LPC2 EO1 User Manual
Contents
1. 0 Ox 0 Block 1 In Low Ox 0 0x 9 0x 8 Meaning status N A Switch On Switch Off Example of EnOcean actuator device Block 1 Out High Ox 0 Ox 0 Ox 0 Block 1 Out Low Ox 0 0x9 Ox 8 Meaning status N A Contact Contact On Off Working mode with LPC 2 controller After the setting parameters were stored into EEPROMs the module is ready to run LPC 2 EO1 and or other EnOcean devices are linked up on input device Inx ID Byte0 Inx ID Byte3 Inx ORG and output Outx ORG data Set the DIP Switch on LPC 2 EO1 module to lt SW1 On SW2 0ns5 Normal Operation mode Disconnect the PMC serial cable Data of devices is transferred between LPC 2 EO1 module and main control unit In devices Data block variables there are 4 bytes for each device that are received or transmitted over EnOcean wireless network Meaning of the values corresponds to each device specifications Please check the manufacturers device specification user manual for details Example of EnOcean switch device EOL 1 iDatal 3 Ox 0 Ox 0 Ox 0 EOL 1 iDatal 2 Ox 0 Ox 0 Ox 0 EOL 1 iDatal 1 Ox 0 Ox 0 Ox 0 EO1 1 iDatal 0 Ox 0 0x9 Ox 8 Meaning status N A Switch On Switch Off Example of EnOcean actuator device EO1 1 oDatal 3 Ox 0 Ox 0 Ox 0 EOL 1 oDatal 2 Ox 0 Ox 0 Ox 0 EOL 1 oDatal 1 Ox 0 Ox 0 Ox 0 EO1 1 oDatal 0 Ox 0 0x9 0x 8 Meaning N A Contact Contact command On Off 112. does not include damage due to transport or because of unconsidered corresponding regulations of the country where the module is installed This device must be connected properly by the provided connection scheme in this manual Misconnections may result in device damage fire or personal injury Hazardous voltage in the device can cause electric shock and may result in personal injury or death NEVER SERVICE THIS PRODUCT YOURSELF This device must not be installed in the systems critical for life e g medical devices aircrafts etc If the device is used in a manner not specified by the manufacturer the degree of protection provided by the equipment may be impaired B Waste electrical and electronic equipment WEEE must be collected separately LONGO LPC 2 complies to the following standards lt EMC EN 61000 6 2 EN 50082 EN 61000 6 4 EN 50081 e LVD IEC 61131 2 lt Vibrations and climatic mechanical EN 60068 2 6 EN 60068 2 27 EN 60068 2 29 Smarteh d o o operates a policy of continuous development Therefore we reserve the right to make changes and improvements to any of the products described in this manual without any prior notice MANUFACTURER SMARTEH d o o Trg tigrovcev 1 5220 Tolmin Slovenia C mms Longo programmable controller LPC 2 EO1 EnOcean module SMARJIFEH LIVING SYSTEMS Index Longo programmable controller LPC 2 EO1 EnOcean module 1 DESCRIPTION rencont aaiae daa aa aaa
3. 0189 and the next one 00000191 mas Longo programmable controller LPC 2 EO01 EnOcean module SMARJIFEH LIVING SYSTEMS 4 TECHNICAL SPECIFICATIONS Table 5 Technical specifications Power supply from internal BUS Number of EnOcean devices 5 EnOcean receivers and 5 EnOcean supported transmitters EnOcean radio standard 868 MHz or 315 MHz Max power consumption 0 5 W Dimensions L x W x H 90 x 18 x 60 mm Weight 50g Ambient temperature O to 50 C Ambient humidity max 95 no condensation Maximum altitude 2000 m Mounting position vertical T 20 to 60 C Pollution degree 2 Protection class IP 30 3 Ee Longo programmable controller LPC 2 EO1 EnOcean module SMARJIFEH LIVING SYSTEMS 5 APPENDIX SETUP PARAMETER PROCEDURE To define EnOcean devices with which LPC 2 EO1 module will communicate send or receive data next procedure must be executed For any additional information please contact Smarteh technical support The procedure consists of following steps selection of the LPC 2 HW configuration with LPC 2 EO1 module using LPC Composer SW tool EnOcean devices determination mode using EnOcean WinEtel SW communication tool setting up devices definition data into LPC 2 EO1 module using LPC Tester SW tool writing application program on LPC 2 main control unit using LPC Manager SW tool Selection of LPC 2 HW configuration LPC 2 EO1 is one of the
