Home

GDC-450H - MBC - Business Communications

1. 2 2 Installing the batteries The batteries are installed in the battery cavity in the rear of the unit To install the batteries 1 Remove the battery cover located on the rear of the unit Press the latch at the top of the cover and slide the cover down to remove 2 Insert batteries Assure the battery polarity matches the polarity in the battery cavity 3 Place the cover on the unit just below the cavity and push the cover upward until the latch is engaged 4 The unit must be placed in the charger for approximately 6 hours to fully charge the batteries Duration 1 _ Charging Time Mode Time E Full charge 6 hours Standby Mode 150 hours Note Poor care of batteries limits their useful operating life Keep phone in the Charger base when not in use At low battery levels less than 1 battery power bar the display backlight turns OFF to maximize battery charge CAUTION Use only with batteries provided for the GDC 450H Use of other types of batteries may cause harm to the unit or explosion Dispose of used batteries in accordance with local codes and regulations GDC 450H Wireless Handset User Guide 2 3 Connecting the Charger base Unit The Charger base unit must be connected to power using the supplied AC DC Adapter 1 Plug the DC output plug of the adapter into the DC input of the charger 2 Insert the AC plug of the adapter into an AC outlet CAUTION Use only the adapter provided with the unit Use
2. 37 amp X l REGISTER MOBILE _ _ eee MODETA A Obie prong ACTIVATE MOBILE EXT Tel number number registrations Hh mm 41 amp time Set wake up alarm time YOUR WAKEUP TIME gt A hour clock Cancel Wake up Alarm ERASED WAKEUP number Peer heaved DEACTIVATED na 00 USER CUSTOM MSG 01 LUNCH RETURN TIME 02 VACATION TIME TI 32 GDC 450H Wireless Handset User Guide User Pgm Code Display Remark 03 OUT OF OFFICE TIME 04 OUT OF OFFICE DATE 05 OUT OF OFFICE o 06 CALL TO STATION stanon o STATION mme VES ME TIME 09 AT HOME SS Se OFFICE 11 20 UN REGISTER MSG 2 Create a Station User MESSAGE 00 ma Message 53 amp Rm amp Auth DIAL NO 1 9 AND Start a Conf Room PASSWD ee 54 amp Rm amp Auth Close a Conf Room DIAL NO 1 9 AND Code PASSWD a 2 T Set language for the display Domestic English 7 Software Version S W VERSION COUNTRY 5 2 digit for 74 amp Name User name creation NAME each character IP Address DISPLAY GATEWAY IP 15 Display IP address ADDRESS We separator displayed DISPLAY GATEWAY 6 GDC 450H User Menu Features GDC 450H incorporates a menu you employ to control various features and attributes of the handset The Appendix GDC 450H User Menu displays the Menu tree The main sub menus are Call Register Call Log Image amp Sound Phone Register Appointment Phone Settings Direct Call e gt OH To display the U
3. Depending on the system or radio channel environment the system or the wireless terminal may not recognize that the system has the subscribed wireless terminal or the wireless terminal is subscribed to the system Once a user has performed the subscription procedure the user should attempt to make a call Then if a user can t make a call the subscription procedure should be conducted again after selecting the unsubscribe menu item refer to Terminating a Subscription section 2 6 3 Terminating a Subscription Unsubscribing will make a wireless terminal lose connection to the ipLDK 24 100 300 300E IPECS 50 100 300 300E 1200 MG WOTS The subscription data of the phone stored in MPB and WTIB or the wireless terminal should be erased separately at both User Station and Attendant Station using the Unsubscribe procedure To unsubscribe a wireless terminal it should be in an idle state To Unsubscribe from the Attendant Station TRANS PGM O Flex Button 2 Station No HOLD SAVE 1 Press TRANS PGM button TRANS PGM LED flashes and MON LED lights steady 2 Press O 3 Press Flexible button 2 4 Enter the station number 5 Press HOLD SAVE button and confirmation tone is heard 6 Confirmation tone or error tone will be heard at the Station and the corresponding Attendant Station 7 LCD message No Subscription will be displayed if there is no subscribed system In rare cases when subscription data must b
4. Press Menu button 2 Select Phone Register and press OK button 3 Select Reset on the Menu and press OK button 4 Enter HS PIN Code default 0000 using dial button and press OK button 5 Select Handset on the menu and OK button 3 Using the Basic Features Some buttons have multiple functions In some cases a button will activate one feature when simply pressed and activate another feature when the button is pressed and held for a little longer than 1 second For example turning the power ON and OFF is done using the End amp Power button Pressing the button will end an active call holding the button turns power OFF Buttons may also provide different functions depending on the state of the phone when idle the button may provide one function and when busy the button activates a different feature Local phone features are generally accessed by a button with the handset idle while system features are accessed when the phone is in the talk mode waiting to dial In many cases a dial code a series of digits is required to activate a feature Since dial codes are different for each system and may be changed through Admin codes are referenced by name Code digits are available from your System Administrator or perhaps the Attendant 3 1 Turning the GDC 450H ON and OFF Your new Wireless handset operates on 1 Li ion rechargeable batteries When not in use it should be turned OFF to extend the life of the batteries Fully
5. W W W WW B E H K N P U W E bd d Ed Kl 48 User Guide GDC 450H Wireless Handset Spanish Language Character Chart o miwir xi zia DIZ o eeehe 1 Button q DEE B E a Ga n C G Ea Ga iesse del vlelez2gle EERE Dial Pad button Russian Language Character Chart BCEE P UI EIS TCIOlIsl zi IERT gd ielsdizisislaissl 1 slaislsiele aale ls N G QN vu N all Been rail Le O est ell D button EC 8 u 9 0 18 49 10 GDC 450H User Menu 1 Call Register Missed Call GDC 450H Wireless Handset User Guide Missed Calls Received Call Received Calls Dialed Calls Dialed Call All Calls Delete Call Wallpaper 1 Ringing Type gt Tone 1 9 Wallpaper 2 Volume gt _ Volume 1 9 2 Images A Sounds CN Images Wallpaper 3 Sounds Blank By Ring No Sound Internal Ring By Vibrator Ext
6. 3 Connecting the Charger base Un 9 2 4 Installing the Belt Clm 9 2 9 Installation of Wireless Termmmal 10 2 6 Subscribing the GCD 450H to a Gvsiem ees 10 ZO Enabling SUDSCHPUONS EE 10 20 2 SUDSCKIDING LO TNE Sy SIC IMac a eae ate 10 20 9 Terminating a SUDSEMDUOM WEE 11 2 1 Loft e ten EE 12 2 8 Registering GDC 450H to LWS BS LG Ericsson Wireless SOHO BaSe SUA OM REG 13 2 8 1 Enabling Registration EE 13 20 REJ SENNO TO the LWS EE 14 2 8 3 Terminating a registration from WR 14 A Using the Basic Features ccccsccesseceeeeeeeseneseeeseneseneees 15 3 1 Turning the GDC 450H ON and OFF 15 3 2 VOUME AJUSTE Gorenn ai 16 O22 AdU USNMEMME AUGIO VOIUIMNG EE 16 3 2 2 Adjusting Ihe RINGS WOUHIER eegene gege deeg dee deg 16 3 3 Mung YOUR MICrOPNONG EE 16 3 4 Placng an OUISIOS e E 16 3 5 Kl TC UE 17 3 6 Eier 17 3 FACING eC ANON Hold EE 17 3 8 cal Trans TO EE 18 3 9 DONO Distr R CIE RE 18 3 10 tast NUMDETF REAA sigran E 18 3 11 System Last Number Redial cccccccsccesceeeseeeceeseseceeeseesaees 19 3 12 w lle Die H RI EE 19 GDC 450H Wireless Handset User Guide 3 13 system Save Number Hecdal 19 4 le e E nee 20 4 1 Dialing rom leie Lee 20 4 2 Adding Records to the Phonebook sensnnnennannnnnnnnennnnnnnnnrennenne 20 4 3 Modifying Records in the Phonebook aannnnannannnnnnnnnnnnnnnnnnnnnn 21 4 4 Deleting records from the honebook 21 4 9 searching the Phonebook with Eug 21 5
7. LG ERICSSON 2 GDC 450H DECT Wireless Handset User Guide Please read this guide carefully before operating your new Wireless handset Retain the guide for future reference GDC 450H Wireless Handset User Guide Regulatory and Safety Notices 1 Radio Frequency Emissions FCC Compliance statement This device complies with Part 15 rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment into an outlet on a different circuit from that to which the receiver is connecte
8. OK GM left soft button the selected reset is implemented Press the End RS button PALON Cle Es 38 GDC 450H Wireless Handset User Guide 6 4 Creating amp Modifying an Appointment Your GDC 450H Wireless handset has an Appointment Reminder feature When set the handset will remind you of an Appointment with a display of the appointment text and an appointment alert alarm sound or vibration alert if in silent mode In addition to the time you can enter the appointment text and set the appointment as daily monthly or annual To set an appointment reminder 1 2 P T 8 9 Select the Appointment menu from the User Menu Press the Set RW left soft button the Interval menu appears Daily Monthly Annual Use the Navigation O button to highlight a selection Press the OK I left soft button to access the sub menu Use the dial pad to enter For daily enter the time of day as hh mm in a 24 hour format For monthly enter the day and time as DD hh mm with 2 digits for the day For annual enter the day month and time as DD MM hh mm with 2 digits for the month Press the OK RW left soft button to store the appointment lf desired use the dial pad and Character Chart in the Appendix to enter a 12 character reminder message Press the OK RW left soft button to store the appointment Enable or disable the appointment with the Enable or Disable REH or WER left or right soft b
9. The host LG Nortel system stores the last ten 10 external numbers called by the GDC 450H in system memory These numbers can be accessed and the number selected for quick redialing To use System Last Number Redial 1 Press the Talk EEA button 2 Press the Speed Program RRE button 3 Press the asterisk W button the last seven numbers are shown in the display 4 Use the up and down arrows on the Navigation O button to highlight the desired number 5 Press and hold 1 second the right arrow on the Navigation button with the number highlighted The handset places a call to the selected number Note This feature works with external calls only internal calls are not registered for System Last Number Redial 3 12 Handset Speed Dial The GDC 450H incorporates a Phonebook that can contain up to 60 records Each record contains a name number and a record number Numbers from the Phonebook can be automatically dialed by entering the Phonebook record number 1 60 Refer to the Phonebook section later in this guide for details on the Phonebook To speed dial a number from Phonebook 1 Dial the Phonebook entry number 1 60 holding each digit for longer than 1 second lf a number is stored in the entry the number is dialed automatically If no number is stored for the Phonebook entry the dialed digits are ignored 3 13 System Save Number Redial You can save a number in the host system memory for quick access
10. Wireless SOHO Base Station Prior to accepting a connection with a GDC 450H a registration to services must be entered into your LWS system This is accomplished in a two step process the LWS BS enables registration of a phone to the system then the GDC 450H subscribes to the LWS BS for services 2 8 1 Enabling Registration To enable a registration from the LWS BS 1 Press Menu button 2 Press Digit 1 CONFIGURATION submenu or Select 1 CONFIGURATION using Navigation up down key and OK Button 3 Press Digit 4 STATION REGISETR submenu or Select 1 STATION REGISTRATION using Navigation up down key and OK Button 4 Press Digit 1 REGISTER STATION submenu or Select 1 REGISTER STATION using Navigation up down key and OK Button Select the phone type using Navigation left right key GDC 4XX Press Navigation OK button or OK soft key When the registration is completed below message is shown on LWS BS LCD STATION 10X SUBSCRIBED SUCCESS EE Note Don t press Monitor or Speaker button at the LWS BS until the GDC 450H completes the registration and registration confirmation tone is heard 13 GDC 450H Wireless Handset User Guide 2 8 2 Registering to the LWS BS When registering to LWS BS you will need the system s unique Radio Frequency Personal Identification RFPI Also before starting the registration process make sure you are close to an active LWS BS To register to the system from the G
