Link - IQBoard
Contents
1. Ltd EVA Pad Wall Anchor Ss Flat Cross tapping Screw Note L Horizontal distance between 2 upper bottom brackets H1 Distance between the 2 screws on the same bottom bracket H2 Distance between the screw on the upper bracket and the upper screw on the bottom bracket Note Please measure L H1 and H2 according to your own IQBoard size otep 3 Put EVA pad into the inside of L type bracket Note One EVA Pad for eac 7 Returnstar Interactive Technology Group Co Ltd h of the upper bracket two for each of the lower one Step 4 Drill 6 holes 70mm in depth by a 6mm electric drill on the positions of the 6 screws you determined as per above 2 holes for each of bottom bracket 1 hole for each of upper bracket Step 5 Put a Wall Anchor into each hole and screw the brackets with M4 70 flat cross tapping screw Step 6 Put IQBoard on the fixed 4 L type Brackets and let it centered horizontally Fasten the upside screws and lock the downside screws Chapter 4 How to Connect to Computer and Projector After fixing the whiteboard find a connecting port at the bottom of left corner protector Plug the USB Standard B into the connecting port and plug the USB Standard A into the available USB port of computer as follows External power source Is not required And please connect the proj2. for most of situations Precise orientation 20 points for high definition system 2 When operating and writing on the whiteboard the position of pen or finger doesn t match the position of cursor 1 The relevant location of projector and white has been changed Please re orient the whiteboard 21 Returnstar Interactive Technology Group Co Ltd 2 The projection area has trapezoid distortion please adjust the projection area and re orient the whiteboard 3 When orienting the whiteboard the pen or finger is not perpendicular to the surface please re orient with correct posture 4 When orienting the whiteboard the pen or finger tip missed the green center of the red orienting cross please re orient the whiteboard 5 The filters around whiteboard have been shaded by other objects such as dust or chalk dust and so on Please keep filters clean When operate and write on the whiteboard the system response is slow or the stroke 15 intermittent 1 The computer is not under normal running or the memory is occupied too much Please close some applications or restart the computer 2 The operating or writing force is uneven Sometimes the force is too light to be sensed 3 Initializing hardware failed Please reconnect the cable with the board to initialize the hardware again 4 When I operate and write on the IQBoard DVTQ the system doesn t respond Please reconnect the cable with the board to initialize t
3. tip Activate IQ Interactive Education Platform If IQ Interactive Education Platform hasn t been activated you can press interactive whiteboard with your palm to activate IQ Interactive Education Platform 15 Returnstar Interactive Technology Group Co Ltd 7 2 How to Use Hotkeys on Whiteboard Add Pape Save File Previous Page bre M Poke hay indicaron or SOM nes fash cup Lee om Io aen Hert Pare Fouse Black Pen Red Pen Blue Pen Green Pen Eraser Tools Applications Following is the introduction of above soft hotkeys Add In Windows Mode press this key to clear all annotations on screen In Board Mode Press this key to add a new page in current cdf file Save File In Windows Mode press this key to save all annotations on screen to a page in current file In Board Mode press this key to save the current cdf file Previous Press this key to go to the previous page Next Page Press this key to go to the next page Mouse Press this key you can use pen finger to achieve click double click and drag function When using Software press this key to switch between Windows Mode and Board Mode Pen 1 There are four Pen keys in different colors on the hotkey bar Press one of these keys you can write on the board in corresponding color Press tw
4. to 15m 2 5 System Requirements Windows XP 2003 Vista 7 8 8 1 10 Intel C2 1 CPU or higher 256 MB RAM or above 1G free hard disk space for full installation 1 free USB port 1 projector short throw or ultra short throw projector recommended Returnstar Interactive Technology Group Co Ltd Chapter 3 How to Install IQBoard Installaton ways of wall mounting mobile stand mounting lifting rail cabinet are available This guide is to introduce L Type Wall Mounting only Other installaion ways please refer to corresponding installation user guide 3 1 Wall Mounting L type Bracket Parts list D x Flat Cross tapping Screw B IQBoard L type Bracket otep 1 Determine the fixed position and height of the IQBoard according to the actual use of the site Installation steps otep 2 Determine the installation height of the bottom L type Brackets according to the location of IQBoard on the wall Then determine the installation height of the upper L type Brackets according to the size of your IQBoard Make sure when you pull up the upper brackets IQBoard can be taken out and when you pull them down IQBoard frame can be clasped Two upper bottom brackets should be on the same height level You will need 2 screws for each of bottom Brackets and 1 screw for each of the upper ones To determine the position of brackets take an 82 IQBoard for e g as below IQBoard H1 mm H2 mm Returnstar Interactive Technology Group Co
