MultiSpot® HT3030 (HP3)
Contents
1. tate seed oud la RE e aaron 95W m Technical data MULTIWALL GII HT3030 Pa n ls Outp t eee d t ree LT NN VRAT oak iene 1 panel 3550 Im LEDS taten kn 30x3W RGB 3 in 1 30x1W 30x1W green 30x1W blue chip A ertet rebut Secondary 25 degrees Common technical data oor ro ettet et t 3 5 Channels DMX 512 1990 e REN 20 indoor 65 outdoor Mains tite go eR reb eI ERES AC100 250V 50 60Hz Power emere nee neta na sen Switch mode DMX connections en Gasca cess exeun en dte 3 pin XLR Male Female Modulation Pulse Density Modulation PDM Dimensions LxWXH coccion pie 330 0 x327 0 x151 5mm Weight Arne TELS 7 1kg m Standards This product complies with the following standards EU electrical EN60598 1 2008 EN60598 2 1 1989 EU general safety EN60598 2 17 EU photobiological safety EN 62471 2008 EU 55015 2006 1 2007 61547 1995 1 2000 EU H armonies u nenne sen EN61000 3 2 2006 EU Flicker ois nee aces ir cen re ans pere ee ertt De Be nen de Due ara EN61000 3 3 2008 US2. 11 Check whether the front glass seal smoothly surrounds the front glass in proper position and put the front glass back into place properly centering it on the mounting edge around the Lens LED panel 12 Check whether the main seal is properly aligned and smoothly adapts to the groove around the lens LED panel 13 Carefully lower the front frame down on the main unit in the right position with aligned screw holes avoiding any position change of the front glass with seal and the main seal during this procedure 14 Provide clamping of the main unit and the front frame by means of holding them together with both hands and turn the unit around 15 Put the 8 screws back into place which connect the main unit with the front frame and tighten them with 3 0 3 3Nm torque LENS PANEL CHANGE IL Lens Panel Standoff K B Front Frame Lens Panel Screw Lens Panel y 4 Front Glass Y Glass Seal m _ Main Seal A REMOVE FRONT FRAME SCREWS B DISMANTLE FRONT FRAME GLASS C REMOVE CHANGE LENS PANEL A User Manual Multispot Gll HS3045 HT3030 WW MULTIFORM Getting started choosing a location Risk of fire The MULTISPOT GII HS3045 HT3030 LED has been AAN designed for environmental temperatures of up to 40 degrees Celsius For proper operation the unit must be operated with unobstructed air convection to its outside metal case Do not Operate the MULTISPOT GII HS3045 HT3030 LED i
3. OMANDAARWN V2 00 08 2013 15 User Manual Multispot GII HS3045 HT3030 VW MULTIFORM Upon the user s choice the unit can work in stand alone automatic mode or with fixed colors or it may be controlled by external DMX controllers Available modes m STATIC COLOUR Press the MODE button until the display shows STxx whereas xx stands for numbers 0 until 25 Use the left right arrows to change the colour between any of the 26 presets the display shows 570 5725 accordingly and will remain to show unless the dim function is used Use the button to change the dim level The first touch of the or button changes the display now showing the dimming level L0OO L100 representing the relative dimming level chosen Now the dimming level can be changed by using the buttons Pressing the buttons for longer than 1 second accelerates the change rate of the displayed value to 3 times If no further changes are made to the dimming level by the buttons the display will automatically return to show STxx after 5 seconds and the dimming level will remain as last set The same happens if the color preset is changed by the left right arrows in this case the dimming level mode is left immediately and the dimming level will remain as last set Color settings for STO ST25 as follows Preset Color Preset Color STO all off sT13 P
4. the units AC output since being connected by the AC output to other units which are still under AC supply will still supply power to the unit the unit is completely dry and at room temperature the location chosen to exchange the connectors does not have more than 40 relative humidity and the temperature during the exchange does not exceed 40 degrees Celsius These parameters are important to avoid later condensation of the water contained in the environmental air when the unit works at lower outside temperatures the screw driver used to dismantle and re assemble the unit is properly matching the screws to avoid any damage to the screws This will require a 4mm Hexlnsert screw driver the screw driver has an in built torque measurement or you have other torque measurement devices on hand to make sure that screws are fastened with the right torque during re assembly To expedite the connector change you will need Multiform s outdoor conversion kit for this unit which is available from your distributor Further you will also need to have the suitable cable material on hand which ideally is e Rubber AC cable of at least 3x1 5sqmm cross section with outer diameter of not less than 6mm and not more than 9mm e DMX signal cable 2 wire shield with outer diameter of not less than 6mm and not more than 9mm e Matching wire termination sleeves Reliability risk Using cable material of unsuitable outer diameter or AN with insuffici
