B-5360 5MP
Contents
1. 3 Push the card completely until it clicks into place 4 Attach the dome cover to the camera and tighten the three 3 screws How to Remove the Memory Card In case there is a need to remove the card make sure to access the camera Web Configurator to safely unmount the card first see the camera Firmware User s Manual for more information Once unmounted from the firmware push the card to eject it from the slot me ad vidia How to Connect Audio Device The camera comes with an audio jack where an audio input device such as a microphone with a built in amplifier can be connected The audio in jack is covered by a protective cover WARNING Do not remove this protective cover if the audio in jack will not be used to ensure it remains waterproof To connect an audio input device do the following 1 Pull to remove the protective cover 2 Connect the audio input device Audio Input Jack Audio Device NOTE The microphone must have a built in amplifier Connecting an ordinary microphone will distort sounds and will result in inaudible recording 3 Ifthe camera is installed outdoors be sure to wrap the audio connectors with Waterproof Tape can be purchased in hardware stores DISCLAIMER Advidia will not be responsible for camera damage due by water leakage caused by improper waterproofing of cables me advidia How to Adjust the Viewing Orientation2. advidia B 5360 SMP 360 Weather Proof Mini Dome Hardware Manual Me acdvidia Extraordinary Combination Table of Contents Precautions Safety Instructions cccceeeeeeeeeeeeeensesenseeeneseasesensesensesensesensesonses 5 Introduction 6 PAG KAGE COMENTS saosna 6 PNYSICAl DESCIIDUOM sosisini aa a 7 Mounting OPUORNS oissccete cece ceteseeacetaceeasedsencecedesearsesusenasedecesaseresenventesess 9 Installation Procedures 10 Step 1 Prepare for Installation cccsseseeseeeeeeeenseeenseeeneeeens 10 Step 2 Open the Dome Cove Lf ccscceceseeeenseeeneeeenseeenseeeneesens 11 Step 3 Route the CaO Secs ces esc secs ees eee eee 12 Step 4 Install the Camera cccssccesseeensesenseeenseeenseeenseseneesens 13 Step 5 Waterproof the Cable Connection c csssseeeeseeeeeenees 14 Step 6 Connect to Network ccccsceeseeceneecenseeeneeeensenenseseneesens 17 Step 7 Access the Camera Live VieW cssseseseesseeeesesenes 17 Step 8 Close the Dome CoveD ccssscceesecensecenseeensenenseseneesens 18 Other Adjustments and Accessories 19 How to Install Remove the Memory Cat ccsseeeeeeeeeees 19 How to Insert the Memory Card iscessdecsceesaccssnecdeeseneideercsesdcosszecdeasd 19 How to Remove the Memory Card ccccccssseeeseeeeeseeeesseeeesaeeees 19 How to Connect Audio IN Device ssssussssnnnnnnnnnnnnnnnnnnnnnnnnnn
3. 1 Open the dome cover 2 Loosen the three 3 screws securing the lens 3 Turn the lens to adjust the viewing orientation The arrow on the lens indicates the top side orientation 5 Close the dome cover me advidia Extraordinary Combination Accessing the Camera Configure the IP Addresses In order to be able to communicate with the camera from your PC both the camera and the PC have to be within the same network segment In most cases it means that they both should have very similar IP addresses where only the last number of the IP address is different from each other There are 2 different approaches to IP Address management in Local Area Networks by DHCP Server or Manually Using DHCP Server to Assign IP Addresses If you have connected the computer and the camera into the network that has a DHCP server running then you do not need to configure the IP addresses at all both the camera and the PC would request a unique IP address from DHCP server automatically In such case the camera will immediately be ready for the access from the PC The user however might not know the IP address of the camera yet It is necessary to know the IP address of the camera in other to be able to access it by using a Web browser By double clicking with the left mouse on the camera model it is possible to automatically launch the default browser of the PC with the IP address of the target c
