HD IR Vandal Proof Network Dome Camera
Contents
1. 0 Alarm Input i Collecting Do GND Figure 1 4 Please refer to the following figure for alarm output information See Figure 1 5 Alarm output Alarm output is OC door requiring increase of external pull up resistor Output signal is high and low levels After pull up resistor is increased output signal is high level by default When there is alarm output output signal becomes low level 10k Alarm Output I collecting GND Figure 1 5 2 Device Installation 2 1 Installation Steps Important Before the installation please make sure the installation environments can at least support 3x weight of the camera Please follow the steps listed below to install the device Please refer to Figure 2 1 for reference Step 1 Use inner hex wrench in the accessories bag to open dome enclosure by unfastening three inner hex screws on enclosure Step 2 Please take the installation position map in the accessories bag and then paste it on the ceiling or the wall according to your monitor area requirements Step 3 Find cross signs on the map and dig three plastic expansion bolts holes in the installation surface and then insert three expansion bolts in the holes Secure these three bolts firmly Note f use pulls out cable from top of installation surface you must dig a exit hole on installation surface according to the installation position map f user pulls out cable from side of cable channel i2. proper power cut off device during the installation connection Always follow the instruction guide the manufacturer recommended 4 Qualified engineers needed All the examination and repair work should be done by the qualified service engineers We are not liable for any problems caused by unauthorized modifications or attempted repair 5 Environment This series network camera should be installed in a cool dry place away from direct sunlight inflammable explosive substances and etc Please keep it away from the electromagnetic radiation object and environment Please make sure the CCD CMOS component is out of the radiation of the laser beam device Otherwise it may result in CCD CMOS optical component damage Please keep the sound ventilation Do not allow the water and other liquid falling into the camera Thunder proof device is recommended to be adopted to better prevent thunder The grounding studs of the product are recommended to be grounded to further enhance the reliability of the camera 6 Daily Maintenance Please shut down the device and then unplug the power cable before you begin daily maintenance work Do not touch the CCD CMOS optic component You can use the blower to clean the dust on the lens surface Always use the dry soft cloth to clean the device If there is too much dust please use the water to dilute the mild detergent first and then use it to clean the device Finally use the dry cloth to clean
3. HD IR Vandal Proof Network Dome Camera Quick Start Guide Version 1 0 1 Welcome Thank you for purchasing our network camera This quick start guide is designed to be a reference tool for your system Please keep this start guide well for future reference Please open the accessory bag to check the items one by one in accordance with the list below Contact your local retailer ASAP if something is missing or damaged in the bag Before your operation please read the following instructions carefully 1 Electrical safety All installation and operation here should conform to your local electrical safety codes The power shall conform to the requirement in the SELV Safety Extra Low Voltage and the Limited power source Is rated 12V or 24V AC DC in the IEC60950 1 Refer to general introduction Please note Do not connect two power supplying sources to the device at the same time it may result in device damage The product must be grounded to reduce the risk of electronic shock We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation We are not liable for any problems caused by unauthorized modification or attempted repair 2 Transportation security Heavy stress violent vibration or water splash are not allowed during transportation storage and installation 3 Installation Do not apply power to the camera before completing installation Please install the
4. address and etc Select one IP address and then right click mouse you can see an interface is shown as in Figure 3 1 Select the Open Device Web item you can go to the corresponding web login interface Device List SN__ IP Address ____ Port Subnet Mask __ Default Gateway Mac Address Ea L OTTI 255 255 2550 192 168 11 S002 a9 7b S0 lt Tip You can click login button directly and information to login ip then input corresponding inf log Al 7 Figure 3 1 Search interface If you want to modify the device IP address without logging in the device web interface you can go to the configuration tool main interface to set In the configuration tool search interface please select a device IP address and then double click it to open the login interface Or you can select an IP address and then click the Login button to go to the login interface See Figure 3 2 In Figure 3 2 you can view device IP address user name password and port Please modify the corresponding information to login Please note the port information here shall be identical with the port value you set in TCP port in Web Network interface Otherwise you cannot login the device If you are using device background upgrade port 3800 to login other setups are all invalid IP Address 192 168 1 108 User Mame fadmin FERE Password Port 37777 el Figure 3 2 Login prompt After you logged in the configuration t
