User Manual
Contents
1. C of the surrounding temperature When the temperature is stable the regulator sends heart beat data every 5 minutes which is signalled with the LED blinking orange on the RTH receiver e In the event of a power outage the RTH receiver will switch off When power is restored the heating device is switched on automatically and the RTH receiver awaits a signal from the paired transmitters this signal should be received within 5 minutes of restoring power After receiving the signal the RTH receiver enters the normal mode of operation e The RTH receiver cannot be placed in metal containers e g an assembly box a metal enclosure of a heater in order to not to interfere with its operation Technical specifications Working temperature range 0 45 C Temperature measurement range 7C 15 35 C Span 0 2 C Temperature levels qi Antifreeze temperature TE Working cycles 24 hours Working mode control LED Maximum load 16A 250VAC Power supply T 1 pre installed lithium battery Power supply RTH 230VAC 50Hz Radio frequency 868MHz Operation range in a typical building with standard construction of walls approx 30 min an open space up to 300 m Disposing of the devices The devices are marked with the crossed waste bin symbol According to European Directive no 2002 96 EU and the Act concerning used up electric and electronic equipment such a marking indicates that th2. always be at 22 C regardless of temperature fluctuations in the kitchen The factory setpoint 20 C if the T 2 thermometer is the only device paired with the RTH receiver it is not possible to set the temperature manually and the RTH receiver maintains the factory temperature setpoint of 20 C NOTE 1 The sequence of pairing the AURATON T 1 regulator and the T 2 thermometer is verv important If vou want to maintain the remote setpoint vou must first pair the AURATON T 1 with the RTH receiver and then the T 2 thermometer Reversing the pairing sequence will cause automatic deregistering of the previously paired T 2 thermometer and entering the mode of operation described initem A The RTH receiver can operate with one AURATON T 1 regulator and or one T 2 thermometer only Pairing a new regulator causes deregistering the previously paired regulator and the T 2 thermometer Pairing a new T 2 thermometer causes deregistering the previously paired T 2 thermometer only The 2025 RTH regulator and or the T 2 thermometer can operate with an unlimited number of receivers e g one regulator can simultaneously control two independent heating devices 13 Cooperation with the AURATON T 1 regulator and or the AURATON T 2 thermometer as well as the AURATON H 1 handles or the AURATON W 1 window position sensors Bv default the AURATON RTH receiver does not have anv AURATON H 1 handle or AURATON W 1 window position sensor
3. operation the regulator must be installed on an interior wall of a building partition wall A place should be selected that is occupied most frequently providing undisturbed circulation of air Avoid heat radiating devices television set heater refrigerator etc or places exposed to direct sunlight In order to avoid vibration do not place the regulator in close vicinity of doors Rp ese 150cm Fastening the temperature regulator to the wall NOTE Before installing the appliance to the wall it needs to be paired with a previously connected receiver A controller T 1 and a receiver purchased together do not require pairing The appliances have been already pre paired 1 Drill two 5mm holes in the wall select the span of holes with a wall mounted holder enclosed to the set with controller AURATON T 1 2 Insert the wall anchors to the holes attached to a set 3 Fixthe mounting plate to the wall 4 Press to join the regulator tightly against the mounting holder the holes ona back part of the unit should be suitable for snap on of the holder NOTE If the wall is made of wood there is no need to use the wall anchors Drill 2 7mm holes in the wall instead of 5mm and screw the screws directly inawood Pairing the AURATON T1 with the RTH receiver NOTE The AURATON T1 wireless temperature regulator sold with the AURATON RTH receiver is already paired Devices sold separately
