place the lifetone hl™ next to your bed with the speaker facing the
Contents
1. retrain the clock to operate without a bed shaker Ub NOTE Any time that you want to restore use of the bed shaker simply plug it in Battery ERROR wNE PEPE FLASHING le A ee E S R Lu a n m bd Leos SU Bed shaker ERROR Bed shaker unplugged PLEASE READTHE USER S MANUAL COMPLETELY AND THOROUGHLY FOR FURTHER DIRECTIONS PRODUCT FEATURES AND WARRANTY INFORMATION a lifetone TECHNOLOG Y For more information go to www lifetonesafety com or call Customer Service 1 800 648 7923 800 Research Parkway Suite 339 Oklahoma City OK 73104 MODEL HLAC150 KEEP THIS QUICK START GUIDE IN A SAFE PLACE Doc LTQSG150 1108312. minute press or 3 Press ON OFF to enable or disable the wake up alarm The bell icon at lower left will appear or disappear to indicate whether the alarm is active or inactive You can adjust the volume of your wake up alarm to high or low with the HI LO slider switch on top If there is a fire emergency the alarm will sound at maximum volume NOTE Any time that you need to reset the wake up alarm time press and hold SET ALARM until the hour is flashing and repeat all parts of STEP 4 TROUBLESHOOTING ERROR MESSAGES Batteries If the clock is flashing BATT and beeping at one minute intervals the batteries were not installed were installed with the wrong polarity or are below the required voltage Remove and insert them again or replace them if necessary Be sure to match the polarity and signs in the battery compartment To keep your compatibility set up leave the clock plugged in while you change batteries M MEUSI 6 Ayh BEEP Bedshaker If the screen is flashing beds and the clock beeps the bed shaker has come unplugged Seat the bed shaker plug firmly into the jack on the back of the clock NOTE Ifyou decide you don t want to use the bed shaker after it has been installed unplug the bed shaker then press and hold the red TEST SILENCE button on the back of the clock for 2 seconds That starts a manual self test that will display TEST for 10 to 20 seconds sound the fire alarm once and
3. QUICK START GUIDE LIFETONE HL BEDSIDE FIRE ALARM AND CLOCK MODEL HLAC150 Thank you for purchasing the Lifetone HL Bedside Fire Alarm and Clock These items are included LIFETONE HL Bedside Fire Alar amp Clock alifetone 4 D Cell Alkaline Batteries HLAC150 User s Manual HLAC150 Bed Shaker PLACE THE LIFETONE HL NEXT TO YOUR BED WITH THE SPEAKER FACING THE PILLOW STEP 1 POWERING THE HLAC150 1 Remove the battery door located on the back of your clock 2 Insert four D cell alkaline batteries as shown in the illustration at right matching the polarity and signs in the open compartment 3 Replace the battery door securely 4 Plug the Lifetone HLAC150 into an electrical outlet near your bedside aps ao j 5 You may plug the bed shaker in on the back of the clock now C or at any time after it has been set up Install 4 D Cell The word TEST will now be flashing on the screen Go to STEP 2 Alkaline Batteries Plug in Bed Shaker NOTE The batteries are for backup in the event of a power outage only The HLAC150 is not meant to operate on batteries alone STEP 2 SMOKE ALARM COMPATIBILITY This important test will determine if your smoke alarms are compatible with the Lifetone HL Press TEST SILENCE 1 The word TEST is flashing on the screen Press the red TEST SILENCE button on button to start the test the back of the clock The w
4. ord TEST will stop flashing for 30 to 50 seconds 2 When TEST starts flashing again locate the most distant smoke alarm you want detected 3 Press and hold the test button on the smoke alarm until the Lifetone HL alarm sounds Between 2 and 6 smoke alarm T3 cycles groups of 3 beeps will be required This takes about 10 to 30 seconds SFLASHINGE 4 When the Lifetone HL alarm sounds and FIRE appears on the screen the test has been successful 5 To stop the alarm press the red TEST SILENCE button on the back of the clock enokealane hasbeen deteces 6 If all tests are passed the 12 hr time display option will flash on the Press TEST SILENCE screen and you may now set the clock Go to STEP 3 button to silence alarm NOTE If the clock is flashing all segments as shown below and beeping at short intervals your smoke alarm was not detected or is not compatible with the LIFETONE HL TITRA IITIL lt v i Gh emmm sia S i BEEP BEBBIBE Bes SS SENASHINGS Unplug the clock and remove one battery Repeat the set up beginning with r STEP 1 POWERING THE PRODUCT You may need to choose a closer smoke alarm x If the compatibility test fails again the smoke alarm may not be compatible Unplug e D I su the clock and remove the batteries See the section titled UNSUCCESSFUL SMOKE Successful test You may ALARM COMPATIBILITY TEST in the user s manual no
5. w set the clock KEEP THIS QUICK START GUIDE IN A SAFE PLACE Doc LTQSG150 110831 STEP 3 SETTING THE CLOCK Buttons on the top of the Lifetone HL On the time display 12hr is flashing To select 24 hour time press or ProNioFF HI LO SETALARM SET CLOCK 2 Press SET CLOCK The hour will flash To change the hour press or O Q O 3 Press SET CLOCK The minute will flash To change the minute press or 4 Press SET CLOCK The year will flash To change the year press or 5 Press SET CLOCK The small m and d will flash To change to a day first display of the date press or 6 Press SET CLOCK The month will flash To change the month press or N Press SET CLOCK The day will flash To change the day press or 8 Press SET CLOCK The E for English will flash To change to Spanish or French press or Press SET CLOCK again YEAR LANGUAGE 9 The clock will show the day of the week to the right of the date DAY OF WEEK If you prefer to display the year instead press SET CLOCK again NOTE Any time that you need to reset the clock press and hold SET CLOCK until the flashing 12hr appears and repeat all parts of STEP 3 iA D b ORDAY OR MONTH STEP 4 SETTING THE WAKE UP ALARM 1 Press and hold SET ALARM until the wake up hour flashes To set the hour press or 2 Press SET ALARM The minute will flash To set the
Download Pdf Manuals
Related Search