130 mW red/green DMX laser User manual
Contents
1. TAO 130 mW red green DMX laser ITA i a if Sy F e LED j J mom N f ns j 4 N MIC J 1 N A area VOL i MAX F _ Ps K 2 L Visible or invisible radiation avoid eye or skin C RoHS A oe exposure to direct or scattered radiation WY User manual Safety precautions WARNING This unit may cause serious injury to eyesight when used incorrect It therefore is strongly advised to read this user manual carefully to get familiar with the functions of this laser device WARNING This unit must be operated by or under the supervision of an adult This device is not Suitable for children WARNING Do not look directly into the beam coming out of the lens from short distance or when a solid beam is projected This may cause serious injury to eyesight Ayra is not responsible for any injuries Caused by incorrect use of this device WARNING Do not project the beam of this unit on to reflective surfaces as the shattering beam may Cause injury to eyesight Installation requirements Always check the voltage settings on the unit and the power supply you want to connect the device to If the voltage requirements do not mee2. it may cause severe eye damage possibly resulting in permanent visual loss 1 2 3 4 5 6 Device overview H Power supply Power IN and Power OUT Connect the device to a power supply with the provided cable DMX in output When using a DMX controller connect the device with the supplied XLR cable The unit has a XLR in and output for the distribution of DMX signals LED indicator LED indicator for the music activated mode Microphone Built in microphone for the music activated mode Microphone sensitivity Variable setting of the microphone sensitivity use a small screwdriver to change the sensitivity from low to high DMX dipswitch Use these dipswitches to change the operating mode or select a starting address for the DMX mode Setting up the device Setting up the device When the power supply is connected the unit will first calibrate the stepping motors of the unit It is normal that this may cause any noise When the calibration is done the unit is ready to be used in the selected DMX automatic or music controlled mode It is possible that the unit may shut off the beam projection when no music or sound is detected This will avoid the projection of a solid static beam which may cause injury to eyesight This unit uses stepping motors to create variable movements to the laser beam This way figures and patterns can be made The unit uses high speed steppi
3. g As present program gt Auto Active The laserrun preset program 6 DMX 512 laser under control by DMX 512 Controller Square patterntest Dot drawing test DMX operating mode While in the DMX mode it is possible to select the working mode of the laser That way you can either choose to use your own programmed presets of your DMX controller or to activate the music activated automatic working mode of the laser to have a fully automatic lasershow Depending on the starting address you selected earlier the laser responds to the following commands In this example we use DMX starting address 1 When you use a different DMX starting value for example 29 the unit will respond from channel 29 30 31 and so on For more information about DMX consult the manual of your DMX controller or software DM X 512 Value Function Music active mode Select 1 25 patterns Reverse rotation speed Patten horizontal rotation position X rotation speed Pattern vertical Y rotation position vee Patten horizontal Pattern vertical Enlarge speed from fast to slow Zoom in speed from slow to fast TYPE ITA 01 MKII Laser diode green class 532 nm gt 30 mW red class 3B 650 nm gt 100 mW Scan type stepping motors Scan motor angle maximum angle 25 degrees Working modes automatic full automatic laser show with built in program music activated full automatic laser show
4. ng motors to create the moving beams of the laser It is normal that the laser beam and projection may appear flickering when projecting large or complex patterns The projected beams of the unit may appear shivering when projecting complex or large patterns on surfaces as a wall ceiling or decorative cloth With the use of a red and green diode the creation of yellow orange beams is possible in mid air However severe shaking collision and rough installing procedures may cause the optics of the laser to move slightly thus separating the beams Selecting a working mode This laser device has three working modes which are automatic music controlled and DMX To select the right operating mode for your situation use the dipswitch panel on the rear of the unit A DMX dipswitch panel works with a binary character It sends 0 or 1 message to the electrical circuit To select a working mode pay close attention to the information scheduled below Every DMX dipswitch stands for a certain value which is on or off The values are stated as below 1 1 2 2 3 4 DECIMAL BINARY USAGE OF DIP SWITCH 4 8 LSB MSB an 0 000000000 6 32 7 64 1 100000000 8 128 9 256 14 011100000 10 mode switch DMX ON OFF 511 111111111 To select the different working modes pay close attention to the setting of DMX dipswitches below Music Active With the change ofmusic rhythm the effect of laser will change accordin
