Home

N150 Wireless ADSL2+ Modem Router DGN1000 User Manual

1. Inbound Services Enable Service Name Action LAN Server IP address WAN Users Log Default Yes Any BLOCK Always Any Any Never WAN Users Add Edit Move Delete Instant Messaging IM Ports O Close IM Ports 9 Open IM Ports IM ports are open by default Apply Cancel Figure 28 Block computers in your network from using certain Internet services Under Outbound Services click Add Fill in the settings as follows and click Apply to save your settings Service From this list select the application or service to be allowed or blocked The list already displays many common services but you are not limited to these choices Use the Add Custom Service button in the Services screen described in Configure Services on page 52 to add any additional services or applications that do not already appear Action Choose how to handle this type of traffic You can block or allow always or you can block or allow according to the schedule you defined as described in Schedule Firewall Services on page 55 LAN Users These settings determine which packets are covered by the rule based on their source LAN IP address Select the option that you want Any All IP addresses are covered by this rule Address range If this option is selected fill in the Start and Finish fields Single address Enter the required address in the Start field WAN Users These settings determine which packets are covered by the rule based on the
2. Remote Management e Static Routes Universal Plug and Play Chapter 6 Advanced Settings 70 N150 Wireless ADSL2 Modem Router DGN1000 User Manual WAN Setup The WAN Setup screen lets you configure a DMZ demilitarized zone server change the Maximum Transmit Unit MTU size and enable the wireless router to respond to a ping on the WAN Internet port Select Select Advanced gt WAN Setup to display the following screen WAN Setup Connect Automatically as Required C Enable PPPoE Relay C Disable Port Scan and DOS Protection C Default DMZ Server Respond to Ping on Internet WAN Port MTU Size in bytes C Disable SIP ALG Cancel Figure 44 Enable or disable WAN settings Fill in the fields as follows Connect Automatically as Required This option is enabled by default so that Internet connections are made automatically whenever Internet bound traffic is detected If this causes high connection costs you can disable this setting and connect manually from the Router Status screen See Connection Status Button In the Router Status screen click the Connection Status button to display a screen similar to this on page 67 Enable PPPoE Relay When enabled this feature allows a PPPoE client on a local PC to connect to a remote PPPoE server with the gateway acting as a relay agent Disable Port Scan and DOS Protection The firewall protects your LAN against port scans and denial of service DOS attack
3. Remote Management Cl Turn Remote Management On Remote Management Address Allow Remote Access By Only This Computer IP Address List 9 Everyone Port Number Cancel Figure 49 Upgrade or check your router over the Internet 2 Select the Turn Remote Management On check box 3 Specify the external addresses of wireless modem routers than can access remote management For security restrict access to as few external IP addresses as practical To allow access from a single IP address on the Internet select Only This Computer and enter the IP address that is allowed access To allow access from a range of IP addresses on the Internet select IP Address and enter a beginning and ending IP address to define the allowed range To allow access from any IP address on the Internet select Everyone 4 Specify the port number to be used for accessing the router interface Web browser access usually uses the standard HTTP service port 80 For greater security you can change it so the remote router interface uses a custom port by entering Chapter 6 Advanced Settings 79 N150 Wireless ADSL2 Modem Router DGN1000 User Manual that number in the field provided Choose a number between 1024 and 65535 but do not use the number of any common service port The default is 8080 which is a common alternate for HTTP 5 Click Apply to save your changes To access your wireless modem router from the Internet
4. Schedule Firewall Services If you enabled services blocking in the Block Services screen or port forwarding in the Ports screen you can set up a schedule for when blocking occurs or when access is not restricted 1 Select Security gt Schedule to display the following screen Schedule Every Day Sunday Monday Tuesday Wednesday Thursday Friday Saturday Time of day use 24 hour clock 7 All Day Start Time Hour Minute End Time Hour Minute Time Zone GMT Greenwich Mean Time Edinburgh London L I Adjust for Daylight Savings Time T Use this NTP Server Current Time 2000 01 01 00 25 26 Cancel Figure 32 Block Internet services based on a schedule 2 To block Internet services based on a schedule select Every Day or select one or more days If you want to limit access completely for the selected days select All Day Otherwise to limit access during certain times for the selected days enter times in the Start Time and End Time fields Note Enter the values in 24 hour time format For example 10 30 a m would be 10 hours and 30 minutes and 10 30 p m would be 22 hours and 30 minutes If you set the start time after the end time the schedule is effective through midnight the next day 3 Click Apply to save your settings Chapter 4 Security Settings 55 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Enable Security Event Email Notification To receive logs and alerts b
5. those devices assume the security settings of the router 18 Chapter 2 Router Internet Setup N150 Wireless ADSL2 Modem Router DGN1000 User Manual Gather ISP Information You need the following information to set up your wireless modem router and to check that your Internet configuration is correct Your Internet Service Provider ISP should have provided you with all of the information needed to connect to the Internet If you cannot locate this information ask your ISP to provide it When your Internet connection is working you no longer need to launch the ISP s login program on your computer to access the Internet When you start an Internet application your wireless modem router automatically logs you in e Active Internet service provided by a DSL account The ISP configuration information for your DSL account ISP login name and password ISP Domain Name Server DNS addresses Fixed or static IP address Host and domain names Depending on how your ISP set up your Internet account you could need to know one or more of these settings for a manual setup Virtual path identifier VPI and virtual channel identifier VCI parameters Multiplexing method Host and domain names NETGEAR Genie Setup NETGEAR Genie is on the Resource CD and runs on a PC with Microsoft Windows 7 Windows Vista Windows XP or Windows 2000 with Service Pack 2 or later It is the easiest way to set up the router because it automates many
6. 1 Select Advanced gt UPnP to display the following screen Iv Turn UPnP On Advertisement Period in minutes s a fa Advertisement Time To Live in hops UPnP Portmap Table Active Protocol Int Port Ext Port IP Address Apply Cancel Refresh Figure 53 Turn on UPnP 2 Fill in the settings as follows Turn UPnP On UPnP can be enabled or disabled for automatic device configuration The default setting for UPnP is enabled If UPnP is disabled the wireless modem router does not allow any device to automatically control the resources such as port forwarding mapping of the wireless modem router Advertisement Period The advertisement period is how often the wireless modem router advertises broadcasts its UPnP information This value can range from 1 to 1440 minutes The default period is 30 minutes Shorter durations ensure that control points have current device status at the expense of additional network traffic Longer durations might compromise the freshness of the device status but can significantly reduce network traffic Advertisement Time To Live This is measured in hops steps for each UPnP packet sent A hop is the number of steps allowed to propagate for each UPnP advertisement before it disappears The number of hops can range from 1 to 255 The default value is 4 hops which works for most home networks If you notice that some devices are not being updated or reached correctly you might ne
7. periodically When set to Both or In Only the wireless modem router incorporates the RIP information that it receives e When set to None the wireless modem router does not send any RIP packets and ignores any RIP packets received RIP Version This controls the format and the broadcasting method of the RIP packets that the wireless modem router sends It recognizes both formats when receiving By default this is set for RIP 1 e RIP 1 This version is universally supported It is probably adequate for most networks unless you have an unusual network setup Chapter 6 Advanced Settings 75 N150 Wireless ADSL2 Modem Router DGN1000 User Manual e RIP 2 This version carries more information Both RIP 2B and RIP 2M send the routing data in RIP 2 format e RIP 2B This version uses subnet broadcasting RIP 2M This version uses multicasting Access Router Interface on Additional Port When NAT is disabled the wireless modem router s management interface may be accessed at the wireless modem router s LAN address using the port number you enter This feature is not available when NAT is enabled Use Router as DHCP Server By default the wireless modem router functions as a Dynamic Host Configuration Protocol DHCP server allowing it to assign IP DNS server and default gateway addresses to all computers connected to the wireless modem router s LAN The assigned default gateway address is the LAN address of the rout
8. Automatic Other choices are Open System any client can authenticate itself to the network and Shared Key a passphrase and a four way challenge is needed for authentication 3 Select the encryption strength setting either 64 bit or 128 bit 4 Enter the four data encryption keys either manually or automatically These values are required to be identical on all computers and access points in your network e Automatic Enter a word or group of printable characters in the Passphrase field and click Generate The four key fields are automatically populated with key values e Manual The number of hexadecimal digits that you enter depends on the encryption strength setting For 64 bit WEP enter 10 hexadecimal digits any combination of 0 9 a f or A F For 128 bit WEP enter 26 hexadecimal digits any combination of 0 9 a f or A F 5 Select the radio button for the key you want to make active Make sure you understand how the WEP key settings are configured in your wireless adapter Wireless adapter configuration utilities such as the one in Windows XP allow one key entry which has to match the default key you set in the wireless modem router 6 Click Save to save your settings or click Apply so your changes to take effect immediately Chapter 3 Wireless Settings 43 Security Settings Keeping unwanted content out of your network This chapter explains how to use the basic firewall features of the wireless
9. If your router cannot obtain an IP address from the ISP the problem might be one of the following e If you have selected a login program the service name user name or password might be incorrect See Debug PPPoE or PPPoA on page 89 e Your ISP might check for your computer s host name Assign the computer host name of your ISP account to the wireless modem router in the browser based Setup Wizard See Setup Wizard on page 24 for more information e Your ISP allows only one Ethernet MAC address to connect to the Internet and might check for your computer s MAC address In this case do one of the following Inform your ISP that you have bought a new network device and ask them to use the routers MAC address Configure your router to spoof your computer s MAC address through the Basic Settings screen See Manual Setup Basic Settings on page 25 88 Chapter 7 Troubleshooting N150 Wireless ADSL2 Modem Router DGN1000 User Manual Debug PPPoE or PPPoA Debug the PPPoE or PPPoA connection as follows 1 g Pe h Access the router menus at http 192 168 0 1 and log in Under Maintenance select Router Status Click the Connection Status button If all of the steps indicate OK your PPPoE or PPPoA connection is working If any of the steps indicate Failed you can attempt to reconnect by clicking Connect The wireless modem router continues to attempt to connect indefinitely If you do not connect after several min
10. In the Route Name field enter a route name for this static route This name is for identification purpose only c Select Private if you want to limit access to the LAN only The static route will not be reported in RIP d Select Active to make this route effective Chapter 6 Advanced Settings 81 N150 Wireless ADSL2 Modem Router DGN1000 User Manual e Enter the destination IP address of the final destination f Enter the IP subnet mask for this destination If the destination is a single host type 255 255 255 255 g Enter the gateway IP address which has to be a router on the same LAN segment as the router h In the Metric field enter a number between 2 and 15 as the metric value This represents the number of routers between your network and the destination Usually a setting of 2 or 3 works 3 Click Apply to save your changes The Static Routes table is updated to show the new entry Static Routes Active Name Destination Gateway 1 Yes ex_it 134 177 0 0 192 168 0 100 Add Edit Delete Figure 52 Updated static routes Universal Plug and Play Universal Plug and Play UPnP helps devices such as Internet appliances and computers access the network and connect to other devices as needed UPnP devices can automatically discover the services from other registered UPnP devices on the network 82 Chapter 6 Advanced Settings N150 Wireless ADSL2 Modem Router DGN1000 User Manual