11. amp Modifying an Appontment 39 6 5 PNONGE SEINO EE 39 6 5 1 Clock Date and Time depnlay 40 O2 AlI ee EE 40 69 3 Keypad Ke EE 41 SE 6 E 41 Goo ANNA EE 41 690 Sleen d le el 42 6 9 7 Keypad RE ee 42 ee SVN DEE 43 099 EIERE 43 69210 Missed Cal MOOG EE 43 6 5 11 Range Out DGC Ds ecesna waden ede sacar sce EETAS 44 6 25 12 EEN 44 6o 13 gt PUIG ANSWEP EE 44 6 6 DECEO UE 45 7 PROUDICSIMNOOUING DE 46 SPEECH 47 9 Dial pad Character Charts cccssecssseeensecesecenesensesenees 48 10 GDC 450H User d UE 50 GDC 450H Wireless Handset User Guide 1 Introduction Thank you for selecting the LG Ericsson GDC 450H Wireless handset With our GDC 450H you will experience great in building mobility with access to all of the many features and functions of your LG Ericsson communication system This guide is intended to provide you with detailed information on the use of your new LG Ericsson Wireless DECT handset GDC 450H is a wireless handset that employs DECT technology to provide local in building mobility Wireless Radio Frequencies RF signals are exchanged between the handset and base stations GDC 400B 600B Multiple base stations connect to the Wireless Management Interface WMI in your LG Ericsson phone system The WMI links the connected base stations forming a larger Base or Zone Within this zone transparent handover of active communications between base stations in the zone is supported 1 1 Descrip
12. be dialed To dial a number form the Phonebook 1 Access the Phonebook menu as described above 2 Use the Navigation to highlight the Find selection and press the OK RR left soft button the Enter Name prompt is displayed Search the records 1 Enter the first few characters of the name using the dial pad refer to Appendix Dial Pad Character Charts As an example press 5 twice for k and 3 twice for e to search for Kenny 2 Press the Find RR left soft button to display the matching record 3 When the record is found press the Call RR right soft button to dial the number 3 Press the Find RW left soft button to search all records 4 Use the Up and Down arrows on the Navigation to highlight the desired record 5 When the record is found press the Call J right soft button to dial the number 4 2 Adding Records to the Phonebook To add a record to the Phonebook 1 Access the Phonebook menu as described above 20 GDC 450H Wireless Handset User Guide 2 Use the Navigation to highlight the Add selection and press the OK RR left soft button 3 Enter the each character of the name using the dial pad Up to 14 characters including numbers may be entered See the charts in the Appendix Dial pad Character Charts If you enter the wrong character use the Delete BER right soft button to delete a character 4 Enter the phone number for the record using the dial pad and press t
13. directly below item Talk button Connects handset to host system to answer incoming or place outgoing calls Recall Flash Clear button active call state register recall flash to regain dial tone idle state press to clear single digit press and hold 1 second to delete all digits Silent Alert button idle and dial state press to dial x press and hold 1 second to turn Silent Alert ON and OFF active internal call camp on from host Call back button Leave a call back or recall message End call amp Power button Press to end a call or reject a call press and hold 1 second to turn power ON amp OFF Dial Pad buttons Lock button idle and dial state press for press and hold 1 second to lock dial pad Speed Program button Host dial tone press to access Station or System Speed dial press and hold 1 second for host program mode D GDC 450H Wireless Handset User Guide Battery cover Belt Clip e Battery charging terminals External Ear Mic jack w cover lf an Ear Microphone Headset is attached to a GDC 450H it can receive or release a call It is recommended to use a Headset meeting JIS C 6560 Specification Press the button on the Ear Microphone Headset to receive an incoming call when ringing and do the same action to release the call Making a call by using the Ear Microphone Headset is supported too press the button once on the Ear Microphone Headset when in the id
14. of a different adapter could damage the unit or cause a fire and will invalidate your warranty 2 4 Installing the Belt Clip The GDC 450H comes with a belt clip that can be installed on the unit To install the belt clip refer to the figure and instructions below When installing the belt clip 1 Turn the screw clockwise on the back of the unit 2 The belt clip is pulled upward until the screw is inserted into the hole securely When uninstalling the belt clip 1 The belt clip is pulled down with pushing the button of the belt clip until the lock is open GDC 450H Wireless Handset User Guide 2 5 Installation of Wireless Terminal Before using the GDC 450H the wireless terminal must be subscribed to a System The subscription process must be conducted at the User Station and at the Attendant Station to ensure proper function of the wireless terminal Proper Authorization Codes should be obtained from the System Administrator or the Attendant before processing the subscription refer to Subscribing the GCD 450H to a System The wireless terminal is allowed to be subscribed to up to 4 GAP systems If a user wants to subscribe to more than 4 systems the wireless terminal first should be unsubscribed from one of the systems This subscription procedure can be performed by a User There are two methods to unsubscribe the wireless terminal from the key system Q The User can unsubscribe from the system and the wireless terminal a
15. polyvinyl chloride tube of battery Do not short circuit Accidental short circuiting can occur when a metallic object like a coin a clip or a pen causes a direct connection of the and terminals of the battery You may get hurt or it may fire by generation of heat or explosion BS ESO ei When smells something burning using a phone or RRDA gt charging a battery plug off power source or phone line ai Sa Call for service center If left intact for long time it may E b be a cause of fire or electric shock Do expose of battery in designated place If not treated properly it may be dangerous GDC 450H Wireless Handset User Guide About Using the Phone Only qualified service personnel can install or repair phone equipment Consult your authorized LG Nortel dealer for help It may be a cause of fire electric shock and breakdown Avoid exposure to a volatile matter such as benzene alcoholic and acetone It may be a cause of fire transformation and discoloration Do not insert metallic object or foreign matters If inserted plug off and call for service center it may be a cause of fire or electric shock Do not expose to near place where gas leaks H leaking do not touch phone or outlet Open the windows to let fresh air in A spark may cause explosion fire or burn When lightning do not touch power plug or phone line It may be a cause of an electric shock or death When smoke or smell somethi
16. second the Speed Program RE 1 button Dial the Cancel Temporary COS code default 22 Dial Enter your Authorization code PIN Press and hold 1 second the Speed Program RE 1 button Press the End Wm button Or oN Note A user authorization code is required to restore COS 5 13 Paging The host system incorporates voice broadcasts to other stations and external speakers During a page voice is broadcast to the speaker of idle stations assigned to receive the page Each station is assigned to a page group known as a zone and individual zones are paged The Dial code and number of page zones vary between systems ask System Administrator for Page zone dial codes To Page over the host system 1 Press the Talk EEA button you receive dial tone 2 Dial the Page zone see your System Administrator for Page Zones codes 3 After the confirmation tone speak in a normal voice your voice is broadcast to the zone dialed 4 When done press the End Rm button 28 GDC 450H Wireless Handset User Guide A paging party may request another user join in a conversation The paged party can respond to the page and the two parties are joined in a private conversation To respond to a request to join a conversation 1 Press the Talk Sep button you receive dial tone 2 Dial the Meet Me code default is 544 3 After the confirmation tone a private connection is established to the paging party 4 When done press the E
17. station user does not answer your call or is in DND you may request the user callback when available The station receives a Message Wait indication and responds using the procedure in Responding to a Message Wait section discussed later in this guide To leave a return call request 1 When your call to another station is unanswered or you receive DND tone press the Call back SSM button you will receive confirmation or if available the option to leave a voice message 2 Follow the voice instructions to leave a voice message 3 Press the End Rem button Note You may wish to leave a voice message When given the option follow the verbal instructions of the Voice Mail system 5 4 Camping on to a Busy Station If you receive busy tone when calling another station you may request to alert the called party of your call waiting When camped on the system sends a call wait tone to the busy station The busy user can decide to place the active call on hold to respond to your call ignore your call or enter DND To camp on a busy station and send a Call Waiting signal 1 While receiving internal call busy tone press the asterisk Sen button you and the called user receive the Call Waiting tone 2 Wait until answered or press the End Re button to leave a call back request To answer a Call waiting if you receive a call waiting tone 1 Press and hold 1 second the right arrow of the Navigation button The act
18. to the system Administrator for more details 5 19 Responding to an Authorization PIN Request In order to manage wireless terminals the Attendant may request you to enter your PIN When the display message PIN appears you must respond by entering your PIN Authorization code To enter your code 1 Press the Talk Be button the dial tone will be heard 2 Enter your password with the dial pad 3 Press and hold 1 second the Speed Program EZA button 5 20 System Voice Announcements If the host system includes an integrated voice response system your handset can play various announcements as well as voice mail features Announcements include the Date amp Time Station Number and Status The status prompt includes e Station number XXXX e Listed message X e Wake up time XXXX AM or PM Do not disturb Forwarded to station XXXX Forwarded to speed bin STA HUNT XXX Locked temporary COS change COS X To hear a prompt Press the Talk 438 button you receive dial tone Press and hold 1 second the Speed Program RER button Dial the Prompt code See your System Administrator for codes Press and hold 1 second the Speed Program EZA button Press the End WE button o gt a E 5 21 Using System Voice Mail Your host system may have one of several voice mail sub systems including integrated or 3 party options For details on your Voice Mail contact your System Administrator 5 22 User Program
19. your system To respond to a message wait from an ipLDK system w integrated mail option 1 2 3 Press the Talk EAA button you receive dial tone Press the Call back MEJ button If you have a station callback message the Station is called If the message Is a voice mail the first voice message is played Press and hold 1 second the right arrow on the Navigation button for the next voice message To replay a message press the Call back ER button To erase a voice message press the Recall Clear W button Press the End Ren button If you have responded to all your messages the message waiting indication is terminated To respond to a message wait from an iPECS system 1 Press the Talk IEAA button you receive dial tone 2 Press the Call back DER button The system sends the message summary display as below This display shows the types of messages and the number of each waiting St Ch VS Wiel Ue MIs GL US U6 Ud US ll For ST station call back messages dial 1 and press the Call back a button to return the message To delete a station message without a call back press the and 1 digits to delete all station messages without a call back press the and 1 For CL missed call with CLI messages dial 2 and press the right arrow on the Navigation button to return the call To delete the current CLI message press the Call back ER button and to delete all CLI messag
20. C 450H Wireless Handset User Guide Do not lay a carpet cushion and etc on the phone Do not put adapter near heat appliance It may be a cause of fire or electric shock Do not put heavy things on the power cord Do not bend power cord too much It may be a cause of fire or electric shock Do not remodel the power cord or disassemble If power cord or plug are impaired do not use it It may be a cause of fire or electric shock When power cord stained with dirt polish power core and plug into the outlet firmly It may be a cause of fire When install phone in other place check with the phone line and plug It may be a cause of fire or electric shock Before using plug check with home power voltage Inaccurate power voltage may be a cause of fire When changing battery out of the phone leave it children not to chew or suck up the phone If children swallow it consult a doctor for medical treatment GDC 450H Wireless Handset User Guide o i CA pe When battery electrolyte runs out of it be careful of w touch in eye skin or cloth If touched wash it clean and Ag consult a doctor A keep Do not throw and impact battery Do not dispose of oh batteries by putting them in fire It may explode or fire by electrolyte Do not disassemble or remodel Use only batteries and adapter approved by the phone manufacturer You may get hurt or it may fire by generation of heat or explosion Do not peel off the