5. ccceececeeeeseeeeseeeeseeeeseeeesees 12 111 1 Structure 1 1 Components Note There are differences about wire structure for some product models please refer to the actual object for more details You can refer to the following figure for component structure See Figure 1 1 Figure 1 1 Component structure Please refer to the following sheet for detailed information Component Name Dome body Dome enclosure Pon ronne SiMe Power input port Port 3 Connect to DC 12V power input power Alarm signal input output optional Upon supported by some product models Network data in out and PoE Note Port 5 Internet access port Some devices do not support PoE Before making crystal head pull the anti dust waterproof cover through network cable Input audio signal receive analog audio Port 6 Audio input port signal from sound pick up etc optional supported by some product models Output audio signal to speakers etc Port 7 Audio output port optional supported by some product models Please refer to the following sheet for detailed information about I O port Port Port Ae ALARM _IN1 Alarm input port receive on off signal of external alarm source I O Port D ALARM OUTI Alarm output port output alarm signal to alarm device ALARM_GND Connect ground 1 2 Framework and Dimension Please refer to the following two figures for dimension information The unit is mm See Figure1 2 Figur
6. corresponding local authorities to process according to your local government statutes Note This quick start guide is for reference only Slight difference may be found in user interface All the designs and software here are subject to change without prior written notice All trademarks and registered trademarks mentioned are the properties of their respective owners If there is any uncertainty or controversy please refer to the final explanation of us Please visit our website or contact your local service engineer for more information 12
7. e1 2 1 3 Alarm Setup Note Only supported by some series products IP Camera ive pias f soup alarm Logout Camera Relay Activation Network T Enable Event Relay in Alarm1 gt gt Video Detect Working Period gt Abnormality Anti Dither 0 Second 0 100 Sensor Type NO Storage Iv System Record Information Record Delay Second 10 300 Iv Relay out Alarm Delay Second 10 300 T Send Email Tl Snapshot Figure1 3 Alarm input output description Step 1 Connect alarm input device to the alarm input of I O cable Step 2 Connect alarm output device to the alarm output of I O cable alarm output is collector open circuit output which connects 10K resistor to 3 3V externally Step 3 Open the Web set alarm input and output correspondingly Alarm input on WEB corresponds to I O cable on device When there is alarm alarm input device will generate signal of high and low level Set corresponding NO and NC inputs Step 4 Set the WEB alarm output The alarm output is for the alarm output port of the device It is the alarm output port of the I O cable Please refer to the following figure for alarm input information See Figure 1 4 Alarm input When the input signal is idle or grounded the device can collect the different statuses of the alarm input port When the input signal is connected to 3 3V or idle the device collects the logic 1 When the input signal is grounded the device collects the logic
8. evice to power When you need to use WPS function press the Reset button in Figure 2 2 for 1 to 2 seconds while connecting device to power then press WPS button on the router Generally the device can be connected to corresponding router within 1 minute Supported by some series products Step 6 Take dome enclosure put it back on the camera properly regarding to screw and hole and fasten the three inner hex screws with wrench 2 2 Micro SD Card Installation Note Some series products do not support the Micro SD card storage function Please shut down the power and then turn off the device before you install the Micro SD card Step 1 Find the Micro SD Card slot in figure 2 2 open the Micro SD Card slot according to the direction in figure 2 3 Step 2 Adjust the Micro SD Card to proper direction and install it in the Micro SD card slot Step 3 According to the direction in figure 2 4 close the Micro SD card slot and keep it locked Figure 2 4 Micro SD Card installation illustration 2 3 Quick Configuration Tool 3 1 Overview Quick configuration tool can search current IP address modify IP address At the same time you can use it to upgrade the device Please note the tool only applies to the IP addresses in the same segment 3 2 Operation Double click the Config Tools exe icon you can see an interface in the device list interface you can view device IP address port number subnet mask default gateway MAC