11. Key 8 63 characters mypassphrase Figure 21 Type in the new network key Set WPA 802 1x Server and Passphrase 1 In the Security Options section select WPA 802 1x to display the following fields WPA 802 1x Radius Server Name IP Address Figure 22 Radius server port and shared key settings 2 Inthe Radius Server Name IP Address field enter the name or IP address of the RADIUS server on your LAN This is a required field 3 In the Radius Port field enter the port number used for connections to the RADIUS server The default port is 1812 4 Inthe Shared Key field enter the RADIUS server passphrase for client logins The router has to have this passphrase to log into the RADIUS server as a client 42 Chapter 3 Wireless Settings N150 Wireless ADSL2 Modem Router DGN1000 User Manual Set WEP Encryption and Passphrase When configuring WEP from a wireless computer you lose your wireless connection when you click Apply You have to either configure your wireless adapter to match the wireless modem router WEP settings or access the wireless modem router from a wired computer 1 In the Security Options section select WEP to display the following screen WEP Security Encryption Authentication Type Automatic Encryption Strength 64bit v WEP Key assphrase Key 1 Key 2 O Key 3 O Key 4 O App Figure 23 WEP Security Encryption section 2 Select the authentication type The default is
12. Require a Login Answer either yes or no e When no login is required these fields display Account Name If required Enter the account name provided by your ISP This might also be called the host name Domain Name If required Enter the domain name provided by your ISP Chapter2 Router Internet Setup N150 Wireless ADSL2 Modem Router DGN1000 User Manual e When your ISP requires a login these fields display Encapsulation Encapsulation is a method for enclosing multiple protocols PPP stands for Point to Point Protocol The choices are PPPoE PPP over Ethernet or PPPoA PPP over ATM Login The login name provided by your ISP This is often an email address Password The password that you use to log in to your ISP Idle Timeout In minutes If you want to change the login timeout enter a new value in minutes This determines how long the wireless modem router keeps the Internet connection active after there is no Internet activity from the LAN Entering a value of 0 zero means never log out Internet IP Address e When a login is required these fields display Get Dynamically from ISP Your ISP uses DHCP to assign your IP address Your ISP automatically assigns these addresses Use Static IP Address Enter the IP address IP subnet mask and the gateway IP address that your ISP assigned The gateway is the ISP s wireless modem router to which your wireless modem router will connect e When a login is n
13. Siuo NETGEAR Inc deklaruoja kad Sis Radiolan atitinka esminius reikalavimus ir kitas 1999 5 EB Direktyvos nuostatas Nederlands Dutch Hierbij verklaart NETGEAR Inc dat het toestel Radiolan in overeenstemming is met de essenti le eisen en de andere relevante bepalingen van richtlijn 1999 5 EG Malti Maltese Hawnhekk NETGEAR Inc jiddikjara li dan Radiolan jikkonforma mal htigijiet essenzjali u ma provvedimenti ohrajn relevanti li hemm fid Dirrettiva 1999 5 EC Magyar Hungarian Alulirott NETGEAR Inc nyilatkozom hogy a Radiolan megfelel a vonatkoz alapvet k vetelm nyeknek s az 1999 5 EC ir nyelv egy b el r sainak Polski Polish Niniejszym NETGEAR Inc o wiadcza ze Radiolan jest zgodny z zasadniczymi wymogami oraz pozostalymi stosownymi postanowieniami Dyrektywy 1999 5 EC Appendix B Notification of Compliance 103 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Table 10 EDOC in Languages of the European Community Language Statement Portugu s Portuguese NETGEAR Inc declara que este Radiolan esta conforme com os requisitos essenciais e outras disposi es da Directiva 1999 5 CE Slovensko Slovenian NETGEAR Inc izjavlja da je ta Radiolan v skladu z bistvenimi zahtevami in ostalimi relevantnimi dolo ili direktive 1999 5 ES Slovensky Slovak NETGEAR Inc t mto vyhlasuje Ze Radiolan spliia z kladn po iadavky a v etky pr s
14. Your Router Your router s location can affect wireless connections For example the thickness and number of walls the wireless signal passes through can limit its range For best results place your router e Near an AC power outlet close to computers you plan to connect with Ethernet cables and near locations where you use wireless computers For best signal strength the router should be within line of sight of your wireless devices e In an elevated location keeping the number of walls and ceilings between the wireless modem router and your wireless computers to a minimum Away from electrical devices that are potential sources of interference such as ceiling fans home security systems microwaves or the base for a cordless phone To mount the router 1 Drill holes in the wall where you will wall mount the router Holes should be 9 5 in 24 1 cm center to center Figure 56 Drill the holes 2 Put wall anchors in the holes Use pan head Phillips wood screws 3 5 x 20 mm diameter x length European or 6 type screw 1 inch long U S CNM Figure 57 Put wall anchors in the holes Appendix A Supplemental Information 99 N150 Wireless ADSL2 Modem Router DGN1000 User Manual 3 Insert screws into the wall anchors leaving 3 16 in 0 5 cm of each screw exposed Figure 58 Insert screws into the wall anchors 4 For best wireless performance position the wireless antennas as shown with the
15. as described in Setup Wizard on page 24 or manually as described in Manual Setup Basic Settings on page 25 However before you start the setup process you need to have your ISP information on hand and make sure the laptops PCs and other devices in the network have the settings described here Note If you have a Macintosh or Linux system you have to use the manual setup method Use Standard TCP IP Properties for DHCP If you configured your computer to use a static IP address you need to change the settings back so that it uses Dynamic Host Configuration Protocol DHCP See Appendix A Supplemental Information for more information Replace an Existing Router To replace an existing router disconnect it completely from your network and set it aside before starting the router setup Adapters and Security Settings Awireless adapter is the wireless radio in your PC or laptop that lets the PC or laptop connect to a wireless network Most PCs and laptops come with an adapter already installed but if it is outdated or slow you can purchase a USB adapter to plug into a USB port Make sure the wireless adapter in each computer in your wireless network supports the same security settings as the wireless modem router See Preset Security on page 33 for information about the router s preconfigured security settings Note If you connect devices to your modem router using WPS as described in Wi Fi Protected Setup WPS Method on page 36
16. filtering Disabled Wireless Wireless Communication Enabled Wi Fi Network Name SSID Can be found on the router label at the bottom of the unit WPA WPA2 PSK Passphrase Can be found on the router label at the bottom of the unit Broadcast SSID Enabled Transmission Speed Auto Country Region United States in North America otherwise varies by region RF Channel Auto Operating Mode Up to 150 Mbps Data Rate Best Output Power Full Access Point Enabled Authentication Type Pre Shared Key Wireless Card Access List All wireless stations allowed 1 Maximum wireless signal rate derived from IEEE Standard 802 11 specifications Actual throughput will vary Network conditions and environmental factors including volume of network traffic building materials and construction and network overhead lower actual data throughput rate 96 Appendix A Supplemental Information N150 Wireless ADSL2 Modem Router DGN1000 User Manual Technical Specifications Table 8 Technical Specifications Description Network Protocol and Standards Compatibility Data and routing protocols TCP IP RIP 1 RIP 2 DHCP PPPoE or PPPoA RFC 1483 Bridged or Routed Ethernet and RFC 1577 Classical IP over ATM Power Adapter North America 120V 60 Hz input UK Australia 240V 50 Hz input Europe 230V 50 Hz input All regions output 12V AC 1 0A output Physical Dimensions 6 80 in x 5 0
17. have a DSL connection The Internet LED is red when there is no Internet connection Turn on your computer If software usually logs you in to your Internet connection do not run that software Cancel it if it starts automatically Verify that the LAN 1 lights 1 through 4 are lit for any computers cabled to the modem router by an Ethernet cable 16 Chapter 1 Hardware Setup Router Internet Setup Connecting to the Internet This chapter explains how to set up your Internet connection using one of three methods NETGEAR Genie recommended Setup Wizard or manual setup If you have already set up your router using one of these methods the initial router setup is complete Refer to this chapter if you want to become familiar with the router menus view or adjust the initial settings or change the router password and login time out This chapter contains the following sections Router Setup Preparation NETGEAR Genie Setup Log In to the N150 Modem Router Upgrade Router Firmware Router Interface Setup Wizard Manual Setup Basic Settings DSL Settings Unsuccessful Internet Connection Change Password and Login Time Out Log Out Manually Types of Logins Chapter 2 Router Internet Setup 17 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Router Setup Preparation You can set up your wireless modem router with the NETGEAR Genie as described in NETGEAR Genie Setup on page 19 with the Setup Wizard
18. help 1 When power is first applied the Power LED lights 2 After approximately 10 seconds the LAN and DSL LEDs light as follows a The LAN port LEDs light for any local ports that are connected b The DSL link LED lights to indicate that there is a link to the connected device c lf a LAN port is connected to a 100 Mbps device verify that the LAN port s LED is green Note that if the LAN port is 10 Mbps the LED is amber Power LAN Ports 1 4 DSL Internet Wireless Figure 54 Front panel LED Icons Power LED Is Off If the Power and other LEDs are off when your router is turned on e Check that the power cord is correctly connected to your router and the power supply adapter is correctly connected to a functioning power outlet e Check that you are using the 12 V DC power adapter supplied by NETGEAR for this product If the error persists you could have a hardware problem and should contact NETGEAR Technical Support Chapter 7 Troubleshooting 85 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Power LED Is Red When the router is turned on it performs a power on self test If the Power LED turns red after a few seconds or at any other time during normal operation there is a fault within the router If the Power LED turns red to indicate a router fault turn the power off and on to see if the wireless modem router recovers If the power LED is still red 1 minute after power up Turn the power off and
19. modem router to prevent objectionable content from reaching the PCs and other devices connected to your network This chapter contains the following sections e Keyword Blocking of HTTP Traffic Firewall Rules to Control Network Access e Configure Services e Set the Time Zone e Schedule Firewall Services e Enable Security Event Email Notification Chapter 4 Security Settings 44 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Keyword Blocking of HTTP Traffic Use keyword blocking to prevent certain types of HTTP traffic from accessing your network The blocking can be always or according to a scheduled 1 Select Security gt Block Sites Block Sites Keyword Blocking O Never Per Schedule Always Type Keyword or Domain Name Here Add Keyword Block Sites Containing these Keywords or Domain Names C Allow Trusted IP Address to Visit Blocked Sites Trusted IP Address Figure 24 Block inbound traffic based on keywords 2 Select one of the keyword blocking options Per Schedule Turn on keyword blocking according to the Schedule screen settings Always Turn on keyword blocking all the time independent of the Schedule screen 3 In the Keyword field enter a keyword or domain click Add Keyword and click Apply The Keyword list supports up to 32 entries Here are some sample entries e Specify XXX to block http www badstuff com xxx html e Specify com if you want to allow only sites with domain s
20. similar object to press and hold the Restore Factory Settings button for at least 7 seconds The wireless modem router resets and returns to the factory settings Your device will return to the factory configuration settings shown in the following table Table 7 Factory Settings Description Feature Default Behavior Router Login User Login URL http www routerlogin net or http www routerlogin com User Name case sensitive admin Login Password case sensitive password Internet Connection WAN MAC Address Use default address WAN MTU Size 1492 Port Speed AutoSense Local Network LAN Lan IP 192 168 0 1 Subnet Mask 255 255 255 0 RIP Direction None RIP Version Disabled RIP Authentication None DHCP Server Enabled DHCP Starting IP Address 192 168 0 2 DHCP Ending IP Address 192 168 0 254 DMZ Disabled Time Zone GMT Time Zone Adjusted for Daylight Saving Disabled Time SNMP Disabled Appendix A Supplemental Information 95 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Table 7 Factory Settings Description Feature Default Behavior Firewall Inbound communications coming in from Disabled except traffic on port 80 the HTTP port the Internet Outbound communications going out to Enabled all the Internet Source MAC