4. Validate settings upon exit naif Meee a advidia B 5360 Hardware Manual Extraordinary Combination Manually adjust the IP addresses of multiple cameras If there are more than 1 camera to be used in the same local area network and there is no DHCP server to assign unique IP addresses to each of them all of the cameras would then have the initial IP address of 192 168 0 100 which is not a proper situation for network devices all the IP addresses have to be different from each other The easiest way to assign cameras the IP addresses is by using IP Utility IP Address NetMask 10 10 2 246 255 255 252 0 z Basic Search z Refresh Device Settings Change Network Address Firmware Upgrade Config Backup Config Restore Reset Save amp Reboot eet wi scat I one ooo IP Address MAC Address FW Version Model Serial No Multicast IP Status 10 10 3 160 00 0F 7C 08 35 79 A1D 311 V5 06 01 NB B 31 B 31 000 228 5 6 1 sonore Oe Caa Change Network Address _ Dynamic IP Address Starting IP Address 192 168 O 100 Netmask 255 255 255 0 Gateway 192 168 0 254 With the procedure shown above all the cameras will have unique IP addresses starting from 192 168 0 101 In case there are 20 cameras selected the last one of the cameras would have the IP 192 168 0 120 Later by pressing the Refresh button of the IP Utility you will be able to se
5. player or QuickTime since these are third party softwares The third party has the right to modify their utility any time which might affect the compatibility In such cases please use Internet Explorer browser instead When using Internet Explorer browser the ActiveX control for video stream management will be downloaded from the camera directly the user just has to accept the use of such control when prompted so No other third party utilities are required to be installed in such case a advidia B 5360 Hardware Manual Extraordinary Combination The following examples in this manual are based on Internet Explorer browser in order to cover all functions of the camera Assuming that the camera s IP address is 192 168 0 100 you can access it by opening the Web browser and typing the following address into Web browser s address bar http 192 168 0 100 Upon successful connection to the camera the user interface called Web Configurator would appear together with the login page The HTTP port number was not added behind the IP address since the default HTTP port of the camera is 80 which can be omitted from the address for convenience ee Web Configurator Account Password Language English v Login Reset Before logging in you need to know the factory default Account and Password of the camera Account Admin Password 123456
6. the supplied anchors In this case attach the included drill template on the surface and drill the screw holes R506 00377 000 ee der Drill ioe Drill Hole Drill Template scale 1 1 Drill Hole me ad vidia Extraordinary Combination Step 2 Open the Dome Cover 1 Loosen the three 3 screws using the included hex screwdriver 2 Lift to remove the dome cover NOTE The dome cover is attached to the camera body by a cable do not lift the dome cover abruptly mg advidia Extraordinary Combination Step 3 Route the Cables Determine whether the cable will pass through a hole on the surface or be routed along the Surface If the cable will pass through a hole on the surface 1 Drill the hole for the cable on the surface Drill cable hole within this block Drill Hole Drill Hole Drill Template scale 1 1 Drill Hole 2 Route the cable from the network side through the hole and connect it to the Ethernet port of the camera NOTE If the camera will be installed outdoors or in places where the environmental factors change drastically make sure to waterproof the cable connection see Step 5 Waterproof the Cable Connection on page 145 for instructions 3 Push the cable through the hole on the surface If the cable will be routed along the surface 1 Pull the tab to slide it off from the dome cover 2 Route the camera cable through the gap on the
7. Lights up when the camera is connected to a network we avila Extraordinary Combination B 5360 Hardware Manual Item Description Audio Input Connects to audio input devices such as a microphone with built in amplifier etc See How to Connect Audio Device on page 20 NOTE The microphone must have a built in amplifier Connecting an ordinary microphone will dwarf sounds and will result in inaudible recording Ethernet Port Connects to a network using an Ethernet cable with RJ 45 S ma amaa Nem Reset Button Restores the factory default settings of the camera To reset the camera while the power is on press and hold the Reset Button for at least 5 seconds or until the Blue LED lights up Memory Card Slot Insert a memory card not included into the slot for local recording purposes See How to Install Remove the Memory Card on page 19 for more information NOTE Supports only microSDHC and microSDXC cards a advidia B 5360 Hardware Manual Extraordinary Combination Mounting Options Select the most suitable solution for your installation environment The camera can be mounted by either of the following methods Mount Types Accessories Suitable when mounting the camera directly on walls or ceilings without additional mounting accessories See Installation Procedures on page 10 for more information Gangbox Suitable when mounting the camera on a 4 Round or 4 Octagon Gangbox The u