9. low See Figure 4 2 Please input your user name and password Default factory name is admin and password is admin Note For security reasons please modify your password after you first login 10 Usemame Eton cae Figure 4 2 Web login After you successfully logged in please install WEB plug in unit Please refer to the Web Operation Manual included in the resource CD for detailed operation instruction See Figure 4 3 IP Camera er eee Protocol TCP V Oa aa Bi gt amp E Figure 4 3 Web monitoring window 11 Appendix Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Name Cr VI PBB Component we aaa O Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ T11363 2006 standard X Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ T 11363 2006 standard During the environmental friendly use period EFUP period the toxic or hazardous substance or elements contained in products will not leak or mutate so that the use of these substances or elements will not result in any severe environmental pollution any bodily injury or damage to any assets The consumer is not authorized to process such kind of substances or elements please return to the
10. ool main interface is shown as below See Figure 3 3 NetWork Parameter PPPOE System nA System Upgrade General Parameter DHCP Enable hpv v IP Address 192 168 1108 Subnet Mask 255 255 0 0 Gateway 05 04 Mac Address 90 02 a9 7f d8 21 Figure 3 3 Main interface For detailed information and operation instruction of the quick configuration tool please refer to the Quick Configuration Tool User s Manual included in the resources CD 4 Web Operation This series network camera products support the Web access and management via PC Web includes several modules Monitor channel preview system configuration alarm and etc 4 1 Network Connection Please follow the steps listed below for network connection Make sure the network camera has connected to the network properly Please set the IP address subnet mask and gateway of the PC and the network camera respectively Network camera default IP address is 192 168 1 108 Subnet mask is 255 255 255 0 Gateway is 192 168 1 1 Use order ping network camera address to check connection is OK or not 4 2 Login and Main Interface Open IE and input network camera address in the address bar See Figure 4 1 Blank Page Windows Internet Explorer Sis about blank Lt Input your IP re ww Blank Page v D fy v Page Tools address here Internet R100 Figure 4 1 IP address The login interface is shown as be
11. t must go through the U shape channel on dome pedestal and take out cable from the side exit hole on pedestal Step 4 Adjust the device installation pedestal to the proper position and then pull cable through the exit hole on Installation surface Make direction of TOP sign same as it on installation position map Line up the three screw holes in the device pedestal to the three plastic expansion bolt holes in the installation position Put the three self tapping screws in the three plastic expansion bolts firmly Fix dome body on installation surface Step 5 Hold bottom of bracket with hand horizontally rotate bracket adjusting lens direction to designated position Loosen one M2 screw on LED decoration cover loosen only do not take it down hold the decoration cover with hand making lens rotate vertically Adjust vertical direction of lens to appropriate angle and fasten the M2 screw Range of lens vertical 0 65 horizontal 0 355 See Figure 2 2 Expansion bolt Dome body 74 2 self tapping screw Dome enclosure Fixed screw Screw of LED SD card slot decoration cover Reset button j Ji J j Ii j I j li I li i li ji i H ii Hi j H Ji i i j HH i Hi j _ y Figure 2 2 Device installation illustration 2 Note When you need to reset the device press the Reset button in Figure 2 2 for 10 seconds while connecting d
12. the device Please put the dustproof cap to protect the CCD CMOS component when you do not use the camera Dome enclosure is the optical component do not touch the enclosure when you are installing the device or clean the enclosure when you are doing maintenance work Please use professional optical clean method to clean the enclosure Improper enclosure clean method such as use cloth may result in poor IR effect of camera with IR function 7 Accessories Be sure to use all the accessories recommended by manufacturer Before installation please open the package and check all the components are included Contact your local retailer ASAP if something is broken in your package Accessory Name Network Camera Unit Quick Start Guide Installation Accessories Bag CD 1i Table of Contents SU IG WUC ascent sone shat ceas tatesas E E A 1 1 1 COMPONETS aooe NE RN 1 1 2 Framework and DIMENSION Gresinin a 2 Wr ATO Uee E E E EE A 3 DEVICE INSANA lOean A A aden 5 2 1 Mealaton EDS eaaa een Bee Oro er Oe Ror eer enone ater 5 2 2 Miro SD Gard INStallatOn sena 7 QUICK GONTGUPATION TOON ssicacucst sca cecaesoaeacabactaucoeassaycabseniwcnn soaaudab acaunsnt A 8 3 1 OVS VOW spins dees aaa E ERT RE I RERE 8 32 OPOaren ene n a a oe 8 WEDDE UO e 10 4 1 NEIWOIK CONNECUOM erreurs nee EER AEA 10 4 2 LOGIN and Main IMCMACC sais snietisuco tiie tidus SiisteG iia Sambal tes 10 Appendix Toxic or Hazardous Materials or Elements cccc
Download Pdf Manuals
Related Search