21. that name linked with your IP address by public Domain Name Servers DNS However if your Internet account uses a dynamically assigned IP address you do not know in advance what your IP address is and the address can change frequently In this case use a commercial Dynamic DNS service that lets you register your domain to its IP address and forwards traffic directed at your domain to your frequently changing IP address The router has a client that can connect to a Dynamic DNS service provider Once you have configured your ISP account information in the router whenever your ISP assigned IP address changes your router contacts your Dynamic DNS service provider logs in to your account and registers your new IP address 1 Select Advanced gt Dynamic DNS to display the following screen Dynamic DNS C Use a Dynamic DNS Service Service Provider www DynDNS org Y Host Name User Name Password Use Wildcards Apply Cancel Show Status Figure 46 Forward traffic to a changing IP address 2 Access the website of one of the Dynamic DNS service providers whose names appear in the Service Provider drop down list and register for an account For example for dyndns org go to www dyndns org 3 Select the Use a Dynamic DNS Service check box 4 Select the name of your Dynamic DNS service provider 5 Type the host name that your Dynamic DNS service provider gave you The Dynamic DNS service provider might call this the dom
22. the PIN number method e While the wireless modem router attempts to connect to a WPS capable device the WPS LED on the front of the wireless modem router blinks green When the wireless modem router establishes a WPS connection the LED is solid green e f a connection is established the wireless modem router WPS screen displays a confirmation message 4 Repeat to add another WPS client to your network Wireless Settings Screen The Wireless Settings screen lets you view or configure the wireless network configuration If you want to make changes note the current settings first Once you have established basic wireless connectivity you can enable security settings appropriate to your needs NETGEAR recommends that you not change the Wi Fi network name SSID WPA WPA2 PAK passphrase or security option but if you want to change these settings this section explains how Note If you use a wireless computer to change the wireless network name SSID or other wireless security settings you are disconnected when you click Apply To avoid this problem use a computer with a wired connection to access the modem router 38 Chapter3 Wireless Settings N150 Wireless ADSL2 Modem Router DGN1000 User Manual Consider Every Device on Your Network Before you begin check the following Every wireless computer has to be able to obtain an IP address by DHCP from the router as described in Use Standard TCP IP Properties for DHCP on p
23. three times when the Restore Factory Settings button is released and then turns green as the gateway resets to the factory defaults Table 2 LAN LED Icon LED Activity Description Solid green The LAN port has detected an Ethernet link with a device d Blinking green Data is being transmitted or received Off No link is detected on this port 10 Chapter 1 Hardware Setup Table 3 DSL LED N150 Wireless ADSL2 Modem Router DGN1000 User Manual Icon LED Activity Description Solid green You have a DSL connection In technical terms the DSL port is NN synchronized with an ISP s network access device Blinking green Indicates that the wireless modem router is negotiating the best possible speed on the DSL line Off The unit is off or there is no IP connection Table 4 Internet LED Icon LED Activity Description Solid green You have an Internet connection If this connection is dropped due to an ce idle time out but the DSL connection is still present the light stays green If the Internet connection is dropped for any other reason the light turns off Solid red The Internet IP connection failed See No Internet Connection on page 87 for troubleshooting information Blinking green Data is being transmitted over the DSL port Off No Internet connection is detected or the device is in bridge mode an external dev
24. type your wireless modem router s WAN IP address in your browser s Address field followed by a colon and the custom port number For example if your external address is 134 177 0 123 at port number 8080 enter the following in your browser http 134 177 0 123 8080 Note The http is required in the address Static Routes Static routes provide additional routing information to your router Under normal circumstances the router has adequate routing information after it has been configured for Internet access and you do not need to configure additional static routes Only configure static routes for unusual cases such when you have multiple routers or multiple IP subnets on your network Static Route Example As an example of when a static route is needed consider the following case e Your primary Internet access is through a cable modem to an ISP e You have an ISDN router on your home network for connecting to the company where you are employed This router s address on your LAN is 192 168 0 100 e Your company s network address is 134 177 0 0 When you first configured your router two implicit static routes were created A default route was created with your ISP as the wireless modem router and a second static route was created to your local network for all 192 168 0 x addresses With this configuration if you attempt to access a device on the 134 177 0 0 network your router forwards your request to the ISP The ISP
25. you might not be familiar with ADSL microfilters If you are you can skip this section and proceed to Cable Your N150 Wireless Modem Router on page 15 An ADSL microfilter is a small in line device that filters DSL interference out of standard phone equipment that shares the same line with your DSL service Every telephone device that connects to a telephone line that provides DSL service needs an ADSL microfilter to filter out the DSL interference Example devices are telephones fax machines answering machines and caller ID displays Note that not every phone line in your home necessarily carries DSL service That depends on the DSL service setup in your home Note Often the ADSL microfilter is included in the box with the wireless modem router If you purchased the wireless modem router in a country where a microfilter is not included you have to acquire the ADSL microfilter separately One Line ADSL Microfilter Plug the ADSL microfilter into the wall outlet and plug your phone equipment into the jack labeled Phone The wireless modem router plugs directly into a separate DSL line Plugging the wireless modem router into the phone jack blocks the Internet connection If you do not have a separate DSL line for the router the best thing to do is to use an ADSL microfilter with a built in splitter see the next paragraph Plugs into DSL line Figure 5 One line ADSL microfilter Second best when you do not have a separate DSL line for
26. your PC enter that host name as the account name in the Basic Settings screen Your ISP could be rejecting the Ethernet MAC addresses of all but one of your PCs Many broadband ISPs restrict access by allowing traffic only from the MAC address of your modem but some additionally restrict access to the MAC address of a single PC connected to that modem In this case configure your router to clone or spoof the MAC address from the authorized PC Cannot Log in If you cannot log in to the wireless modem router from a computer on your local network check the following The router is plugged in and it is on You are using the correct login information The login name is admin and the password is password Make sure that Caps Lock is off when you enter this information If you cannot connect wirelessly try an Ethernet connection and view the router wireless settings and set up your wireless computer with corresponding wireless settings If you are using an Ethernet connected computer check the Ethernet connection between the computer and the router The LAN LED for the port you are using on the router should light up to show your connection Your computer s IP address is on the same subnet as the router If you are using the recommended addressing scheme your computer s address should be in the range 192 168 0 2 to 192 168 0 254 Follow the instructions in the online document that you can access by clicking Preparing Your Network on
27. 0 0c eee eee eee 46 Specify a Trusted Computer suos Eo ER RRPVEOR IER R4 46 Firewall Rules to Control Network Access aaa 46 Configure Firewall Rules 2 2400004000000 eee ee eee Re 46 Inbound Rules Port Forwarding 000620 aaa 48 Outbound Rules Service Blocking 0 eee eee eee 51 Cono SOIVIDOS 2 sa oca ee dee oa ara eon cele dva 52 Setthe TING ZONE iueos ecc RR ERR REOR UAR a Cx RR ww 54 Schedule Firewall Services nuaa naaa eee eee eee eee ee 55 Enable Security Event Email Notification 2 4 56 Chapter 5 Network Maintenance Upgrade the Router Firmware acc cskeese ek tA RE ee eos eee ee SESS 59 Turn Off Automatic Firmwar Checking eee 59 Automatic Firmware Checking On 00 e eee eee 60 Manually Check for Firmware Upgrades 2 20005 61 Manage the Configuration Fei e xax art X REGENT REX GET bad 62 Back I osusssudr wee ROM N RR EY TERES 62 BOSE dzaqacQeqdAqa AR FUddoba SU RA du ANE RRSGSqdaa E RE qud 62 3 A CITED 63 bi Roter DING cm 64 View Attached Devices 2 cece eee ee eh hh hee 68 Run Diagnostie UMS a nG KARA Ep we erbos rein ip ea bka 69 Chapter 6 Advanced Settings MANSE Saab sS RSRESEASu E eran are re er err ema wy Were arr yo rarer 71 Denon OWS nce tere eede kad eee SHEARS hse id R4 KAG 73 LAN SOWD cha 5004 459 b oo e4G Os O4 gt OR OHSS aeee RTE SS 74 Access Router Interface on
28. 3 in x 1 28 in 172 7 mm x 127 7 mm x 32 5 mm Weight 0 61 Ibs 0 275 kg Environmental Operating temperature 0 to 40 C 32 to 104 F Operating humidity 10 to 90 relative humidity noncondensing Storage temperature 20 to 70 C 4 to 158 F Storage humidity 5 to 95 relative humidity noncondensing Regulatory Compliance Meets requirements of FCC Part 15 Class B VCCI Class B EN 55 022 CISPR 22 Class B Interface Specifications LAN 10BASE T or 100BASE Tx RJ 45 WAN DSL Dual RJ 11 pins 2 and 3 71 413 G DMT Appendix A Supplemental Information 97 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Related Documents This table provides links to reference documents you can use to gain a more complete understanding of the technologies used in your NETGEAR product Table 9 Related Documents Document Link TCP IP Networking Basics http docs netgear com reference enu tcpip index htm Preparing Your Network http docs netgear com reference enu wsdhcp index htm Virtual Private Networking Basics http docs netgear com reference enu vpn index htm Wireless Networking Basics http docs netgear com reference enu wireless index htm Glossary htip docs netgear com reference enu glossary index htm 98 Appendix A Supplemental Information N150 Wireless ADSL2 Modem Router DGN1000 User Manual Wall Mount
29. 8 addresses DNS 27 ADSL see also DSL statistics viewing 66 ADSL microfilter cabling described 15 filter described 13 ADSL microfilters 13 ADSL settings 28 ADSLport 9 Advanced Wireless Settings screen 77 alerts emailing 56 Application Level Gateway ALG disabling 73 attached devices viewing 68 automatic firmware checking 59 automatic Internet connection 24 back panel 9 backing up configuration 62 Basic Settings screen described 26 manual setup 25 blocking content and services 44 blocking keywords examples 45 blocking settings examples 45 box contents 7 C cabling Ethernet 16 phone line 15 changes not saved router 92 compliance 101 configuration file backing up 62 erase 63 erasing 63 managing 62 restoring 62 configuration wireless network 38 connecting wirelessly 12 connection Internet 20 content filtering 44 country setting 24 CU SeeMe 49 D date and time 93 daylight savings time 54 93 default demilitarized zone DMZ server 72 default factory settings restoring 63 default factory settings see factory settings deleting configuration 63 denial of service DoS port scans 71 protection 44 devices adding 36 diagnostic utilities 69 disable SSID 34 disabling firewalls 28 SIP ALG 73 SSID broadcast 34 Domain Name Server DNS addresses 27 73 Domain Name Server DNS secondary 27 DSL port LED 11 DSL port settings 65 DSL settings 28 Dynamic DNS 73 Dynamic Host C
30. 89 17 EN301 893 5Ghz EN60950 1 This device is a 2 4 GHz wideband transmission system transceiver intended for use in all EU member states and EFTA countries except in France and Italy where restrictive use applies In Italy the end user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and or for supplying public access to telecommunications and or network services 102 Appendix B Notification of Compliance N150 Wireless ADSL2 Modem Router DGN1000 User Manual This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 2483 5 MHz For detailed information contact the national spectrum authority in France For complete DoC visit the NETGEAR EU Declarations of Conformity website at htip kb netgear com app answers detail a id 11621 Table 10 EDOC in Languages of the European Community Language Statement Cesky Czech NETGEAR Inc timto prohlaSuje Ze tento Radiolan je ve shode se zakladnimi po adavky a dal mi pr slu n mi ustanoven mi smernice 1999 5 ES Dansk Danish Undertegnede NETGEAR Inc erkl rer herved at f lgende udstyr Radiolan Deutsch German overholder de v sentlige krav og vrige relevante krav i direktiv 1999 5 EF Hiermit erkl rt NETGEAR Inc dass sich das Ge