4. 1 The process of pairing the T 1 regulator with the RTH receiver is initiated by pressing the left pairing button marked with a green triangle Y on the RTH receiver and holding it for at least require pairing o o yw LED gt e ol oll 2 seconds until the LED starts flashing green and then releasing the button The AURATON RTH receiver waits for pairing for 120 seconds After that time it automatically returns back to normal operation 2 Press the pairing button placed on the rear side of housing and hold it for about 2 seconds When LED diode 3 will starts flashing red stop pressing the button 3 A properly completed pairing process is signalled by the LED on the AURATON RTH receiver no longer flashing green and the receiver reverting back to normal operation In the event of an error during the pairing process repeat steps 1 and 2 Should more errors occur deregister all devices by executing the RESET function of the RTH receiver see RESET Deregistering all devices paired with the RTH receiver and attempt to pair the device again NOTE One receiver can have only one temperature regulator assigned Deregistering the regulator from the RTH receiver 1 Deregistering the T 1 regulator from the RTH receiver ee is initiated by pressing the right deregistering button marked with a red triangle A on the O RTH receiver and
5. KULL T 1 RTH www auraton pl WV AURATON T 1 User Manual Thank vou for purchasing this modern advanced microprocessor based temperature regulator AURATON T 1 RTH B Box c o 0 Pre installed lithium batterv Wireless temperature controller is equipped with a highest quality lithium battery produced by a Swiss Company Swatch Group Such battery provides an uninterrupted operation time of a controller AURATON T 1 up to 20 years Standard temperature controllers usually require the battery replacement Therefore the standard thermostat uses 20 40 batteries within 20 years This causes additional costs and introduces harmful substances to the environment every year Operation under the load of up to 16 A The AURATON RTH receiver is equipped with a relay capable of operating with the load of up to 16 A Its low sparking technique of switching mains voltage contributes to the low wear of relay contacts Interference free communication between devices The transmitter and the receiver from the AURATON T 1 RTH set communicate at the frequency of 868 MHz Very short encrypted data transmission packets approx 0 004 s ensure very efficient and interference free operation of the device LED LED s diode indicates the operation mode status of the controller ontent elements of the assy Actuator Wireless Mounting plate handle executive device temperature controller fixing an appliance Re
6. and an overcurrent protection 6 7 Fastening the RTH receiver to the wall To fasten the AURATON RTH receiver to the wall 1 Remove protective covers from the lower and upper part of the regulator See chapter Fastening the RTH receiver 2 Onthe wall mark the location of holes for fastening screws 3 In marked places drill holes of a diameter corresponding to the bundled wall plugs 5 mm 4 Insertwall plugs into the drilled holes 5 Screw in the RTH receiver to the wall with screws making sure thev hold the receiver securelv hole for fastening the receiver to the wall with a screw B alee EB WV AURATON RTH ging hole for fastening the receiver to the wall with a screw NOTE If the wall is wooden there is no need to use wall plugs In such a case drill two holes 2 7 mm in diameter instead of 5 mm and screw the screws directly into the wood NOTE The RTH receiver cannot be placed in metal containers e g an assembly box a metal enclosure of a heater in order to not to interfere with its operation 7 aa a Selecting the proper location for the temperature regulator Proper operation of the regulator is greatly affected by its location Installing it in a place with no air circulation or exposed to direct sunlight causes improper regulation of temperature In order to ensure proper
7. ceiver AURATON T 1 to the wall AURATON RTH NOTE The AURATON T 1 wireless temperature regulator sold with the AURATON RTH receiver is already paired Devices sold separately require pairing 3 Optional elements of the svstem AURATON H 1 Window handle sold separatelv A window handle equipped with a position sensor and a transmitter is an optional element of the svstem This wav the handle provides information about the state of the window The handle also differentiates between 4 widow positions opened closed pivoted and trickle ventilated micro ventilation The handle transmits information to the RTH receiver that controls the relav e g switching off a heater in the event of opening the window or lowering the temperature down to 3 C to conserve energy One RTH receiver operates with max 25 handles Ww AURATON T 2 l Thermometer sold separatelv Anoptional element of the svstem allowing for controlling temperature inaroomother than that with the AURATON 2025 RTH regulator o AURATON F 2 Detailed information about optional elements of the svstem are included in a section Operating rules Description of the AURATON T 1 and AURATON RTH receiver AURATON T 1 Wireless temperature controller holes for fixing diode indicating Fa SS Wan oN the wall mounting data transmission Vy AN older IM vv is diode indicating pairing temperature setpoint knob A setpoint of antifreeze