5. both RGB and HSL color mixing control This fixture can be used in both indoor and outdoor applications USER MANUAL MULTISPOT G I HS3045 HT3030 High Power DMX Controlled LED light source For firmware 50 010 0088 00113 1 01 MS GII RevN AA MULTIFORM Updated versions of this document may be available at WWW MULTIFORM LIGHTING COM RevB 08 2013 Order code 12 010 0083 80201 1 01 User Manual Multispot Gll HS3045 HT3030 VW MULTIFORM Introduction Dear customer congratulations on the purchase of a Multiform branded item and the trust having been put in us with this decision Multiform is one of the leading global manufacturers of professional lighting equipment and has decades of experience in design production and quality assurance To meet your requirements this unit has been designed and built to the highest standards so that we can assure you that you have made a good and satisfying investment To take full advantage of all possibilities and for your own safety and the safety of your environment please read these operating instructions carefully before you start using the unit m Description The MultiSpot GII is a high power DMX controlled LED light source for both indoor and outdoor applications which range from architectural illumination to stage lighting Available in various LED configurations this fixture has been designed for flexibility and reliability which includes various connection options and an advanc
6. over to the authorized service for a security check 8 To meet all aspects of functionality and security during mainte nance work to be preformed on this unit all parts should be replaced by genuine spare parts Consequently take care of your dealer or maintenance company to be authorized by the manufacturer Health advice This unit produces and absorbs electromagnetic radiation The strength of radiation and the sensitivity for disturbing interference matches the CE and FCC requirements A corresponding sign is printed on the backside of the unit Any change or modification may affect the behavior of the unit concerning electromagnetic radiation with the CE requirements eventually not to be met any more The manufacturer takes no responsibility in this case Functional advice This unit is immune to the presence of electromagnetic disturbances both conducted and radiated up to a certain level Under peak conditions the unit is classified to show a class C performance criteria and may encounter temporary degradation or loss of function which may need manual help to recover In such case disconnect the AC power from the unit and reconnect it again to recover Environmental advice This unit is built to conform to the ROHS standards and the WEEE directive 2002 96 EC of the European Parliament and of the Council of the European Union Under these regulations the product shall not be discarded into regular garbage a
7. safety t Ihe sin sh ai UL60065 US EMG ont d een esce aam eo emet usd Pes cdd FCC Part 15 This product meets both the EMC Directive 2004 108 EC and the Low Voltage Directive 2006 95 EC V2 00 08 2013 22 MultiSpot HT3030 HP3 APOLLO DESIGN Apollo Design Technology Inc 260 497 9191 ApolloDesign net Copyright 2015 Apollo Design Technology Inc 11 15
8. 2013 18 User Manual Multispot GII HS3045 HT3030 WW MULTIFORM 5111 1 loop 6 seconds SL24 2 8 loops per second SL12 1 loop per 4 seconds SL25 3 2 loops per second Once the speed level is set and no changes done the display will return to show FPO FP7 after 5 seconds The same happens if the pattern preset is changed by the left right arrows in this case the speed setting mode is left immediately and the speed will remain as last set DMX SLAVE MODE Press the MODE button until the display shows SLA indicating that the unit works in slave mode The unit will receive DMX commands on channels 1 2 and 3 Please note that these 3 channels represent a common communication standard between all models of the Multispot Gll series and do not directly relate to the LED colors The channels carry RGB information which is internally re calculated into the control information required for the specific units LED arrangement Hence it is not recommended to use the SLAVE mode with any external controllers since it has been specifically designed for setups where one Multispot Gll acts as a master and the others as slaves while the different models of the range can be mixed The attempt to use an external DMX controller as a master with all connected Multispot Gll set to SLA mode will deliver unexpected and or confusing results use the GDMX setting instead NOTE Whenever a DMX signal is received t
9. 5 compliant outdoor version with PG9 cable glands to hold all connection cables in a waterproof manner Reliability risk Changing the connectors in an inappropriate manner may defeat the waterproof capabilities of the fixture and may void any warranty of the manufacturer if water intrudes into the unit It is essential to follow the below instructions to maintain the waterproof capabilities of the fixture and its product warranty subsequently Safety risk This procedure requires to open the unit In case of unintended connection to AC supply life parts may be exposed and touchable In case of wrong internal wiring the safety of the whole installation where this unit is used may be endangered and a risk of fire is possible This procedure shall hence only be carried out by qualified technicians with relevant experience in safe work methods for electrical equipment service and maintenance DO NOT attempt to change the connectors by yourself if you do not have the applicable experience The manufacturer does not take any liability for life and assets if such unqualified attempt is made PPP V2 00 08 2013 6 User Manual Multispot Gll HS3045 HT3030 VW MULTIFORM Before you start to change the connectors please make sure that yourself or the person in charge has the relevant experience in safe work methods for electrical equipment service and maintenance the unit is disconnected from any AC source Please note that this also applies to