31. AN side of the router Chapter 2 Router InternetSetup 27 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Disable firewall This disables the firewall in addition to disabling NAT With the firewall disabled the protections usually provided to your network are disabled When no login is required this field displays Router MAC Address The Ethernet MAC address used by the wireless modem router on the Internet port Some ISPs register the MAC address of the network interface card in your computer when your account is first opened They will then accept traffic only from the MAC address of that computer This feature allows your wireless modem router to use your computer s MAC address this is also called cloning Use Default Address Use the default MAC address Use Computer MAC Address The wireless modem router will capture and use the MAC address of the computer that you are now using You must be using the one computer that is allowed by the ISP Use This MAC Address Enter the MAC address that you want to use DSL Settings The DSL settings of your wireless modem router work fine for most ISPs However some ISPs use a specific multiplexing method and virtual circuit number for the virtual path identifier VPI and virtual channel identifier VCI Note It is required that you use the Setup Wizard to select the correct country for the default DSL settings to work If your ISP provided you with a multiplexing me
32. Additional Port 76 Use Router as DHCP Server 00 76 Reserved IP Addresses Setup cece eee ee eee 76 4 Contents N150 Wireless ADSL2 Modem Router DGN1000 User Manual Advanced Wireless Settings Remote Management aaa Statie ROUTES o pana BRED A BARA deesetacharetiaaas Static Route Example as csc ase ena eh Configure Static Routes 2 0 0 006 6c eee eee Universal Plug and Play is sogioud dee bd E ERROR Chapter7 Troubleshooting Router OEC ouo bu dorsa do dod Oo qe b Rc Rope NAKA Power EBD IS TT sia eco ob deed Sherk a abd kek ae Power LED B Red Liu uua aceto KAPG ea au ee aoods LAN or DSL Link LED Is Off No Internet Connection 0 0 00 eee eee ic ot MTT EET EE EENE CESTE eee ere Internet LED Is Red ss 4 GN iaa RR 3 dob RA Cannot Obtain an Internet IP Address Debug PPPoE or PPPOA Lo sawa eese s Cannot Load an Internet Web Page TCP IP Network Not Responding Test the LAN Path to Your Wireless Modem Router Test the Path from Your Computer to a Remote Device COM LOG cocri ti cenceee ddd sacnaataaasage Changes Not Saved 2 10 a a ARA PB RR RR RR Firmware Needs to Be Reloaded Incorrect Date or Time 0 02 eee eee Appendix A Supplemental Information Patios OU jcc ANG OSEE CA ERE AMET eae Shee Technical Specifications 2655446444 PERELPER LANA Related
33. Documents 0 0000 cece eee eens Wall Mount Your Router 20000 2 eee Appendix B Notification of Compliance Index Contents 5 Hardware Setup Getting to know your wireless modem router The N150 Wireless ADSL2 Modem Router DGN1000 provides you with an easy and secure way to set up a wireless home network with fast access to the Internet over a high speed digital subscriber line DSL It has a built in DSL modem is compatible with all major DSL Internet service providers lets you block unsafe Internet content and applications and protects the devices PCs gaming consoles and so on that you connect to your home network If you have not already set up your new router using the installation guide that comes in the box this chapter walks you through the hardware setup Chapter 2 Router Internet Setup explains how to set up your Internet connection This chapter contains the following sections Unpack Your New Router Hardware Features Position Your Wireless Router ADSL Microfilters Cable Your N150 Wireless Modem Router Verify the Cabling Chapter 1 Hardware Setup 6 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Unpack Your New Router Your box should contain the following items e N150 Wireless ADSL2 Modem Router DGN1000 AC power adapter plug varies by region e Category 5 Cat 5 Ethernet cable Telephone cable with RJ 11 connector e Microfilters and splitt
34. Ds on the router front panel to make sure that the modem router is plugged into an electrical outlet its power is on and the Ethernet cable between your computer and the router is connected to a LAN port Chapter 2 Router Internet Setup 21 N150 Wireless ADSL2 Modem Router DGN1000 User Manual 2 f you connected the Ethernet cable and quickly launched your browser and typed in the router URL your computer might need a minute or two to recognize the LAN connection Relaunch your browser and try again 3 If you are having trouble accessing the router wirelessly NETGEAR recommends that during setup you use an Ethernet cable to connect your computer so that you can log in to the wireless modem router Note If you cannot connect to the wireless router check the Internet Protocol TCP IP properties in the Network Connections section of your PC Control Panel They should be set to obtain both IP and DNS server addresses automatically See your computer documentation or follow the links in Related Documents on page 98 for assistance Upgrade Router Firmware When you log in and if you are connected to the Internet the Firmware Upgrade Assistant screen displays so you can upgrade to the latest available firmware See Chapter 5 Network Maintenance for more information about upgrading firmware 1 Click Yes to check for new firmware recommended The modem router checks the NETGEAR database for new firmware 2 If no new firmware i
35. Enabled Show Statistics Connection Status Figure 39 View the account firmware port and modem status Fill in the fields as follows Account Name The host name assigned in the Basic Settings screen Firmware Version The firmware version 64 Chapter5 Network Maintenance N150 Wireless ADSL2 Modem Router DGN1000 User Manual ADSL Port MAC Address The Ethernet MAC address of the DSL port IP Address The DSL port IP address If no address is shown the wireless modem router cannot connect to the Internet Network Type The value depends on your ISP IP Subnet Mask The DSL port IP subnet mask Gateway IP Address The IP address used as a gateway to the Internet for computers configured to use DHCP Domain Name Server The wireless modem router DNS server IP addresses These addresses are usually obtained dynamically from the ISP LAN Port Local Ports MAC Address The wireless modem router LAN port Ethernet MAC address IP Address The wireless modem router LAN port IP address The default is 192 168 0 1 DHCP If Off the wireless modem router does not assign IP addresses to PCs on the LAN If On the wireless modem router does assign IP addresses to PCs on the LAN IP Subnet Mask The IP subnet mask used by the wireless modem router LAN The default is 255 255 255 0 Modem ADSL Firmware Version The version of the firmware Modem Status The connection status of the modem DownStream Connection Speed T
36. Firmware Upon Log in Cancel Figure 34 Check for Updated Firmware Upon Log in check box Chapter 5 Network Maintenance 59 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Automatic Firmware Checking On When automatic firmware checking is on the wireless modem router performs the check and notifies you if an upgrade is available or not as shown here Firmware Upgrade Assistant Firmware Version Check A New Firmware Version is Found No New Firmware Version Available Do You Want to Upgrade to the New Version Now Current Version 1 0 3 5 Back New Version Figure 35 Firmware upgrade assistant and results screen 1 Click Yes to allow the wireless modem router to download and install the new firmware The upgrade process could take a few minutes When the upload is complete your wireless modem router restarts 2 Go to the DGN1000 support page at http www netgear com support and read the new firmware release notes to determine whether you need to reconfigure the modem router after upgrading Note If you get a Firmware needs to be reloaded message it means a problem has been detected with the router s firmware Follow the prompts to correct the problem or see Firmware Needs to Be Heloaded on page 92 for a description of the steps 60 Chapter 5 Network Maintenance N150 Wireless ADSL2 Modem Router DGN1000 User Manual Manually Check for Firmware Upgrades You can use the Router Upgrade sc
37. NETGEAR N150 Wireless ADSL2 Modem Router DGN 1000 User Manual N150 Wireless ADSL2 Modem Router DGN1000 User Manual 2011 NETGEAR Inc All rights reserved No part of this publication may be reproduced transmitted transcribed stored in a retrieval system or translated into any language in any form or by any means without the written permission of NETGEAR Inc Technical Support Thank you for choosing NETGEAR To register your product get the latest product updates or get support online visit us at http support netgear com Phone US amp Canada only 1 888 NETGEAR Phone Other Countries See Support information card Trademarks NETGEAR the NETGEAR logo ProSafe Smart Wizard NETGEAR genie and Auto Uplink are trademarks or registered trademarks of NETGEAR Inc Microsoft Windows Windows NT and Vista are registered trademarks of Microsoft Corporation Other brand and product names are registered trademarks or trademarks of their respective holders Statement of Conditions To improve internal design operational function and or reliability NETGEAR reserves the right to make changes to the products described in this document without notice NETGEAR does not assume any liability that may occur due to the use or application of the product s or circuit layout s described herein Revision History Publication Part Number Version Publish Date Comments 202 10523 03 v1 0 Jan 2011 C
38. PC operating system router serial number and WAN Port MAC Address See Restrict Access by MAC Address on page 34 for more information about MAC addresses 20 Chapter2 Router Internet Setup N150 Wireless ADSL2 Modem Router DGN1000 User Manual Log In to the N150 Modem Router Log in to the wireless modem router to view or change settings or to set up the wireless modem router 1 Type http 192 168 0 1 in the address field of your browser and press Enter to display the login window You can also enter either of these addresses to access the wireless modem router http www routerlogin net or http www routerlogin com http 192 168 0 1 User name admin Password dokekckeiekelek Remember my password TUM Figure 10 Enter the user name and password 2 When prompted enter admin for the router user name and password for the router password both in lowercase letters Note The router user name and password are probably different from the user name and password for logging in to your Internet connection See Types of Logins on page 31 for more information The router menus display where you can do things like change settings or add other devices to your network See Router Interface on page 23 for a brief description of the available functionality and Wi Fi Protected Setup WPS Method on page 36 for information about adding devices to your network If you do not see the login prompt 1 Check the LE
39. Up to 65 Mbps supports up to 65 Mbps Wireless Access Point Settings Enable When this check box is not selected the wireless signal in the router so it can accept wireless clients When not enabled the router accepts wired clients only This check box is selected by default Allow Broadcast of Name SSID This setting allows the wireless modem router to broadcasts its SSID so wireless stations can see this wireless name SSID in its scanned network list This check box is selected by default To turn off the SSID broadcast clear the Allow Broadcast of Name SSID check box and click Apply Wireless Isolation When this check box is selected wireless stations cannot communicate with each other or with stations on the wired network This check box is not selected by default Wireless Station Access List Settings The Wireless Stations Access List lets you restrict access to your network to a specific list of devices based on their MAC addresses This section explains how to set up the list 1 On the Wireless Settings screen click the Setup Access List button to display the Wireless Station Access List screen shown in Figure 19 Wireless Station Access List and introduced here 40 Chapter 3 Wireless Settings N150 Wireless ADSL2 Modem Router DGN1000 User Manual e The Turn Access Control On check box at the top is not selected by default to allow any computer configured with the correct wireless network name SSID and pass
40. a or transmitter FCC Declaration of Conformity We NETGEAR Inc 350 East Plumeria Drive San Jose CA 95134 declare under our sole responsibility that the N150 Wireless ADSL2 Modem Router DGN1000 complies with Part 15 Subpart B of FCC CFR47 Rules Operation is subject to the following two conditions This device may not cause harmful interference and This device must accept any interference received including interference that may cause undesired operation FCC Radio Frequency Interference Warnings amp Instructions This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following methods Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an electrical outle