21. Codes The host system permits user control of a number of features including Temporary COS Wake up Alarm Clock etc You access the various controls through the User Program Pgm feature using codes The various codes and features vary between systems your System Administrator can provide you with available codes The table below is an example of User Pgm codes and their use To access a User Program 1 Press the Talk IEAA button you receive dial tone 31 GDC 450H Wireless Handset User Guide 2 Press and hold 1 second the Speed Program EZA button 3 Dial the User Pgm Code and any required entry See your System Administrator for codes 4 Press and hold 1 second the Speed Program RH button 5 Press the End WE button Example of User Program Code Chart User Pgm Code Display _ Remark CALL COVERAGE 14 amp x 1 On 0 Off x 1 0 Call Coverage MODE DELAY RING CYCLE Dial 0 9 Temp COS ICM ONLY MODE ENTER CURRENT Restore COS PASSWORD a COS OVERRIDE CODE 23 Persia Ge User Authorization J Code NN 1 ST STATION MSG 2 CL CALLER ID MSG 3 VS SYSTEM VOICE MAIL VOICE MAIL Mo SSR VM 6 SMS MESSAGE H 33 amp System Authorization code ENTER CURRENT Station No PIN PASSWORD Auth Code as DID Call Wait DID WAIT 1 On 0 Off wale Select Msg alert choice CHOICE EXE SEC MSG 1 On O Off 36 amp x type Create and send or resend SMS SEND MODE Resend 1 message Edit 2
22. DC 450H 1 Press the Menu RR button to display the menu 2 From the menu use the Navigation button to highlight Phone Register 3 Press the OK IA button this displays the Phone Register menu 4 Select LWS Subscription using the up and down arrows of the Navigation O button and press the OK Ce button 5 The GDC 450H searches for the LWS BS displaying and Searching 1 When a LWS BS is found its RFPI is displayed The RFPI of your LWS BS is available from your System Administrator or perhaps the attendant 6 Press OK RR button while highlighting the RFPI to continue the registration to the system or Press No button to continue the search 7 Press OK RER button on successful registration a confirmation tone is received at the GDC 450H and the LWS BS 8 If the registration fails repeat procedure from Step 1 to 6 at the LWS BS and Step 1 to 8 from the GDC 450H refer to Note Note Depending on the LWS BS or radio channel environment the LWS BS or the wireless terminal may not recognize that the LWS BS has the subscribed wireless terminal or the wireless terminal is subscribed to the LWS BS Once a user has performed the subscription procedure the user should attempt to make a call Then if a user can t make a call the subscription procedure should be conducted again after selecting the unsubscribe menu item refer to Terminating a Subscription section 2 8 3 Terminating a regist
23. DND Do Not Disturb feature is active the GDC 450H will not notify you of an incoming call The handset will not ring or vibrate allowing you to work without interruption from an incoming call The host LG Ericsson system determines routing of the incoming call while your phone is in DND To activate DND 1 Press the Talk MEEA button 2 Dial the DND code default 553 a confirmation tone is received and the handset enters DND 3 Press the End Rem button The wireless terminal returns to an idle state To deactivate DND 1 Press the Talk Be button 2 Dial the DND code default 553 confirmation tone is received and the handset enters DND 3 Press the End RS button The wireless terminal goes to an idle state 3 10 Last Number Redial The GDC 450H stores the last ten 10 numbers called in memory These can be internal or external phone numbers These numbers can be accessed and a number selected quickly for redialing To use Last Number Redial while idle 1 Press the right arrow on the Navigation button The last seven dialed numbers are displayed 2 Use the Navigation button to highlight the desired number and press the left GES soft button This will access the Option menu 3 Use the Navigation button to highlight Call in the Option menu and press the left RECH soft button The selected number is dialed 18 GDC 450H Wireless Handset User Guide 3 11 System Last Number Redial
24. Dial number Press the Talk IEAA button you receive dial tone Press and hold 1 second the Speed Program EZA button Press the Speed Program RER button Dial the Speed dial bin location Press and hold 1 second the Speed Program Em button as Ee Note Depending on the host system the number of Station Speed dials available the length of the stored number and special instructions available will vary check with your System Administrator To use a Station Speed Dial 1 Press the Talk EAA button you receive dial tone 2 Press the Speed Program RRE button 3 Dial the Speed dial bin location 5 8 Using System Speed Numbers In addition to Station Speed Dials the host system includes memory to store system speed dial numbers available to all stations connected to the system These numbers are stored by the attendant or System Administrator To use a System Speed Dial 1 Press the Talk IEAA button you receive dial tone 2 Press the Speed Program RH button 3 Dial the Speed dial bin location Contact your System Administrator for System Speed dial numbers available Note In some cases your access to Speed dials may be limited in the system check with your system Administrator 5 9 Call Forward You may select to have your incoming calls re routed to another station a station group or voice mail To activate call forward for your calls 1 Press Talk MERJA button you rece
25. End Rm button Seas Ss Note The Alarm Clock employs the handset clock to determine the time Assure the handset clock is set properly when using this feature It is not required to display the handset time but it must be set properly for the Alarm clock to work as expected The Alarm clock will remain set and repeat on a daily basis or cancel as needed 40 GDC 450H Wireless Handset User Guide 6 5 3 Keypad Tones When a button on the handset is pressed a keypad tone is generated This tone can be enabled or disabled through the Keypad tone selection under the Phone Setting menu To enable or disable the Keypad tone 1 Select the Phone Setting menu from the User Menu Use the Navigation button to highlight the Keypad Tone selection Press the OK RER left soft button to access the sub menu Use the left or right arrow of the Navigation button to select Yes or No Press the OK QM left soft button to store the setting Press the End RS button 2 OV ey 6 5 4 Display The Display sub menu allows the backlight and dialed digit color to be adjusted The backlight can be adjusted to standard always on always off or sleep mode In Sleep mode the back light is set to standard backlight turns OFF 20 seconds after the last button press and turns the phone OFF after one minute after the backlight The dialing color can be set to Yes which varies the color of each digit or No which uses the same co
26. SA C22 2 No 60950 1 UL 60950 1 3 E 911 and use of the GDC 450H with Multi Line Telephone Systems Please note the use and operation of this phone as part of a multi line telephone system MLTS may be subject to state and or federal E 911 MLTS laws that require the MLTS to provide a caller s telephone number extension and physical location to applicable state and or local emergency services when a caller initiates a 911 call The MLTS may not provide a caller s telephone number extension or physical location information to emergency services when a caller dials 911 and compliance with state and or federal E 911 MLTS laws is the sole responsibility of the purchaser of this phone 4 Privacy GDC 450H implements security and encryption technologies appropriate for DECT however privacy of communications may not be ensured when using this telephone GDC 450H Wireless Handset User Guide Important Care amp Precautions Before connecting or using your new phone take a moment to consider safety and reliability Use common sense when locating connecting and using your GDC 450H The GDC 450H uses 3 7 VDC Li ion batteries Replace batteries only with identical size and type available from your local LG Ericsson dealer Use of a different battery type may cause damage to the phone or charger and may cause fire or explosion Dispose of batteries in accordance with any local codes or regulation The Charger base unit should only be used on a d
27. Sounds Section ARE Heiser No active Subscribe the handset refer to Subscribing EE subscription the GCD 450H to a System in the LCD Low battery icon is flashing on LCD with Battery level is low Recharge the battery warning tone Battery level is Power Er gab ance below operational Recharge the battery power ON SS Insufficient RF from Move to obtain higher RSSI wait for RF base station no RF lock to base station lock to base station Keypad tones are Use Up and down arrow on Navigation Tone is low or high when pressing a digit disabled or tones button to adjust volume Check Keypad volume needs Tones are enabled disabled in the User adjusting Menu Unexpected call Poor RF RF can change over time move to obtain disconnect or call failure environment higher RSSI SC Batteries failing Charge batteries and keep handset in Battery duration is less l e and or poor battery cradle when not in use refer to Installing the than specified b charging habits Batteries Section Interference from other DECT system Too far from Base Turn other DECT systems Off station no available Assure handset is in range of base station channel or wrong Assure RFPI and AC are correct Base station RFPI Wait for an available wireless channel Subscription fails or Auth code selected When pressing TALK button the Phone icon a blinks several times and disappears When pressing TALK HR SEN A
28. Using Advance System Features c ccccssseesessesenseeeeeeeeees 22 5 1 Program a System User Name 22 J2 Request a Busy Station Call Back 22 9 3 Leaving a Return Call Message 0nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 23 5 4 Camping on to a Busy Station 20 0 0 cece ccecceeeeeeeeeeeeeeeeeeeeeaeeeeees 23 5 5 Bis ebe lei E TE 23 5 6 Answering a Call Ringing at Another Station ccceeeeee ees 24 SWA Using Station Speed UDialmmg 24 5 8 Using System Speed Numbere 25 5 9 cal FOWAO E 25 5 10 Pre defined amp Custom Text Messagmg 26 5 11 Responding to a Message Wait Indicaton 27 5 12 Blocking Outgoing Calls w Temporary CO 28 5 13 Kiel ie 28 5 14 C R E 29 5 15 Bel Tee e E 29 5 16 UINIVErSal NIGME ANS WOM sni EN 30 5 17 Using the System Alarm CJock 30 5 18 To Register a System Access Authorization Code PIN 30 5 19 Responding to an Authorization PIN Heouest 31 5 20 System Voice Announcements cece eecceeceeeceeeseeeeeeeeeeaeeeeees 31 5 21 Using System Voice Mail ccccccccsscceecceeceeeceeeeeeceeeeeeseeeseesaes 31 5 22 User Program Codes eet 31 6 GDC 450H User Menu Features ccccsseceeseeeseeseeeeeees 33 6 1 Call Register Call og 34 6 2 NAA ON OUIN E 35 SEN NEE en Ee EE 35 O22 e elle E 35 GDC 450H Wireless Handset User Guide 6 3 MONG e E e 36 SE es SUDSCIPION EE 3 7 A SECINA DECT ZONG EE 37 Bee MOAI PUN ecciesia TNN 38 094A BaSe EE 38 Eaa E 38 6 4 Creating
29. al the number Note that unlike the pre dialing above digits cannot be deleted 16 GDC 450H Wireless Handset User Guide 3 5 Releasing a Call While on an active call incoming or outgoing you may release the call at any time To release a Call 1 Press the End Ram button The wireless terminal ends the call and returns to an idle state 3 6 Answering a Call When a call is received you receive a visual indication of the incoming call The Call type icon flashes EXT or INT indicating an external or internal call and the calling number is shown If the number is stored in the local Phonebook the associated name is displayed In addition to the visual indication you receive either an audible ring or the phone vibrates based on handset set up selection refer to incoming call alert setting You may answer or reject the call both will terminate the incoming call signals at the handset To answer an incoming call 1 Handset rings the Call type icon flashes and Caller ID is displayed if available 2 Press Talk EBJA button to answer a call the phone icon s and the Call type display Note If the handset is in the Charger base lifting the handset out of the charger automatically answers an incoming call To reject the incoming call and stop the incoming call signal 1 Press the End RS button all signaling stops but the caller hears ring back tone 3 7 Placing a Call on Hold While you are on a call using th