10. ESET MODE and the display will show YES Press the button to activate a reset to the factory default settings and calibration the button is disabled in this menu For confirmation the LED panel flashes once The reset excludes the operation hours Operation Hours Use the left right arrows until the display shows HOUR Press the button and the display will show the operating hours up to 9999 hours Operating hours exceeding the first 9999 hours can be extracted from the unit via RDM by a qualified service technician FW Version Use the left right arrows until the display shows VERS Press either of the buttons to have the display showing the firmware version Maintenance V2 00 08 2013 21 User Manual Multispot GII HS3045 HT3030 WW MULTIFORM This device does not need regular maintenance lt is protected by an internal fuse located on the power supply PCB If this fuse fails this usually indicates an internal fault requiring servicing by a qualified engineer The fuse shall only be replaced by a fuse of same specification and the replacement has to be made by qualified personnel obeying applicable safety rules m Technical data MULTISPOT GII HS3045 Ranels Output tun ter EE eere ee tent ete 1 panel 3690 Im LEDS per panel sete engeren Y 49x3W 1 chip 15x1W red 18x1W green 12x1W blue Oli E Secondary 25 degrees Power
11. M changed After 30 sec of no alterations or if the MODE button is pressed the display returns to show GDMX IN PRES preset mode the channel assignment is as follows CH1 000 255 Color presets ST1 ST25 as in Static Color Mode If CH3 lt 050 CH1 000 127 Fade presets FPO FP7 as in Switch Pattern Mode If CH3 gt 050 CH1 128 255 Fade presets SPO SP8 as in Fade Pattern Mode If CH3 gt 050 CH2 000 255 Master Dimmer 0 100 CH3 000 049 Color preset mode selection color by CH1 CH3 050 255 Pattern preset mode selection and speed setting pattern by CH1 CH4 000 049 Strobe off 050 255 Strobe with adjustable speed 050 slow 255 max speed NOTE Whenever a DMX signal is received the D tab in the display is lit this is valid for all DMX related modes The DMX channel setting is global if you change the control mode channel scheme later the DMX start address will remain valid but the number of consumed channels may change DO NOT try to leave the control mode channel scheme choice by pressing the left right arrow buttons this would change the control mode channel scheme to the next subsequent choice Always leave this mode by either pressing the MODE button or by simply waiting until the display returns to show GDMX COLOR BALANCE In this Mode you can define your individual fixture s Color Balance by setting a maximum brightness for each LED colour giving you the indiv
12. MultiSpot HT3030 HP3 FS APOLL DESIGN Introduction Since 1992 Apollo Design Technology Inc has been one of the world s leading innovators manufacturers and distributors of gobos color filters lights and related equipment and accessories for the lighting industry We are continually engineering new products to help you create and execute the designs of your dreams for theaters bands advertising touring companies television motion pictures museums retail and architecture Apollo Design is recognized for creating innovative and award winning products of superior quality and value Focused on you our goal is to ensure unparalleled support from the initial conversation to after sales service Our lighting experts and engineers will consult with you on ways to use our standard products or engineer custom solutions Allow your imagination to run free Let the Apollo Design team help you create the lighting design you only imagined There is virtually no limit to what we can do together Mer Joel Nichols Owner CEO Apollo Design Technology Product Description Congratulations on the purchase of your MultiSpot HT3030 Apollo Design is proud to be the exclusive USA distributor The MultiSpot HT3030 formerly known as the HP3 provides medium flood dispersion perfect color mixing at short distances and maximum overall brightness The MultiSpot HT3030 comes with a powerful RGB MulTriLED panel and offers
13. PCB Supply DC Black Lead ACAn Out GND YG Lead Len Supply DC Red Lead LED PCB Supply GND Black Lead B DMX Out GND Black Lead DMX In DATA Red Lead DMX Out DATA Green Lead DMX In DATA Green Lead IDMX Out DATA Red Lead DMX In GND Black Lead Supply OC Red Lead Supply DC Black Lead o DANGER Safety hazard NOTE Risk of severe injury or death Any internal work on this unit shall only be carried out be qualified technicians who are familiar with WARNING Hazardous voltage safe repair techniques Disconnect AC before Risk of lethal or severe electric shock opening the unit V2 00 08 2013 10 User Manual Multispot Gll HS3045 HT3030 WW MULTIFORM m Getting started changing the lens panel only if required only HT3030 Your MULTISPOT GII HS3045 HT3030 has been factory fitted with the default lens panel If you need to exchange the lens panel to achieve specific dispersion angles only HT3030 please contact your distributor for availability information of other lens panels and follow the below procedure to exchange the lens panel if required Reliability risk Exchanging the lens panel in an inappropriate manner AN may defeat the waterproof capabilities of the fixture and may void any warranty of the manufacturer if water intrudes into the unit lt is essential to follow the below instructions to maintain the waterproof capabilities o