5. AND PROJECTOR cccccccccccccccccccccccccccccccccccccccccccccccccccecccccceces 8 CHAPTER 5 HOW INSTALL AND UNINSTALL DRIVER cccccccceccccccccccccccccccccccccccccccccccccccecccs 10 TO INSTALL DRIVER Co dp x du testae dedu a emer D wale LA lotte E 10 5 2 HOW TO UNINSTALE DRIVER canc eae ase a eliew ae eta eed deas oda diea 10 CHAPTER 6 HOW TO SETUP IQBOARD cccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccecccs 11 6 1 ORIENTATION Mt 11 622 HOTKEY SETTINGS enatis usua tendi vni dx Va dama Len Kee d Mars d 13 CHAPTER 7 HOW TO USE NO BOARD ERR VENKE RR NER TERRE TERVERK SR ERR CA DERE USEEER TERR TERVERE EIE ERES 15 BASIC eeu reo o PET ove erepta uc a ades ep deett Rud a e i nt talus Oda te 15 7 2 How TO USE HOTKEYS ON WHITEBOARD ccccececcccecccceccccececcecsccececeececeececeeceaeeceaeeceeeceeeceueess 16 7 3 HOW TO USE TOUCH RECOGNITION 1 1 e cetus eate ce sna beue one ex voe NH ER Er E ed 17 743 1 Enable Touch Recognition eo s E Ot ees 17 7 3 2 Customize Touch Recognition Sensitivity 18 7 35 3 BASIC ODCLALIONS o oit iQ anda D iid Nd iU NRI Id aM DD DIM 19 TA MULDTIFUSERAMWRITING eite oer eus Deben due
6. Drivers then press the Change Remove button to remove the driver 10 Returnstar Interactive Technology Group Co Ltd Chapter 6 How to Setup 6 1 Orientation At the first time you use IQBoard you need to orient it so the moving track of the pen finger can match the cursor You can select 4 points 9 points or 20 points orientation Normally 9 points orientation is adopted After the whiteboard is oriented you don t need to re orient under the same environment To orient the whiteboard Please do as following steps when you orient the whiteboard Step 1 Select Start gt Programs gt IQBoard DVTQ Drivers gt Orient or press on the hotkey bar if your whiteboard is with hotkeys Then the Orientation Points oelection window appears as follow IgBoard DVIQ Drivers Fast 4 points Standard B pointe Precise 20 points Step 2 Select one of the Orientation Points and click OK the Orientation interface appears as follow 11 Returnstar Interactive Technology Group Co Ltd Step 3 Follow the on screen instructions press the center of each cross accurately with the pen or finger tip A Prompt window will pop up as follow after calibration If there s no deviation please click OK Then you can normally operate the interactive whiteboard with colorless writing pen or finger 2 Calibration has been completed If there is still deviation please calibrate agai
7. Returnstar Interactive Technology Group Co Ltd IQBoard DVTQ V1 0 Digital Vision Touch Interactive Whiteboard User Manual PIs E aJ Returnstar Interactive Copyright C 2003 2015 Returnstarlnteractive Technology Group Co Ltd Add 6th Building Pioneer Park Fuzhou High technology Base Shangjie Town Minhou County Fuzhou China Tel 0086 591 38202660 Fax 0086 591 38203003 Web http www iqboard net Returnstar Interactive Technology Group Co Ltd Statement This manual is for IQBoard DVTQ V1 0 Use this product strictly according to detailed operation instruction in this manual so as to ensure proper use Please read this manual carefully before you install this product Opening the package means you have agreed to purchase this product Returnstar will not accept returns of opened packages The product specification may be subject to change without prior notice The sample pictures in this User Manual may differ from the real product Returnstar reserves all rights to charge the fee at anytime for product replacement revision and update The information in this manual is subject to regular change without prior notice Returnstar will make no warranties with respect to this product and disclaims any warranties whether express or implied of merchantability and fitness for a particular purpose Trademark Notice Returnstar and are registered trademarks of Returnstar Interactive Technology G
8. and aside when you turn back to face the students Please do not look at the projector directly to avoid its strong light damaging your eyesight Instruct students how to use the whiteboard tell them not to face the projector directly 9 4 Transport Please handle with care and do not put any weight on the surface so as to avoid the surface distortion and damage Lay the whiteboard upright during the transportation or storage For long distant transportation it is suggested to repack the whiteboard with the original packing If the original packing is unavailable insert some protective padding between the components to protect them from intense vibration or crash Please avoid vibration dampness electricity water and pressure in transportation 9 5 Part Replacement Please do not disassemble the whiteboard or modify its inner structure so as to prevent accident or trouble For maintenance or part replacement please resort to our authorized technician Make sure that you use our designated part or the one with the same specification when replacing 25