41. a passphrase to perform the authentication and generate the initial data encryption keys Then it dynamically varies the encryption key WPA PSK uses Temporal Key Integrity Protocol TKIP data encryption implements most of the IEEE 802 11i standard and is designed to work with all wireless network interface cards but not all wireless access points It is superseded by WPA2 PSK e WPA2 PSK is the strongest It is advertised to be theoretically indecipherable due to the greater degree of randomness in encryption keys that it generates WPA2 PSK gets higher speed because it is usually implemented through hardware while WPA PSK is usually implemented through software WPA2 PSK uses a passphrase to authenticate and generate the initial data encryption keys Then it dynamically varies the encryption key WPS PSK WPA2 PSK Mixed Mode is the preconfigured security mode on the wireless modem router NETGEAR recommends mixed mode because it provides broader support for all wireless clients WPA2 PSK clients get higher speed and security and WPA PSK clients get decent speed and security The product documentation for your wireless adapter and WPA client software should have instructions about configuring their WPA settings e WPA 802 1x is enterprise level security and requires an authentication server to recognize and authorize client access The authentication server is called Remote Authentication Dial In User Service RADIUS Every wireless client
42. age 18 e Each computer or wireless adapter in your network is required to have the same SSID and wireless mode bandwidth data rate as the router Check that the wireless adapter on each computer can support the mode and security option you want to use e The security option on each wireless device in the network is required to match the router For example if you select a security option that requires a passphrase be sure to use same passphrase for each wireless computer in the network View or Change Wireless Settings Your preset router comes set up with a unique wireless network name SSID and network password This information is printed on the label for your router You view or change these settings in the Wireless Settings screen 1 Select Setup gt Wireless Settings to display the following screen Wireless Settings Wireless Network Name SSID NETGEAR Region Europe Channel Auto Mode Up to 150Mbps Wireless Access Point v Enable Wireless Access Point Allow Broadcast of Name SSID Wireless Isolation Wireless Station Access List Setup Access List Security Options O Disable O WEP Wired Equivalent Privacy O WPA PSK Wi Fi Protected Access Pre Shared Key O WPA2 PSK Wi Fi Protected Access 2 with Pre Shared Key 9 Mixed WPA PSK WPA2 PSK O WPA 802 1x WPA2 PSK Security Encryption Network Key 8 63 characters mypassphrase Figure 18 Wireless Settings scr
43. ain name If your URL is myName dyndns org then your host name is myName 6 Type the user name for your Dynamic DNS account 7 Type the password or key for your Dynamic DNS account Chapter 6 Advanced Settings 73 N150 Wireless ADSL2 Modem Router DGN1000 User Manual 8 If your Dynamic DNS provider allows the use of wildcards in resolving your URL you can select the Use Wildcards check box to activate this feature For example the wildcard feature causes yourhost dyndns org to be aliased to the same IP address as yourhost dyndns org 9 Click Apply to save your settings Note If your ISP assigns a private WAN IP address such as 192 168 x x or 10 x x x the Dynamic DNS service will not work because private addresses are not routed on the Internet LAN Setup The LAN Setup screen allows configuration of LAN IP services such as DHCP and Routing Information Protocol RIP The wireless modem router is shipped preconfigured to use private IP addresses on the LAN side and to act as a DHCP server The wireless modem router s default LAN IP configuration is as follows e LANIP address 192 168 0 1 e Subnet mask 255 255 255 0 These addresses are part of the private address range designated by the Internet Engineering Task Force IETF htip www ietf org for use in private networks and should be suitable in most applications If your network has a requirement to use a different IP addressing scheme you can make those chang
44. al Setup Basic Settings described on 25 24 Chapter2 Router Internet Setup N150 Wireless ADSL2 Modem Router DGN1000 User Manual Manual Setup Basic Settings The Basic Settings screen displays when you select No want to configure the Router myself in the Setup Wizard and is also available from the router menus It is where you view or change ISP information The fields that display vary depending on whether or not your Internet connection requires a login Note Check that the country and language are set as described Setup Wizard on page 24 before proceeding with the manual setup 1 Select Set Up gt Basic Settings and select Yes or No depending on whether or not your ISP requires a login Figure 13 Basic Settings screen without left and with right login shows both forms of the Basic Settings screen e Yes Select the encapsulation method and enter the login name If you want to change the login time out enter a new value in minutes e No Enter the account and domain names as needed 2 Enter the settings for the IP address and DNS server The default DSL settings usually work fine If you have problems with your connection check the DSL settings and see DSL Settings on page 28 for more information 3 If no login is required you can specify the MAC Address setting 4 Click Apply to save your settings 5 Click Test to test your Internet connection If the NETGEAR website does not appear within 1 minute
45. and if so what type of security is configured WPS Settings Router s PIN The PIN number that you use on a registrar for example from the Network Explorer on a Vista Windows PC to configure the wireless modem router s wireless settings through WPS You can also find the PIN on the wireless modem router s product label The PIN function might temporarily be disabled when the wireless modem router detects suspicious attempts to break into the wireless modem router s wireless settings by using the wireless modem router s PIN through WPS You can manually enable the PIN function by clearing the Disable Router s PIN check box Keep Existing Wireless Settings By default the Keep Existing Wireless Settings check box is selected This allows the modem router to keep the same SSID and wireless security settings when WPS enabled devices are added to the network If the Keep Existing Wireless Settings check box is not selected the next time you use WPS to connect WPS capable devices to your wireless network the modem router generates a new random SSID and WPA WPA2 passphrase NETGEAR does not recommend this 78 Chapter6 Advanced Settings N150 Wireless ADSL2 Modem Router DGN1000 User Manual Remote Management The Remote Management screen lets you allow a user or users on the Internet to configure upgrade and check the status of your wireless modem router 1 Select Advanced gt Remote Management to display this screen
46. ation The firmware setting is not accessible by the end user Canadian Department of Communications Radio Interference Regulations This digital apparatus N150 Wireless ADSL2 Modem Router DGN1000 does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications Industry Canada statement T This device complies with RSS 210 of the Industry Canada Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Radiation Exposure Statement This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body This device has been designed to operate with an antenna having a maximum gain of 5 59 dB Antenna having a higher gain is strictly prohibited per regulations of Industry Canada The required antenna impedance is 50 ohms Europe EU Declaration of Conformity CEO Marking with the above symbol indicates compliance with the Essential Requirements of the R amp TTE Directive of the European Union 1999 5 EC This equipment meets the following conformance standards EN300 328 2 4Ghz EN301 4
47. ation Success Authentication Success Getting IP Addresses 69 110 231 81 Getting Network Mask 255 255 255 255 Close Window Figure 41 View connection status information Fill in the fields as follows Connection Time The time elapsed since the last connection to the Internet through the DSL port Connecting to sender The connection status Negotiation Success or Failed Authentication Success or Failed Obtaining IP Address The IP address assigned to the WAN port by the ISP Obtaining Network Mask The network mask assigned to the WAN port by the ISP Chapter 5 Network Maintenance 67 N150 Wireless ADSL2 Modem Router DGN1000 User Manual View Attached Devices The Attached Devices screen presents a table of all IP devices that the wireless modem router has discovered on the local network Select Maintenance gt Attached Devices to view the following table Attached Devices ZIP Address Device Name MAC Address 1192 168 0 2 9300UNIT2 00 11 43 71 D1 92 Figure 42 Table of all devices attached to the local network For each device the table shows the IP address device name if available and the Ethernet MAC address Note that if the wireless modem router is rebooted the table data is lost until the wireless modem router rediscovers the devices To force the wireless modem router to look for attached devices click the Refresh button 68 Chapter 5 Network Maintenance N150 Wireless ADSL2 Modem Rou
48. backed up the wireless modem router settings previously you should do a new backup so that the saved settings file includes the new password See Back Up on page 62 for information about backing up your network configuration 30 Chapter2 Router Internet Setup N150 Wireless ADSL2 Modem Router DGN1000 User Manual Log Out Manually The router interface provides a Logout command at the bottom of the router menus Log out when you expect to be away from your computer for a relatively long period of time Types of Logins There are three separate types of logins that have different purposes It is important that you understand the difference so that you know which login to use when Router login logs you in to the router interface See Log In to the N150 Modem Router on page 21 for details about this login ISP login logs you in to your Internet service Your service provider has provided you with this login information in a letter or some other way If you cannot find this login information contact your service provider Wi Fi network name and passphrase logs you in to your wireless network This login is preconfigured and can be found on the label on the bottom of your unit See Chapter 3 Wireless Settings for more information Chapter 2 Router Internet Setup 31 Wireless Settings Protecting your network This chapter describes how to use the Wireless Settings screens to view and change if needed your wireless net
49. d Diagnostics Figure 11 Router menus Basic Settings screen and online help e Setup Wizard Specify the language location and automatically detect the Internet connection See Setup Wizard on page 24 Add WPS Client Add WPS compatible wireless devices and other equipment to your wireless network See Add Clients Devices to Your Network on page 36 e Setup Menu Set upgrade and check the ISP and wireless network settings of your router See Manual Setup Basic Settings on page 25 and DSL Settings on page 28 See also Chapter 3 Wireless Settings for information about preset and basic security settings e Security Menu View and configure the router firewall settings to prevent objectionable content from reaching your PCs See Chapter 4 Security Settings e Maintenance Menu Administer and maintain your router and network See Chapter 5 Network Maintenance Advanced Menu Set the router up for unique situations such as when remote access by IP or by domain name from the Internet is needed See Chapter 6 Advanced Settings Using this menu requires a solid understanding of networking concepts e Web Support Go to the NETGEAR support site to get information help and product documentation These links work once you have an Internet connection Chapter 2 Router Internet Setup 23 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Setup Wizard If you do not use the NETGEAR Genie you have to log in to the m
50. e 43 TCP IP Basics link to doc 98 when to use 35 technical specifications 97 wireless access points 40 technical support 2 wireless adapter 18 Temporal Key Integrity Protocol TKIP 35 wireless advanced settings 77 terms 98 wireless channel 40 time of day 93 wireless connections 12 time zone setting 54 wireless connectivity 34 time stamping 54 wireless isolation 40 traffic log 49 Wireless LAN WLAN 66 troubleshooting 84 wireless LED 11 cannot log in 91 wireless mode 40 date or time incorrect 93 wireless network configuration 38 firmware reload 92 wireless network name 8 ee wireless network settings 40 router changes not saved 92 wireless port settings 65 router not on 85 wireless region 40 trusted host 46 wireless security 33 Trusted IP Address field 46 wireless security options 34 trusted wireless stations 41 Wireless Settings screen 38 turn off wireless connectivity 34 wireless settings SSID broadcast 40 two line ADSL microfilter 14 Wireless Stations Access List 40 WPA encryption 35 U WPA2 encryption 35 WPA2 PSK encryption 35 Universal Plug and Play UPnP 82 WPA 802 1x encryption 35 upgrading firmware 59 80 passphrases 42 RADIUS servers 35 V WPA PSK encryption 35 WPA PSK WPA2 PSK mixed mode 35 WPS button 37 WPS LED 11 WPS see Wi Fi Protected Setup WPS WPS capable devices 36 Virtual Channel Identifier VCI 19 28 Virtual Path Identifier VPI 19 28 Virtual Private Network VPN basics 98 W WPS PSK encryptio
