Fibridge - FBSWITCH1000 Series Operators Manual
Contents
1. L Fibridge FBSWITCH1000 User Manual 3 Check if the link partner port is working in the same mode as that of the current port 3 Failure LINK ACT LED of fiber optic port is off after self test with the port connected Solution C1 Check if the fiber is connected correctly 2 Failure connection of transmit or receive side may lead to the port link status led off So need to check if the TX or RX connection of the fiber port is normal 4 Failure Data transfer abnormally including transferring failure data loss Solution 1 Gheck if the transmit power of the fiber optic port is normal 2 Be sure no single mode fiber connected with multi mode equipment 3 Check if they are used in pairs when single strand devices are used 5 Failure The device doesn t work after working well for a while That is to say the device doesn t transfer data but if reset it will work normally Solution It is usually caused by the Ethernet switch In normal status the switch will take CRC and package length check and drop the bad package However some bad ones could not be inspected and thus they could not be sent out or dropped so these bad packages will be stored in the buffer one by one until the buffer is filled up which brings about the failure of the switch Try to connect the device with PC directly to see if the failure is not existed PAGE 14 L Fibridge FBSWITCH1000 User Manual 10 Order information 10 12. Available for Managed Type 7 1 RS 232 Management Port Baud Rate 9600 115200 Data Width 8 Odd Even Paritv None Stop Bit 1 Flow Control None Connector DB9 Male 7 2 Twist pair Management Port Link Speed 10 100Mbps auto negotiation Duplex Mode Auto negotiate on half full duplex mode Connector RJ45 PAGE 12 L Fibridge FBSWITCH1000 User Manual 7 3 Default User and Password Name admin puser guest Password No Password 7 4 Default IP Address The default IP address of the device 192 168 0 216 8 Installation 1 Connect the fiber strand and twist pair cable according to the practical application environment then connect the device to power supply 2 Switch on the power the device will perform the self test procedure During the test all LEDs will blink one by one 3 After self test if the ports connect well the PWR and LINK ACT LED will light on The 100M LED is on while link speed is 100Mbps on corresponding port and the FDX LED is on while the port works in full duplex mode 4 While transmitting or receiving data LINK ACT LED blinks 9 FAQ Failures amp Solutions 1 Failure Power LED is off Solution Check up the device if the power cable is connected correctly 2 Failure LINK ACT LED of twist pair port is off after self test with the port connected Solution 1 Check if the twist pair cable is connected correctly 2 Check if the link partner is running normally PAGE 13
3. 220VAC power supply F6 2114 S3043CA Four twist pair ports and one fiber optic port Managed type single mode 1550nm transmission wavelength 40Km single strand SC fiber optic connector 220VAC power supply lt F6 2105A Five twist pair ports Managed type 220VAC power supply lt F6 2005D Five twist pair ports Unmanaged type 48VDC power supply PAGE 16
4. Environment 2 Working environment Temperature 5 C 40 C Humidity 30 90 25 C Atmosphere pressure 86 kPa 106 kPa lt Store and transportation environment Temperature 20 C 60 C Humidity 20 90 25 C Atmosphere pressure 86 kPa 106 kPa PAGE 7 Zj Fibridge 5 Appearance 5 1 F6 2114 V1 2 1 Front Panel FBSWITCH1000 User Manual DFibridge AccessLink LA A S S S Gr o GOOLOJjik Management Management LEDs for Twist pair Fiber Port Port Ethernet Ports Optical Twist pair Console Ports Port General LEDs Reset Button 2 Rear Panel 220VAC 48VDC Power Jack Power Jack 5 2 F6 2014 F6 2114 V2 1 1 Front Panel Fibridge Cum O O O O Omen x fix qr O 22220 DOODOr Axesslink LC Sa AIO ki 29998x IL IL IL MDH LINK DTESTEM NS RESET WLAN 1234 Management Management LEDs for Twist pair Fiber Port Port Reset Ethernet Ports Optical Twist pair Console Button Ports Port General Switch for LEDs VLAN PAGE 8 fFibridge FBSWITCH1000 User Manual 2 Rear Panel 220VAC 48VDC Power Jack Power Jack 5 3 F6 2005 F6 2105 V2 1 1 Front Pan
5. f Fibridge FBSWITCH1000 User Manual Version 2 0 Beijing Fibridge Co Ltd L Fibridge FBSWITCH1000 User Manual CONTENT i Jar OHIO enee ak az kni inunan EEN 3 2 a LI l A aiana u anaiena 4 2 1 Hardware Function eter eee 4 2 2 Software Functon 2 5 3 Interface Specification sssssseeeennnnnneneena 6 3 1 Fiber Interface Specification 6 3 2 Ethernet Port 7 A 12 1 l a A RO A 7 4 1 Device Gze 7 42 D TEE 7 4 3 Environment nn 7 AppeaPant i SEENEN 8 5 1 F6 2114 V1 2 eener rererere 8 5 2 F6 2014 F6 2114 V2 1 L 8 5 3 F6 2005 F6 2105 V2 1 LL 9 5 4 LEDs Function Description 10 5 5 DIP Switch and Reset Button Function Description osaan EES EA iiia 11 Typical Applications ssemma 12 7 Management Port Configuration 12 7 1 RS 232 Management Port 12 7 2 Twist pair Management Port 12 PAGE 1 F Fibridge FBSWITCH1000 User Manual 7 3 Default User and Password 13 7 4 Default IP Address 13 8 INSTAN ANON xi Sean Sege d Geh ENER SEENEN tenn 13 9 FAQ Failures A Solutions sssssseeneeneni 13 10 Order Intormatton ne 15 10 1 Model i iii ea at 15 10 2 Part Number P N eter eees 15 PAGE 2 L Fibridge FBSWITCH1000 User Manual 1 Introduction Beijing Fibridge Co Ltd summarized the experience of selling the American broadband products since 1995 and synthesize
