SCS317_User Instructions - Z
Contents
1. In the unlikely event of a fault developing please refer to the RESETTING THE SCS317 THERMOSTAT on page 21 If this fails to resolve the problem please contact a local heating engineer or a qualified electrician SECURE Cewe Instrument AB Box 1006 611 29 Nykoping Tel 46 8 600 80 60 Email info securetogether eu C Web Site www securetogether eu Neba busied eesi 222. and Year HOLIDAY programme is now set 10 If the holiday period START date matches today s date the STANDBY temperature will be shown on the display together with the suitcase icon If the holiday period START date does not match today s date the display will remain in normal operating mode but with the suitcase icon appearing on the right of the display Indicating a holiday period is pending _ wo omm AM or gog THEN m 20 a To cancel a set holiday programme in ADVANCE of its activation re programme using the above procedure and set the START date and BACK date to today s date To cancel a set holiday programme during activation press ENTER button twice the unit will return to normal operating mode and the suitcase icon will disappear THE DATES SPECIFIED BECOME EFFECTIVE FROM MIDNIGHT OF THE DAY ENTERED Setting the TIME and DATE Pressing BACK at any time in this process will return you to normal operating mode Press ENTER twice The minutes for the time of day will flash 4 Press or to lt Press or until Time Date appears on the display Press ENTER Press or to adjust hours then press ENTER adjust minutes then press ENTER The day of the date will now flash The hours for the time of day will flash Press or to adjust the day to match today s d
3. ENU OPTIONS Programme This allows the user to adjust the different time and temperature settings from the factory default settings shown in the table on page 6 Up to six different temperature levels can be set in any 24 hour period Standby This puts the SCS317 into Frost protection or Standby condition and allows the heating to be permanently switched off but will activate and switch the heating on if the temperature in the house falls below the standby temperature set All programme settings are overridden and the unit will not return to normal operation until the standby period has ended by pressing the ENTER button Holiday This puts the SCS317 into a temporary standby mode with a start and end date which can be set to coincide with a holiday period At the end of the set period the SCS317 will resume normal operation Time Date The SCS317 has a built in clock and calendar This will require setting on initial installation If this has not been set on installation please go to Setting the TIME and DATE section on page 12 before continuing Set Up Enables the programming of various options outlined in the SET UP MENU on page 13 of these instructions These should be set on installation Setting the PROGRAMME Six time and temperature settings are available in each 24 hour period Pressing BACK at any time in this process will return you to normal operating mode Press ENTER three The day of the week Eed
4. NTER appears on the gt PENT mp Press ENTER Press or until gt display The unit will now return to the Set Up position simply press BACK to return to normal operating table below mode Oil Boilers 3 cycles per hour Gas Boilers 6 cycles per hour Not used 9 cycles per hour Electric Heating 12 cycles per hour This feature would normally be set by your installer 17 Setting the OPTIMUM START This setting will allow the SCS317 to anticipate the next set temperature and switch on up to two hours in advance to ensure room temperature has been reached by the time the new set temperature applies As aconsequence the switch on time could take place anywhere between 2 hours and zero before the set time and temperature With the optimum start set to OFF the user will need to anticipate the warm up time needed in the programme settings Typically the set temperature will be set approx 1 hour in advance of when itis required Pressing BACK at any time in this process will return you to normal operating mode Press or until Press ENTER twice Set Up appears on gt Press ENTER the display Press or until Optimum Start appears on the display Select YES or NO and press ENTER to confirm This feature would normally be set by your installer 18 Setting the TAMPER SETTING This set
5. SECURE SCS317 User Instructions SCS317 7 Day Wireless Programmable Room Thermostat Programmable room thermostats are widely recognised as one of the best ways in which to control central heating The SCS317 programmable room thermostat has a large display and intuitive user interface making it easy to set up and use SCS317 uses a sophisticated time proportional integral TPI algorithm for accurate temperature control and energy efficiency CS317 DISPLAY Actual Room Day of Time of Temperature Week Day Until Time Set Temperature Then Temp Back Button Button Enter Button Button DISPLAY Actual Room Temperature This is the actual room temperature measured by the SCS317 Set Temperature Until time This is the temperature that the SCS317 will allow the room to reach The temperature range can be set between 5 C and 30 C When the temperature shown in the display is achieved the SCS317 will switch the heating OFF If the temperature in the room falls below the setting the SCS317 will switch the heating ON This is the time that the next temperature setting is due to operate Then temp This is the temperature setting that is due to operate next Day of the week It is important that the correct day of the week shows in the display Time of day This is the current time of day Setting Buttons Press any button to illuminate the display The message To
