Omega Manual
Contents
1. UT ID Lo SHOTG UN SUPPRESSOR HARVESTER BIG BORE 338 HARVESTER 30 OMEGA SAKER 762 2000 SAKER 556 0000 OLORON 200 SAKER K 556 SPECWAR 762 SPECWAR 556 SPECWAR 556 CENTERFIRE RIFLE SUPPRESSORS 45 W 5 3412345 SilencerCo cz 1 Sy X ANVLOO A 3 5 6 A34dSO Ss Gv A34dSO RIMFIRE SUPPRESSORS PISTOL SUPPRESSORS Field Manual x O O gt Thank you for choosing to add SilencerCo suppressor to your collection We love what we do and take pride in the products we produce because of this there is no greater joy than knowing others are experiencing the results of our passion and hard work So go out and enjoy your new suppressor after reading the manual of course and thank you for choosing SilencerCo Sincerely and Silently Joshua Waldron SilencerCo Co Founder amp CEO Note If you have any questions whatsoever about whether you are performing the assembly disassembly or cleaning of the suppressor properly and in accordance with these instructions you may contact SilencerCo customer service by phone at 801 417 5384 or via email2. W at SilencerCo hope that you enjoy the technological advancements offered by the Omega sound suppressor To provide for your safety and the effective use of this suppressor it is critical that the owner and any user of the suppressor read this entire manual and follow strictly the warnings and instructions within This suppressor is intended to be used only by those who are well versed in the safe operation of firearms MANUFACTURER S DISCLAIMER SilencerCo is not responsible for improper usage of this product This product is potentially dangerous and as such it is the user s responsibility to understand and implement its proper use If you do not understand the instructions in this manual please contact SilencerCo for further clarification at 801 417 5384 SONIC CRACK The Omega is designed to suppress the initial muzzle blast and subsequent projectile de corking pressure The Omega does not contact or otherwise interact with the projectile allowing the projectile to travel at its default velocity When using supersonic ammunition a sonic crack is produced by the projectile as it breaks the sound barrier Depending on the geography of the area the sonic crack may vary in volume This is solely a function of the projectile breaking the sound barrier and is not related to suppressor performance WARNING Failure to follow installation and maintenance instructions detailed in this manual may result in serious personal
3. at info silencerco com For a list of available mounts and suppressors visit WWW SILENCERCO COM O 2014 SilencerCo LLC All rights reserved The contents of this publication may not be reproduced in any form or by any means in whole or in part without the prior written permission of the copyright owner PROTECT YOUR RIGHTS PROTECT YOUR HEARING The American Suppressor Association is fighting to protect and expand your suppressor rights Join the fight today Become a member at www ASAMEMBER com Contact us at info americansuppressorassociation com TWITTER COM SILENCERCO Find Us Online FACEBOOK COM SILENCERCO SILENCERCO YOUTUBE COM SILENCERCO
4. injury and damage to the weapon Firearm sound suppressors are user attached firearm muzzle devices and as such are subject to improper attachment issues unless the procedures outlined in this manual are followed precisely Do not attempt to use this product unless you have specific training and experience in the use of firearms Before installing or removingthe Omega sound suppressor from the host weapon be sure thatthe weapon is unloaded and the action is opened so that it is visibly clear of any ammunition If you at all unsure as to the proper procedures to ensure that your firearm is unloaded please consult your firearm user s manual instructions and contact a properly licensed dealer or the manufacturer of your weapon Because suppressed firearms make less noise than unsuppressed firearms it is easy to forget that they are still firearms and capable of causing bodily injury and property damage It is of vital importance to remember that a suppressed firearm is just as dangerous as an unsuppressed firearm and that the same safe handling requirements still apply When removing the Omega use extreme caution as it may be hot to the touch after firing Use gloves to avoid burns or other injuries Check the fit between barrel and suppressor before firing The thread mount must be fully shouldered on the barrel There should be no visible gap between the barrel shoulder and the face of the suppressor thread mount If there is any gap