9. ctics analysis weather analysis etc IQBoard DVTQ is provided with powerful IQ Interactive Education Platform which makes your operation on interactive whiteboard more convenient Through IQ Interactive Education Platform various interactive teaching and demonstrating functions can be achieved such as write erase label in character line dimension and angle drag zoom reveal screen spotlight screen capture and save screen record and playback handwriting recognition on screen keyboard text input text to speech hyperlink to video sound and webpage and remote conference by NetMeeting IQ Interactive Education Platform also has colorful object animation effects page switching effects and interactive questions Therefore with IQ Interactive Education Platform users can make more interactive courseware by designing unique object animation adding sound or hyper linking IQ Interactive Education Platform also includes 500M IQBoard Resource Library covering more than 30 subjects such as math physics chemistry biology gymnasium etc User can customize the installation by selecting subjects The software also provide common line shape character symbol decoration graph background template Flash courseware and other resources Moreover the software supports importing various picture files and DOC X PPT X XLS X PDF files The page and file created by IQ Interactive Education Platform can be saved as and freely converted to
10. d please do not put the additional weight or pressure on the whiteboard Please keep the whiteboard away from intense collision shaking pressing and do not install it by force otherwise it may cause cracking short circuit and surface distortion Please do not use and install interactive whiteboard in dusty foggy wet and inclement environment Keep it away from sharp object heat source corrosive chemicals fire and water Please do not put the whiteboard in the outlet of hot air otherwise the material will deteriorate and its life span will be shortened 24 Returnstar Interactive Technology Group Co Ltd To avoid harm from improper operation please do not use chair or other tool to help short students use the whiteboard If students are not tall enough to use the whiteboard please low down the whiteboard under the help of the professional technician 9 2 USB Cable Do not put the USB cables on the floor where people might stumble over them If you have to do so straighten them and use insulated adhesive tape or cable with contrast color to tie them up Please don t bend the USB cable excessively Exposing the USB cable outside for long time may shorten its life span and cause other unnecessary damages so please keep it carefully If you use the whiteboard in the meeting room or classroom please fix the cable along the cable alley 9 3 Projection Face the whiteboard when operating and writing on the projected image st
11. e shut down the computer and switch the projector into standby mode to make the dirt more obvious In case of normal dirt soray some water or detergent on the surface then use the paper to wipe the dirt out If you leave some ink trail by mistakenly using the fountain pen please buy some special whiteboard detergent and spray it on the soft cloth to clean the surface For cleaning the mark left by the permanent marker first paint some ink of dry erase marker on the mark the ink of dry erase marker can dissolve the ink of permanent marker then use soft cloth to clean If the mark still exists soay some whiteboard detergent and clean it out Note Please do not use other organic solvent for cleaning Otherwise it may permanently damage the surface For the interactive whiteboard that supports normal marker you can use normal whiteboard eraser and wet cloth to clean E Note Clean the frequently used whiteboard once a week to keep the best definition Please do not use sharp or pointed objects to scratch the surface and frame otherwise the scratched part may be damaged and won t work normally During the usage do not knock or press the surface fiercely with your pen wand or finger to avoid the damage of whiteboard surface pen and wand You can use sand wax to eliminate the scratch on the surface and use dry cloth to clean out Since the mobile stand or the wall hanging parts is designed only to support the weight of the whiteboar
