Handles Accessory Installation Instruction Sheet
Contents
1. CHRISTIE Handles Accessory Installation Instruction Sheet INTRODUCTION Use the following instructions when installing the Handles Accessory Kit to Roadie 25K projectors The handles are designed to provide a sturdy method of lifting and transporting the projector a short distance With the optional Rigging Clamp Kit available separately the handles can be used for hoisting or rigging a single projector Without the need to remove any covers installation of the handles accessory is relatively straightfor ward Accessing the bottom of the projector is the only requirement KITS REQUIRED e Handles Accessory Kit 113 101101 01 includes handles and 4 bolts for installation e optional Rigging Clamp Kit 113 102101 01 required for hoisting rigging SAFETY AND WARNING GUIDELINES A A Always unplug the projector prior to installation and servicing A This procedure must be completed by qualified personnel only A Four or more people can lift and hand carry one projector a short distance using the handles A Never use the handles to carry hoist rig a stack of projectors A Never exceed the load rating specified for the handles A Please read all instructions before you begin installation Handles Accessory Installation Instruction Sheet 1of4 020 100131 01 Rev 1 08 07 CHRISTIE INSTRUCTIONS 1 ELEVATE THE PROJECTOR Install safe supports under both ends of the projector so there is approximately 12 clearance over the f2. dditional two safety straps Using one safety strap per crossbeam route the strap through the 2 bottom eyebolts and bring them up and around the outside of the handles Use 4 bottom eyebolts to secure an additional two safety straps Route safety straps through bottom BOTTOM VIEW eyebolts and up around handles Shown without clamps in place for clarity Figure 5 Secure Projector with Safety Straps 5 Install the projection lens and secure it with it s safety ring and tether strap Figure 6 See also the User Manual for more lens installation details lt lt eae AX warnine ecure For all flown projectors Cable Ends Figure 6 Secure Lens with Ring Clamp and Tether 4of4 Handles Accessory Installation Instruction Sheet 020 100131 01 Rev 1 08 07
3. ith load capacity adequate for the total weight of the projector and handles when lifting hoisting Never exceed the load rating specified A WARNING When flying a single projector using the handles the overhead truss must have a minimum load rating of 1925 Ib 873kg Support structure truss must comply with applicable local codes An inadequate truss may cause serious injury or death When hoisting rigging a single projector using the handles do the following 1 Remove projector lens 2 Clamp the 4 rigging clamps to the projector s handles staying within the assigned rigging zones shown in the figure below Maintain swivel Allow 12 inches between clamps for proper stability Make sure rigging clamps can swivel freely do not tighten the cross bolt of the clevis arm NOTE Symmetrical placement of the clamps on each side of the handles is strongly recommended See Figure 3 and Figure 4 Figure 3 Install Rigging Clamps Handles Accessory Installation Instruction Sheet 3 of 4 020 100131 01 Rev 1 08 07 CHRISTIE A WARNING Critical Safety Minimum of 4 rigging clamps required for a single projector Always use redundant safety straps and cables Observe load ratings and all applicable local codes when hoisting rigging a projector between clamps BOTTOM VIEW Figure 4 Rigging Zones 3 Secure the other end of each clamp to the primary support structure Secure the projector with an a
4. loor or other stable surface Do not lift at the center Ay T M m A WARNING Do not lift at the center of the projector The bottom panel of the projector may crush and damage internal components 2 ALIGN HANDLES Orient handles so that when installed the FRONT label aligns with the end of the front of the projector With two people supporting the projector carefully slide handles into position lifting the projector off the blocks as needed to position handles within the channels at the bottom Figure 1 Align Handles 3 SECURE HANDLES Using the four bolts provided in the Secure handies lt Albait kit secure the handles to the bottom of the projector Bottom View Figure 2 Secure handles 2of4 Handles Accessory Installation Instruction Sheet 020 100131 01 Rev 1 08 07 CHRISTIE USING HANDLES TO HOIST RIG A SINGLE PROJECTOR You can safely hoist and or suspend a single projector by its handles using the rigging clamps available separately in the Rigging Clamp Kit 113 101101 01 Read the following safety warnings before hoisting rigging ONE projection head A WARNING Remove the projection lens before hoisting rigging a projector A WARNING Use the projector s handles for hoisting rigging ONE projector only Never use the handles to carry hoist rig and stack of projectors A WARNING Maximum load rating of handles is 385 lb 174 63kg Use straps and or cabling w
Download Pdf Manuals
Related Search