5. DO NOT fire the host with the suppressor attached Poor accuracy and product damage may result if the suppressor is not fully shouldered Assembly and disassembly should never be performed while the suppressor is affixed in any manner to a host firearm Always completely remove the Omega from the host firearm before assembly and or disassembly is attempted Before performing maintenance removing or installing the suppressor open the action ensure firearm is unloaded and be sure the chamber is empty Failure to do so can result in property damage injury or death MADE IN THE USA The Omega is shorter lighter and quieter than any other centerfire rifle suppressor on the market In addition to its performance the Omega s design allows for maximum user adaptability and convenience Each Omega comes with a 5 8x24 direct thread mount a quick detach Active Spring Retention ASR mount complete with a Specwar ASR muzzle brake and an Anchor Brake All other accessories including additional muzzle devices and endcaps are sold separately The Omega is rated for a range of ammunition from 22 Hornet to 300 Winchester Magnum The Omega is rated down to 10 barrels for 223 Remington 5 56 NATO 16 barrels for 308 Winchester 7 62 NATO and 20 barrels for 300 Win Mag Note Suppressors must be free of obstructions such as mud dirt etc Do NOT attempt to shoot through an obstructed suppressor The Omega was designed to be used dry and fr
6. arbon or fouling If necessary run a cleaning brush through the bore to remove any light fouling of the suppressor Note Do not run cleaning patches through the bore as the patches might become lodged in the suppressor and cause damage upon firing Caution Always read the warning label on any cleaner or solvent and remember that virtually all solvents are inherently dangerous and potentially toxic Always use adequate ventilation and both skin and eye protection when using solvents LIMITED LIFETIME WARRANTY LIMITATIONS TO WARRANTY THIS WARRANTY DOES NOT COVER DAMAGE TO THE SUPPRESSOR OR THE HOST FIREARM RESULTING FROM CARELESS OR IRRESPONSIBLE HANDLING ADJUSTMENTS OR MODIFICATIONS TO ITS DESIGN NEGLIGENCE OR OTHER ABUSE SILENCERCO ASSUMES NO LIABILITY WHATSOEVER FOR UNSAFE USE OF THE SUPPRESSOR OR ILLEGAL USE BY ITS PURCHASER OR ANY OTHER PERSON THAT COMES IN CONTACT WITH THE PRODUCT AFTER PURCHASE SILENCERCO ASSUMES NO RESPONSIBILITY FOR PHYSICAL INJURY OR PROPERTY DAMAGE RESULTING FROM CARELESS OR IRRESPONSIBLE HANDLING AND OR USE OR BY ANY USE CONTRARY TO THE RECOMMENDATIONS WARNINGS AND CAUTIONS GENERALLY LISTED IN THIS MANUAL SILENCERCO DOES NOT COVER DAMAGE TO THE SUPPRESSOR OR THE HOST FIREARM RESULTING FROM IMPROPER HAND LOADED RELOADED AMMUNITION OR DEFECTIVE AMMUNITION REPAIR POLICY Should the silencer require repair or modification the owner should contact SilencerCo either in writing or by telephone Many probl
7. ee of any ablative media such as grease and water If submerged in water the user must allow a minimum 6 second drain time after exiting water ASR MOUNT MUZZLE BRAKE SAKER BASIC TOOL HARVESTER BIG BORE MULTITOOL INIA PRODUCT SPECS INCLUDED The Omega ships with the attached direct thread mount and Anchor Brake as well as an Active Spring Retention ASR quick detach mount and muzzle brake included in box All tools required for installation and removal are included MOUNTING OPTIONS Whether you prefer the simple shorter nature of a direct thread setup or the quick attach detach features of the ASR Mount you should take care to ensure that the Omega is mounted securely to your firearm before firing These instructions will help to prevent the problems and dangers that can arise from improper seating DIRECT THREAD MOUNT ATTACH SUPPRESSOR TO FIREARM After confirming that your firearm is unloaded place the threaded end of the Omega in line with the threads of the barrel 2A Taking care not to cross thread screw the suppressor onto the barrel until it is firmly secured and no additional barrel threading is visible To remove from host reverse these instructions Hand tighten only REMOVAL AND INSTALLATION OF DIRECT THREAD MOUNT Hold the Omega body 1A with a firm grip and use the t
