Pros`s Pro Electronic TX-500N Stringing Machine User`s Manual
Contents
1. After stringing turn the machine off Turn the tension on the display down to 10 kilogram that the tension in the machine is as little as possible in the time of not stringing Fixing of the Racket Loosen both mounting stocks place the four K shaped side supports into the hole of the side support arms in the far outer hole for tennis rackets in the other hole for badminton and squash Now place the racket in the middle of the stringing machine Be aware that the two string clamps can reach all the stringing area of the racket Never apply excessive force or over tighten the mounting stock locking knobs this will damage the parts Tighten now the side support arms and the mounting stock but be careful not to do this too heavily that the racket will not be deformed Very Important How to put the string into the tensionsystem First place the string over the small reel and then around the big one and place it into the slot and hold the string down Then push the button to 1 and the machine starts pulling until it has the right tension Adjust the Base of the Swivel Clamp to the correct holding pressure If the Clamp base is no longer working very well put the clamp base vertical to the track Insert the 3mm Allen wrench into the hole on the side of the base before you have to remove the black cap Then turn it clockwise only slightly do not use excessive force this could damage the base It can be very difficult2. Pros s Pro Electronic TX 500N Stringing Machine User s Manual Unpacking and inspection The machine is delivered ready assembled In the parcel are 4 pieces V shaped Side Supports two Ultimate clamps one AC power cord and Allen wrenches Lift carefully the machine out of the carton Inspect the Electronic TX 500N stringing machine for obvious damage Check 1f all parts are in the carton If any item is missing or damaged contact your delivery agent and your sales representative Retain the packaging materials and shipping container in the event that reshipping is required Operating Instructions n Place the machine on a table or a stand foot On the electronic part is on the back side a switch which should be in the ON position for normal operation Turn the power on and a red light flashes and the tension number appears on the LED display Select the scale of the Tension for kilograms or pounds left beside the display The machine is always shipped with kilogram selected Now turn the knob on the right side of the Electronic part to select the tension you want to string your racket The machine is very sensible so it will by maybe not so easy to select The stringing machine has 3 positions TT Machine Stops een ere Machine tears to the selected tension yee Machine moves back to the starting position If the string is not release then press the green button the machine will rotate one total round
3. do turn Then put the Allen wrench out of the base and test if it is working well again if not repeat the process again So you do not have to adjust on the base of the clamp base Only at this screw Maintenance a o po 8 9 The Electronic TX 500N stringing machine is adjusted and calibrated before shipment Working is easy and relatively maintenance free Keep the stringing machine always at a dry and safe place Keep it away from dust grease moisture and any type of heat Clean the dust and other dirt with a soft cloth or brush Water should never come inside the machine Do not use liquid cleansers abrasive cleaners or aerosol cleaners Use fine emery cloth to remove the wax buildup from the jaws of the clamps and the string gripper Do not uses sandpaper to remove the wax buildup it will destroy the special finishing Do not lubricate the tracks of the turntable Do not use penetrating oils to clean or to lubricate 10 Check the clamps often to be sure that they hold the string properly I not adjust them as shown before 11 Reset the tension setting to 10 kilograms after stringing Troubleshooting The power light does not shine and the electronic part does not do anything e Be sure the power switch is in on position e Check that the power cord is properly installed e Check the fuse Turn off the power switch and unplug the power cord from the wall outlet before checking the fus
4. e The fuse housing is next to the power switch e Check the wall outlet with another electronic equipment The string clamp does not hold the string e Clean the jaws of the string clamp e Adjust the clamp on the top The string slips through the string gripper e Clean the string gripper like described before The clamp does not move smoothly or can not be fixed e Clean the tracks of the turntable e Adjust the swivel clamp base per instruction The tension pulling is not correct e Calibrate the machine e Is the string not fixed in the clamp e Is the clamp base moving Calibration The machine is calibrated with an electronic Tension calibrator if you have only a mechanic one please be sure that it is not too old otherwise the spring inside Will give you wrong results 1 Set the tension to 25 kg 2 Fix the tension calibrator with one end at the mounting post and the other into the string gripper 3 Start pulling and check the result on the tension calibrator 4 If the result is not correct you have to readjust the machine 5 Beside the display are two little holes take a small screwdriver put it into the upper hole and turn inside a little to get the same tension at the display and the tension calibrator At the beginning it will be not so easy because there is a transport protection on it 6 Then pull again and check the result 7 Tf the result is ok it is finished if not repeat this procedure as long a
5. s the result is ok
Download Pdf Manuals
Related Search