51. e firmware 22 login time out 30 logs emailing 56 logs traffic 49 MAC address product label 8 MAC addresses described 34 filtering by 41 rejected 91 restricting access by 41 43 spoofing 88 maintenance settings 58 manual logout 31 manual setup 25 106 Index N150 Wireless ADSL2 Modem Router DGN1000 User Manual manual setup Basic Settings screen 25 Maximum Transmit Unit MTU 72 menus described 23 metric number of routers 82 mixed mode security options 35 modem settings status 65 multicasting 76 N NETGEAR Genie 19 Network Address Translation NAT 27 76 Network Time Protocol NTP 54 93 network troubleshooting 89 networks controlling access 46 no Internet connection 29 O On Off button 9 On Off LED 10 one line ADSL microfilter 13 online help router 23 outbound firewall rules 51 P passphrase product label 8 passphrases 43 changing 42 WPA 802 1x 42 passwords see passphrases phone line cabling 15 pinging WAN port 72 Plug and Play Universal UPnP 82 plug and play universal UPnP 82 Point to Point over Ethernet PPPoE enabling relay 71 WAN port setting default 20 Point to Point Tunneling Protocol PPTP 24 port numbers 52 port scanning disabling 71 ports filtering 51 forwarding 48 Instant Messaging 47 listed back panel 9 positioning the router 12 power adapter AC 9 preset security about 33 passphrase 33 42 security option 33 SSID 33 pre shared key 35
52. e one below telling you that you need to reload the router s firmware This means a problem has been detected with the router s firmware Your Netgear DSL Gateway has detected that s firmware needs to be reloaded o reload amp rmware please follow these steps 1 Obtain the firmware to load from the firmware loaded on your PC dunng setup with the Setup Wizard CD default from the Setup CD or from the Netgear support site and place it in a folder on your PC E se to the firmware or enter the path m the box below Upgrade 4 The upgrade process will take about 5 minutes wait for the Progress Bar to complete 5 The Router Management Interface log in prompt will then appear so you can log m to check the status Software file name Browse If you used the Setup CD the PC that you used should have a firmware load at C Figure 55 Reload firmware 1 If you already have the firmware file on your PC go directly to step 2 If you do not have the firmware file on your PC obtain the firmware from the NETGEAR support site at http www netgear com support through another working Internet connection 2 Click Browse 3 Navigate to the firmware file 92 Chapter 7 Troubleshooting N150 Wireless ADSL2 Modem Router DGN1000 User Manual 4 Click Upgrade A progress bar displays The reload takes about 5 minutes to complete When the firmware recovery is completed the login screen displays so you can log in Incorrect Date or Time Se
53. e the factory default settings Click the Erase button to reset the wireless modem router to its factory default settings Alternately press the Wireless On Off and WPS buttons on the side panel of the wireless modem router simultaneously for 6 seconds Erase sets the user name to admin the password to password the LAN IP address to 192 168 1 1 and enables the wireless modem router s DHCP To restore the factory default configuration settings when you do not know the login password or IP address use the restore factory settings button on the bottom of the router see Factory Settings on page 95 Chapter 5 Network Maintenance 63 N150 Wireless ADSL2 Modem Router DGN1000 User Manual View Router Status Select Maintenance gt Router Status to display the following screen The Router Status screen provides the status and usage information described in the following figure Router Status Account Name Firmware Version 1 00 10_ww ADSL Port MAC Address 00 C0 02 65 43 21 IP Address Network Type PPPoA IP Subnet Mask Gateway IP Address Domain Name Server LAN Port MAC Address 00 00 02 65 43 20 IP Address 192 168 0 1 DHCP on IP Subnet Mask 255 255 255 0 Modem ADSL Firmware Version 3 4 3121 1 Modem Status Link down DownStream Connection Speed 0 kbps UpStream Connection Speed 0 kbps 0 38 Wireless Port Region Europe Channel 11 WLAN1 Name SSID NETGEAR4S Wireless AP Enabled Broadcast Name
54. ect to your network There are two types of encryption Wired Equivalent Privacy WEP and Wi Fi Protected Access WPA WPA is stronger and therefore recommended over WEP WPA has several options including pre shared key PSK encryption and 802 1x encryption for enterprises This section presents an overview of the security options and provides guidance on when to use which option Note that it is also possible to disable wireless security NETGEAR does not recommend this 34 Chapter 3 Wireless Settings N150 Wireless ADSL2 Modem Router DGN1000 User Manual WEP Encryption WEP uses an old encryption method and can be easily decoded with today s powerful computers Use this mode only when you have a very old legacy wireless client that does not support WPA PSK The Wi Fi alliance highly recommends against using WEP and plans to make it obsolete If you do decide to use WEP see Set WEP Encryption and Passphrase on page 43 for the procedure WPA Encryption WPA encryption is built into all hardware that has the Wi Fi certified seal This seal means the product is authorized by the Wi Fi Alliance http www wi fi org because it complies with the worldwide single standard for high speed wireless local area networking For information about how to use the WPA home options see Change WPA Security Option and Passphrase on page 42 WPA PSK uses a much stronger encryption algorithm than WEP so it is harder to decode This option uses
55. ed to increase this value a little UPnP Portmap Table The UPnP Portmap Table displays the IP address of each UPnP device that is currently accessing the wireless modem router and which ports internal and external that device has opened The UPnP Portmap Table also displays what type of port is opened and if that port is still active for each IP address 3 To save cancel your changes or refresh the table e Click Apply to save the new settings to the wireless modem router e Click Cancel to disregard any unsaved changes e Click Refresh to update the portmap table and to show the active ports that are currently opened by UPnP devices Chapter 6 Advanced Settings 83 Troubleshooting Diagnosing and solving problems This chapter provides information to help you diagnose and solve problems you might have with your wireless modem router If you do not find the solution here check the NETGEAR support site at htto support netgear com for product and contact information This chapter contains the following sections Router Not On No Internet Connection TCP IP Network Not Responding Cannot Log in Changes Not Saved Firmware Needs to Be Reloaded Incorrect Date or Time Chapter 7 Troubleshooting 84 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Router Not On When you turn the power on the power LAN and DSL LEDs should light as described here If they do not refer to the sections that follow for
56. ed your line correctly and your wiring is correct DSL Link LED Is Blinking Amber Your wireless modem router is attempting to make a DSL connection with the service provider The LED should turn green within several minutes If the DSL link LED does not turn green disconnect all telephones on the line If this solves the problem reconnect the telephones one at a time and use a microfilter on each telephone as described in ADSL Microfilters on page 13 If you connect the microfilters correctly you should be able to connect all your telephones If disconnecting telephones does not result in a green DSL link LED there might be a problem with your wiring If the telephone company has tested the DSL signal at your network interface device NID you might have poor quality wiring in your house DSL Link LED Is Off First disconnect all telephones on the line If this solves the problem reconnect the telephones one at a time and use a microfilter on each telephone If the microfilters are connected correctly you should be able to connect all your telephones If disconnecting telephones does not result in a green DSL link LED check for the following e Check that the telephone company has made the connection to your line and tested it e Verify that you are connected to the correct telephone line If you have more than one phone line be sure that you are connected to the line with the DSL service It could be necessary to use a swapper i
57. een 2 Make any changes that are needed and click Apply when done to save your settings Chapter 3 Wireless Settings 39 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Note The screen sections settings and procedures are explained in the following sections 3 After you finish adjusting settings and click Apply configure and test your computers for wireless connectivity a Program the wireless adapter of your computers to have the same SSID and channel that you specified in the router b Check that the adapters have a wireless link and can obtain an IP address by DHCP from the wireless modem router Wireless Network Settings Name SSID The SSID is also known as the wireless network name Enter a 32 character maximum name in this field This field is case sensitive The default SSID is randomly generated and NETGEAR strongly recommends that you not change this Region The location where the wireless modem router is used It might not be legal to operate the wireless modem router in a region other than the regions listed Channel The wireless channel used by the gateway 1 through 13 Do not change the channel unless you experience interference shown by lost connections or slow data transfers If this happens experiment with different channels to see which is the best Mode Up to 150 Mbps is the default and allows 802 11n and 802 11g wireless devices to join the network g 4 b supports up to 54 Mbps
58. er IP addresses are assigned to the attached PCs from a pool of addresses specified in this screen Each pool address is tested before it is assigned to avoid duplicate addresses on the LAN For most applications the default DHCP and TCP IP settings of the router are satisfactory Click the link to the online document TCP IP Networking Basics on page 98 for an explanation of DHCP and information about how to assign IP addresses for your network Reserved IP Addresses Setup When you specify a reserved IP address for a computer on the LAN that computer always receives the same IP address each time it accesses the routers DHCP server Reserved IP addresses should be assigned to servers that require permanent IP settings To reserve an IP address 1 Select Advanced LAN Setup and click the Add button 2 In the IP Address field type the IP address to assign to the computer or server Choose an IP address from the router s LAN subnet such as 192 168 0 x 3 Type the MAC address of the computer or server Tip If the computer is already present on your network copy its MAC address from the Attached Devices screen and paste it here 4 Click Apply to enter the reserved address into the table 76 Chapter6 Advanced Settings N150 Wireless ADSL2 Modem Router DGN1000 User Manual Note The reserved address is not assigned until the next time the computer contacts the routers DHCP server Reboot the computer or access its IP con
59. ers quantity and type vary by region e Resource CD with NETGEAR Genie setup Installation guide with cabling and router setup instructions If any of the parts are incorrect missing or damaged contact your NETGEAR dealer Keep the carton including the original packing materials in case you need to return the product for repair See Position Your Wireless Router on page 12 for information about where to place and how to position your router cw C nlt tet Splitter Figure 1 Review the box contents Chapter 1 HardwareSetup 7 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Hardware Features Before you cable your router take a moment to become familiar with the label and the front and back panels Pay particular attention to the LEDs on the front panel Label The label on the bottom of the wireless modem router shows the router s factory reset button security PIN preset login information MAC address and serial number Security PIN Preset login information MAC address Power bh e NETGEAR 150 Wireless MODEM Router DGN1000 Restore Factory Settings Serial number Figure 2 Information on the router label See Preset Security on page 33 for information about preset security and MAC addresses See Factory Settings on page 95 for information about the Reset Factory Settings button and the factory setting values 8 Chapter 1 Hardware Setup N150 Wireless ADSL2 Modem Router DGN1000 Use
60. es in the LAN IP Setup screen Note If you change the LAN IP address of the wireless modem router while connected through the browser you are disconnected To reconnect open a new connection to the new IP address and log in 74 Chapter6 Advanced Settings N150 Wireless ADSL2 Modem Router DGN1000 User Manual 1 Select Advanced gt LAN Setup LAN Setup LAN TCPAP Setup IP Address IP Subnet Mask RIP Direction None v RIP Version RIP 1 v Access Router Management Interface on additional port NAT disabled mode only 7 Use Router as DHCP Server Starting IP Address Ending IP Address Address Reservation IP Address Device Name MAC Address Add Edit Delete Apply Cancel Figure 47 Configure LAN IP services 2 Enter the LAN Setup configuration and click Apply to save your changes IP Address The LAN IP address of the wireless modem router IP Subnet Mask The LAN subnet mask of the wireless modem router Combined with the IP address the IP subnet mask allows a device to know which other addresses are local to it and which have to be reached through a gateway or wireless modem router RIP Direction RIP allows a wireless modem router to exchange routing information with other routers The RIP Direction selection controls how the wireless modem router sends and receives RIP packets The default setting is Both When set to Both or Out Only the wireless modem router broadcasts its routing table