12. ector into the VGA port of your PC video card USB Standard A Plug for connecting the USB Standard B Plug for connecting computer whiteboard Start the projector after connection and adjust it to make its projection within the active area and centered Then use the trapezoid rectification function of the projector to make the projection quadrate Returnstar Interactive Technology Group Co Ltd The blue areas are the maximum projection areas For whiteboards without hotkey there should be 1cm margin between projection area and whiteboard inner frame For whiteboards with soft hotkeys the projection area should not exceed the hotkeys Note 1 In case you use 16 9 whiteboard please choose the projector supporting the 16 9 projection mode 2 The projection image must be within the active area of the whiteboard otherwise the whiteboard cannot work normally Returnstar Interactive Technology Group Co Ltd Chapter 5 How to Install and Uninstall Driver 5 1 How to Install Driver Run IQBoard DVTQ Drivers V1 0 exe in the installation CD and install the drivers according to the prompt The computer will automatically find a new hardware and install the driver 5 2 How to Uninstall Driver Select Start gt Programs gt IQBoard DVTQ Drivers gt Uninstall to uninstall You also can open Control Panel select Add Remove Programs and in the list of currently installed Programs select QBoard DVTQ
13. he hardware again 5 What if part of area in DVTQ can not work or write 1 Hardware initialization failed Please reconnect USB cable and try again when hardware initialization is finished 2 Make sure that you do not touch the board when the hardware initialization is processing If you touch the board it will cause this problem Please reconnect the USB cable or restart computer then try to operate or write on the board after hardware Initialization is finished 6 The pen tip worn out Common abrasion will not affect normal operation When the pen point is severely abraded you can purchase it from local dealer 22 Returnstar Interactive Technology Group Co Ltd 7 When interactive whiteboard is connected and start IQ Interactive Education Platform it is still not registered 1 The driver has not been installed or not been installed successfully please reinstall IQBoard DVTQ Drivers 2 Wrong USB cable connection Use the USB cable in standard configuration and try to operate after the whiteboard hardware is successfully connected For other questions please consult our service center or local dealer 23 Returnstar Interactive Technology Group Co Ltd Chapter 9 Cautions and Maintenance 9 1 Whiteboard For the interactive whiteboard that do not support normal marker no W included in the product model please try not to use normal marker to write on the surface Before cleaning pleas
14. he indication on screen click relevant hotkey in sequence After the setting is completed you can use these hotkeys 13 Returnstar Interactive Technology Group Co Ltd Press ESC tio endi aai F cow mao pkn on ck ness Panian cap 10 aan fanchon Note When setting the soft hotkeys if some error occurs you can press ESC key on the keyboard to exit the setting process and then reset the hotkeys 14 Returnstar Interactive Technology Group Co Ltd Chapter 7 How to Use 7 1 Basic Operations For IQBoard DVTQ you can use the enclosed pen or your finger to write or perform Mouse function Following are the tips for some basic operations Single click If you use pen or finger press the surface with the pen or finger tip at proper strength Double click If you use pen or finger press the surface twice with the pen or finger tip at proper strength Please make sure you press at the same point Right click If you use pen or finger press the surface with the pen or finger tip and hold for 2 seconds to popup the right click menu Drag If you use pen or finger press an object with the pen or finger tip and hold then move the pen or finger tip to drag the object to the desired position Write If you use pen or finger start IQ Interactive Education Platform select a drawing tool then you can write or draw by pressing the surface with the pen or finger
15. ice to modify its properties Eraser Press this key you can erase the writing content on the board In Windows Mode press this key twice to popup the Shut Down Windows window Tools gt Press this key to popup quick access bar including shortcut icons for frequently used tools in IQBoard Software You can add up to 8 shortcut icons in this bar 16 Returnstar Interactive Technology Group Co Ltd Applications Press this key to popup a quick access bar including shortcut icons for frequently used applications You can add up to 8 shortcut icons in this bar Start 1 Press this key to start the Software Orient Press this key to popup the 9 points orientation interface Note 1 Except the Start and Orient keys all hotkeys are functional only after IQBoard Software is started 2 The functions of Frequently Used Tools Frequently Used Applications Orient can be opened or closed by press the relevant hotkeys on the hotkey bar 3 When at Split screen status in Dual user Mode the left hotkeys are for Teacher Pen and the right for Student Pen Teacher Pen can use the hotkeys including Mouse 4 Freehand Drawing Tools Eraser Frequently Used Tools Frequently Used Applications and Orient Student Pen can use the hotkeys including Mouse 4 Freehand Drawing Tools Eraser Frequently Used Tools and Frequently Used Applications If it s not Split screen status in Dual user Mode no differe