8. able gland body Make sure the clamping nut is tightly secured and the rubber is squeezed in to avoid water leakage DISCLAIMER Advidia will not be responsible for camera damage caused by water entering the cable connections mg advidia Extraordinary Combination Step 6 Connect to Network Connect the other end of the network cable to a switch or injector Then connect the switch or injector to a network or PC and a power source See Power over Ethernet PoE example connection diagram below Ethernet Cable Data Ethernet Cable Data Power AC Power Source Camera Step 7 Access the Camera Live View See Accessing the Camera on page 223 for more information on how to access the Live View of the camera me ad vidia Step 8 Close the Dome Cover 1 Align cable tab side of the dome cover to the direction of the network cable 2 Tighten the three 3 screws using the supplied hex screwdriver to attach the dome cover 3 Remove the thin film Final installation should look similar to the illustration below me ad vidia Extraordinary Combination Other Adjustments and Accessories How to Install Remove the Memory Card How to Insert the Memory Card 1 Loosen the three 3 screws to remove the dome cover 2 Insert the memory card into the card slot with the metal contacts facing the bottom side of the camera
9. amera filled in the address bar of the browser already If you work with Advidia cameras regularly then there is even a better way to discover the cameras in the network by using The Advidia B Series Camera Finder Utility The IP Utility is a light software tool that can not only discover the cameras but also list lots of valuable information such as IP and MAC addresses serial numbers firmware versions etc and allows quick configuration of multiple devices at the same time The B Series IP Camera Finder Utility can be downloaded for free from the Advidia website With just one click you can launch the IP Utility and there will be an instant report as follows me ad vidia Extraordinary Combination IP Address NetMask 10 10 2 246 255 255 252 0 z Basic Search Refresh Device Settings Change Network Address Firmware Upgrade Config Backup Config Restore Reset Save amp Reboot Totat 4 Account admin Password 123456 Http Port IP Address MAC Address FW Version Model Serial No Multicast IP Status tj 1010 3160 _ _00 0F 7c 08 35 79 _A1D 311 V5 06 01 NB B 31 000_ 228 564 OO O Add Remove Device E s Add Remove You can quickly see the camera model in the list Click on the IP address to automatically launch the default browser of the PC with the IP address of the target camera filled in the address bar of the browser already me advidia Extraordinary Combin
10. ation Using the Default Camera IP Address lf there is no DHCP server in the given network the user may have to assign the IP addresses to both PC and camera manually to make sure they are in the same network segment When the camera is plugged into network and it does not detect any DHCP services it will automatically assign itself a default IP 192 168 0 100 Whereas the default port number would be 80 In order to access that camera the IP address of the PC has to be configured to match the network segment of the camera Manually adjust the IP address of the PC In the following example based on Windows 7 we will configure the IP address to 192 168 0 99 and set Subnet Mask to 255 255 255 0 by using the steps below SE All Control Panel Items Network and Sharing Center Control Panel Home P A A f x View your basic network information and set up connections Organize v Disable this network device Diagnosi F See full ma mc r Change adapter settings A ie el p wi Tac Fics EET IA Change advanced sharing SISO NP PG kira ay Network settings fhis Goenputen Intel R 8 Disable View your active networks Connect or disconnect Status Diagnose jp Network Access type Internet Work network Connections g Local Area Connection Py Bridge Connections Create Shortcut Change your networking settings Delete de Set up a new connection or network Set up a wireless broadband dial up ad
