i a BRK S Us 0 K s o i ee A N N O 5 K KA NI KD D A VIN PK N N A K R A A 5 N i i iD 5 N D K j 3 HDMI Cable x 1 1 USB port 2 CH change Reset button 3 On Off switch EUROPE Type 4 HDMI port 5 6 7 Mini USB port power only Link LED Power LED Press and hold this button within 3 seconds to change the channel Keep pressing over 3 seconds is to restart the system to default Orange LED illuminate when the transmitter links up with receiver and will flash when the data is under transmission Green LED illuminate when the power is on 4 Receiver Setup 4 1 4 2 4 5 4 6 4 7 Driver installation 1 Insert the pro
Download Pdf Manuals
Related Search