4. I O modules that is mounted on the right side of LPC 2 main control unit The HW configuration must be done with LPC Composer For application programming LPC Manager SW is used for details please refer to LPC Composer and LPC Manager User Manual EnOcean devices determination mode with LPC 2 EO1 module Start the WinEtel WinEte exe on the PC It can be downloaded from EnOcean website WinEtel is a telegram sender receiver analyzer program used to analyze EnOcean serial and radio communication LPC 2 EO1 module must be connected to the LPC 2 configuration and powered Set the DIP Switch on LPC 2 EO1 module to lt SW1 Off SW2 Off gt EnOcean TCM320 Connection mode Connect the PMC see Smarteh products serial cable between RS232 PC port and RJ connector on LPC 2 EO1 In EnOcean WinEtel SW select the correct serial port and press Connect button After successful connection all receive and transmit EnOcean devices data will be logged Please read WinEtel help topics for detailed instructions about working with program When EnOcean device changes its state value etc the relevant data is sent to the EnOcean wireless network Setting up devices definition data into LPC 2 EO1 module All needed data that is used for setting EnOcean device definition in LPC 2 EO1 module is listed in WinEtel log window Detailed description of the data are described in EnOcean User Manual example User Manual TCM3xy Vx xx pdf For devi
5. Rx ec Data receive input COM 6 N C Not connected Table 5 LEDs LED1 Green LPC 2 EO1 status Off No power supply On OK Green EnOcean Rx packet LEDA status On Receiving Rx packet Red EnOcean Tx packet FEDS status On Transmitting Tx packet Table 6 DIP SWITCH SW1 LPC 2 EO1 mode selection Refer to Figure 2 connection scheme DIP switch table SW2 LPC 2 EO1 mode selection Refer to Figure 2 connection scheme DIP switch table mas Longo programmable controller LPC 2 EO1 EnOcean module SMARJIFEH LIVING SYSTEMS 3 2 Mounting instructions Figure 3 Housing dimensions lt Dimensions in millimetres done while module is not connected to the main power supply Any barrier between EnOcean devices and LPC 2 E01 module weakens the reception quality of wireless signal Mounting instructions T All connections module attachments and assembling must be 1 Switch OFF main power supply 2 Mount LPC 2 EO1 module to the provided place inside an electrical panel DIN EN50022 35 rail mounting 3 Mount other LPC 2 modules if required Mount each module to the DIN rail first then attach modules together through K1 and K2 connectors Switch ON main power supply Green LED1 should turn on To set define the communication with EnOcean devices the setup parameter procedure must be execute See APPENDIX for d
6. aa AA 1 2 FEATURES kasir atarap an ka GG AA AA AA AA 2 3 INSTALLATION asian aana aaa aa ag a SANGAN AA Ga aaa ka aaa Sg AGA GK 3 3 1 Connection scheme kampi pina Ghana 3 3 2 Mounting Instructions namam AA AA KA KANINA 5 3 3 Module lab linhgas sasaran a a ngagagi a aaa aan BG aa aa ma Ka Da EE Gg ga aa 6 4 TECHNICAL SPECIFICATIONS ANNA anana anana aana NAA 7 5 APPENDIX SETUP PARAMETER PROCEDURE 1 a aaa 8 CHANGES a NAG AA AA a a d ee ehe aane aa aja 12 NO TES AAP 13 3 mas LONgO programmable controller LPC 2 EO1 EnOcean module SMARJIFEH LIVING SYSTEMS 1 DESCRIPTION LPC 2 EO1 is an EnOcean wireless transceiver module used for wireless communication with EnOcean http www enocean com miniaturized energy harvesting modules LPC 2 EO1 module is based on EnOcean TCM320 transceiver module with integrated whip antenna please refer to User Manual TCM3xy Vx xx pdf for detail information LPC 2 EO1 module can support up to 5 input EnOcean devices like rocker switches occupancy sensors temperature sensors etc and up to 5 output EnOcean devices like switching receivers light dimmer receivers etc please refer to EnOcean equipment profiles x x pdf for detail information On the same way LPC 2 EO1 can communicate and transfer the data between each other and thus establish wireless connection between the LPC 2 controllers EnOcean WinEte telegram sender receiver analyzer program is used to analyze EnOce