8. ems can be handled without having to return the product If it is determined that the product needs to be returned for repair or modification contact SilencerCo customer service 801 417 5384 to obtain an RMA number Do not return the suppressor to SilencerCo until you have contacted customer service as an RMA code must be provided If repairs are required due to a defect in manufacturing or materials there will be no charge for repairs Subject to any restrictions set forth herein SilencerCo agrees to replace and or repair the Omega for an unlimited amount of time This warranty covers repair service and replacement of damaged product caused by normal use free of charge only if performed SilencerCo facility Should a silencer require repair the owner must contact SilencerCo and make arrangements to return the product Customer must return damaged product with a legible copy of the approved ATF form and a legible written description of the problem defect and or malfunction Please include in written description the serial number of the product and the events leading up to the issue including what ammunition has been used and any host weapons that have been used If SilencerCo determines at its sole and absolute discretion that a returned suppressor is not covered under this warranty for any reason you may purchase a replacement product at 75 off the suggested retail price SALVO 12
9. hree pegs of the Harvester Big Bore Multitool 3A in a counter clockwise direction to loosen the coupler from the bottom of the suppressor To install reverse these instructions starting the thread by hand to avoid cross threading MOUNT 01 The ASR Mount is proprietary mounting system and as such requires acomplementary muzzle brake included Note Crush washers are NOT recommended as they do not crush uniformly and WILL cause improper mounting and baffle strikes SilencerCo recommends the use of a peel washer or the included shim kit if any indexing of the mount is required For proper alignment it is essential that the muzzle brake seats against a 90 barrel shoulder The flash hider muzzle brake should be torqued to 20 30 ft lbs Use of Rocksett or Loctite Red 271 is recommended PEEL WASHER CRUSH WASHER DO NOT USE ASR MOUNT 02 E Step 1 Thread the ASR Mount 1B assembly onto the Omega suppressor body 2B by hand taking care not to cross thread Step 2 Hold the Omega body 2B with a firm grip Using the Saker Basic Tool 3B to grasp the notches in the base of the ASR mount 18 tighten the coupler in a clockwise direction Torque to approximately 35 ft lbs MUZZLE DEVICE 01 Step 1 Remove your existing muzzle device using a 3 4 open end wrench Remove the crush washer from barrel threads Step 2 Install the muz
10. zle brake 1 by threading it onto barrel 2C Use the provided shim kit to ensure proper muzzle brake alignment Tighten onto barrel using a 3 4 open end wrench Use of Rocksett or Loctite Red 2717 is recommended to secure the muzzle brake MUZZLE DEVICE 02 Note Verify the ASR collar 1D is in the unlocked position with locking collar rotated clockwise before installing Step 3 Installthe Omega 2D by sliding the back end over the muzzle brake until it stops then turn the suppressor 2D clockwise to hand tighten Step 4 Rotate the ASR collar 1D counter clockwise to the locked position To remove perform steps three and four in reverse order UNLOCKED LOCKED To remove Anchor Brake 1E from the Omega 2E line up the three pegs on the Harvester Big Bore Multitool 5 with the holes on top ofthe brake Holding the suppressor with a firm grip rotate the tool counter clockwise until the brake is removed To install Anchor Brake perform steps in reverse order startingthe thread by hand to avoid cross threading Warning Firing the Omega without the Anchor Brake or a SilencerCo endcap will negate benefits of using a suppressor and will void the warranty MAINTENANCE The Omega typically requires limited maintenance Mounts should periodically be cleaned with any standard gun cleaning solvent and a brush to remove any c
Download Pdf Manuals
Related Search