61. es screen see View Attached Devices on page 68 into the MAC Address field To do this configure each wireless computer to obtain a wireless link to the wireless modem router The computer should then appear in the Attached Devices screen 6 Click Apply to save your settings and return to the Wireless Settings screen Chapter 3 Wireless Settings 41 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Security Options Settings The Security Options section of the Wireless Settings screen lets you change the security option and passphrase See Wireless Security Options on page 34 for an explanation of the security options and when to use which one Please note that NETGEAR recommends that you not change the security option or passphrase but if you want to change these settings this section explains how Do not disable security Change WPA Security Option and Passphrase 1 In the Security Options section select the WPA option you want Security Options Disable O WEP Wired Equivalent Privacy WPA PSK Wi Fi Protected Access Pre Shared Key WPA2 PSK Wi Fi Protected Access 2 with Pre Shared Key Mixed WPA PSK WPA2 PSK O WPA 802 1x Figure 20 Mixed WPA2 PSK WPA2 PSK security encryption 2 Inthe Network Key field that displays when you select a WPA security option enter the network key passphrase that you want to use It is a text string from 8 to 63 characters WPA2 PSK Security Encryption Network
62. f you use an outgoing mail server provided by your current ISP you do not need to select this field If you use an email account that is not 56 Chapter 4 Security Settings N150 Wireless ADSL2 Modem Router DGN1000 User Manual provided by your ISP select this field and enter the required user name and password information Send E Mail alerts immediately Select the corresponding check box if you would like immediate notification of a significant security event such as a known attack port scan or attempted access to a blocked site Send Logs According to this Schedule Specifies how often to send the logs Hourly Daily Weekly or When Full Day for sending logs specifies which day of the week to send the log This is relevant when the log is sent weekly Time for sending log specifies the time of day to send the log This is relevant when the log is sent daily or weekly Note If the Weekly Daily or Hourly option is selected and the log fills up before the specified period the log is automatically emailed to the specified email address After the log is sent it is cleared from the wireless modem router s memory If the wireless modem router cannot email the log file the log buffer might fill up In this case the wireless modem router overwrites the log and discards its contents Chapter 4 Security Settings 57 Network Maintenance Administering your network This chapter describes the wireless modem
63. f your DSL signal is on pins 1 and 4 or the RJ 11 jack The wireless modem router uses pins 2 and 3 Chapter 7 Troubleshooting 87 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Internet LED Is Red If the Internet LED is red the device could not connect to the Internet Verify the following e Check that your log in credentials are correct See Log In to the N150 Modem Router on page 21 for more information e Check that the information you entered on the Basic Settings screen is correct See Manual Setup Basic Settings on page 25 e Check with your ISP to verify that the multiplexing method VPI and VCI settings on the DSL settings screen are correct Find out if the ISP is having a problem If it is wait until that problem is cleared up and try again Cannot Obtain an Internet IP Address If your wireless modem router cannot access the Internet and your Internet LED is green or blinking green check whether the wireless modem router can obtain an Internet IP address from the ISP Unless you have been assigned a static IP address your wireless modem router has to request an IP address from the ISP You can determine whether the request was successful as follows 1 Access the router menus at htitp 192 168 0 1 and log in 2 Under Maintenance select Router Status and check that an IP address shows for the WAN port If 0 0 0 0 shows your wireless modem router has not obtained an IP address from your ISP
64. figuration to force a DHCP release and renew To edit or delete a reserved address entry 1 Click the button next to the reserved address that you want to edit or delete 2 Click Edit or Delete Advanced Wireless Settings 1 Select Advanced gt Wireless Settings to display the following screen Advanced Wireless Settings WLAN Name SSID NETGEAR Region Europe Channel 11 Wireless AP enable Broadcast Name enable Security No security WPS Settings Router s PIN 94229882 Disable Router s PIN C Keep Existing Wireless Settings Apply Cancel Figure 48 Configure advanced wireless settings Note The advanced WPS settings section is not displayed if you selected WEP as the security option 2 If you make changes click Apply Note that the WLAN settings come from the settings you made in the Wireless Settings Screen on page 38 WLAN Name SSID The service set ID also known as the wireless network name Region The country where the unit is set up for use Channel The current channel which determines the operating frequency Chapter 6 Advanced Settings 77 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Wireless AP Indicates if the access point feature is enabled If disabled the Wireless LED on the front panel is off Broadcast Name Indicates if the wireless modem router is configured to broadcast its SSID Security Indicates if security is configured on the wireless modem router
65. forwards your request to the company where you are employed and the request is likely to be denied by the company s firewall In this case you have to define a static route telling your router that 134 177 0 0 should be accessed through the ISDN router at 192 168 0 100 The static route setup would look like Figure 51 Add static routes In this example The Destination IP Address and IP Subnet Mask fields specify that this static route applies to all 134 177 x x addresses 80 Chapter6 Advanced Settings N150 Wireless ADSL2 Modem Router DGN1000 User Manual The Gateway IP Address field specifies that all traffic for these addresses are to be forwarded to the ISDN router at 192 168 0 100 e The value in the Metric field represents the number of routers between your network and the destination This is a direct connection so it can be set to the minimum value of 2 The Private check box is selected only as a precautionary security measure in case RIP is activated Configure Static Routes 1 Select Advanced gt Static Routes to display the following screen Static Routes Active Name Destination Gateway Figure 50 View additional routing information 2 To add a static route a Click Add to open the following screen Static Routes Route Name Private Active Destination IP Address 134 177 IP Subnet Mask 255 255 Gateway IP Address 192 Metric 2 Figure 51 Add static routes b
66. g security To use WPS make sure that all wireless devices to be connected to the network are Wi Fi certified and support WPS During the connection process the client gets the security settings from the router so that every device in the network has the same security settings Note However if you find that the router is generating new security settings for each added device it means that the default value for Keep Existing Wireless Settings has changed See WPS Settings on page 78 for more information about this setting All Wi Fi certified and WPS capable products are compatible with the NETGEAR products that have Push N Connect which is based on WPS For information about how to view a list of all wireless and wired devices connected to your modem router see View Attached Devices on page 68 Note WEP security does not support WPS If you try to use WPS to connect a WEP device to your network it will not connect 1 For a list of other Wi Fi certified products available from NETGEAR go to http www wi fi org 36 Chapter3 Wireless Settings N150 Wireless ADSL2 Modem Router DGN1000 User Manual You can use the WPS Push N Connect or router interface method to add wireless devices and other equipment to your wireless network WPS Push N Connect Method If your wireless device supports WPS Push N Connect follow these steps 1 2 3 2 Press the WPS button on the router front panel W
67. has a user login on the RADIUS server and the wireless modem router has a client login on the RADIUS server Data transmissions are encrypted with an automatically generated key For information about how to use the WPA enterprise option see Set WPA 802 1x Server and Passphrase on page 42 Chapter 3 Wireless Settings 35 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Add Clients Devices to Your Network Choose either the manual or the WPS method to add wireless devices including guest devices and other equipment to your wireless network Manual Method 1 Open the software that manages your wireless connections on the wireless device laptop computer gaming device iPhone that you want to connect to your router This software scans for all wireless networks in your area 2 Look for your network and select it If you did not change the name of your network during the setup process look for the default Wi Fi network name SSID and select it The default Wi Fi network name SSID is located on the product label on the bottom of the router 3 Enter the wireless modem router passphrase and click Connect The default wireless modem router passphrase is located on the product label on the bottom of the router 4 Repeat steps 1 3 to add other wireless devices Wi Fi Protected Setup WPS Method Wi Fi Protected Setup WPS is a standard for easily adding computers and other devices to a home network while maintainin
68. he modem receives data from the DSL line at this speed UpStream Connection Speed The modem transmits data to the DSL line at this speed VPI The Virtual Path Identifier setting VCI The Virtual Channel Identifier setting Wireless Port See Wireless Settings Screen on page 38 for a description of these settings Name SSID The Wi Fi network name service set ID for the wireless network Region The country where the unit is set up for use Channel The current channel which determines the operating frequency Wireless AP Indicates if the access point feature is enabled If disabled the Wireless LED on the front panel is off Broadcast Name Indicates if the wireless modem router is configured to broadcast its SSID Chapter 5 Network Maintenance 65 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Show Statistics Button Click the Show Statistics button on the Router Status screen to display a screen similar to this System Up Time 03 52 30 Port Status TxPkts RxPkts Collisions Tx Bis Rx B s Up Time WAN PPPoA 1131 55 D 4 1 03 52 02 LAN 10141 00M 864 1869 o 29 03 52 25 WLAN 11M 54M 270M 411 D 0 7 D 03 52 21 ADSL Link Downstream Upstream Connection Speed 8128 kbps 832 kbps Line Attenuation 0 0 db 1 0 db Noise Margin 19 7 db 6 0 db Poena idl 009 Figure 40 System up time and poll interval statistics Fill in the fields as follows Port The statistics for the WAN Internet LAN local and w
69. ice handles the ISP connection Table 5 Wireless Button and LED Icon LED Activity Description Solid green There is wireless connectivity e Blinking green Data is being transmitted or received over the wireless link Icon is on the off There is no wireless connectivity You can still plug an Ethernet cable into Wireless one of the LAN ports to get wired connectivity See Turn Off Wireless button Connectivity on page 34 for more information about the use of this button Table 6 WPS Button and LED Icon LED Activity Description Solid green Indicates that wireless security has been enabled Blinking green WPS capable device is connecting to the device Icon is on the off WPS is not enabled See Wi Fi Protected Setup WPS Method on page 36 WPS button for more information about the use of this button Chapter 1 Hardware Setup 11 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Position Your Wireless Router The wireless modem router lets you access your network from virtually anywhere within the operating range of your wireless network However the operating distance or range of your wireless connection can vary significantly depending on the physical placement of your router For example the thickness and number of walls the wireless signal passes through can limit the range For best results place your router Near the center of the area where
70. ider using the Dynamic DNS screen described in Dynamic DNS on page 73 so that external users can always find your network Ifthe IP address of the local server computer is assigned by DHCP it might change when the computer is rebooted To avoid this use the Reserved IP address feature in the LAN IP Setup screen to keep the computer s IP address constant e Local computers are required to access the local server using the computer s local LAN address 192 168 0 11 in the example shown in Figure 27 Allow inbound video conferencing Attempts by local computers to access the server using the external WAN IP address fail 50 Chapter 4 Security Settings N150 Wireless ADSL2 Modem Router DGN1000 User Manual Outbound Rules Service Blocking The wireless modem router lets you block computers on your local network from using certain Internet services This is called service blocking or port filtering You can define an outbound rule to block Internet access from a local computer based on local computer Internet site being contacted time of day and type of service being requested 1 Select Security gt Firewall Rules to display the following screen Firewall Rules Outbound Services Outbound Services Enable Service Name Action LAN Users WAN Servers 1 V FINGER BLOCK always Any Any Action BLOCK always Service Any ALL Default Yes Any ALLOW always Any Any LAN Users Add Edit Move Delete