11. camera cover me ad vidia Step 4 Install the Camera 1 If necessary insert a memory card into the memory card slot of the camera See How to Insert the Memory Card on page 19 for more information NOTE Please make sure the screw is flat on the plate a advidia B 5360 Hardware Manual Extraordinary Combination Step 5 Waterproof the Cable Connection When using the RJ 45 Ethernet cable follow the procedures below to waterproof the cable connection 1 Detach the cable grommet as shown below Grommet Body Clamping Nut 4a Sealing Rubber and Claw 2 On the network side cable insert the clamping nut through the Ethernet cable o 3 Insert the sealing rubber and claw through the Ethernet cable a advidia B 5360 Hardware Manual Extraordinary Combination 4 Make sure the bundled rubber ring is completely aligned on the gap on the grommet body 5 Attach the grommet body to the Ethernet port of the camera IMPORTANT Make sure the rubber ring is completely aligned and flat on the grommet body to avoid possible water leakage 6 Connect the RJ 45 connector of the network cable to the Ethernet port of the camera a advidia B 5360 Hardware Manual Extraordinary Combination 7 Insert the sealing rubber and claw into the cable grommet body 8 Attach the clamping nut to the c
12. e the list of cameras with their new IP addresses Please note that it is also possible to change the IP addresses manually by using the Web browser In such case please plug in only one camera at a time and change its IP address by using the Web browser before plugging in the next one This way the Web browser will not be confused about two devices having the same IP address at the same time me advidia traordinary Combination Access the Camera Now that the camera and the PC are both having their unique IP addresses and are under the same network segment it is possible to use the Web browser of the PC to access the camera You can use any of the browsers to access the camera however the full functionality is provided only for Microsoft Internet Explorer The browser functionality comparison Functionality Internet Explorer Other browsers ee E PTZ Conto Capture the snapshot Video overlay based configuration Motion Detection regions Privacy Mask regions All the other configurations When using non Internet Explorer browsers free third party software plug ins must be installed to the PC first to be able to get the live video feed from the camera Required Plug In QuickTime http www apple com quicktime download Other non Internet Explorer Basic VLC Media Player http www videolan org browsers Disclaimer Notice Advidia does not guarantee the compatibility of its cameras with VLC
13. hoc or VPN connection or set up a router or el Rename Properties access point Connect to a network Be ae Connect or reconnect to a wireless wired dial up or VPN network connection 2ce sO HomeGroup Choose homegroup and sharing options Internet Options Access files and printers located on other network computers or change sharing Windows Firewall settings f a Connection Properties yes 3 Connect using amp Intel R 82567LM 3 Gigabit Network Connection Ca x btocol Version 4 TCPAPv4 Properties You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically This connection uses the following items z a Use the following IP address JM Client for Microsoft Networks Z VirtualBox Bridged Networking Driver aos Packet Scheduler 5 File and Printer Sharing for Microsoft Networks IP address Subnet mask Default gateway Obtain DNS server address automatically Link Layer Topology Discovery Responder Use the following DNS server addresses pac Uns Description Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks Preferred DNS server Alternate DNS server F
14. nd found to comply with the limits for Class B Information Technology Equipment according to European Standard EN 55022 and EN 55024 In a domestic environment this product may cause radio interference in which cause the user may be required to take adequate measures me advidia Safety Instructions Cleaning Disconnect this video product from the power supply before cleaning Attachments Do not use attachments not recommended by the video product manufacturer as they may cause hazards Water and Moisture Do not use this video product near water for example near a bathtub washbowl kitchen sink or laundry tub in a wet basement or near a Swimming pool and the like Don t use accessories not recommended by the manufacturer Only install this device in a dry place protected from weather Servicing Do not attempt to service this video product yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel Damage Requiring service Disconnect this video product from the power supply immediately and refer servicing to qualified service personnel under the following conditions 1 When the power supply cord or plug is damaged If liquid has been spilled or objects have fallen into the video product 3 If the video product has been directly exposed to rain or water If the video product does not operate normally by following the opera
