E180 BTA Manual
Contents
1. Opening the laser units can result in hazardous radiation and will invalidate the manufacturer war ranty If starting the machine to be measured would result in injuries the possibility to unintentionally start 1t must be disabled before mounting the equipment for example by locking the switch in the off po sition or removing the fuses These safety precautions should remain in place until the measurement equipment has been removed from the machine Nofe The system should not be used in explosive risk areas Manuals as PDF You can download our manuals in pdf format from our website The pdf s are also available on the USB memory stick that 1s delivered with most systems EasyLink The new version of our database program EasyLink is available on the USB memory stick that is delivered with most systems You can always download the latest version from damalini com gt download gt software Travelling with your measurement system When travelling by airplane with your measurement system we strongly recommend that you check which rules apply for each airline company Some companies countries have limitations for checked baggage when it comes to items including batteries For information about Easy Laser batteries please see system unit details in the end of this manual It is also good practice to remove the batter ies from the equipment when possible e g D22 D23 and D75 English Limited warranty This product is man2. On Off i Battery Different sheave width y If the sheaves have different face widths just add or sub ii tract the difference from the zero value to get the value for perfect alignment 1 mm 0 040 2 mm 0 080 Settings Press to open the settings view Use J to move up and down in the menu e Press f amp to switch position on the M and S unit Toggle between mm and inch with 8 Battery Press to see the battery status of the detector While the battery is charging there is a green flashing light The laser transmitter flashes when the battery is low Change the batteries before you continue to measure Red flashing once Battery empty O g ry empty Note gt Red flashing twice Battery needs charging If not using the system for a long pe riod of time remove the battery from O Green flashing three times Good the laser transmitter Green fixed light Battery full Align with targets Aligned sheaves The beam disappears in the slot of the target Laser beam English Adjust Start by adjusting the sheave and then the machine When you adjust the machine one way 1t often affects the machine s other alignment conditions Which means this process may have to be repeated several times Offset Offset mm or inch Correct offset by moving the movable machine with axial jackscrews or by repositioning one of the sheaves on its shaft Horizontal angle Ver
3. E3 Bluetooth MANUAL English 05 0728 Revision 1 0 System version 1 0 English Damalini AB Damalini AB develops manufactures and markets Easy Laser measurement and alignment equip ment based on laser technology We have more than 25 years of experience from measurement tasks in the field and product development We also provide measurement service which means that we ourselves use the equipment we develop and continuously improve 1t Because of this we dare to call ourselves measurement specialists Do not hesitate to contact us about your measurement prob lems Our expertise will help you solve it in an easy way Declaration of conformity Equipment Easy Laser product range Damalini AB declares that the Easy Laser product range is manufactured in conformity with national and international regulations The system complies with and has been tested according to the following requirements EMC Directive 2004 108 EG Low Voltage Directive 2006 95 EC Laser Classification EN 60825 1 and complies with 21 CFR 1040 10 and 1040 11 except for deviations pursuant to Laser Notice No 50 dated June 24 2007 RoHs Directive 2002 95 EG WEEE Directive 2002 96 EG For Bluetooth devices This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference 2 this device must accept any interference received including interference that may ca
4. i is not responsible for data that may be lost or damaged during transit or repair Lithium Ion battery limited warranty Lithium ion batteries inevitably lose power during their lifetimes depending on usage temperatures and the number of charging cycles Therefore the internal rechargeable batteries used in the E series are not included in our general 2 year warranty There is a 1 year warranty for the battery capacity not to fall below 70 a normal change means that the battery must have more than 70 capac ity after more than 300 charging cycles A 2 year warranty applies if the battery becomes unusable because of a manufacturing fault or factors that Damalini AB could be expected to have control of or if the battery displays abnormal loss of capacity in relation to use Extended warranty Easy Laser Measurement and Alignment Systems meet the highest quality standards For this reason we have extended the warranty to you to a total of 3 years free of charge The prerequi site for a warranty extension is that you register your system parts on the Internet within 6 months of purchase The warranty period begins on the date of purchase The warranty extension applies to all products in accordance with the Easy Laser Warranty requirements English Service and calibration Our Service centres will quickly assist you if your measurement system need to be repaired or when it is time for calibration Our main Service centre is l
5. imensions BxHxD 145x86x30 mm 5 7x3 4x1 2 Battery Alkaline 1xR6 AA 1 5 V Weight 270g 9 52 oz Connector Detector unit gt 060 mm 2 5 Up to 3m 9 87 between transmitter and detector Sheave diameters Measurement distance Detector aperture Measurement range Axial offset 3 mm 0 12 Angular value 8 Display resolution Display type Connection Battery type Battery operation Material Dimensions BxHxD Weight Targets Charger Carrying case 10 Offset 0 1 Angle 0 01 Yellow OLED 96x96 pixels Bluetooth wireless technology Li lon 5 hours continuously ABS plastics Anodized aluminium 95x95x36 mm 3 7x3 7x1 4 190 g 6 7 oz 2 pcs magnet targets with adjustable center line 100 240 V AC with cable WxHxD 270x225x80 mm 10 6 x8 8 x3 1 11