6. management software e Adopt the centralized management style and the tree view catalogue which can manage many sets of device at the same time in a single window FBSWITCH1000 User Manual 3 Interface Specification 3 1 Fiber Interface Specification Only Available for F6 2014 F6 2114 1 Adopt standard 1 9 pin optical transceiver module 2 Wavelength 850nm or 1310nm in multi mode and 1310nm or 1550nm in single mode 3 Upto 120km transmission distance in single mode 4 SC ST FC optical connectors are selectable Optical Power Budget List Wavelen Connector Transmit Sensitivity Satura Max Loss gth Type Power dBm tion Dist dBm nm dBm dBm Km Km MM850 SC ST 14 31 34 14 2 3 18 5 MM1310 SC ST 14 31 34 14 5 2 18 5 SM1310 SC ST FC 6 15 Better 3 40 0 4 than 34 SM1310 SC ST FC 3 3 Better 3 80 0 4 than 36 1550 SC ST FC 3 3 Better 3 120 0 25 DFB than 36 L Fibridge FBSWITCH1000 User Manual 3 2 Ethernet Port 1 Fully compatible with IEEE 802 3 IEEE802 3u and IEEE802 3x Standards 2 Link speed 10 100Mbps auto negotiation 3 Duplex mode Half full duplex auto negotiation 4 Connectors RJ45 Jack 5 Support automatic MDI MDI X crossover 4 General 4 1 Device Size 252mm Width x 135mm Depth x 36mm Height 4 2 Power AC 100 240VAC 50 60Hz DC 48VDC Power consumption lt 5W with full load 4 3
7. Model FBSWITCH1000 5 port Ethernet Switch Bandwidth Access 10 2 Part Number P N lt gt F6 2114 S3042CA Four twist pair ports and one fiber optic port Managed type single mode 1310nm transmission wavelength 40Km double strand SC fiber optic connector 220VAC power supply F6 2014 S3082CA Four twist pair ports and one fiber optic port Unmanaged type single mode 1310nm transmission wavelength 80Km double strand SC fiber optic connector 220VAC power supply F6 2114 S3042CD Four twist pair ports and one fiber optic port Managed type single mode 1310nm transmission wavelength 40Km double strand SC fiber optic connector 48VDC power supply F6 2014 S3042FA Four twist pair ports and one fiber optic port Unmanaged type single mode 1310nm transmission wavelength 40Km double strand FC fiber optic connector 220VAC power supply F6 2114 M31CA Four twist pair ports and one fiber optic port multi mode Managed type multi mode 850nm transmission wavelength double strand SC fiber optic connector 220VAC power supply F6 2114 M32CD Four twist pair ports and one fiber optic port multi mode Managed type multi mode 1310nm transmission wavelength double strand SC fiber optic connector 48VDC power supply F6 2114 W3042CA Four twist pair ports and one fiber PAGE 15 L Fibridge FBSWITCH1000 User Manual optic port Managed type single mode 1310nm transmission wavelength 40Km single strand SC fiber optic connector
8. d the merits of different products of the world famous manufacturers The series of products select the higher quality device and develop meticulously for use This series of products are orientated in the broadband access system for its high quality high stability and low price After being put up the products can be used in the telecommunication IP MAN broadband optical network solution for its steady performance and powerful function It interconnects a main board server repeater hub switch or PC and another PC simply The device adopts the elaborately designed switch core with high speed non blocking fabric and ultra broad switch bandwidth to make sure data transmission and reception has high stability As an Ethernet access device the device not only supports IEEE802 3 10Base T Ethernet and IEEE802 3u 100Base Tx fast Ethernet protocols but also is compliant with IEEE 802 3x Flow Control IEEE802 1Q VLAN TAG IEEE802 1p Qos and IEEE802 1D Spanning Tree protocols FBSWITCH1000 Series Network Switch provides four standard RJ45 jacks as 10 100Mbps Ethernet ports and one SC FC ST connector as fiber optic port or five standard RJ45 jacks as 10 100Mbps Ethernet ports FBSWITCH1000 series have two types managed and unmanaged The managed type supports WEB management SNMP software management and RS 232 console management Customers convenientiv view and configure all ports and management part via management software PAGE 3 L Fibri