8. cuting the RESET function the RTH receiver is disconnected from power supply and then connected again the receiver will automatically enter pairing mode for 120 seconds A newly purchased RTH receiver without any factory paired devices i e not the one bundled with the regulator will behave the same way Signalling operation and reception of data packet Each radio transmission received by the AURATON RTH receiver from the paired device is signalled by a temporary change of LED colour to orange Switching on the relay is signalled by the LED lit red whereas switching it off is signalled by the LED lit green Setting the anti freezing temperature A Acontroller is equipped with antifreeze mode A This operation mode results in maintaining the room temperature amounting 7 C It is used during longer absence to prevent freezing of water in heating installation Cooperation of the RTH receiverwith a heating device Basic configuration of devices Additional svstem devices AURATON RTH AURATON T 1 Receiver connected Wireless to the heating device temperature regulator we o amaron TA AURATON T 2 AURATON H 1 Wireless thermometer Window handle sold separately sold separately AURATON W 1 Window position sensor sold separately gad KAT EA RAT moe A REG LE g heating device O O O A simplified schemat
9. drops below 7 C the relay inside the receiver is switched on regardless of the positions of windows in order to prevent the room from freezing D The signal is lost When the RTH receiver has lost the signal from the H 1 handle or the W 1 window position sensor paired 3 consecutive transmissions are lost it changes the status if this window to closed When the transmission is restored the H 1 handle or the W 1 window position sensor is again properly read off by the RTH receiver 14 RIH cooperation with the air conditioner Max 16A air conditioner OJOjO NOCOMNC L Simplified wiring diagram of the air conditioning appliances Cooperation AURATON RTH receiver with thr AURATON H 1 handles and or the AURATON W 1 window position sensors without T 1 and T 2 In order for the RTH receiver to be able to control the air conditioning it cannot be associated with any T 1 controller or T 2 thermometer and must be associated with at least one H 1 handle Upon fulfillment of the above requirements the RTH receiver automatically goes into the air conditioning control mode Window open or ajar If we connect the power supply circuit of the air conditioning device through the transmitter and open or leave ajar any window with the associated H 1 handle for longer than 30 sec the transmitter in the RTH receiver will turn off the air cond
10. g the regulator from the RTH receiver ARM TheLED flashes alternating red and green SET ALARM the RTH receiver has lost connection with one of the paired devices chapter Special situations RESET receiver deregisters all previously paired devices chapter Deregistering all devices paired with the RTH receiver Fastening the RTH receiver NOTE When installing the AURATON RTH i receiver its power supplv must be disconnected It is recommended that the f installation is performed by a qualified specialist 1 Take off protective covers from the lower and upper part of the AURATON RTH receiver protective cover and upper part of the AURATON RTH 2 Take off cable tie clamps from the lower 1 receiver cable tie clamp o_o 3 Connect the heating device to the control connection terminals of the eeelo AURATON RTH receiver WV Proceed in accordance with the service manual of the heating device Most commonly the COM common and NO normally open terminals 4 Connect power supply conductors to the power supply terminals of the AURATON AURATON RTS ae RTH receiver observing safety rules 5 After connecting the conductors they must be secured with the cable tie clamps and reinstall protective covers of the AURATON RTH receiver NOTE The permanent electrical system of a building must include a breaker