15. nnnnnnnn 20 How to Adjust the Viewing Orientation c csccsssessseseseseeeees 21 Accessing the Camera 22 Configure the IP Addresses ssseeeeeeeeeeeeeeeeeeeeeeeeeeeeenenenneeees 22 Using DHCP Server to Assign IP Addresses cceceeeees 22 Using the Default Camera IP Address ccccceceeeeeeeeeseeeeeeeees 24 Access the Camel a scccecececscscsccncecscscscscenencaceceeececeaeaceesaseeeeneaeneeaes 26 me ad vidia Extraordinary Combination Precautions Read these instructions You should read all the safety and operating instructions before using this product Heed all warnings You must adhere to all the warnings on the product and in the instruction manual Failure to follow the safety instruction given may directly endanger people cause damage to the system or to other equipment Servicing Do not attempt to service this video device yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel Trademarks All names used in this manual are probably registered trademarks of respective companies Liability Every reasonable care has been taken during the writing of this manual Please contact Advidia if you find any inaccuracies or omissions We cannot be held responsible for any typographical or technical errors and reserve the right to make changes to the product and manuals without prior n
16. otice a advidia B 5360 Hardware Manual Extraordinary Combination Federal Communications Commission Statement This equipment has been tested and found to comply with the limits for a class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Warning Changes or modifications to the equipment that are not expressly approved by the responsible party for compliance could void the user s authority to operate the equipment European Community Compliance Statement C 4 This product has been tested a
17. se of gangbox is lawfully required in some areas in the United States A Gangbox Converter purchased separately is required for this type of installation Suitable when mounting the camera on the wall with the camera facing down as if installed on the ceiling The Wall Mount optional mounting accessory is required for this type of installation Pendant Mount Suitable when installing the camera on high ceilings where a straight tube is used to lower the camera The Pendant Mount with Mount Kit optional accessory set is required for this type of installation e For more information about the mounting solutions and accessories please check our website e The above mounting accessories are not included in the package Contact your sales agents to purchase me ad vidia Extraordinary Combination Installation Procedures This section describes procedures in mounting the camera on a flat surface NOTE The camera images on this documentation are for reference only and may be different from the actual camera Step 1 Prepare for Installation 1 Before installing the camera prepare the additional accessories required for installation Required Accessories e Exterior grade Ethernet Cable with RJ 45 connector not included in the package e Cable Grommet Included 2 Depending on the material of the mounting surface where the camera will be installed it may be necessary to drill the three 3 screw holes and use
18. ting Instructions in this manual Adjust only those controls that are covered by the instruction manual as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation Safety Check Upon completion of any service or repairs to this video product ask the service technician to perform safety checks to determine if the video product is in proper operating condition me ad vidia Extraordinary Combination Introduction Package Contents Check if the camera package comes with the following items B 5360 Camera Body Screw Kit Drill Template Drill Hole Drill Hole Drill Template scale 1 1 Hexagon Screwdriver Cable Grommet Quick Start Guide Quick Start Guide IMPORTANT When the camera is taken out from the box the lens cover is covered by a protective film DO NOT remove this film It is used to protect the lens cover from scratches or fingerprint marks which may happen during installation Remove this film only after the camera is securely installed and all connections are complete me ad vidia Extraordinary Combination Physical Description Item Description System LEDs Indicates the camera status Amber LED Blinks when network activity is in progress Blue LED Lights up when the camera is powered up and goes off again after the boot up process is complete Green LED
Download Pdf Manuals
Related Search