30. alls can be made unlocked Dialed digits and special characters R P Pause D Go to DTMF R Flash GDC 450H Wireless Handset User Guide 1 1 3 Charger base Unit The Charger base unit p n GDC 450SSC is used to charge the GDC 450H handset and to house the handset when not in use Terminals in the charger mate to terminals in the bottom of the handset to allow the batteries to charge Fully charged batteries provide about 20 hours of talk time or about 150 hours of standby time To fully charge dead batteries requires about 6 hours in the Charger Battery charging terminals Charging Phone in use LED DC input jack connect to AC DC Adapter GDC 450H Wireless Handset User Guide 2 Getting Started Before you can begin to use your new GDC 450H you must unpack the unit install the batteries charge the unit and register the item for service to your telephone system This section provides you the information needed to complete these steps 2 1 Unpacking the GDC 450H Each GDC 450H package contains the items below These items include the GDC 450H handset Charger base AC DC adapter Li ion batteries this User Guide and a belt clip Unpack the carton and assure all items are available l Id IN EP e r l i I Ta N g i i iy J i ma Il A Charger Bas GDC 450H GDC 450SSC Batteries User Manual Belt Clip Ear Microphone GDC 450H Wireless Handset User Guide
31. at a later time To save a number while on an outgoing call 1 Press Speed Program EZDA button twice during a call To dial a Saved number 1 Press Talk Rep button 2 Press Speed Program Em button 3 Press the pound 9 button Note If the line used to make the original call is busy redial uses an available line from the same line group This feature works with external calls only and will not work for internal calls calls within the host system 19 GDC 450H Wireless Handset User Guide 4 Phonebook The GDC 450H incorporates a Phonebook that stores up to 60 contact records and each record has a name and phone number The name can be up to 14 digits in length characters and numbers From the Phonebook menu records can be searched called added modified or deleted When a call is received from a contact in the Phonebook the name associated with the number is displayed There are several methods to access the Phonebook menu based on the state of the phone idle or busy To access the Phonebook menu While idle 1 Press the Names RR right soft button OR 1 Press the Down arrow on the Navigation button While in Talk mode 1 Press the Options WA left soft button this displays the Options menu 2 Use the Navigation to highlight the Phonebook selection and press the OK RE left soft button 4 1 Dialing from Phonebook Records in the Phonebook can be searched and a number can
32. ate and time set The display is enabled as outlined in the Clock Display menu section later in this guide To set the date and time 1 Select the Phone Setting menu from the User Menu Use the Navigation button to highlight the Clock selection Press the OK I left soft button to access the sub menu Use the dial pad to enter the date as ddmmyy Press the OK QM left soft button to accept the date Enter the time of day as xx xx in a 24 hour format Press the OK RR left soft button to accept the time ALON OT ely Note If you set and enable the clock display and the host system provides time and date when you press the Talk MEEA button before dialing the display will change to the system time and date The Clock Display must be enabled to display the handset time 6 5 2 Alarm Clock The GDC 450H incorporates an Alarm Clock feature When the handset clock reaches the alarm time you are notified by the alarm To set the Alarm Clock 1 Select the Phone Setting menu from the User Menu Use the Navigation button to highlight the Alarm Clock selection Press the OK RER left soft button to access the sub menu Use the left or right arrow of the Navigation button to set or cancel the alarm Press the OK RR left soft button to store the appointment If you wish to set the Alarm enter the time of day as hh mm in a 24 hour format Press the OK RW left soft button to accept the time Press the
33. below and the time and date are set as outline in the Clock Date and Time Display section earlier in this guide To enable or disable use of the handset date and time 1 Select the Phone Setting menu from the User Menu Use the Navigation O button to highlight the Clock Display selection Press the OK RER left soft button to access the sub menu Use the left or right arrow of the Navigation button to select Yes or No Press the OK QM left soft button to accept the date Press the End WE button D e SS Note If you set and enable the clock display and the host system provides time and date when you press the Talk em button before dialing the display will change to the system time and date The handset date and time must be adjusted as outlined in the Clock Date and Time Display Section After changing the Clock Display you must press the Talk EEEa and End Gay buttons to activate the display 6 5 13 Auto Answer Mode You can select for your phone to activate deactivate Auto answer mode when lifting your phone from the charger after incoming call alerting To enable or disable use of the handset auto answer 1 Select the Phone Setting menu from the User Menu Use the Navigation button to highlight the Auto Answer Mode selection Press the OK RW left soft button to access the sub menu Use the left or right arrow of the Navigation O button to select Yes or No Press the OK E left soft
34. button to accept the date Press the End Rm button So 2 by 44 GDC 450H Wireless Handset User Guide 6 6 Direct Call The GDC 450H can be configured to dial a specific number when any button on the handset is pushed The Direct Call or Hotline number can be enabled and the number to call specified The direct call emergency number is transmitted on input from any key This feature may be used in cases where the User is not able to effectively dial a phone number and would need direct access for assistance from the Attendant or another party To enable Direct Call and input a number 1 2 3 4 From the User Menu use the Navigation button to highlight Direct Call Press the OK WE left soft button Use the Navigation button to select Yes or No and press the OK RW button If you select Yes enter the Direct Call number and press the OK WA button 45 GDC 450H Wireless Handset User Guide 7 Troubleshooting Solution Problem Possible Cause Assure batteries are properly installed and LCD is blank No power charged Press and hold the End Power button for 1 second NO CHANNEL displayed when TALK button a i Wait until a channel is available pressed Volume needs While connected to a call press Up or Low or high audio volume ee eee adjusting Down arrow on the Navigation button Low or high ring volume Volume needs Adjust Ring volume level refer to Image and adjusting
35. charged batteries provide about 15 hours of talk time or about 120 hours of standby time To turn the power ON or OFF Power ON 1 Press and hold 1 second the End Power RS button to turn power ON the handset displays Range Out while searching for a base station After the handset locates a base station the Antenna and RSSI icon displays Power OFF 1 Press and hold 1 second the End Power Wm button to turn power OFF After a validation tone is received the handset switches OFF 15 GDC 450H Wireless Handset User Guide 3 2 Volume Adjustments 3 2 1 Adjusting the Audio volume During a call you can adjust the audio volume from the earpiece level 1 to 7 To adjust the audio volume 1 While on a call press the Up or Down arrow on the Navigation gt button 3 2 2 Adjusting the Ringer volume You can adjust the ringer volume separately for internal and external calls level 1 to 9 To adjust the ringer volume level 1 Press the Menu CR button to display the menu 2 Inthe menu use the Navigation button to highlight Image amp Sounds and press the OK Ri button this displays the Image and Sounds menu 3 From this menu select Sounds using the Up and Down arrows of the Navigation button and press the OK i button 4 From this menu select External Ring or Internal Ring to set the ring volume for external or internal calls respectively and press the OK button 5 Use the Up and Down arro
36. d This Equipment has been tested and found to comply with the limits for a Class B digital device If problems persist consult the dealer or an experienced radio TV technician for help Canadian Compliance statement This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada This device complies with Class B limits of Industry Canada Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation European Union Declarations of Conformity LG Ericsson Co Ltd declares that the equipment specified in this document which bears the CE mark conforms to the European Union Radio and Telecommunications Terminal Equipment Directive R amp TTE 1999 5 EC including Electromagnetic Compatibility Directive 89 336 EEC and Low Voltage Directive 73 23 EEC The product fulfills the essential requirements of the harmonized standards shown above 2 Product Safety Instructions This product complies with and conforms to the following international Product Safety standards as applicable Safety of Information Technology Equipment IEC 6095 1 including Relevant national deviations as listed in Compliance with IEC for Electrical Equipment IECEE Safety of Information Technology Equipment CAN C
37. e GDC 450H you may place the caller in a waiting state where the caller hears music on hold This allows you to place another call or answer a call waiting To place a call on hold 1 Press and hold 1 second the right arrow on the Navigation button The call is placed on hold and other party receives audio from the System music source The User s GDC 450H receives dial tone form the system Note If a second call is waiting the above procedure automatically connects the waiting call To place another call 1 Press the End RS button the wireless terminal returns to an idle state 2 Place second call in the normal manner To retrieve the held call 1 Press and hold 1 second the right arrow on the Navigation amp button the held call is re connected 17 GDC 450H Wireless Handset User Guide 3 8 Call Transfer You can send an active call to another user of your LG Ericsson system You can announce the transfer to the receiving party Screened Transfer or without an announcement Unscreened Transfer To transfer an active call 1 Press the right arrow Navigation button the call is placed on hold and dial tone is received 2 Dial the number of the internal user to receive the call 3 To complete the transfer without announcement press the End Rem button OR 4 To announce the transfer await answer announce the transfer and press the End Rem button 3 9 Do Not Disturb DND When the
38. e deleted from a lost phone etc the following procedure may be used 11 GDC 450H Wireless Handset User Guide To Unsubscribe users locally in the system from the Attendant Station To unsubscribe all wireless terminals at once TRANS PGM 0 Flex Button 7 Password 147 HOLD SAVE 1 Press TRANS PGM button TRANS PGM LED flashes and MON LED lights steady 2 Press O 3 Press Flexible button 7 4 Enter the Password default 147 5 Press HOLD SAVE button and confirmation tone is heard 6 Confirmation tone or error tone will be heard at the Station and the corresponding Attendant Station To unsubscribe one subscribed wireless terminal TRANS PGM 0 Flex Button8 Station No HOLD SAVE 1 Press TRANS PGM button TRANS PGM LED flashes and MON LED lights steady 2 Press O 3 Press Flexible button 8 4 Enter the Station No 5 Press HOLD SAVE button and confirmation tone is heard 6 Confirmation tone or error tone will be heard at the Station and the corresponding Attendant Station To unsubscribe locally at the wireless terminal Menu BER button Select Phone Register menu Select Subscription d Select BASE to erase R C WR button for longer than 1 second OK a E RER button 1 Press Menu RER button 2 Main Menu is displayed on the LCD 3 Select Phone Register menu by pressing Navigation button and OK RH button 4 Phone Registe
39. ed calls You can enable or disable the display of this missed call message To enable or disable the missed call message 1 Select the Phone Setting menu from the User Menu Use the Navigation Gen button to highlight the Missed Call selection Press the OK MM left soft button to access the sub menu Use the left or right arrow of the Navigation button to select Yes or No Press the OK E left soft button to accept the date Press the End RS button ooo Ze 43 GDC 450H Wireless Handset User Guide 6 5 11 Range Out beep When out of range for more than a minute the phone will beep every 3 seconds If you expect to be Out Of Range for an extended period you should turn the handset power OFF lf for example you leave the office with the handset on the Out Of Range beep alerts you to turn the handset power OFF To disable the Out Of Range beep 1 Select the Phone Setting menu from the User Menu Use the Navigation button to highlight the Range Out beep selection Press the OK GMM left soft button to access the sub menu Use the left or right arrow of the Navigation GE button to select Yes or No Press the OK RER left soft button to accept the selection Press the End WE button oo So IS 6 5 12 Clock Display When a host system does not provide the handset with the date and time the handset clock display can be enabled and the date and time set The display can be enabled as outlined