14. POT GII HS3045 HT3030 LED has AC outlet that is designed to carry loads of no more than 10A Make sure that all connected devices in a chain fed by the first device do not exceed a maximum of 10A current consumption m Getting started making DMX control connections Connect the MULTISPOT GII HS3045 HT3030 to a suitable DMX controller where needed and interconnect several units by means of their DMX In Outputs as required The last unit shall be fitted with a proper 120 Ohm termination resistor equipped DMX plug as shown in below drawing Please make sure that all used DMX cables comply to below standard DMX output DMX output DMX input DMX input TERMINATION TU JT 4 2 937 2 4 RY WEY WS 5 Pin 3 Pin 5 Pin 3 Pin PIN WIRE SIGNAL 1 SHIELD GROUND RETURN OV 2 INNER CONDUCTOR DATA COMPLEMENT INVERTED 3 INNER CONDUCTOR DATA TRUE NON INVERTED V2 00 08 2013 14 User Manual Multispot Gll HS3045 HT3030 WW MULTIFORM m Operation USER INTERFACE User interface overview MODE selection Button LEFT ARROW Button RIGHT ARROW Button Button Button DISPLAY Sound to Light Indicator DISPLAY 4 Digit Message Display Area DISPLAY Indicator DISPLAY Indicator 10 DISPLAY ARROW Indicators 11 DISPLAY DMX Signal Presence Indicator 12 Microphone cover membrane 13 DMX Input 14 DMX Output 15 AC Power Input 16 AC Power Output 17 M6 safety lug mounting thread 18 M10 nut insert point
15. SL16 2 5 steps per second SL4 1 step per 60 seconds SL17 3 steps per second SL5 1 step per 30 seconds SL18 4 steps per second SL6 1 step per 20 seconds SL19 5 steps per second SL7 1 step per 10 seconds 5120 6 steps per second SL8 1 step per 5 seconds 5121 7 steps per second SL9 1 step per 3 seconds SL22 8 steps per second SL10 1 step per 2 seconds SL23 9 steps per second SL11 1 step per 1 6 seconds SL24 10 steps per second SL12 1 step per 1 2 seconds SL25 11 steps per second V2 00 08 2013 17 User Manual Multispot GII HS3045 HT3030 MM MULTIFORM Please note that above speed levels are only applicable to patterns SPO SP08 For the strobe patterns the following speed table applies Setting Speed S2L Beatflash function one flash per sound trigger Strobe to Sound SL1 SL25 Strobe speed 1 Hz 18Hz Choosing S2L activates the Sound to Light function shown by illuminating the S symbol in the display and displaying S2L The speed is now being driven by the beat of the music taken up by the built in microphone Once the speed level is set or the S2L function chosen and no changes done the display will return to show 5 0 5 12 after 5 seconds The same happens if the pattern preset is changed by the left right arrows in this case the speed setting mode is left immediately and the speed will remain as last set FADE PATTERNS In this mode you will only find sof
16. When mounting the unit to truss be sure to secure an appropriately rated clamp to the hanging yoke using a M10 screw fitted through the center hole of the hanging yoke Where required secure the installation with an appropriate safety cable Always use a certified safety cable according to DIN56927 that can hold 12 times the V2 00 08 2013 13 User Manual Multispot Gll HS3045 HT3030 WW MULTIFORM weight of the device when installing the unit This secondary safety attachment should be installed in a way that no part of the installation can drop more than 20cm if the main attachment fails Never stand directly below the device when mounting removing or servicing the fixture Make sure the area below the installation place is free from unwanted persons during rigging de rigging and servicing The operator has to make sure that the safety relating and machine technical installations are approved by an expert before using them for the first time The installations should be re inspected every year Make sure to comply with applicable cooling requirements if any m Getting started making AC supply connections Risk of fire Safety risk The MULTISPOT GII HS3045 HT3030 LED requires AC power source with sufficient power carriage and correct grounding to ensure safe operation The AC power source must be equipped with a circuit breaker and earth leakage detector Make sure to only use compliant AC supply lines The MULTIS
17. ally happen that the front glass including its rubber seal stick to the front frame and fall out during the removal procedure potentially damaging the front glass 4 Carefully lift off the front glass including the glass seal Illustration step B 5 Unscrew and remove the 5 lens panel screws holding the lens panel 6 Remove the lens panel by vertical lifting it off It is important to expedite this process absolutely perpendicular to the LED panel as excessive tilting of the lens panel versus the LED panel can damage the LEDs Use both hands and the provided finger grip points and lift off the lens panel V2 00 08 2013 11 User Manual Multispot GII HS3045 HT3030 MM MULTIFORM 7 Remove the 5 standoffs that define the lens panel distance to the PCB by unscrewing them with left turns Keep these 5 standoffs stored together with the removed lens panel as every specific lens panel has its matching standoff length 8 Insert the 5 standoffs that have been delivered with the new lens panel into the relative thread holes and fix them properly with right turns 9 Put the new lens panel into place by perpendicularly lowering it down on the LED panel Make sure the LED panel is lowered in the right position as lowering it in the wrong position may lead to collision between the lenses and the LEDs which may damage the LEDs 10 Put the 5 lens panel screws back into place which hold the lens panel and tighten them with 0 50 0 55Nm torque