11. he 230 V mains voltage in order to ensure that closing and opening contacts of the relay occurs around the zero crossing point This prevents the occurrence of an electricarc significantly extending the relay service time e The AURATON RTH receiver is equipped with a unique algorithm for analysing the ON OFF cycles The entire heating cycle from the last 24 hours is recorded in the memory of the RTH receiver In the event of losing communication with the AURATON T 1 RTH regulator and or the T 2 thermometer the RTH receiver automatically executes the ON OFF cycle memorised during the last 24 hours This provides time for restoring transmission removing interferences or fixing the T 1 regulator and or the T 2 thermometer without a significant deterioration of thermal comfort conditions in the controlled spaces e The AURATON T 1 regulator and the RTH receiver are ready for remote control performance A USB remote control module sold separately accompanied by the appropriate software will be available in 2012 More details are available at WWW AURATON PL Additional information and notes e The AURATON T 1 regulator and or the T 2 thermometer must be installed at least 1 metre from the RTH receiver too strong a signal from the transmitters can cause interference At least 30 seconds must elapse between switching the relay off and on e Data transmission from the AURATON T 1 regulator to the receiver occurs upon each change of 0 2
12. holding it for at least 2 seconds until the LED starts flashing red and then releasing WV ien thebutton The AURATON RTH receiver waits for deregistering for 120 seconds After that time it automaticallv returns back to normal operation fe 6 2 Press the pairing button placed on the rear side of housing and hold it for about 2 seconds When LED diode will starts flashing red stop pressing the button ES 3 A properly completed deregis tering process is signalled by the LED on the AURATON RTH receiver no longer flashing red and the receiver reverting back to normal operation In the event of an error during the deregistering process repeat steps 1 and 2 Should more errors occur deregister all paired devices see RESET Deregistering all devices paired with the RTH receiver and attempt to pair the device again 10 RESET Deregistering all devices paired with the RTH receiver i eo T 8 In order to deregister all devices paired with O O the RTH receiver simultaneously press both the pairing and the deregistering button l l Vand 4 and hold them for at least V V 5 seconds until the LED flashes alternating red and green Then release both buttons A properlv completed process of deregistering all devices is signalled after approx 2 seconds bv the LED colour changing to green and then switching it off for a short period of time NOTE If after exe
13. ic NO COM NC AURATON RTH oool of connecting the AURATON RTH receiver with the heating device Cooperation of the AURATON RIH receiver with the AURATON T 1 regulator and or the AURATON T 2 thermometer The operation of temperature regulation in the receiver is based on the binarv algorithm on off using one or two sensor elements The AURATON T 1 regulator allows for setting and or monitoring the temperature e The AURATON T 2 thermometer provides information about the current temperature only without the capability of changing it manually A The manual setpoint pairing the AURATON T 1 regulator with the RTH receiver allows for setting the temperature manually and controlling it in the location of the fastening of the T 1 regulator B c The remote setpoint if the T 2 thermometer is additionally paired with the RTH receiver the AURATON T 1 regulator retains the capability of temperature setting however its control is performed with the paired T 2 thermometer only This feature allows for regulating the temperature in aroom other than the one where the AURATON T 1 regulator is placed An example you want the temperature in the children s room to be always at 22 C however you do not want children to be able to change it in that room you install the T 2 thermometer and the AURATON T 1 regulator in e g the kitchen This way the temperature in the children s room will
14. is equipment may not be placed with other household generated waste The user is responsible for delivering the devices to a reception point for used up electric and electronic equipment 18 A template for drilling holes for fastening the AURATON RTH receiver 1 1 scale CE www duraton pl
15. itioning device Window closed or unsealed If all windows with the associated H 1 handle will again be in the position other than open or ajar the RTH receiver after time not shorter than 90 sec from turning off the transmitter shall again activate the transmitter and the air conditioning device This is an intentional delay to prevent too rapid changes of air conditioning devices between the ON OFF position which can lead to compressor damage Loss of signal When the RTH receiver loses signal from the associated H 1 handle 3 subsequent transmission losses it changes this window s status to closed After restoring the transmission the sensor is again correctly read by the receiver NOTE the association of the RTH receiver with the T 1 controller or T 2 thermometer automatically changes the way the receiver works to controlling the heating device Note One AURATON RTH receiver can operate max 25 handles Special situations e When 3 consecutive transmissions after 15 minutes from the AURATON T 1 regulator and or the T 2 thermometer are lost an error is signalled on the RTH receiver LED flashing continuously red and green The RTH receiver starts executing the ON OFF cycle memorised during the last 24 hours of operation until the problem is removed e When both signals return from the AURATON T 1 regulator and the T 2 thermometer the error is cancelled and the receiver enters its normal mode of operation e When on