7. an serial and radio communication traffic WinEte software is also used to determine the EnOcean devices needed to set up LPC 2 EO1 module 5 0 ms Longo programmable controller LPC 2 E01 EnOcean module SMARJIFEH LIVING SYSTEMS 2 FEATURES Figure 1 LPC 2 EO1 EnOcean module Table 1 Technical data EnOcean transceiver module based on EnOcean TCM320 module with integrated whip antenna Up to 5 receiver and 5 transmitter EnOcean devices supported 868 MHz or 315 MHz EnOcean radio standard Typical working range inside buildings is up to 30m Standard DIN EN50022 35 rail mounting 1 For different EnOcean radio standard frequencies please check LPC 2 EO1 module part number P N 0 ms Longo programmable controller LPC 2 EO1 EnOcean module SMARJIFEH LIVING SYSTEMS 3 INSTALLATION 3 1 Connection scheme example Figure 2 Connection scheme example LED2 LED3 DIP Lt a1 TABLE EnOcean TCM320 Connection LPC 2 EO1 Module Connection Normal Operation Table 2 Kl Internal BUS Data amp DC power supply Connection to I O module Table 3 K2 Internal BUS Data amp DC power supply Connection to I O module o 5 Ee 5 g Longo programmable controller LPC 2 EO1 EnOcean module SMARJIFEH Table 4 K3 LIVING SYSTEMS COM 1 N C Not connected COM 2 GND Ground COM 3 N C Not connected COM 4 RS232 TX 2 3 Data send output COM 5 RS232
8. ce definition in LPC 2 EO1 module following data and parameters are used For input devices ID hex example 0x16121 ORG hex example 0x6 The data ORG ID must be defined on target LPC 2 EO1 EnOcean receiving device individually for each receiving channel Inl ID Byte0 In5 ID Byte3 and Out1 ORG Out5 ORG as confirmed device from which it is receiving data from For output devices ORG hex example 0x30 The data ORG must be defined on corresponding LPC 2 EO1 EnOcean transmitting device individually for each transmitting channel Out1 ORG Out5 ORG agl Longo programmable controller LPC 2 EO1 EnOcean module SMARJIFEH LIVING SYSTEMS To define target EnOcean device for receiving data from LPC 2 EO1 module with its unique ID use earn mode procedure as described in relevant receiving EnOcean device user manual To set or write this device definition parameters into LPC 2 EO1 following steps must be done press disconnect button in WinEtel window set the DIP Switch on LPC 2 EO1 module to lt SW1 On SW2 Off gt LPC 2 EO1 Module Connection mode start the LPC Tester Load xm buffer CTRL amp Shift F11 and select LPC2_EO1 xmI file with parameter descriptions press Start button to establish on line communication with LPC 2 EO1 module In Buffer selector drop list select the relevant EEPROMs for devices parameters mask definition EEPROM1 EEPROMS for setting the parameters mask
9. ee 3 g Longo programmable controller LPC 2 EO1 EnOcean module SMART EH LIVING SYSTEMS CHANGES The following table describes all the changes to the document Date V Description 1 7 2012 003 CGP General update 28 10 2011 002 Updated chapter Setup PARAMETER PROCEDURE 25 5 2010 001 The initial version issued as LPC 2 EO1 EnOcean module UserManual 12 0 ms Longo programmable controller LPC 2 EO1 EnOcean module SMARTIFEH LIVING SYSTEMS NOTES
10. ei 6 SMARTFEH LIVING SYSTEMS USER MANUAL Longo programmable controller LPC 2 EO1 EnOcean module Version 3 SMARTEH d 0 0 Trg tigrovcev 1 5220 Tolmin Slovenia Tel 386 0 388 44 00 e mail info smarteh si www smarteh si g ms Longo programmable controller LPC 2 E01 EnOcean module SMARJIFEH LIVING SYSTEMS Written by SMARTEH d o o Copyright 2010 SMARTEH d o o User Manual Document Version 003 July 1 2012 mms Longo programmable controller LPC 2 EO1 EnOcean module SMARTEH LIVING SYSTEMS STANDARDS AND PROVISIONS Standards recommendations regulations and provisions of the country in which the devices will operate must be considered while planning and setting up electrical devices Work on 230 VAC network is allowed for authorized personnel only DANGER WARNINGS Devices or modules must be protected from moisture dirt and damage during transport storing and operation WARRANTY CONDITIONS For all modules LONGO LPC 2 if no modifications are performed upon and are correctly connected by authorized personnel in consideration of maximum allowed connecting power we offer warranty for 24 months from date of sale to end buyer In case of claims within warranty time which are based on material malfunctions the producer offers free replacement The method of return of malfunctioned module together with description can be arranged with our authorized representative Warranty