40. ernal Ring Ring and Vib RINO age Ring after Vib 3 Phone Register Subscription A BASE 1 BASE 2 Base Choice S Modify PIN SE OO H BASE 4 PIN code A Phonebook Base ID Settings BEST BASE Reset Handset BASE 1 BASE 2 BASE 3 BASE 4 4 Appointment Daily Je h Daily Appoint A gt Text Appoint Monthly A gt Monthly Appoint Text Appoint Annual A gt Annual Appoint A Text Appoint 5 Phone Settings 4 Clock Date Time Alarm clock Yes No Time Keypad tones A gt Yes No Standard Display Always On Language Lighting Set Always Off Silent Mode Dialing Color an Sleep Mode A Yes No Keypad Lock da English Italian Spanish Yes No S W Version Russian Swedish Yes No Edit CO Code NG ae Yes No Missed Call Mode CODE RangeOut Beep CODE 3 Clock Display CODE 4 Auto Answer Mode A Vee No Yes No 6 Direct Call A7 Yes No gt Phone Number 50 51 GDC 450H Wireless Handset User Guide 52 GDC 450H Wireless Handset User Guide La N RTEL www lg nortel com
41. ertical lines indicate battery charge state At one 1 bar charging is ul recommended and call quality may be affected When low battery 1 bar backlight will be turn off to save battery power Common System and Handset Messages System Messages Message Description Display Duration Station number Idle state CALL FROM Station number of calling internal ae Alerting and active internal call STA XXXX user CALL TO Station number of called internal SE Alerting and active internal call STA XXXX user E Station number of waiting call Call on hold or transferring STA XXxXx LN XXX RINGING CO line number in host system Alerting LN XXX CO line number in host system Active external call NO CHANNEL No RF or system channel available Until a channel is available INVALID Station dialed is not valid About 30 seconds NO ANSWER STA XXX Called user does not answer About 30 seconds NO RESP Called station is not responding STA XXX perhaps power Is Off EE Handset Messages Out of range of a base station or not yet subscribed to a system Phone will not Out of range or not function Walls buildings and other subscribed obstruction especially large metal surfaces negatively impact useable range between the handset and Base station No Channel No available RF Channel in Base station All RF channels busy Range Out Silent Mode Alert mode IS vibrate no audible ring is Silent aiertmode provide in silent alert mode Locked c
42. es press the Speed Program EZA button twice 27 GDC 450H Wireless Handset User Guide For VS integrated basic mail or VM 3 party voice mail or UC integrated Unified Communications server messages dial 3 4 or 5 and follow the voice prompts to hear delete and manage your messages For MS internal SMS messages dial 6 and a summary of the text messages up to 10 are shown Dial the SMS number 0 10 to view the entire message To delete the SMS dial and 1 to cancel and return to idle dial and 2 to delete all internal SMS messages dial and 3 4 Press the End Ram button If you have responded to all your messages the message waiting indication is terminated 5 12 Blocking Outgoing Calls w Temporary COS As an alternative to the handset Keypad Lock you can block external calls from the handset employing the host system by activating Temporary Class of Service When Temporary COS is active the handset can make internal calls but cannot make external calls To activate Temporary COS and block outbound external calls Press the Talk Gem button you receive dial tone Press and hold 1 second the Speed Program Rn button Dial the Activate Temporary COS code default 21 Press and hold 1 second the Speed Program RE button Press the End Wm button oe To restore the normal COS and allow outbound external calls 1 Press the Talk Ben button you receive dial tone Press and hold 1
43. essaqe area zk Local message area Option Delete GDC 450H Icons Ilcon Name amp Description Antenna Icon T amp RSSI Icon ail The antenna icon indicates a DECT connection is established with the Base station The RSSI Received Signal Strength Indicator is a meter of the RF signal strength received by the handset The number of vertical bars 0 4 indicates the relative strength At less then 2 bars call quality may not be acceptable When no vertical bars are present there is insufficient RF signal to process signals and calls can not be placed or received Phone icon CR Indicates the handset is off hook talking or dialing and a DECT channel is established External Internal Call icon Indicates the call type external EXT or internal INT the host system Silent Alert icon qs Indicates the ringer in the phone is Off The phone will visual notify you of incoming calls and may alert you with the vibrator See Images amp Sounds in the User Menu section Message icon Indicates the system has at least one new message or callback message for the wireless terminal The message information is updated at 3 minute intervals GDC 450H Wireless Handset User Guide Keypad lock icon Indicates the phone dial pad and buttons are inactive This prevents accidental is buttons press as may happen with a wireless handset Alarm clock icon Indicates an Appointment is set E Battery icon Cd V
44. etting menu from the User Menu 2 Use the Navigation button to highlight the Language selection 3 Press the OK IE left soft button to access the sub menu 4 Use the left or right arrow of the Navigation button to select a language English Italian Spanish Russian Swedish 5 Press the OK MM left soft button to store the language selection 6 Press the End Rea button Note The selected language is used only for handset messages messages sent to the handset by the host system are displayed in the system language 6 5 6 Silent Mode You can set your phone for Silent Alerting the display and vibration will alert you of an incoming call Silent alert can be set in several ways from the Image and Sounds menu using the Silent Alert W button or the Silent Mode menu To use the Silent mode menu to set Silent Alert 1 Select the Phone Setting menu from the User Menu 2 Use the Navigation button to highlight the Silent Mode selection 3 Press the OK RR left soft button to access the sub menu 4 Use the Yes WE or No EM left or right soft button to adjust the Silent Alert setting Press the OK RER left soft button to store the alert mode 6 Press the End RS button i 6 5 7 Keypad Lock When the handset is carried in a pocket or purse buttons may be accidentally activated causing unexpected behavior Such accidental button presses may be circumvented by locking the ha
45. g call look up in the Phonebook If desired you can assign a CO access code the handset will send and receive in front of a Phonebook number for each separate zone For proper operation of the Phonebook your general CO line code should be used ex 9 or 0 Each of the four CO access codes is assigned to each of the subscribed systems CO Code 1 is for Base zone 1 CO Code 2 is for Base zone 2 etc If a code is not entered it must be entered as the first digit s of the telephone number in the Phonebook To assign a CO Code 1 Select the Phone Setting menu from the User Menu 2 Use the Navigation button to highlight the CO Code selection 3 Press the OK QM left soft button to access the sub menu 4 Use the left or right arrow of the Navigation button to select the code e Code 1 code for Zone 1 e Code 2 code for Zone 2 e Code 3 code for Zone 4 e Code 4 code for Zone 4 5 Press the OK RER left soft button to select the code number 6 Use the dial pad to enter a CO access code may be provided by System Administrator 7 Press the OK QM left soft button to store the setting 8 Press the End RS button 6 5 10 Missed Call Mode The missed call log is maintained by the handset In cases where the host system alerts multiple phones including your wireless handset and another phone answers the handset registers a missed call This may lead to a near constant display of xx miss
46. he OK RER left soft button 5 Select whether or not to use the CO Access code refer to Edit CO Code and press the OK RR left soft button Selecting the CO Access Code will insert the access code in front of the number during dialing The CO Access codes are entered in the Phone Settings menu discussed later in this guide 6 Enter the record number 1 60 using the dial pad and press the Save WM left soft button This will store the number as the record entered 4 3 Modifying Records in the Phonebook To modify a Phonebook record 1 Access the Phonebook menu as described above 2 Use the Navigation to highlight the Modify selection and press the OK RER len soft button 3 Use the Navigation button to locate the desired record and press the OK RW CS left soft button 4 Modify the Name telephone number CO access code use and the record number as detailed in the Adding Records to the Phonebook section 5 After modifying the record press the Save MM left soft button to store the modifications 4 4 Deleting records from the Phonebook To delete a record from the Phonebook 1 Access the Phonebook menu as described above 2 Use the Navigation to highlight the Delete selection and press the OK BS left soft button 3 Use the Navigation button to locate the desired record and press the OK RER left soft button 4 Press the Delete RR left soft button 5 Press the OK RR lef
47. hentication code AC available from your system Administrator Also before starting the subscription process make sure you are close to an active system Base station and the RSSI indicator is steady 10 GDC 450H Wireless Handset User Guide To subscribe to the system from the GDC 450H 1 Press the Menu RER button to display the menu 2 From the menu use the Navigation button to highlight Phone Register 3 Press the OK I button this displays the Phone Register menu 4 Select Subscription using the up and down arrows of the Navigation gt button and press the OK RW button 5 Select an available BASE station number and press the OK RER button the GDC 450H searches for the system displaying and Searching x When a system is found its RFPI is displayed The RFPI of your system is available from your System Administrator or perhaps the attendant 6 Press OK RR button while highlighting the RFPI to continue the subscription to the system or 7 Press No E button to continue the search 8 Enter your subscription Authentication code AC code is available from either your System Administrator or the attendant 9 Press OK RR button on successful subscription a confirmation tone is received at the GDC 450H and the Attendant Station 10 If the subscription fails repeat procedure from Step 3 to 6 at the Attendant Station and Step 1 to 8 from the GDC 450H refer to Note Note
48. hone register menu Press the OK RER left soft button Use the dial pad to input the current HS PIN Press the OK RER left soft button Use the dial pad to input the new HS PIN Press the OK RER left soft button Use the dial pad to input the new HS PIN again and press the OK RR left soft button 9 Press the End WA button El oh a oe Ze 6 3 4 Base ID For information purposes the handset can display the active zone To display the active zone 1 From the User Menu select the Phone Register menu 2 Select Base ID from the Phone register menu The active zone is displayed 3 Press the End RS button 6 3 5 Reset With the Reset sub menu you can clear the Phonebook Phone Settings or the handset settings Selecting Handset Setting clears the Phonebook Phone Settings Call Logs Direct Call number and all active subscriptions To use the Reset sub menu 1 From the User Menu select the Phone Register menu 2 Select Reset from the Phone register menu The Reset sub menu is displayed Phonebook clears the Phonebook and Direct Call number Settings Phone Settings returns Phone Settings to default values Handset clears the Phonebook call logs active subscriptions and the Direct Call number and resets the Phone Settings Use the Navigation button to highlight a selection Press the OK RER left soft button PIN request will display Use the dial pad to enter your PIN Press the
49. ive call is placed on hold and the new call is connected 5 5 Linked Stations Pairs Your handset may be linked to another station in the host system When linked operation of the two stations is synchronized when one is busy the other is busy and when one is in DND the other is in DND Either can activate and deactivate user features 23 GDC 450H Wireless Handset User Guide Note The system may take up to 3 minutes to notify the handset of changes to the state of user features such as DND A linked station will display IN USE AT LINK when the other linked station is in use on a call 5 6 Answering a Call Ringing at Another Station When another station rings and you may be allowed to answer pick up the call There are two 2 types of pick up directed call pick up answers a call to a specific phone and group pick up answers a call to a group of phones To pick up a call for a specific ringing station 1 Press the Talk Sep button you receive dial tone 2 Dial the Directed Call Pick up code default is 7 3 Dial the number of the ringing station To answer a Call to a group of ringing stations 1 Press the Talk Sep button you receive dial tone 2 Dial the Group Call Pick up code Refer to your System Administrator or perhaps the Attendant for the dial code Note In certain situations such as private line calls callbacks etc you will not be permitted to pick up a ringing call 5 7 Using Station S