16. le ee tpe eei en deutet ub rale aree o a o dta tt bel utut 20 CHAPTERS FAQ Sees e RUE uve oa etos uad d 21 CHAPTER 9 CAUTIONS AND MAINTENANCE cccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccecccs 24 eC H 24 9 2 USB CABLE treo Gagan EPUM EePe nU EU LEID DLE CLER p DA D Lee 25 XS PROJECTION TER Im 25 TRANSPORT TT 25 9 5 PART REPEACEMENT Dee pet 25 Returnstar Interactive Technology Group Co Ltd Chapter 1 Product Introduction IQBoard DVTQ is the latest interactive presentation boards Connect IQBoard DVTQ with your computer and projector then simply touch the projection area with your pen or your finger you can transform the pen or your finger to Mouse and directly operate the computer on the projection area With IQ Interactive Education Platform Multi users can operate simultaneously on the board With IQBoard DVTQ and IQ Interactive Education Platform marvelous interactive communicating effects can be achieved in live demonstration teaching product exhibition business conference video communication news broadcast securities evaluation military command entertainment medical consultation engineering design competition ta
17. m If the whiteboard misinterprets your intent adjust the sliders as detailed above Step Click OK to save your settings To reset Touch Recognition s sensitivity to default settings click Reset to Default 7 3 3 Basic Operations Single Double click Simply click the active area with the pen or finger tip quickly and make sure click at the same point Right click When the left click is on press the whiteboard area for 2 seconds with your pen or finger to activate the right click Activate IQ Interactive Education Platform Tap with five fingers or your palm to activate IQ Interactive Education Platform When in Board Playing Windows and Reviewing Modes Tap with one finger to achieve Freehand Drawing Tools Mouse function Tap with two fingers to imitate functions of Mouse Eraser Tap with your palm to enable function of Eraser 19 Returnstar Interactive Technology Group Co Ltd Note 1 When you want to erase content we recommend you pressing interactive whiteboard with your palm When you want to perform mouse function we recommend you pressing interactive whiteboard with two fingers closed 2 Freehand Drawing Tool and Eraser are Pencil and Normal Eraser by default If you have selected other Freehand Drawing Tool or Eraser before IQBoard Software will use your previous selections 7 4 Multi user Writing Before use Multi user Mode please make sure 1 The operation system you are u
18. n or right click the drive icon in the task bar select the appropriate notebook screen ratio otep 4 If there s still deviation after calibration which usually happen on win8 10 you 0 can click the driver icon on the lower right corner of Task Bar and then select the corresponding screen ration the positioning accuracy can be restored normally 4 3 16 9 16 10 E Reset to default Exit M RSBoardDVTQ 11 03 M ys 2 0 1 If you did not locate the accurate central point or clicked the wrong point or the next fixed point appeared without press please press ESC on the keyboard to exit this orientation and re orient Otherwise you can t operate the whiteboard accurately 2 Please make your pen finger upright when orienting 3 In case the relative position of the whiteboard and projector is changed or the driver or the monitor resolution is altered please re orient 17 Returnstar Interactive Technology Group Co Ltd 6 2 Hotkey Settings If you select interactive whiteboard with soft hotkeys at the first time you use the whiteboard you need to set these hotkeys Step 1 Select Start gt Programs gt IQBoard DVTQ Drivers gt Soft Hotkey Settings to enter the setting window as follow Press ESC to exit V 1 L 4 Prompt Follow the indication on screen dick relevant hotkey on whiteboard in sequence to assign function otep 2 Follow t