11. escription Dismount in reverse order For mounting dismounting modules to from DIN rail a free space of at least one module must be left on the DIN rail NOTE LPC 2 MCU main control module should be powered separately from other electrical appliance connected to LPC 2 system Signal wires must be installed separately from power and high voltage wires in accordance with general industry electrical installation standard Ee g Longo programmable controller LPC 2 EO1 EnOcean module SMARJIFEH LIVING SYSTEMS 3 3 Module labeling Figure 4 Labels on housing Label 1 LPC 2 EO1 module sample Label 2 LPC 2 EO1 module sample LPC 2 EO1 P N 225E0110001001 SIN EO1 S9 1000000190 D C 21 10 Label 1 description 1 LPC 2 EO1 is the full product name 2 P N 225EO110001001 is the part number 225 general code for LPC 2 product family EO1 short product name 10001 sequence code e 10 year of code opening e 001 derivation code 001 version code reserved for future HW and or SW firmware upgrades 3 D C 21 10 is the date code 21 week and 10 year of production Label 2 description 1 S N EO1 59 1000000190 is the serial number EO1 short product name S9 user code test procedure e g Smarteh person xxx 1000000190 year and current stack code e 10 year last two cyphers e 00000190 current stack number previous module would have the stack number 0000
12. odule and main control unit on corresponding addresses downloaded into EEPROMs In LPC Tester Buffer selector drop list RAM1 can be selected to read and write corresponding data of defined EnOcean devices Data blocks In devices Data blocks variables there are 4 bytes 2 words for each device that are received or transmitted over EnOcean wireless network 4 received or transmitted bytes are represented by 2 words as following Received Data blocks variables allocation Block 1 In High Data block 1 byte 3 High byte of Block 1 In High word word Data block 1 byte 2 Low byte of Block 1 In High word Block 1 In Low Data block 1 byte 1 High byte of Block 1 In Low word word Data block 1 byte O Low byte of Block 1 In Low word Transmitted Data blocks variables allocation Block 1 Out High Data block 1 byte 3 High byte of Block 1 Out High word word Data block 1 byte 2 Low byte of Block 1 Out High word Block 1 Out Low Data block 1 byte 1 High byte of Block 1 Out Low word word Data block 1 byte 0 Low byte of Block 1 Out Low word 10 SMARTTEH LIVING SYSTEMS mas Longo programmable controller LPC 2 EO1 EnOcean module Meaning of the values corresponds to each device specifications Please check the manufacturers device specification user manual for details Example of EnOcean switch device Block 1 In High Ox 0 Ox
13. of 1 to 5 devices that LPC 2 EO1 module will transmit data blocks to Example setting for output Data block 1 parameters in LPC Tester EEPROM 1 Table 6 Output Data block EEPROM 1 1 Out1 ORG Example of converting of the output Data block 1 parameters in LPC Tester EEPROM1 Source Out1 ORG Winlog Na Hexadecimal 30 Decimal 48 Write down the parameters in command boxes and press Download button to set the parameters into corresponding EEPROM EEPROM6 EEPROM10 for setting the parameters mask of 1 to 5 devices that LPC 2 EO1 module will receive data blocks from Example setting for input Data block 1 parameters in LPC Tester EEPROM6 Table 7 Input Data block EEPROM 6 1 In1 ID Byte3 0 In1 ID Byte2 1 Inl ID Bytel 97 In1 ID Byte0 33 Inl ORG 6 mas Longo programmable controller LPC 2 E01 EnOcean module SMARTEH LIVING SYSTEMS The source ID data must be converted into decimal split values and write under 4 command fields Example of converting of the input Data block 1 parameters in LPC Tester EEPROM6 Source Inl ID Byte0 Winlog Ox 16121 Hexadecimal 00 01 61 21 Decimal 0 1 97 33 Source In1 ORG Winlog 0x6 Hexadecimal 06 Decimal 6 Write down the parameters in command boxes and press Download button to set the parameters into corresponding EEPROM Data of devices are transferred between LPC 2 EO1 m
Download Pdf Manuals
Related Search