L6178--TK230 User manual Booklet
Contents
1. EB 210 12 Electric Brush Use this powerbrush to Adjustment Knob vacuum wall to wall carpeting handmade carpets fine rugs and other flooring This powerbrush must be used with the top and lower wands The overload protector pro tects the motor jamming and be If the brush stops the overload pro protector turn t Belt Replacement EB21010 Pile Height Light Bulb Replacement EB21016 Light Cover Edge Cleaner not shown from brush Overload Protector t breakage reset button or is stalled tector will shut the brush off To reset the overload he vacuum off press the reset button on the brush Now you may turn your vacuum back on and continue cleaning Features include 3 level height adjustment adjusts to match surface being c Soft Bumper wraps around brush to protect baseboards and furniture s Reset Button A flat belt drive with a belt protector reset trouble free service leaned button means years of REMEMBER As remove brush pull with all electric appliances risk of shock is possible Do not wands out or attempt maintenance while power is on Wands 1 e 2 1 EB368793 Lower Wand Connects to top wand when operating the floor brush Curled end connects to top wand other end is inserted into electric brush 2 W 540 Top Wand Connects to lower wand when operating the floor brush Cord management keeps co2. d lifting both sides as shown 2 Push in and turn bulb to remove 3 Replace bulb and snap light cover in place Note replacement bulb number is EB21016 BELT CHANGING AND BRUSH CLEANING EB 210 SuperGroom II Disconnect hose and brush from electrical outlet Frequently check and remove hair string and lint buildup in the EB 210 SuperGroom II brush area If buildup becomes excessive disconnect EB 210 SuperGroom II from wand and follow steps below To Remove 1 Raise the pile height adjustment rollers Remove the two cover screws from the EB 210 SuperGroom aa II base 2 Insert and twist flat screwdriver under both back cover tabs 3 Turn EB 210 SuperGroom II right side up Tilt cover forward from back until front snaps free f a a 4 Carefully insert and lift screwdriver at each brush support to free brush from base a 5 Remove belt from motor shaft 7 Slide brush supports off to check and clean brush support areas See Brush Assembly EB 210 SuperGroom II for picture of complete brush To Replace 1 Slide on washers and brush supports 2 Install new belt in belt groove on the brush assembly then over motor shaft as show Note Replacement belt number is EB21010 6 3 Insert both front support tabes into base slots Then snap brush supports into place 4 Line up tabs on front of base with slots inside the cover front Base Tabs 5 T
3. ilt cover to back Press cover firmly until rear tabs snap into place Turn EB 210 SuperGroom II over replace the cover screws and lower the pile height adjustment rollers into place BRUSH SERVICING EB 210 SuperGroom II Disconnect hose and brush from electrical outlet and disconnect EB 210 SuperGroom II from wand so brush will not operate while being serviced To Check When brush is worn to the level of the base support bars replace the brush Base Support Bar To Replace Remove light cover EB 210 SuperGroom II cover belt and brush assembly follow to remove section in Belt Changing and Brush Cleaning K 1 Remove brush support and washers from brush assembly 2 Remove brush assembly and replace with new brush 3 Reassemble brush assembly 4 Replace belt brush assembly EB 210 SuperGroom IITM cover EB 210 SuperGroom II Parts List Please note when ordering that you must include the identification number for the brush For the EB 210 SuperGroom II this is EB210 i e to order a light bulb you would order an EB21016 Belt Floor nozzle lower unit Motor assembly Motor bracket Overload protector Light bulb Light bulb socket Swivel catch Swivel Furniture guard Roller shaft Swivel bearing seal Nozzle roller Front axle assembly Brush and bearing assembly Window cover not shown Cord and plug assembly not shown Power head cover assembly not shown Floor nozz
4. le upper unit not shown 8 L6178 27 D G7 26 BRUSH ASSEMBLY EB 210 SuperGroom II GH Brush S a s e Brush vi K Support Washer bk s ay ef na Belt Groove e Brush Support i Washer
5. rds out of the way and allows you to disengage the hose handle from the electric brush 3 Electric Brush Assembly amp Use Wand Insertion and Release For the EB 210 insert wand snap wand button into place Turn wand button past the stop position This DO NOT attach or remove handle or wands while cleaner is ON This could cause sparking and damage the electrical contacts HOW TO START EB 210 SuperGroom II Model 1 To lower wands hold EB 210 SuperGroom II HD down with foot and pull back on wands 2 Start vacuum and electric brush Pile height adjustment for the EB 210 Rotate the pile height control The pile height setting is shown on the control The deeper the pile of the carpet the higher the setting OVERLOAD PROTECTOR The overload protector protects the motor from brush jamming and belt break age If the brush stops the overload protector will stop the electric brush Overload Protector reset button To correct problem Unplug the electrical cord Check brush area for excessive lint buildup or jamming To reset Press reset button on top of the brush Plug in and turn on vacuum and brush EB 210 SuperGroom II Care 71 WARNING Electric Shock Hazard Disconnect electrical supply before servicing or cleaning the unit Failure to do so could result in electrical shock or personal injury LIGHT CHANGING EB 210 SuperGroom II 1 Remove light cover by pressing in an
Download Pdf Manuals
Related Search