18. ces and heavy vibration may damage this product mechanically Protection from eye injury 1 Warning Depending on the configuration of the device this device may reach or exceed the limits of EN62471 risk group 2 and may hence reach to risk group 3 To avoid eye injury do not look into the beam from a distance of less than 8 5 m 27 ft 11 ins from the front surface of the fixture without protective eyewear such as shade 5 welding goggles At larger distances light output is harmless to the naked eye provided that the eye s natural aversion response is not affected Do not view the beam directly with optical instruments such as magnifiers telescopes binoculars or similar optical instruments that may concentrate the light output Ensure that during setup and DMX programming no persons are inside a 8 50m 27 ft 11 ins vicinity of the device s front surface to avoid that they may accidently be exposed to the light beam User Manual Multispot Gll HS3045 HT3030 WW MULTIFORM 2 Where the mains plug or an appliance coupler is used as a dis connect device such device shall remain readily operable 3 To pull the AC Cord out of the wall outlet or the units AC socket never pull the cable itself but only the AC plug 4 Disconnect the unit from AC supply before any kind of cleaning on the product Use smooth and dry cloth only for cleaning 5 Do not expose this unit to any dripping or splashing liquids and do not place objec
19. consecutive DMX addresses for individual control or to set all subsequent units to SLAVE mode for mutual control To enable GDMX auto addressing press the button to start the auto addressing process and keep it pressed the display will show GDMX when done To enable SLAVE auto addressing press the button to start the auto addressing process and keep it pressed the display will show SLAVE when done Auto Lock Use the left right arrows until the display shows ALOK Press any of the button to alternate between on or off When on the unit will lock itself after more than 1 minute of no use of the Ul When off the Ul will remain unlocked To unlock a locked unit press the left and the right arrow buttons simultaneously Auto Display off Use the left right arrows until the display shows ADIS Press any of the button to alternate between on or off When on the unit will disable the LCD backlight after more than 1 minute of no use of the Ul When off the display backlight will remain enabled Note The display elements themselves remain active Temperature Display Use the left right arrows until the display shows TEMP Press any of the button to alternate between on or off When on the unit will display the temperature in C after more than 1 minute of no use of the UI Reset Use the left right arrows until the display shows RSET Press the or the button to enter the R
20. each ST1 Red 5714 Aqua ST2 Green ST15 Leaf ST3 Blue ST16 Purple ST4 Yellow ST17 Barbie ST5 Pink ST18 Breeze ST6 Turquoise ST19 White 1 cold ST7 Lime ST20 White 2 ST8 Orange ST21 White 3 ST9 Marine ST22 White 4 ST10 Frog 5723 White 5 warm ST11 Lavender ST24 Light Orange 5712 5725 Dark Orange COLOUR SCROLL Press the MODE button until the display shows Cxxx whereas xxx stands for numbers 000 until 225 A touch of the left right arrow buttons will lead to a change of the Colour Choose your desired colour The display shows 0 225 accordingly and will remain to show unless the dim function is used Use the button to change the dim level The first touch of the or button changes the display now showing the dimming level LO00 L100 representing the relative dimming level chosen Now the dimming level can be changed by using the buttons Pressing the buttons for longer than V2 00 08 2013 16 User Manual Multispot GII HS3045 HT3030 MM MULTIFORM 1 second accelerates the change rate of the displayed value to 3 times If no further changes are made to the dimming level by the buttons the display will automatically return to show 0 225 after 5 seconds and the dimming level will remain as last set The same happens if the color is changed by the left right arrows in this case the dimming level mode is left immediately and the dimming level wi
21. ed cooling system allowing for longer LED lifetime SAFETY INFORMATION Read the safety precautions in this chapter before installing powering up operating or servicing this device Failure to do so may void the product warranty and releases the manufacturer from all product liability gt Symbols used in this manual The following symbols are used to identify important safety information on the product and in this manual WARNING Read manual before installation operation or servicing WARNING Safety hazard Risk of injury or death WARNING Hazardous voltage Risk of severe or fatal electric shock PPP V2 00 08 2013 2 User Manual Multispot GII HS3045 HT3030 MM MULTIFORM WARNING Shock hazard Equipment must be properly grounded WARNING Hot surface Risk of skin burn or skin irritation WARNING Fire hazard WARNING Laser radiation Risk of surface damage WARNING LED light emission Risk of eye injury Security advice before use gt OP ONS V2 00 08 2013 General advice o Read this manual completely before using the product Keep this manual in your records for future reference Follow all instruction printed in this manual Follow all printed security advice on the product itself Take care of enough distance between this product and sources of hum and noise like electric motors and transformers Carry this product with greatest care Punches big for