9. dge FBSWITCH1000 User Manual including the function of enable disable a certain port setting the port force mode link speed duplex mode and ports speed limitation and resetting the management part all 5 Ethernet ports or both Some functions such as VLAN Port Mirroring and Broadcast Protection are very convenient and useful for high level application More information about SNMP management software please read FBSWITCH1000 Series Fi View AL Software User Manual for reference 2 Features 2 1 Hardware Function e Four Twist pair ports and one Fiber Optic port F6 2014 F6 2114 series and five Twist pair ports F6 2005 F6 2105 series available Support 10Base T 100Base TX 100Base FX Fully compatible with lIEEE802 3 Ethernet and IEEE802 3u fast Ethernet protocols e Support IEEE802 3x flow control protocol e Support IEEE802 1D Spanning Tree protocol e Non blocking switch core provides high speed forward performance e High speed MAC address lookup table inside stored up to 1K MAC addresses e Upto 1916 Bytes packet forwarded e Up to 5km transmission distance on multi mode optical port and 120km transmission distance on single mode optical port e Twist pair ports support MDI MDI X auto crossover PAGE 4 L Fibridge FBSWITCH1000 User Manual e Low power consumption low heat generation and excellent compatibility e Single strand dual strand optical module selectable FC SC ST optical port selectable 2 2 Software F
10. eceiving data OFF Port not linked Port Dupl ON Full duplex FDX Green FS P Mode OFF Half duplex 100M G Port Link ON 100Mbps reen Speed OFF 10Mbps PAGE 10 L Fibridge FBSWITCH1000 User Manual 5 5 DIP Switch and Reset Button Function 1 Description Reset Button FBSWITCH1000 provides an embedded reset button in front panel to prevent being triggered by mistake Tipping the reset button with a pin softly the device will be reset During reset LEDs of Ethernet ports will blink sequentially which means the device is performing self test DIP Switch The 2 bit DIP switch resides in the front panel is used to enable disable VLAN functionality for the unmanaged type device When 2 bit set to OFF the simple port based VLAN is disabled and all of the five Ethernet ports are switched While 2 bit set to ON the simple port based VLAN is enabled and each of port 1 2 3 and 4 sets up a VLAN between itself and port 5 respectively that means port 1 2 3 and 4 can send package to or receive package from port 5 but can not between any two of them Notice this DIP Switch is only available for UNMANAGED type device PAGE 11 L Fibridge FBSWITCH1000 User Manual 6 Typical Applications Manageme nt PC A FBSWITCH1000 Media Converter Cc ali IR fm IR User 3 User1 to User4 can apply necessary bandwidth and connect to the WAN using FBSWITCH1000 7 Management Port Configuration Only
11. el B Fibridae l ER Cer f socasj O0000rx TA Sn IO c 882895 CCOO 100M LINK 234 DTESTEID NBA RESET VLAN 1 Management Management LEDs for Twist pair Port Port Ethernet Ports Twist pair Console Ports Reset General Button Switch for LEDs VLAN 2 Rear Panel e si 220VAC 48VDC PowerJack Power Jack Only available for MANAGED type Only available for UNMANAGED type kk PAGE 9 fFibridge 5 4 LEDs Function Description FBSWITCH1000 User Manual Table 1 LEDs Function Description Function gavel LED Color Se Status State Description Description ON Power Supplv Ok PWR Green Power Status OFF No Power Supplv or Power Failure Device Blink Device is running ACT Yellow Running ON Software embedded in Status OFF device is down Console Blink Console management Management port is transmitting data COM Yellow Port Data OFF No data transmission on Transmitting console management port Twist pair ON Port linked ment Port is transmitting or LINK Yellow 17702 Bink 9 port Link Act receiving data Status OFF Port not linked Twist pair ON 100Mbps 100M Green management port link OFF 10Mbps speed ON Port linked LINK Port Link Act Port is transmitting or Yellow Blink a ACT Status r
12. unction Only Available for Managed Type e Support Console WEB and SNMP management e RS 232 DB9 female management port and 10 100Mbps RJ45 Ethernet management port available e Show details of system information including device name location information IP address start up time software and hardware version e View amp configure the working status of each port including link status link speed duplex mode port shutdown status e Set transmit and receive speed bandwidth limitation from OMbps to 100Mbps with step of 32Kbps e Provide port based VLAN and 802 1Q VLAN configuration and port based priority and 802 1p priority setting e Port mirroring function available e Summarize the data flow information and show the communication state of each port e Support SNMP management Set Trap Destination Community Name and authority e A float window available for real time alarm messages And all alarm messages can pop up to get more attention e Reset the management part all 5 Ethernet ports or both via management software e Reset device to factory default with network configuration PAGE 5 fFibridge resetting or not selectable e Show the detailed information of power supply including AC DC type output power and running status e Support firmware updating with the update tool program and new version firmware file download from our website e Provide MIB file make it easy to be integrated into the third party SNMP
Download Pdf Manuals
Related Search