6. ocated in Sweden There are several local Service centres that are certi fied to carry out limited service and repair Contact your local Service centre first before sending your equipment for service or repair All Service centres are listed on our web site under Service and Calibration Before sending your measuring system to our main Service centre fill in the online Service and Repair report www easy laser service com Compatibility The E series 1s not compatible with previous analogue units from the D series You can however continue to use previous brackets Disclaimer Damalini AB and our authorized dealers will take no responsibility for damage to machines and plant as a result of the use of Easy Laser measurement and alignment systems Copyright Damalini 2013 We might change and correct the manual in later issues without further information Changes to the Easy Laser equipment may also affect the accuracy of the information September 2043 pte E Fredrik Eriksson Quality Manager Damalini AB Damalini AB PO Box 149 SE 431 22 M lndal Sweden Phone 46 31 708 63 00 E mail info damalini com Web www damalini com English BTA Easy Laser BTA system consists of a laser transmitter and a detector Magnetic mountings on laser and detector make 1t easy to mount the equipment All types of sheave pulleys can be aligned regardless of belt type You can compensate for sheaves of varying widths The misalignmen
7. t can be offset or angular It can also be a combination of both a Offset misalignment Angular misalignment Offset and angular misalignment Preparations e Check the sheaves for radial runout Bent shafts will make it impossible to perform an accurate alignment e Check the sheaves for axial runout If possible adjust with the mounting screws of the bush ings e Make sure that the sheaves are clean from grease and oil Mount the units The units are mounted on a flat machined surface with magnets The magnets are very strong try to soften the touch by putting just one magnet to sheave first then turning the other ones in Non magnetic sheave pul leys can be aligned as the units are very light and can be mounted using double sided tape 1 Mount the laser transmitter on the stationary machine 2 Mount the detector on the movable machine Thanks to the clever sth 3 Make sure all magnetic surfaces are in contact with the sheave as Wo As arge Movable Stationary Stationary Movable On steel surface On non magnetic object All of the magnetic surfaces must be in contact with the object Magnetic areas English Measure 1 Press O to start the detector and ON to start the laser transmitter Offset mm or inch Horizontal angle 2 Read the values Offset horizontal angle and vertical Vertical angle 19101 ang e are cep ayed Settings 3 Adjust machine see next page
8. tical angle Vertical Correct vertical angular error by shimming the movable machine Horizontal Correct horizontal angular error by adjusting the movable machine with lateral jackscrews E mm m mils inch Tolerance Recommended maximum tolerances from manufacturers of belt transmissions is 0 25 0 50 Recommendations are always dependent on belt type Please consult the design manual of the specific belt type Recommended Connect to a Display unit The E180 BTA can be used as a separate tool It also works with the BTA program in the Display unit of the systems E710 E540 E530 and most of the E9xx systems Please see corresponding manual In the Display unit the values are displayed live You can also save the results in the Display unit and generate a PDF report Enter distance F1 F2 1 32000 mm Results BTA vertical and horizontal The program guides you on how to mount the Shim and adjustment values are displayed live units on the sheaves English Technical data E180 BTA Part No 12 0796 Laser transmitter Sheave diameters gt 60 mm 2 5 Laser class 2 Output power lt 1 mW Laser wavelength 635 670 nm Beam angle 60 Accuracy Laser plane Reference plane Parallelity lt 0 05 Offset lt 0 2 mm 0 008 Battery type 1xR6 AA 1 5 V Battery operation 8 hours continuously Operating temperature 10 C to 50 C Material ABS plastics Hard anodized aluminium D
9. ufactured under Damalini s strict quality control system Should the product fail within two 2 years from the date of purchase under normal usage conditions Damalini will repair or replace the product free of charge 1 Using new or refurbished replacement parts 2 Exchange the product with a product that 1s new or which has been manufactured from new or serviceable used parts and is at least functionally equivalent to the original product Proof of purchase date should be confirmed and sent together with a copy of the original purchase document Warranty is valid under normal usage described in the user s manual appended with the product The warranty comprises failure on Easy Laser product that could be related to material and or fabrication errors The warranty 16 valid only in the country of purchase The warranty is not valid in the following cases e Ifthe product is broken due to mishandling or incorrect operation e If the product has been exposed to extreme temperature calamity chock or high voltage e If the product has been modified repaired or disassembled by unauthorized personnel Compensation for possible damage due to failure on Easy Laser product is not included in the war ranty Freight cost to Damalini is not included in the warranty Nofe Before delivery of the product for warranty repair it is the responsibility of the buyer to backup all data Data recovery is not included in the warranty service and Damalin
10. use un desired operation Disposal of old electrical and electronic equipment Applicable throughout the European Union and other European countries with separate collection programs This symbol found on product or on its packing indicates that this product should not be treated as household waste when disposed of It should be handed over to an applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed correctly you will help to prevent potential negative consequences to the environment and human health For more detailed information about the recycling of this product please contact your local city office household waste disposal service or the retail store where you purchased this product English Quality certificate Damalini AB is ISO 9001 2008 certified Certificate number 900958 Damalini AB confirm that our products are produced according to applicable national and interna tional regulations and standards All components are checked before assembly and final products are tested in functionality and visually checked before delivery The calibration of the equipment fully complies with ISO9001 2008 7 6 Safety precautions Easy Laser is a laser instrument in laser class II with an output power less than 1 mW which requires the following safety precautions e Never stare directly into the laser beam e Never aim the laser beam at anyone else s eyes Nofe
Download Pdf Manuals
Related Search