50. ive dial tone 2 Dial the Call Forward code default 554 3 Dial the Call Forward type code 0 Follow me forward 1 Unconditional forward 2 Busy forward 3 No answer forward 4 Busy or No answer forward 5 9 Off net forward check with your System Administrator Cancel call forward 4 Dial the internal destination station group etc 5 Press the End RS button e gt gt gt ad 25 GDC 450H Wireless Handset User Guide Note When forwarding calls to voice mail assure you have created a voice mail greeting In some cases such as Follow me forward you must enter an Authorization Code to activate the feature DND and Call Forward are mutually exclusive features If DND is active Call Forward cannot be set You must have allowed Call Forward in the host system for Call Forward to be available at the terminal 5 10 Pre defined amp Custom Text Messaging You can select a text message to be shown on the display of a calling station When active incoming intercom callers see the text message in the phone s LCD There are ten Pre defined messages 01 10 ten system wide Custom messages and one User Custom Message Several of the ten Pre defined messages allow for auxiliary information such as a time date or number as shown in the chart below To activate call forward for your calls 1 ao Ot ee ZS Press the Talk Be button you receive dial tone Press and hold 1 second the Speed Progra
51. le state then select a number to dial from the redial list and the make the call by pressing the button Note Using a noise canceling or unidirectional Ear Microphone Headset with an impedance below 1 KQ usually is 1 2 2KQ may cause abnormal operation unit may self answer without pressing the button when an incoming call is received and unit may hang up unexpectedly while using the Ear Microphone Headset GDC 450H Wireless Handset User Guide Warning 1 Do not insert any external substance except ear microphone for GDC 450H in the hole Inserting anything except for ear microphone provided by general maker may cause severe damage to the terminal 2 Be careful no to let any foreign materials get into the product In particular if a staple and pins are magnetized on the receiver make sure to eliminate it before use Using it in such condition may casue fire electric shock or injury especially on the face 1 1 2 GDC 450H Display The GDC 450H has a large 128 x 128 pixel full color TFT LCD Liquid Crystal Display The display indicates the status of the handset and provides visual feedback for dialing and other actions Various icons detailed in the chart below are shown at the top of the display The central area of the display shows messages from the host LG Ericsson system and the phone itself At the bottom are selections for the Left and Right soft buttons Idle mode Active call mode Call Time 00 01 o System L ARA m
52. le under the Image selection of this sub menu To view and modify the wallpaper shown in the handset display 1 Select the Image and Sound menu from the User Menu select the Image Press the Option left soft button to display the log Options Use the Navigation button to highlight a selection View shows the available wallpaper images Set selects the displayed image as the handset wallpaper 5 Press the OK QM left soft button to access the sub menu 6 Press the End Ra button aN 6 2 2 Sounds In the Sound sub menu you can select the ring tone or melody for internal and external calls as well as the ring volume level Also the alerting mode can be set with the Ringing Mode selection under this sub menu Under the Sound sub menu are three selections Internal Ring External Ring Ringing Mode To set the internal or external ring options 1 Select the Image and Sound menu from the User Menu 2 Select the Sound 3 Press the OK RR left soft button 4 Use the Navigation button to highlight a selection Internal Ring External Ring Press the OK RR left soft button to access the sub menu 6 Press the Option QM left soft button to display the Internal and External Ring Options 7 Use the Navigation button to highlight a selection Ring Type Volume 8 Press the OK Ri left soft button to access the sub menu Si 35 GDC 450H Wireless Handset Use
53. lor for all digits dialed To adjust any of the Display characteristics 1 Select the Phone Setting menu from the User Menu 2 Use the Navigation button to highlight the Display selection 3 Press the OK RER left soft button to access the sub menu 4 Use the left or right arrow of the Navigation button to select the display characteristic e Dialing color e Lighting Set Press the OK RER left soft button to store the setting For dialing color use the left or right arrow of the Navigation button to select Yes ER left soft button or No RER right soft button For back lighting use the Navigation Q button to select the desired option e Standard back light turns Off 20 seconds after last button press e Always On back light is always ON e Always Off back light is always OFF e Sleep Mode back light turns OFF 20 seconds after last button press backlight and handset turns OFF after 1 minute 7 Press the OK RR left soft button to store the setting 8 Press the End RS button DO Note To conserve battery charge use the Standard or Sleep backlighting mode At low battery levels less than two bars the backlight turns OFF until the handset batteries are re charged 6 5 5 Language The GDC 450H supports multiple languages you can select one of for languages for use in the display of handset messages 41 GDC 450H Wireless Handset User Guide To select a language 1 Select the Phone S
54. m BEER button Dial the Text Message code default 51 Dial the message number Dial any additional information required by the message Press and hold 1 second the Speed Program EZA button Press the End WA button Message Code Message Description User Custom Message a 96 D Telephone No up to 17 digits os MEETING TILL mhm 09 AT HOME LD AT BRANCH OFFICE CancelMessage _ S To create a User Custom Message N E Ee Press the Talk Be button you receive dial tone Press and hold 1 second the Speed Program EZDA button Dial the Text Message code default 52 Dial 0 0 Dial the message content using the 2 digits for each character method see chart below Press and hold 1 second the Speed Program EPA button Press the End Rm button 26 GDC 450H Wireless Handset User Guide 5 11 Responding to a Message Wait Indication Your system supports a number of message formats including station callback message and voice mail Depending on the host system and configuration you may receive missed external call messages and internal Short Message Service SMS When a message has been left you receive a message waiting icon When you respond to all outstanding messages the icon disappears There are two primary message wait response procedures one for the ipLDK and one for the iPECS Check with your System Administrator to determine the correct operation for
55. nd WE button 5 14 Call Park Call Park is commonly used with paging and is used to transfer a call to someone not at a known station The call is parked and the desired party paged to answer the parked call The paged party dials the park location known as an orbit to answer the call To park an active external call 1 Press the right arrow of the Navigation E button the call is placed in parking hold 2 Dial the Park orbit code see your System Administrator for codes 3 Press the End RS button 4 Page desired party To answer a park call from idle 1 Press the Talk IEAA button you receive dial tone 2 Dial the Park orbit code see your System Administrator for codes 3 After the confirmation tone a private connection is established to parked call 4 When done press the End Rm button 5 15 Conference Room GDC 450H cannot initiate a conference It can however create join and delete a conference room To activate create a conference room 1 Press the Talk 433 button you receive dial tone 2 Press Speed Program button longer than 1 sec and dial 53 conference room activate code Room Number 1 9 3 Enter optional 5 digit conference room password as needed 4 Press right arrow of the Navigation E button longer than 1 sec To deactivate delete a conference room 1 Press the Talk Sep button you receive dial tone 2 Press Speed Program button longer than 1 sec a
56. nd dial 54 conference room delete code Room Number 1 9 3 Press right arrow of the Navigation button longer than 1 sec To join a conference room 1 Press the Talk Sep button you receive dial tone 2 Dial 59 conference room join code conference room number 1 9 3 If enabled enter the 5 digit conference room password 29 GDC 450H Wireless Handset User Guide 5 16 Universal Night Answer In the Night mode the host system changes assigned incoming call routing often to alert through external speaker systems Universal Night Answer UNA permits you to answer such ringing calls at night To use UNA to answer a call 1 Press the Talk Ben button you receive dial tone 2 Dial the UNA code see your System Administrator for the UNA dial code 3 After the confirmation tone a private connection is established to the caller 4 When done press the End RW button 5 17 Using the System Alarm Clock In addition to the handset Appointment feature the host system incorporates a wake up or alarm clock feature When the alarm time is reached The system alerts you with ring signal and displays WAKEUP RING The wake up call is effective for one day or until canceled repetitive To set the wake up time Press the Talk EBJA button you receive dial tone Press and hold 1 second the Speed Program RH button Dial the Set Wake up code default 41 Dial the Wake up time as hh mm in 24 hour f
57. ndset keypad The keypad can be locked using the Lock gp button or using the Phone Settings menu To use the Phone Settings menu to lock the handset buttons 1 Select the Phone Setting menu from the User Menu 2 Use the Navigation button to highlight the Keypad Lock selection 3 Press the OK IWE left soft button to access the sub menu 4 Use the Yes EEE or No RER left or right soft button to adjust the lock or unlock the handset buttons 5 Press the OK MM left soft button to store the selection 6 Press the End Ra button Note When locked the display will show Keypad locked While locked the only allowable operation is unlock All other buttons are ignored if pressed and calls cannot be placed 42 GDC 450H Wireless Handset User Guide 6 5 8 S W Version For maintenance purposes you can request the GDC 450H display the handset software version To display the current software version of the handset 1 Select the Phone Setting menu from the User Menu 2 Use the Navigation button to highlight the S W Version 3 Press the OK GMM left soft button to access the sub menu The S W version displays 4 Press the End jag button 6 5 9 Edit CO Code The GDC 450H can subscribe to four 4 DECT zones simultaneously Each zone may have access to a different set of external lines with different codes The code is used to place calls from the handset Phonebook as well as for incomin
58. ng burning plug off power or phone line Call for service center If left intact for long time it may be a cause of fire or electric shock GDC 450H Wireless Handset User Guide Do not let water into the phone or get wet If do power off and plug off phone line Keep it dry Precipitation humidity and liquids contain minerals that will corrode electronic circuits Call for service center If use It intact it may be a cause of an electric shock Be careful of antenna or corner of the phone It may be a cause of an accident or injury lf there are foreign matters or dampness on the charger wipe it with a soft cloth If left intact it may be a cause of breakdown Do not drop or throw the phone If do and something wrong plug off and call for service center It may be a cause of an accident injury or breakdown Do not drop an object It may be a cause of breakdown Do not put your ears on the speaker It may be a cause of an accident or injury Do not put driver or pincette into the phone It may be a cause of fire or breakdown Do not wrap the phone with vinyl It may be a cause of coating peeling off GDC 450H Wireless Handset User Guide GDC 450H Wireless Handset User Guide Table of Contents t Ia dee e Te de EE 1 1 1 DE COL OM DEES 1 Er IMO SOU EE 1 Ek GBA RR EEN 4 ti Ghargerpase E EE 6 2 Getting Started WEN 7 2 1 Unpacking the GDGC 4A30 Fersan EEE acs T 2 2 Installing the batteries AA 8 2