6. ate Pressing ENTER to change between Day Month and Year Time and Date are both set and the unit will return to normal operating mode If an incorrect date is entered the wrong day will appear in the normal operating scree n 12 SETUP MENU To access the SET UP MENU take the following steps Press ENTER twice MENU OPTIONS Press or until Set Up appears on the display E gt Press ENTER Press or to toggle between the menu options detailed below Select clock format This allows the display to show the time in 24 hour or AM PM format Daylight saving This is the adjustment made in the UK when the clocks go back or forward in the Autumn and Spring Default setting ON Standby temperature This is the temperature setting used when in Standby or Holiday mode Min 5 C Max 30 C In cold weather the heating will activate if the temperature being measured falls below this temperature setting Lower temperature limit Upper temperature limit This sets the lowest temperature setting the SCS317 will allow to be programmed The default setting is 5 C This sets the highest temperature setting the SCS317 will allow to be programmed The default setting is 30 C 13 MENU OPTIONS Contd TPI cycles per hour This setting helps the TPI energy saving software to operate correctly dependin
7. g on the type of heating system you have Optimum start This calculates the amount of time the SCS317 may need to switch on in advance of the next target temperature setting in order to meet the requirement Tamper setting This setting allows a 4 digit release code to be set up to stop unauthorised adjustments being made in multi occupancy buildings Set up Z Wave Wireless connection to receiver Setting the SELECT CLOCK FORMAT Pressing BACK a any time in the process will return you to normal operating mode Press ENTER twice Either Select clock 24 hr or Select clock AM PM will appear Press or until Set Up appears on gt Press ENTER the display Press or until Select clock format E Press ENTER K appears on the display Press or to the two options toggle between by pressing ENTER return to the Set up Select your choice The unit will now position simply press BACK to return to normal operating mode 14 Setting the DAYLIGHT SAVING Pressing BACK at any time in this process will return you to normal operating mode The default factory setting is for the Daylight saving to be ON Press ENTER twice Either Daylight Saving Off or Daylight Saving On will appear on the display 4 Press or to toggle between the two opt
8. ions gt Press or until the display Set Up appears on Press ENTER Select your choice by pressing ENTER gt Press ENTER Press or until Daylight saving appears on the display The unit will now return to the Set up position simply press BACK to return to normal operating mode 15 Setting the STANDBY TEMPERATURE LOWER TEMPERATURE LIMIT or UPPER TEMPERATURE LIMIT Pressing BACK at any time in this process will return you to normal operating mode Press ENTER twice The temperature setting will now flash gt Press or until Set Up appears on the display Press ENTER Press ENTER Press or until the required option appears on the display gt Press or to adjust temperature then press ENTER operating mode The unit will now return to the Set Up position simply press BACK to return to normal 16 Setting the TPI cycles Pressing BACK at any time in this process will return you to normal operating mode Press ENTER twice The current setting will now flash 4 Press or to adjust to the correct setting for your heating system Please refer to Press or until Set Up appears on the display TPI Cycles per hour 4a Press E
9. lowing message will appear Tamper Code Cleared The following message will appear Enter first digit 20 RESETTING THE SCS317 THERMOSTAT Electronic equipment can in some circumstances be affected by electrical interference If the display becomes frozen or scrambled simply press both the BACK and ENTER button simultaneously Using this procedure will restore the SCS317 to the original factory settings the Time and Date will remain correct Pirie t t BATTERY The SCS317 thermostat runs on 2 standard AA Alkaline non rechargeable batteries and is designed to give a battery life of approximately two years There are three stages of warning as the batteries become low in power Stage 1 The battery low symbol will appear in the display Stage 2 The words Low Battery will appear in the display for 1 second each time a button is operated Stage 3 The unit will switch itself OFF and the message Replace Batteries will appear permanently in the display The batteries should be changed at Stage 2 at the latest 21 To replace the batteries of the SCS317 please carefully pull down the hinged battery cover on the front of the unit Ensure they are fitted correctly as indicated by the terminal markings in the battery compartment Please dispose the old batteries responsibly x SERVICE AND REPAIR This programmer is NOT user serviceable Please do not dismantle the unit