22. emble the PG9 cable gland body with the outdoor conversion panels Make sure that the lower PG cable gland seal is fitted properly and that the nut which holds the gland in the outdoor conversion panel is tightened sufficiently Do NOT yet fit the upper cover nut and the cable seals 8 Turn the rear cover with the electronics assembly to face its outside Mount the outdoor conversion panels with the pre mounted PG gland bodies to the outside of the rear cover of the fixture using the provided two mid placed fixing screws 9 Put the cover nuts of the PG glands over the cable end and push the cable seals on the cables 10 Insert the cables into the cable gland bodies mounted to the rear cover and loosely fix the cover nuts so that the cable can still be moved longitudinally 11 Turn the rear cover with the electronics assembly to face its inside Pull the cable stumbs far enough out to allow skinning of the leads inside the cables 12 Skin the separate leads of both the DMX and AC cables and terminate them properly with termination sleeves 13 Insert the AC leads into the terminal block of the PSU PCB as indicated on the internal connections chart and fix the terminal block screws accordingly 14 Insert the DMX leads into the terminal blocks on the MCU PCB as indicated on the internal connections chart and fix the terminal block screws accordingly 15 Pull the cables from the outside of the rear cover until the remaining internal length
23. ent flexibility of its outer tubing may defeat the waterproof capabilities of the fixture and may void any warranty The conversion kit itself contains To e outdoor conversion panels 2 The rubber seals for the outdoor conversion panels x2 The PGS cable glands made from stainless steel x4 The Fitting screws to generate sufficient seal pressure x4 The rubber plain washers as seals for the fitting screws x4 The rubber dummy plugs needed if a cable gland remains without cable x3 start expediting the connector change please follow the below step by step instructions and draw your attention to the illustrations provided Please note this refers to a conversion from indoor to outdoor for the inverse conversion please reverse the procedure s steps 5 16 V2 00 08 2013 7 User Manual Multispot GII HS3045 HT3030 MM MULTIFORM 1 Loosen the 6pcs of screw that hold the rear cover of the power supply compartment and remove the screws 2 Carefully lift the rear cover with the attached electronics assembly from the main unit 3 Turn the rear cover around and unplug the wire connections to the main unit 4 Detach the rear cover with the attached electronics assembly from the main unit 5 Unscrew the fitted XLR and PowerCon connectors from the rear cover 6 Unscrew the connector connection cables from the screw terminals on the MCU PCB for DMX and on the PSU PCB for power 7 Pre ass
24. f the fixture and its product warranty subsequently Before you start to exchange the lens panel please make sure that the unit is completely dry and at room temperature the location chosen to exchange the lens panel does not have more than 40 relative humidity and the temperature during the exchange does not exceed 40 degrees Celsius These parameters are important to avoid later condensation of the water contained in the environmental air when the unit works at lower outside temperatures The screw driver used to dismantle and re assemble the unit is properly matching the screws to avoid any damage to the screws This will require a 4mm Hexlnsert screw driver The screw driver has an in built torque measurement or you have other torque measurement devices on hand to make sure that screws are fastened with the right torque during re assembly To exchange the lens panel follow the below procedure 1 Make sure the unit is switched off and cooled down for at least 30 minutes after last operation Detach all cables 2 Lay the unit face down on a stable but soft surface like a table covered with a towel and remove the 8 screws which connect the main fixture body with the front frame Illustration step A 3 Turn the unit around and lift off the front frame while you hold down the front glass Holding down the front glass is a safety precaution since due to the adhesion of the soft rubber of the front glass seal it could potenti
25. he D tab in the display is lit this is valid for all DMX related modes DMX GENERAL MODE ADDRESS SETTING Press the MODE button until the display shows GDMX By the first touch of the left or right arrow button the present DMX Mode will be displayed Use these left right arrow buttons to choose between any of the following color control modes channel schemes 3RAW colors RGB channels colors RGB combined master strobe 4 channels as old Multispot 5 colors RGB master strobe 5 channels HSLS Hue Saturation Lightness strobe 4 channels PRES Presets allows to recall the preset colours and programmes of the unit 4 Channels see assignment specification below Once having chosen the required control mode channel scheme please use the or buttons to set the required DMX address Pressing the or button for the first time will show the present DMX address which then can be altered by repeatedly using the buttons in a range from 001 to 512 The display will show 1 512 accordingly Pressing the buttons for longer than 1 second accelerates the change rate of the displayed value to 3 times If no change is made for 0 5 sec or longer or the MODE button is pressed the relative settings become active The display will only show the values presently being viewed or V2 00 08 2013 19 User Manual Multispot GII HS3045 HT3030 WW MULTIFOR