5. re the beam exit and fan are not blocked by any objects in the near environment This unit must be connected to a grounded power supply that meets the voltage requirements of the device Maintenance and protection Keep the unit away from dusty environments as this may have negative effect on the fan cooling system and laser optics Ayra recommends using a flightcase for storage of this device Clean the optics and fan of the laser with a small soft brush and vacuum cleaner when needed Clean the housing of the unit with a damp cloth WARNING Always disconnect the unit from the power supply when cleaning the unit Reconnect the unit only if any moist on the fixture disappeared completely This laser device is a lighting effect designed to support visual entertainment while playing music Continuous use is not recommended Do not use the device longer than 3 hours subsequently so the unit can cool down This will provide a longer lifespan for the diodes Apply a cooling down time of 25 minutes before re activating the laser Do not switch the power on and off too often as this may cause serious damage to the unit Avoid heavy shocks and collision during transport and use as this might cause damage to the laser diodes electronic circuit optics and housing Keep the device away from moisture rain water or any liquids as this may cause a short circuit and or electric shocks If any liquid enters the unit power supply or housing of
6. t do not connect the device as this may cause serious damage This device must be installed by a professional technician in a standing or hanging position Always pay attention to the positioning of the unit as the beams may project directly into your audience It is strongly advised to NOT project the beams directly into your audience Ayra strongly recommends a minimum distance of 1 5 meters in height between the lowest projected laser beam and your audience for optimal safety If there is no other option keep a minimum distance of 5 meters from the beam exit to the first beam that hits your audience When installed in a standing position a safety cable is recommended to secure the unit Ayra recommends to use the bracket when installing the unit on a flat surface by mounting it with a proper bolt into the surface it is placed on When installed in a hanging position this unit MUST be secured by using a safety cable capable of holding 10x the weight of this device When installed in a hanging position this unit must be mounted to a proper surface e g a truss system When using a truss system Ayra recommends the use of a proper hook or halfcoupler Make sure there are no flammable objects in the direct environment of the device such as decorative objects Keep a minimum distance of 1 5 meter Do not block the beam exit and fan Keep a minimum distance of 0 5 meter from any walls to provide sufficient cooling Make su
7. the unit disconnect the unit immediately and do not reconnect the power supply Contact your local dealer or technician to inspect the unit for any damage IEC in out power supply Connect several units by using the provided IEC to Schuko cable It is possible to link multiple ITA devices but after 10 units the connection to the main power supply must be renewed Also don t combine the power link function of ITA units with any other devices especially not with devices that consume lots of energy such as fog machines active speakers etc Box contents Box contents 1x laser device 1x user manual 1x IEC to Schuko power cable Unit and accessory inspection Always use the supplied power cable to connect the unit to a power supply If the cable appears broken or has visible damage do not use it The supplied cable can be replaced with a regular IEC to Schuko cable with a minimum cable diameter of 0 75m2 If the unit will not be used for a longer period of time disconnect it from the power supply and store it in a dust free environment Always check the unit for possible damage before use If you suspect that something is wrong with the unit do not connect it to a power source When you suspect that your unit is broken or damaged contact your local dealer or a certified technician to inspect the unit When your device does not generate any laser beams do not look directly into the lens When the laser suddenly produces a beam
8. with built in program responding to the beat of music DMX 9 channels input signal bandwidth 0 1000 Hz environment temperature 10 35 degrees Celsius netto weight 2 kg dimensions 260 x 170 x 120 mm Built in patterns K a gt 1b Address Green laser diode Electrical diagram Red laser diode QL stepping motor Laser dicde power supply Transformer Power switch 110V AC IN
Download Pdf Manuals
Related Search