10. override press To see menu press ENTER will appear 1 No Radio waves Wireless connection not set up Solid Radio Antenna Z Wave communication present Flashing Radio Antenna Temporary loss of Z Wave communication ACTIVATING THE BACK LIT DISPLAY Press any button to illuminate the display This will remain illuminated for 10 seconds GENERAL INFORMATION During programming please note that the display will return to its normal operating screen if the last button press exceeds 10 seconds TEMPORARY OVERRIDE A temporary temperature change can be made at any time It is also possible to extend how long this temperature override is in operation Press or to adjust temperature gt New temperature setting will be shown on the display The temperature will revert to its normal programmed setting at the next timed temperature change TEMPORARY OVERRIDE WITH TIME EXTENSION Maximum of 4 hours Press or to adjust temperature gt New temperature setting will be shown on the display Press ENTER 4 Press ENTER 4 Press to adjust the time The hours of the UNTIL time will flash The temperature will revert to its normal programmed setting at the next timed temperature change PERMANENT OVERRIDE Press or to ladjust tem
11. perature gt Press ENTER 4 4 Message will appear briefly confirming Temperature set until manual release New temperature setting will be shown on the display gt Press the repeatedly until HOLD appears in the display Press ENTER 4 The hours of he UNTIL time will flash In the HOLD position the temperature can be overridden by pressing either the or buttons This will then become the new HOLD temperature PERMANENT OVERRIDE CANCELLATION Press BACK gt Press ENTER SETTING UP THE SCS317 Upon initial installation the SCS317 has the following factory default settings Settings Monday to Friday Time Target Temperature Period 1 06 00 am 20 C Period 2 08 30 am 18 C Period 3 11 30 am 20 C Period 4 01 30 pm 18 C Period 5 05 00 pm 21 C Period 6 10 00 pm 15 C Settings Saturday and Sunday Time Target Temperature Period 1 07 00am 20 C Period 2 10 00 am 19 C Period 3 11 30 am 21 C Period 4 01 30 pm 18 C Period 5 05 00 pm 21 C Period 6 11 00 pm 15 C These can be changed by the installer or the end user at any time by accessing the MAIN MENU MAIN MENU To access the MAIN MENU take the following steps Press or to toggle between the menu options Press ENTER twice gt M
12. ss below When you have set The next P6 the message To gt Press ENTER gt sequential day Copy press ENTER will now flash will appear When complete press BACK Press or to select the to return to normal operating days you wish to copy the mode lt a set programmes Pressing ENTER after each day to confirm 4 To programme remaining days please go to the start of the process Setting the PROGRAMME Setting the STANDBY Press or until Press ENTER Twice STANDBY Press ENTER p appears on the m display After a short period Standby The words STANDBY and Enabled will disappear from Standby Enabled will appear the display lt a on the display To exit STANDBY mode press ENTER TWICE Setting the HOLIDAY programme Pressing BACK at any time in this process will return you to normal operating mode Press or until Press ENTER twice p HOLIDAY appears on the display The BACK date will now flash Press the or to adjust to the date you wish the holiday programme to start Pressing ENTER to change between Day Press ENTER The START date will now flash 4 Month and Year Again Press the or to adjust to the date you wish the holiday programme to end Pressing ENTER to change between Day Month
13. times m wil flash gt programme Press or to 4 lect time teniperatine period 4 Time Temperature Press ENTER you wish to set P1 setting P1 will flash lt a to P6 Temperature will flash use the or Press ENTER p to select the gt Press ENTER required temperature J Press or to Press or to adjust the minutes adjust the hours The hours START then press ENTER K ba erectile time will flash 4 then flash If you require to set further periods for On completion of period 6 the same day the next period will now P6 go to the copy automatically flash Follow this process process on Page 9 of this again to programme as required booklet If only two different temperature settings are required in 24 hours then set the first time and temperature using programme one P1 and the second time and temperature setting using programme setting two P2 The remaining programmes P3 to P6 should all be set to the same time and temperature as P2 This same method can be used if three four or five temperature levels are required always using the first settings to provide the temperature change commands with the remaining settings that are not required set to the same time and temperature as the last required setting 8 To copy the same programmes to other days of the week please follow the proce
14. ting allows the unit to be locked to the programmes set and can only be reactivated by entering the pin code None of the buttons will operate until the security code is entered Pressing BACK at any time in this process will return you to normal operating m Press ENTER twice The first digit of FOUR will now flash 4 Press or to adjust to a number of your choice 0 9 then press ENTER gt ode Press or until Set Up appears on the display Press ENTER Press ENTER Press or until Tamper Setting appears on the display gt Repeat the previous step for the second third and fourth digits PLEASE MAKE A NOTE OF THIS CODE AND KEEP IN A SAFE PLACE THIS WILL BE REQUIRED TO MAKE ANY CHANGES IN THE FUTURE A message will appear briefly confirming Tamper code set when this message clears 19 Cancelling the TAMPER SETTING Pressing BACK at any time in this process will return you to normal operating mode Press ENTER twice gt The following message will appear To enter release code press ENTER gt Press ENTER Repeat the previous step for the second third and fourth digits digi Press or to confirm the first code then press ENTER of the release The fol
Download Pdf Manuals
Related Search