26. idual color balance you desire Press the MODE button until the display shows CBAL Use the left right arrow buttons to select any of the following options Rxxx Gxxx and Bxxx with being values between 200 and 255 Value settings below 200 are disabled to avoid unwanted output reduction of the fixture If you want to change the maximum output of the colour being displayed use the buttons to do so For control purposes all LED s are lit with their chosen maximum value All changes made become effective immediately If pressing the MODE button during editing a color level the display returns to CBAL Note Any settings made in this mode will influence the overall color balance of the fixture in all available operation modes also DMX To make sure that several fixtures used together to do not exhibit different color behaviour please make sure that all fixtures used together are calibrated to the same color behaviour V2 00 08 2013 20 User Manual Multispot Gll HS3045 HT3030 MULTIFORM EDIT Automatic DMX addressing This allows to use the first device in a row of units connected via DMX to be used as a master unit and set all subsequent units DMX address automatically On the first master unit in EDIT menu use the left right arrows until the display shows ADMX You can now decide to either address all subsequent units in GDMX mode with the same channel scheme as on the master unit but
27. is minimized without putting strain on the cables or their connections to the terminal blocks 16 Turn the rear cover with the electronics assembly to face its outside Tighten the cover nuts of the PG glands tight enough to make sure the rubber gland seal adapts properly and tightly to the cable s outer perimeter 17 Connect the rear cover with the attached electronics assembly to the main unit by re plugging the connections that have been unplugged in step 3 18 Place the rear cover with the attached electronics assembly on the back side of the power supply compartment NOTE It is extremely important that the rubber seal which is inserted in the groove of the outer edge of the power supply compartment is properly fitted Otherwise the unit may not be waterproof 19 Insert the 6pcs of Hexlnsert screw that hold the rear cover of the power supply compartment and tighten them with 0 6 0 7Nm torque V2 00 08 2013 8 User Manual Multispot GII HS3045 HT3030 WW MULTIFORM INDOOR OUTDOOR CONVERSION 0 La 4 7 RS SS PEO gt ER b 6 B REMOVE CONNECTOR WIRES 5 C REMOVE CONNECTORS E CONNECT CABLE WIRES F RE ATTACH REAR COVER V2 00 08 2013 9 User Manual Multispot GII HS3045 HT3030 MM MULTIFORM INTERNAL CONNECTIONS view from PCB side AC In Out L Red Lead AC In Out N Black Lead MCU PCB Supply DC Red Lead MCU
28. ll remain as last set Note This mode is intended to offer more color options than the static color mode It however is not intended to offer more white shades which means the white channel is not used in the color scroll mode SWITCH STROBE PATTERNS In this mode you will only find hard switching and strobe patterns Press the MODE button until the display shows SPxx whereas xx stands for numbers 0 until 12 The available patterns are defined as follows Pattern Steps Pattern Steps SPO red green SP7 red green blue SP1 blue green SP8 yellow green turquoise blue candy red SP2 blue red SP9 Strobe red SP3 yellow red SP10 Strobe green SP4 candy lime SP11 Strobe blue SP5 candy blue SP12 Strobe white SP6 candy turquoise Use the left right arrows to change the pattern between any of the 13 presets the display shows 5 0 5 12 accordingly and will remain to show unless the speed function is used Use the button to change the speed level or activate the Sound to Light function The first touch of the or button changes the display now showing the speed level SLOO SL25 or S2L representing the following speed levels Setting Speed Setting Speed S2L Sound to Light SL13 1 step per second SL1 1 step per 240 seconds SL14 1 5 steps per second SL2 1 step per 120 seconds SL15 2 steps per second SL3 1 step per 90 seconds
29. n environments with more than 40 degrees environmental temperature Operate the MULTISPOT GII HS3045 HT3030 LED in any closed environment smaller than 10cbm unless forced air convection is provided m Getting started secure mounting The MULTISPOT GII HS3045 HT3030 LED can be mounted in various ways Floor standing operation Turn the bracket to the lower side of the unit and fold out the second inlaying bracket Place the unit in a secure position where it can neither be touched by anyone or could possibly become an objective for anyone to stumble Make sure to comply with cooling requirements of the used power supply if any Hanging Rigging ceiling mounted operation calculating working load limits knowledge installation materials and periodic safety inspection of all installation material and the unit If you lack such qualifications do not attempt the installation yourself Improper installation can result in body injury Be sure to complete all rigging and installation procedures before applying power to the unit Risk of injury Overhead mounting requires extensive experience like Leave the inner and outer bracket folded The unit should be installed out of reach of people and outside areas where persons may walk by or be seated Make sure that the installation area can hold a minimum point load of 10 times the device s weight In fixed installations fix the unit with self locking screws nuts to the mounting point