16. ly the T 2 thermometer signal returns the receiver uses the last memorised setpoint value and maintains it while signalling the error e When the H 1 handles or the W 1 window position sensors the T 2 thermometer and the AURATON T 1 regulator the temperature is measured with the T 2 thermometer are paired with the receiver then maintaining the work cycle from the last 24 hours occurs only after losing the signal from the T 2 thermometer When only the signal from the AURATON T 1 is missing the RTH receiver automatically maintains the last memorised setpoint from the AURATON T 1 regulator and also signals an error e When you have only the H 1 handles or the W 1 window position sensors and the 7 2 thermometer paired with the RTH receiver without the AURATON T 1 regulator the RTH receiver maintains a constant factory defined temperature of 20 C If you pivot any window equipped with the H 1 handle or the W 1 window position sensor paired with the receiver a temperature of 17 C is maintained If you open any window equipped with the H 1 handle or the W 1 widow position sensor paired with the RTH receiver the receiver switches off the heating device but will switch it back on when the temperature falls below 7 C 16 zz Unique features of AURATON T 1 e A pre installed lithium battery produced by Swiss Company Swatch Group provides an interrupted operation up to 20 years Switching the relay is synchronised with the wave of t
17. paired therefore the relay is controlled by the paired AURATON T 1 regulator and or the AURATON T 2 thermometer When at least one H 1 handle or one W 1 window position sensor is paired with the RTH receiver the relay is controlled in the following manner A The window is closed or trickle ventilated micro ventilation When the H 1 window handles or the W 1 are paired with the receiver and all windows are closed or trickle ventilated the relay still maintains the setpoint from the paired AURATON T 1 regulator and or the T 2 thermometer B The window is pivoted If at least one window is pivoted the temperature set in the AURATON T 1 regulator is lowered in AURATON RTH receiver down to 3 C This state will be maintained until closing This state will last until all windows are closed or trickle ventilated C The window is opened When you open a window equipped with the H 1 handle or the W 1 window position sensor paired for longer than 30 seconds the relay in the AURATON RTH receiver is switched off as is the connected heating device If all the assigned windows are again in a state other than opened the RTH receiver returns to normal cooperation with the AURATON T 1 regulator and or the T 2 thermometer no earlier than 90 seconds after switching off the relay The purpose of this delay is to prevent too rapid transitions of the connected heating devices between the ON and OFF states However if the temperature in the room
18. temperature 7 C bottom indicating pairing with a receiver OJI mQ temperature sensor AURATON T I FRONT BACK AURATON T 1 is equipped with pre installed lithium battery Life span of the battery is up to 20 years AURATON RTH The receiver is installed on the heating or air conditioning device and can operate under the load of 16A button for pairing devices with the RTH receiver cable tie clamp power supply terminal 230 VAC hole for fastening the receiver to the wall with a screw NO COM 230 VAC NC hole for fastening the receiver to the wall with a screw cable tie clamp control connection terminal a terminal for fastening a two core cable of the heating or air conditioning device to be controlled button for deregistering already paired devices LED indicating operation of the device legend Legend description of LED signalling OFF The LED light s green the output device is off the contacts COM and NCare closed e oN The LED light s red the output device is on the contacts COM and NO are closed regulator and the RTH receiver The LED flashes green the RTH receiver awaits the device to be paired chapter Pairing the AURATON 2025 RTH wireless 7 ouT The LED flashes red the RTH receiver awaits the device to be deregistered chapter Deregisterin
Download Pdf Manuals
Related Search