59. on 3 4 Enter the station s name using two 2 digits for each character Refer to the Dial the Name Program Code default is 74 character entry chart below Up to 7 characters can be entered Press and hold 1 second the Speed Program IEZA button to store the information Press the End Raa button The wireless terminal goes to an idle state Eo Ee eh Pace ae spans ooo eto eee eee 4 40 5 5 0 6 60 7 7 0 8 80 9 9 0 5 2 Request a Busy Station Call Back lf you receive busy tone when calling another station you may request to be placed ina queue to receive a Call Back When the called station returns to idle the system signals you with Callback ring When you answer the now idle station is called To activate a callback 1 While receiving internal call busy tone press the asterisk ESCH button you will receive confirmation tone 2 Press the End Rm button The wireless terminal goes to an idle state 22 GDC 450H Wireless Handset User Guide When the busy station returns to idle you receive a Callback 1 Answer the callback in the normal manner 2 Await answer from the previously called station Note A maximum of 5 simultaneous callbacks can be active Call backs are returned in the order received at the Station your callback may not be first in line If you do not answer a callback ring within 15 seconds the callback is cancelled 5 3 Leaving a Return Call Message When a
60. ormat 2359 Press for a repetitive alarm otherwise a one time alarm is set Press and hold 1 second the Speed Program EZDA button Press the End RS button oe E To set the wake up time Press the Talk MEEA button you receive dial tone Press and hold 1 second the Speed Program BEER button Dial the Cancel Wake up code default 42 Press and hold 1 second the Speed Program ERDA button Press the End WA button Ore aN S 5 18 To Register a System Access Authorization Code PIN For certain operations the host system may require you enter a System Access Authorization code or Personal Identification Number PIN These codes are used to prevent unauthorized use of external system resources and to end Temporary COS You must create your PIN prior to attempting to activate Temporary COS or accessing restricted facilities To create or modify your System PIN 1 Press the Talk Sep button the dial tone will be heard 2 Press and hold the Speed Program ERR button for 1 second 3 Dial the Auth Code select to Modify dial code as needed ask your System Administrator for codes 4 Press and hold the Speed Program ERR button again for 1 second 5 Press the End RS button 30 GDC 450H Wireless Handset User Guide Note Depending on the host system an Authorization code initially may be set as the station number Also the number of digits may vary for different host systems refer
61. peed Dialing In addition to the Phonebook numbers the host system provides memory for additional Speed dial numbers Once stored these numbers can be accessed and dialed Each of the Station Speed dial numbers can be up to 24 digits in length and may include special instructions including as 1st digit Activate Display Security do not display number Flash as 1st digit Activate dial tone detect F Insert a pause dialing command not 1st digit Switch from Pulse to DTMF dialing msg callbk send as ISDN Keypad Facility IE hold Insert a Pulse to tone switch over To store a Station Speed dial number Press the Talk EEA button you receive dial tone Press and hold 1 second the Speed Program IQ button Press the Speed Program EPA button Dial the Speed dial bin location may be obtained from System Administrator Dial the CO Access code may be obtained from System Administrator Press and hold 1 second the Speed Program EZDA button Dial the phone number to store Press and hold 1 second the Speed Program EZA button If desired enter a name to associate with the number Refer to the Programming a Name into Display section earlier in the guide 10 Press and hold 1 second the Speed Program ERDA button 11 Press the End Rm button Repeat the above procedure to store additional Speed dial numbers oS EE eg 24 GDC 450H Wireless Handset User Guide To delete a Station Speed
62. r Guide For Ring Type 1 Use the left and right arrows on the Navigation S button to hear each ring tone 2 Select the Set RW left soft button to select the tone 3 Press the OK RW left soft button to confirm the selection 4 Press the End RS button For Volume Use the left and right arrows on the Navigation S button to adjust the volume Select the Set RW left soft button to select the tone Press the OK RW left soft button to confirm the selection Press the End Rm button koa oi In the Ringing Mode sub menu you select the alerting mode of the handset The mode can be set to provide audible ring vibrate combinations of ring and vibrate or visual ring LED flashes only To set the Ringing Mode 1 Select the Image and Sound menu from the User Menu 2 Select Sound 3 Press the Option RER left soft button to display the log Options 4 Use the Navigation button to highlight Ringing Mode 5 Press the OK IE left soft button to access the sub menu 6 Use the left and right arrows on the Navigation S button to select an option as below By Ring audible ring and LED flashes No Sound LED flashes only By Vibrator handset vibrates and LED flashes no audible ring Ring and Vib audible ring vibrate and LED flash simultaneously Ring after Vib handset vibrates for 10 seconds then audible ring LED flashes 7 Select the Set GEM left soft button to select the tone 8 Pre
63. r menu is displayed on the LCD 5 Select Subscription by pressing UP DOWN button and OK QM button 6 Select BASE number to erase and press R C Wb button for longer than 1 second 7 Press OK I button to confirm erase 8 If local unsubscription is completed phone returns to previous menu 2 Authentication Verifies the wireless terminal and or the user with the System The User inputs the User Personal Identification UPI or Authorization code PIN 5 digits when requested by System Attendant To Authenticate a User from the Attendant Station 12 GDC 450H Wireless Handset User Guide TRANS PGM O Flex Button 5 Station No HOLD SAVE 1 Press TRANS PGM button TRANS PGM LED flashes and MON LED lights steady 2 Press O 0 in ipLDK 24 100 300 300E 3 Press Flexible button 5 4 Enter a station number to be authenticated 5 Press HOLD SAVE button and confirmation tone is heard To Authenticate a User from the Wireless Terminal When the attendant presses HOLD SAVE a message asking for User j authentication will be displayed on the wireless terminal along with an audible ZS confirmation tone PIN 5 digit 1 Enter five digit Authorization code PIN 2 Press OK QM button longer than 1 second Confirmation tone or error tone will be heard at the Station and the corresponding Attendant Station 2 8 Registering GDC 450H to LWS BS LG Ericsson
64. ration from LWS BS Unsubscribing will make a wireless terminal lose connection to the LWS BS To unsubscribe a wireless terminal it should be in an idle state To Unsubscribe from the LWS BS 1 Press Menu button 2 Press Digit 1 CONFIGURATION submenu or Select 1 CONFIGURATION using Navigation up down key and OK Button 3 Press Digit 4 STATION REGISETR submenu or Select 2 DEREGISTER using Navigation up down key and OK Button 4 Press Digit 2 DEREGISTER submenu or Select 2 DEREGISTER using Navigation up down key and OK Button 5 Select phone number using Navigation left right key S101 S107 Press Navigation OK button or OK soft key 7 When the unsubscribing is completed below message is shown on LWS BS LCD STATION 10X UNSUBSCRIBED SUCCESS SS 14 GDC 450H Wireless Handset User Guide Note e DEREGISTER You want to erase registration information of both Base Station LWS BS and Wireless terminals GDC 450H FORCED ERASE You want to erase registration information of the relevant Wireless Terminal e g in case that the terminal is OFF or missed In this case the registration information will be kept on the terminal itself All Data ERASE You want to erase registration information of all wireless terminals In this case the registration information will be kept on the terminals themselves Procedure of erasing the registration information on the terminal itself 1
65. ry level surface Keep the Charger base away from the edges of the surface to avoid the potential of a fall Avoid situations where you might drop the handset While the GDC 450H is a rugged mobile device dropping it on to the floor may cause critical damage Locate cables to avoid potential for damage For example do not place under rugs or carpet as damage may result from foot traffic or heavy objects Also do not locate cables between the desktop and walls where they may be crushed damaging the insulation Check cables regularly and if damage is noted disconnect your phone Contact your local representative for a replacement Should liquid spill on the handset remove the batteries and dry with a soft cloth Do not use during lightning storms Lightning presents a potential shock hazard Clean the GDC 450H with a soft dry cloth do not use liquid cleaners Always use caution when connecting to AC power Use only with a properly grounded standard AC power outlet What is new in this release Jee Date Change of Contents April 2010 Initial Release July 2010 Updated New Cl GDC 450H Wireless Handset User Guide Important Safety Information Read this information before using your phone Failure to comply with these guidelines could prove either dangerous or illegal This information helps avoid damage to the phone personal injury or property damage This section provides A After reading user guide retain it for next u
66. s shows caller id number and time of call Save to Phbk stores the number as a record in the Phonebook requires name entry Delete deletes record Call calls number 5 Press the OK RER left soft button to access the sub menu 6 Press the End RS button Options under the delete selection allow you to delete all records in a specific call log or all records in all the logs To delete records in a log or all logs 1 Select the Call Register menu from the User Menu 2 Select the Delete sub menu 3 Press the Option RECH left soft button to display the log Options 4 Use the Navigation O button to highlight a selection Missed calls Received calls Dialed calls All Calls 5 Press the OK QM left soft button to select the log Press the OK QM left soft button again to delete the records 7 Press the End RS button D 34 GDC 450H Wireless Handset User Guide 6 2 Image amp Sound In the Image and Sound sub menu you select a wallpaper to display on the handset and adjust internal and external ring Selections for this menu are Images Sounds To select an item from the Image and Sound sub menu 1 Select the Image and Sound menu from the User Menu 2 Use the Navigation button to highlight a selection 3 Press the OK Ri len soft button to access the sub menu 6 2 1 Images The handset includes several wallpapers that can be viewed and selected with options availab
67. se About Installation and Using Environment various safety guidelines According to manual install the phone If not it may not work or life span diminish Do not install in the place where shine on the rays of the sun or on the carpet or cushion It may be a cause of fire or breakdown Do not install in the ill ventilated place such as desk or etc It may be a cause of fire or breakdown Do not install near a bath kitchen table humidifier rice cooker wind and rain or damp area It may be a cause of an electric shock fire breakdown or transformation Do not put things near phone as flower vase flowerpot cup cosmetics medicine or water It may be a cause of fire or electric shock GDC 450H Wireless Handset User Guide Do not put the phone on shaking shelves or slant place It may drop and broke down or get hurt Do not install the phone near appliance such as tv refrigerator vacuum cleaner audio and etc It cause harmful interference to make noises Do not install the phone in dusty area It may be a cause of fire or electric short Do not install the phone near vibrating area It may affect phone quality and life span Do not plug many power cords in outlet It may be a cause of fire or electric shock Do not touch the plug with wet hands When disconnect the power cord of any accessory grasp and pull the plug not the cord It may be a cause of fire or electric shock GD
68. ser Menu with the handset idle 1 Press the Menu fa left soft button 2 Use the Navigation button to highlight a selection 33 GDC 450H Wireless Handset User Guide 3 Press the OK GM left soft button to access the sub menu 4 Press the Back RR right soft button to return to the previous menu The following sections provide details on each of these menu selections 6 1 Call Register Call Log The Call Register maintains a log of up to 100 calls to and from the handset including missed calls There are four selections in this sub menu Missed Call logs incoming calls not answered by the handset Received Call logs incoming calls answered by the handset Dialed Call logs calls placed from the handset Delete Call deletes records in a log or all logs To select an item from the Call Register sub menu 1 Select the Call Register menu from the User Menu 2 Use the Navigation button to highlight a selection 3 Press the OK RER left soft button to access the sub menu Options for each of the logs Missed Received and Dialed include view details save to the Phonebook return call and delete the record To access options for a log 1 Select the Call Register menu from the User Menu 2 Select the desired call log Missed Received or Dialed 3 Press the Option RER left soft button to display the log Options 4 Use the Navigation button to highlight a selection Detail