30. t fade patterns Press the MODE button until the display shows FPxx whereas xx stands for numbers 00 until 07 The available patterns are defined as follow Pattern Steps Pattern Steps FPO red green FP4 candy lime FP1 blue green FP5 candy blue FP2 blue pink red FP6 candy aqua turquoise FP3 yellow lime red FP7 red yellow green turquoise blue candy Use the left right arrows to change the pattern between any of the 8 presets the display shows FP0 FP07 accordingly and will remain to show unless the speed function is used Use the button to change the speed level The first touch of the or button changes the display now showing the speed level 5100 5125 representing the following speed levels Setting Speed Setting Speed SLO 1 loop per 960 seconds 5113 1 loop per 3 seconds SL1 1 loop per 480 seconds SL14 1 loop per 2 seconds SL2 1 loop per 360 seconds SL15 1 loop per 1 5 seconds 513 1 loop 240 seconds SL16 1 loop per 1 25 seconds SL4 1 loop per 120 seconds SL17 1 loop per 1 second SL5 1 loop per 80 seconds SL18 1 2 loops per second SL6 1 loop per 40 seconds SL19 1 4 loops per second SL7 1 loop per 20 seconds 5120 1 6 loops second SL8 1 loop per 12 seconds 5121 1 9 loops per second SL9 1 loop per 10 seconds SL22 2 2 loops per second SL10 1 loop per 8 seconds 5123 2 5 loops per second V2 00 08
31. t the end of its life but shall be returned to authorized recycling stations V V2 00 08 2013 5 User Manual Multispot Gll HS3045 HT3030 WW MULTIFORM LED Lifetime advice LED lifetime is determined by the gradually declining brightness of a LED over time with a point of 50 brightness reduction marking the defined end of its lifetime The driving factor of this effect is the heat that the chip inside the LED is exposed to While a chip may under ideal circumstances reach to more than 100000 hours of lifetime the real world lifetime may only be 30000 to 50000 hours or less if the LED is exposed to excessive heat which can be caused by continuously running all LEDs inside this device at full power and operating the unit in high environmental temperatures If improving the lifespan expectancy is a priority take care of providing for lower operational temperatures This may include forced external cooling and or the reduction of overall projection intensity Unpacking Please check that the box contains the following items and contact your dealer immediately for replacement if any part is missing Main parts 1 pc MULTISPOT GII HS3045 HT3030 LED main unit 1 pc operation manual m Getting started changing the connectors only if required Your MULTISPOT GII HS3045 HT3030 has been factory fitted with connectors for both AC In out and DMX In Out This configuration can be changed with comparatively little effort into an IP6
32. ts filled with liquids such as vases on the unit 6 Do not operate this unit near to open water or in high humidity 7 Choose the position of the AC cord according to the lowest risk of damage by foot steps or by squeezing it 8 Do not open the unit for service there are no user serviceable parts inside Warranty will be void in any case of unauthorized service by the user or other not authorized persons Protection from fire Kan 1 Take care of not placing the unit near sources of heat e g powerful amplifiers fog machines Protection from electric shock 1 Only connect this unit to a mains socket outlet with protective earth connection ground fault earth fault and overload protection 2 Allow at least about 0 15m 6 ins between this unit and other devices or a wall to allow for proper cooling 3 Take always care of sufficient air convection in the units environment to avoid overheating Make sure air convection slots are not blocked Do not operate this unit in environmental temperatures exceeding 40 degrees Celsius 4 Be sure this fixture is kept at least 0 75m 30ins away from any flammable materials decoration etc 5 Do not stick filters masks or other materials directly on the LEDs or the LED cover screen 6 Check the total maximum power of your AC wall outlet if you connect several units to one wall outlet and avoid any overloading 7 device itself has an AC outlet for providing power to other
33. units make sure to not exceed the specified maximum load Protection from injury and damage 1 Never use accessories or modifications not authorized the manufacturer of this unit 2 Choose a location for operation where the unit is protected from vibration and where a fixed mounting position is provided In case of overhead mounting follow applicable rigging requirements 3 Before plugging the AC cord in the wall outlet check whether the AC plug the mains voltage and frequency are the same as this product is specified for If not contact you dealer immediately V2 00 08 2013 4 User Manual Multispot Gll HS3045 HT3030 WW MULTIFORM 4 surface of the device may get hot during operation and heat sink areas may reach to or exceed the limits of EN60950 Do not touch heat sink areas of the device during operation and allow 20 minutes of cool down time after powering off before touching 5 If fluids have spilled into the unit or small parts have intruded the unit immediately switch off the unit and hand it over to the authorized service for a security check 6 Disconnect the unit from AC supply by pulling the AC plug out of the wall outlet or the units AC socket during a thunder storm in order to avoid any damage on the unit due to AC voltage peaks 7 cause of not correct function of this unit or damaged AC cord or other damaged parts pull immediately the AC plug out of the wall outlet and hand the unit
Download Pdf Manuals
Related Search