19. nce between left and right hotkeys 7 3 How to Use Touch Recognition 7 3 1 Enable Touch Recognition The default setting of touch recognition is off If you want to enable it please select Start gt Programs gt DVTQ Drivers gt Touch Recognition Settings and then select the Enable Touch Recognition check box 17 Returnstar Interactive Technology Group Co Ltd Touch Kecognition Settings Enable Touch Recognition Testing 4rea Touch Recognition Settings Pen 0 31 Mouse 31 95 Eraser 93 160 Clear Eraser 7 3 2 Customize Touch Recognition Sensitivity If the whiteboard often misinterprets your intent while using Touch Recognition function you can customize its sensitivity to suit your style as follow otep 1 Every time you touch the whiteboard with your pen finger or palm the whiteboard acquires a value based on which one of the 3 functions will be performed Write Select and Erase Move the 2 sliders to change the value range for these 3 functions The wider the value range the easier you can perform the related function LE Touch Recognition Settings Enable Touch Recognition Testing Area Touch Recognition Settings Pen 0 31 Mouse 31 93 Eraser 93 16 Reset to default 18 Returnstar Interactive Technology Group Co Ltd Step 2 Test the sensitivity of Touch Recognition by pressing the testing area with pen finger and pal
20. roup Co Ltd Windows is a registered trademark of Microsoft Corporation Recycling Always return your used electronic products batteries and packaging materials to separate collection This way you help prevent uncontrolled waste disposal and promote the recycling of materials Temperature and Humidity Requirements Storage Temperature 40 C 60 C Humidity 0 95 Operation Temperature 20 C 50 C Humidity 15 85 Returnstar Interactive Technology Group Co Ltd CHAPTER 1 PRODUCT INTRODUCTION ccccccecccccccccccccccccccceccccccccccccccccccccccccecccccccccccccecccccceces 4 CHAPTER 2 SPECIFIGATIONS Ven ER A PRAES Ea uen vues Ca a DR E NR SER IER Ra OVER NIS 5 Z ELPERFORMANCE m 5 2 2 FLEXIBLE FIXING AND RELOCATING METHODS ee eene meses ese esses esee serene 5 2 3 DURABLE SURFACE SOLID BODY otov OP HY Dre edt Ead uvae br eie Lo sivo eeu ird 5 rd exco depo RT T me HO 5 2 5 SYSTEM REQUIREMENTS cse eie aieo Ere Mace gua to o vu eon ede a dke s c oenk ea o Ee deua Spec EON Cet 5 CHAPTER 3 HOW TO INSTALE IOBORBRRD NE UCER E Fw bx 6 3 1 WALL MOUNTING L TYPE BRACKET c cccsssecccccccccccsseccccccccussscecccccecausseeecccessuauassesceeeesuauesseceeeenaas 6 CHAPTER 4 HOWTOCONNECT TOCOMPUTER
21. sing is WIN7 or WIN8 or WIN10 2 Multi users writing is only available in the Multi user Mode of IQ Interactive Education Platform with your touch hardware The user number depends on your product model 4 Please check IQ Interactive Education Platform User Manual for more details EE To use Multi users Mode 1 Enter into Board Mode or Full Screen Mode in IQ Interactive Education Platform 2 Select a Pen from Drawing Tools toolbar such as Pencil Brush Pen Pen Board Brush Washing Brush and Creative Pen and then multi users can write simultaneously 3 You can rotate or zoom one or several objects selected in the whiteboard page by Gesture Recognition in Windows OS 4 Tick the nertial Movement under System Setting Other Settings the object will speed up automatically according to the moving speed when moving the object Multi user Mode FILI lt cuam DTOR N1 4 m E 20 Returnstar Interactive Technology Group Co Ltd MEM Tips Multi users should use the same pen tool to write in Multi user Mode Gesture Recognition Zoom and Rotate Inertial Movement Select and pull the object to move it forward automatically Chapter 8 FAQ 1 What kind of orientation precision should select It depends on your requirement of orientation time and accuracy You have the following choices Quick orientation 4 points for fast orientation Standard orientation 9 points
22. various picture files as well as DOC X PPT X XLS X PDF html files etc We provide continuous upgrading service for IQ Interactive Education Platform For more information and detailed operation about IQ Interactive Education Platform please refer to IQ Interactive Education Platform User Manual in the installation CD 4 Returnstar Interactive Technology Group Co Ltd Chapter 2 Specifications 2 1 Performance Resolution 3276832768 Signal tracking rate 8m s Signal processing rate 480 dots s Orientation 4 9 or 20 points 2 2 Flexible Fixing and Relocating Methods Fixing methods include wall hanging cabinets and mobile stand Provide optional height adjustable mobile stand for 50 120 inch whiteboards the height can be adjusted from 1 88M to 2 12M Other sizes of board can be customized 2 3 Durable Surface Solid Body The surface adopts dedicated writing film made of DuPont anti abrasive coating It features with anti scratch high luminance high definition easy cleaning can be cleaned by whiteboard detergent or wet cloth and can completely eliminate bright spots The backboard which is resistant to distortion expansion and shrinkage adopts PS board with high density Model supporting normal pen writing is also provided 2 4 PC Connection Connection Way 1 Standard 8 8m USB cable for connecting IQBoard with PC external power is not required Optional USB signal amplifier to extend the USB cable
Download Pdf Manuals
Related Search