69. ss the OK E left soft button to confirm the selection 9 Press the End Ra button Note You can quickly set the Silent Vibrate alert mode with the Silent Alert button A 6 3 Phone Register To register a new wireless terminal to your base or to register a wireless terminal again after base reset refer to the Section Base Reset 1 Press the Menu BER button to display the User menu 2 From the User Menu use the Navigation button to highlight Phone Register 3 Press the OK GMM left soft button This displays the Phone Register menu Subscription Base Choice Modify PIN Base ID Reset gt o 36 GDC 450H Wireless Handset User Guide 4 From the Phone Register menu select Subscription using the up and down arrows of the Navigation button and press the OK WE button 5 Select an available BASE station number and press OK J button The GDC 450H searches for the system displaying and Searching x When a system is found the corresponding Radio Fixed Part Identification RFPI is displayed verify the RFPI with the System Administrator or Attendant 6 3 1 Subscription In order to obtain services from a base station or zone the handset must establish a subscription with the zone The handset may subscribe to four 4 base stations or zones simultaneously When subscribing to the system you will need the RFPI and Authorization code which may be available from your Sy
70. ssure the handset is locked to a Base button nothing happens J station and RSSI is at least two 2 bars 46 Terminate the subscription and re Subscription error subscribe OO GDC 450H Wireless Handset User Guide Specifications Standard DECT GAP Frequency band 1880 1900MHz RF Modulation GSFK Range from Base Station to Handset Maximum 200 meters Typical 0 meters GDC 450H Wireless DECT Handset Item Specification Battery Life Talking Mode 20 hours Standby Mode 150 hours Charge Time 6 hours Type DC 3 7V 950mAn Li ion Programmable Ring Internal External ring each 9 kind Type Display feature Icon 10 Type LCD 65K color TFT system Refer to System manuals GDC 450H Charger Base ltem Specification 1 AC DC Adaptor AC 100V 240V 50 60Hz 0 2A input ACDC Adapior Be SAV 700mA3 57VA output e GR Operating temperature 0 40 C 47 GDC 450H Wireless Handset User Guide 9 Dial pad Character Charts The integrated GDC 450H Phonebook permits names to be associated with a Phonebook record The following charts provide the correlation between the dial pad digits and characters Charts are available for English Italian Spanish and Russian To insert a character each dial pad button is pressed one or more times to select the desired character English Language Character Chart 8 9 10 ca 7 BS K 0 Yo WW LG KS EX E ER Ea l ER RI DN KA
71. stem Administrator Also before starting the subscription process make sure you are in range of the desired zone and the Received Signal Strength Indicator RSSI indicator is steady showing at least 2 bars To subscribe to a system from the GDC 450H 1 Verify that Press the Menu RER button to display the menu 2 From the menu use the Navigation button to highlight Phone Register 3 Press the OK Oo left soft button to display the Phone Register menu 4 Select Subscription using the up and down arrows of the Navigation button and press the OK IEE button 5 Select an available BASE number up to 4 and press the OK RER button the GDC 450H searches for the system and displays Searching x When a system is found its RFPI is displayed verify with your System Administrator or the Attendant 6 Press the OK IE button to subscribe to the system RFPI shown Press No button to continue searching 7 Enter the Authorization code available from the System Administrator as needed 8 Press the OK RER button confirmation tone will be heard is received at the GDC 450H and the Attendant s LCD will display Subscription Done 9 Press the End Ga button If the subscription fails repeat above Steps 3 6 from the Attendant Station and Steps 1 8 from the GDC 450H Note According to the system or radio channel environment the system or the wireless terminal periodicall
72. t soft button to confirm the deletion 4 5 Searching the Phonebook with Find To search the Phonebook for a record 1 Access the Phonebook menu as described above 2 Use the Navigation to highlight the Find selection and press the OK RW left soft button This will display the Find Record menu below View Modify Delete 3 Search the Records by 21 GDC 450H Wireless Handset User Guide a Enter the first few characters of the name using the dial pad See the charts in the Appendix Dial pad Character Charts As an example press 5 twice for kK and 3 twice for e to search for kenny b Press the Find MM left soft button to display matching records When the record is KA press the Call RW right soft button to dial the number OR Press the Find RER left soft button to search all records Use the Up and Down arrows on the Navigation O to highlight the desired record When the desired record is located use the directions under Modifying Records in the Phonebook or Deleting Records from the Phonebook sections 5 Using Advance System Features 5 1 Program a System User Name You can store a name in the host system for use as your id when you are called or call another station The User name is also employed with Dial by Name To assign your User name de Press the Talk Bep button you receive dial tone 2 Press and hold 1 second the Speed Program EZA butt
73. t the same time details described in Terminating a Subscription Q The second method is to unsubscribe locally in the system or at the wireless terminal separately A Warning If a user terminates their subscription at their terminal the Attendant should be notified so terminal information can be deleted from the System 2 6 Subscribing the GCD 450H to a System Prior to accepting a connection with a GDC 450H a subscription to services must be entered into the WMI of your telephone system This is accomplished in a two step process the Attendant station enables subscription of a phone to the system then the GDC 450H subscribes to the system for services 2 6 1 Enabling Subscriptions To enable a subscription from the Attendant station Press Trans Pgm button the Pgm LED flashes and the Monitor Speaker LED lights Press 0 and Press Flexible button 1 Dial the subscribing station number Enter the Phone Type 3 for new systems or 1 for older systems pre 1 0B s w Pres Hold Save button When the subscription completes a confirmation tone is received and then press Monitor Speaker button ea eS Note Don t press Monitor or Speaker button at the Attendant phone until the GDC 450H completes the subscription and subscription confirmation tone is heard 2 6 2 Subscribing to the System When subscribing to the system you will need the system s unique Radio Frequency Personal Identification RFPI and the System Aut
74. tion 1 1 1 Handset The GDC 450H shown in the Handset Diagram appears much like a mobile cell phone On the front are the dial pad a number of control buttons described in the Handset Buttons and Features list and a large LCD display In the lower rear of the unit is the battery compartment The battery charging terminals are located at the bottom of the unit On the left side of the GDC 450H is the headset jack Earpiece Full color LCD Left Soft Right Soft button button Talk button a P Kan zm Navigation End Power UNS button button i Call back __ D A Speed Program Message button ES A ii d button 6 eo G Recall Clear Dial pad button Agen S Silent Alert K r Keypad Lock button button Handset Diagram GDC 450H Wireless Handset User Guide Handset Buttons and Features Button Description Navigation button Left arrow idle state view missed call other states left navigation Right arrow Idle state place call host intercom dial tone active call state press to Transfer call or press and hold 1 second to place call on hold in User Menu right navigation Up and Down arrows Idle state Up for Local redial Down for Phonebook menu active call state adjust audio volume in User Menu up and down navigation Left amp Right soft button Interactive menu displayed directly above buttons Selection varies as needed To select press the soft button
75. utton 10 Press the End RS button Once an appointment is set you can modify the time When you select the Appointment menu you can select from the sub menu to view modify or delete the appointment To view modify or delete an appointment 1 Select the Appointment menu from the User Menu 2 Use the Navigation button to highlight a selection Modify Date Modify time Delete View Text 3 Press the OK i left soft button to access the sub menu 4 Use the dial pad to enter the date or time 5 Press the OK i left soft button to store new date and time 6 Press the End Ra button 6 5 Phone Settings Under the Phone Settings menu are various sub menus associated with characteristics of the handset In total there are 13 items under Phone settings as below Clock Alarm clock Keypad Tones Display Language Silent Mode Keypad Lock e gt gt gt 39 GDC 450H Wireless Handset User Guide S W Version Edit CO Code Missed Call Logging Range Out beep Clock Display Auto Answer Mode e d To select an item from the Phone Settings sub menu 1 Select the Phone Settings menu from the User Menu 2 Use the Navigation button to highlight a selection 3 Press the OK GMM left soft button to access the sub menu 6 5 1 Clock Date and Time display When a host system does not provide the handset with the date and time the handset clock display can be enabled and the d
76. ws of the Navigation button to highlight the volume level and press the OK Ri button 3 3 Muting your Microphone During a call you can mute the microphone so that the connected party can not hear what is said in your vicinity While the Mic is muted you will still hear the connected party To mute the microphone while on a call 1 Press the Option GM left soft button The handset displays the Call Options menu 2 Use The Up and Down arrows of the Navigation gt button to highlight Mute and press the OK Q button MUTED is shown in the display To deactivate Mute so that the connected party can hear you 1 Press the Enable RW right soft button the function is deactivated 3 4 Placing an Outside Call While the phone is idle you may dial a call up to 24 digits The display indicates the last 11 digits dialed In case an error occurs during dialing you may delete the last or all digits using the delete BER right soft button Pressing the button deletes the last digit holding the button pressed for more than 1 second deletes all digits To Place a call 1 Dial the phone number remember you may need to dial an access code such as 9 to place an external call 2 Press the Talk Gem button the Phone icon CS displays and the number dials 7 You alternatively can press the Talk EEA button prior to dialing In this case when you press the button you will receive a dial tone and may then di
77. y may not recognize that the system has the subscribed wireless terminal or the wireless terminal is subscribed to the system Once a user has performed the subscription procedure try to make a call first Then if a user can t make a call try to subscribe the wireless terminal again after verifying the terminal is unsubscribed described in the following chapter It is recommended all other DECT systems be disabled while performing the Subscription procedure 6 3 2 Selecting a DECT Zone While the handset may subscribe to four zones simultaneously the handset can only be active in one You may select the active Base station to control the zone in use If not already registered to the base you can subscribe for services from the zone To change the active zone 1 From the User Menu select the Phone Register menu 2 Select Base Choice from the Phone register menu 37 GDC 450H Wireless Handset User Guide 3 Use the up down arrows on the Navigation button to select a Base 1 4 or Best Choice 4 Press the OK RER left soft button This handset searches for the selected zone and displays Searching x when located the idle mode display is shown and services are available 5 Once the base is found it is an active base 6 3 3 Modify PIN The Handset PIN Authorization code can be changed default 0000 To change the H S PIN 1 From the User Menu select the Phone Register menu select Modify PIN from the P

GDC-450H - MBC - Business Communications

Contents

Download Pdf Manuals

Related Search

Related Contents