71. ime Zone The wireless modem router uses the Network Time Protocol NTP to obtain the current time and date from one of several network time servers on the Internet You can check and set if needed the time zone to ensure time stamps match your local time 1 Select Security gt Schedule to display the following screen Schedule ays Iv Every Day Sunday Monday Tuesday Wednesday Thursday Friday Saturday Time of day use 24 hour clock v All Day Start Time Hour Minute End Time Hour Minute Time Zone GMT Greenwich Mean Time Edinburgh London Cl Adjust for Daylight Savings Time C Use this NTP Server Current Time 2000 01 01 00 25 26 Apply Cancel Figure 31 Time zone options 2 Select your time zone This setting determines the blocking schedule and time stamping of log entries 3 If your time zone is in daylight savings time select the Adjust for Daylight Savings Time check box to add one hour to standard time Note If your region uses daylight savings time select Adjust for Daylight Savings Time on the first day and clear it after the last day 4 The wireless modem router has a list of NETGEAR NTP servers If you would prefer to use a particular NTP server as the primary server select the Use this NTP Server check box and enter its IP address 5 Click Apply to save your settings 54 Chapter4 Security Settings N150 Wireless ADSL2 Modem Router DGN1000 User Manual
72. ir destination WAN IP address Select the option that you want Any All IP addresses are covered by this rule Address range If this option is selected fill in the Start and Finish fields Chapter 4 Security Settings 51 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Single address Enter the required address in the Start field Log You can select to log the traffic Never No log entries are made for this service Always Any traffic for this service type is logged Match Traffic of this type that matches the settings and action is logged Not match Traffic that does not match the settings and action are logged Configure Services Services are functions performed by server computers at the request of client computers For example Web servers serve Web pages time servers serve time and date information and game hosts serve data about other players moves When a computer on the Internet sends a request for service to a server computer the requested service is identified by a service or port number This number appears as the destination port number in the transmitted IP packets For example a packet that is sent with destination port number 80 is an HTTP Web server request The service numbers for many common protocols are defined by the Internet Engineering Task Force IETF at htto www ietf org and published in RFC1700 Assigned Numbers Service numbers for other applications are typically chosen fr
73. ireless LAN WLAN ports For each port the screen displays the following Status The link status of the port TxPkts The number of packets transmitted since reset or manual clear RxPkts The number of packets received since reset or manual clear Collisions The number of collisions since reset or manual clear Tx B s The current line utilization percentage of current bandwidth used Rx B s The average line utilization Up Time The time elapsed since the last power cycle or reset ADSL Link Downstream or Upstream The statistics for the upstream and downstream DSL link These statistics are of interest to your technical support representative if you have problems obtaining or maintaining a connection Connection Speed Typically the downstream speed is faster than the upstream speed Line Attenuation The line attenuation increases the farther you are physically located from your ISP s facilities Noise Margin The signal to noise ratio which is a measure of the quality of the signal on the line Poll Interval The interval at which the statistics are updated in this window Click the Stop button to freeze the display 66 Chapter 5 Network Maintenance N150 Wireless ADSL2 Modem Router DGN1000 User Manual Connection Status Button In the Router Status screen click the Connection Status button to display a screen similar to this Connection Status Connection Time 05 15 17 Connecting to Server Connected Negoti
74. ithin 2 minutes press the WPS button on your wireless device or follow the WPS instructions that came with the device The device is now connected to your router Repeat steps 1 2 to add other WPS wireless devices Router Interface Method 1 2 Select Add WPS Client at the top of the router menus If you cannot select Add WPS Client select Setup gt Wireless Settings and make sure WPS is selected Click Next The following screen lets you select the method for adding the WPS client Add WPS Client Select a setup method te Push Button recommended You can either press the Push Button physically on the router or press the Button below soft Push Button PIN Number Figure 16 Add WPS Client using the push button method Select either Push Button or PIN Number With either method the client wireless device attempts to detect the WPS signal from the wireless modem router and establish a wireless connection in the time allotted Chapter 3 Wireless Settings 37 N150 Wireless ADSL2 Modem Router DGN1000 User Manual The PIN method displays this screen so you can enter the client security PIN number Add WPS Client Select a setup method 2 Push Button recommended 9 PIN Number If your Adapter supports VPS please click on Generate a client Security Pin to input on the AP Router Gateway and putthe generated client PIN number here Enter Client s PIN Apply Figure 17 Add WPS Client using
75. lect Security gt Schedule to display the current date and time The wireless modem router uses the Network Time Protocol NTP to obtain the current time from one of several network time servers on the Internet Each entry in the log is stamped with the date and time of day Problems with the date and time function can include the following e Date shown is January 1 2000 This means the router has not yet successfully reached a network time server Check that your Internet access is configured correctly If you have just completed configuring the router wait at least 5 minutes and check the date and time again Time is off by one hour The router does not automatically sense daylight savings time In the Schedule screen select the Adjust for Daylight Savings Time check box Chapter 7 Troubleshooting 93 Supplemental Information This appendix includes the factory default settings technical specifications for the N150 Wireless ADSL2 Modem Router DGN1000 related documents and instructions for wall mounting the unit This appendix contains the following sections e Factory Settings e Technical Specifications e Related Documents e Wall Mount Your Router Appendix A Supplemental Information 94 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Factory Settings You can return the wireless modem router to its factory settings On the bottom of the wireless modem router use the end of a paper clip or some other
76. lt the wireless modem router broadcasts its Wi Fi network name SSID so devices can find it If you change this setting to not allow the broadcast wireless devices will not find your wireless modem router unless they are configured with the same SSID See Wireless Access Point Settings on page 40 for the procedure Note Turning off SSID broadcast nullifies the wireless network discovery feature of some products such as Windows XP but the data is still fully exposed to a determined snoop using specialized test equipment like wireless sniffers If you allow the broadcast be sure to keep wireless security enabled Restrict Access by MAC Address You can enhance your network security by allowing access to only specific PCs based on their Media Access Control MAC addresses You can restrict access to only trusted PCs so that unknown PCs cannot wirelessly connect to the wireless modem router MAC address filtering adds additional security protection to the wireless security option you have in force The Wireless Station Access List determines which wireless hardware devices are allowed to connect to the wireless modem router by MAC address See Wireless Station Access List Settings on page 40 for the procedure Wireless Security Options A security option is the type of security protocol applied to your wireless network The security protocol in force encrypts data transmissions and ensures that only trusted devices receive authorization to conn
77. lu n ustanovenia Smernice 1999 5 ES Suomi Finnish NETGEAR Inc vakuuttaa t ten ett Radiolan tyyppinen laite on direktiivin 1999 5 EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen Svenska Swedish H rmed intygar NETGEAR Inc att denna Radiolan st r verensst mmelse med de v sentliga egenskapskrav och vriga relevanta best mmelser som framg r av direktiv 1999 5 EG slenska Icelandic H r me l sir NETGEAR Inc yfir v a Radiolan er samr mi vi grunnkr fur og a rar kr fur sem ger ar eru i tilskipun 1999 5 EC Norsk Norwegian NETGEAR Inc erkl rer herved at utstyret Radiolan er i samsvar med de grunnleggende krav og vrige relevante krav i direktiv 1999 5 EF Interference Reduction Table The table below shows the Recommended Minimum Distance between NETGEAR equipment and household appliances to reduce interference in feet and meters Table 11 Household Appliance Recommended Minimum Distance in feet and meters Microwave ovens 30 feet 9 meters Baby Monitor Analog 20 feet 6 meters Baby Monitor Digital 40 feet 12 meters Cordless phone Analog 20 feet 6 meters Cordless phone Digital 30 feet 9 meters Bluetooth devices 20 feet 6 meters ZigBee 20 feet 6 meters 104 Appendix B Notification of Compliance Index A AC power adapter input 9 access lists 41 adapter wireless 1
78. ly as Required Enable PPPoE Relay Disable Port Scan and DOS Protection v Default DMZ Server Respond to Ping on Internet WAN Port MTU Size in bytes C Disable SIP ALG Cancel Figure 45 Configure a DMZ server 2 Type the IP address for that server 3 Fill in the following fields and click Apply Respond to Ping on Internet WAN Port If you want the wireless modem router to respond to a ping from the Internet select this check box This should be used only as a diagnostic tool because it allows your wireless modem router to be discovered Do not select this check box unless you have a specific reason to do so MTU Size in bytes The normal Maximum Transmit Unit MTU value for most Ethernet networks is 1500 bytes or 1492 bytes for PPPoE connections For some ISPs you might need to reduce the MTU But this is rarely required and should not be done unless you are sure it is necessary for your ISP connection 72 Chapter6 Advanced Settings N150 Wireless ADSL2 Modem Router DGN1000 User Manual Disabling the SIP ALG The Session Initiation Protocol SIP Application Level Gateway ALG is enabled by default to optimize VoIP phone calls that use the SIP The Disable SIP ALG check box allows you to disable the SIP ALG Disabling the SIP ALG might be useful when running certain applications Dynamic DNS If your network has a permanently assigned IP address you can register a domain name and have
79. n 35 wall mount router 99 WPS PSK WPA2 PSK encryption 35 WAN 71 wrong date or time 93 advanced setup 71 automatic connection 71 108 Index
80. odem router to set the country language and Internet connection 1 Note If you performed the NETGEAR Genie setup the country language Internet and wireless network settings are already configured Select Setup Wizard from the top of the router menus to display the following screen Setup Wizard Select Country and Language Country NGA Language English Auto Detect Connection Type This Setup Wizard can detect the type of Internet connection you have Do You want The Smart Setup Wizard To try And detect The connection type now Yes O No want to configure The Router myself Next Figure 12 Country and language settings in Setup Wizard Select your country and language e Country It is important to specify the location where the wireless modem router operates so that the Internet connection works correctly Defaults to UK e Language Defaults to English You can select another language if you prefer Select either Yes or No want to configure the Router myself If you select No proceed to Manual Setup Basic Settings on page 25 If you selected Yes click Next With automatic Internet detection the Setup Wizard searches your Internet connection for servers and protocols to determine your ISP configuration Note The Setup Wizard cannot detect a Point to Point Tunneling Protocol PPTP connection If your ISP uses PPTP you have to set your Internet connection through the screen described in Manu
81. of the steps and verifies that those steps have been successfully completed It takes about 15 minutes to complete Before running the NETGEAR Genie on a corporate PC check with your company s network support staff Corporate network settings or virtual private network VPN client software might conflict with the default settings of a home router If you are unsure about whether there might be a conflict use a different computer 1 Locate the DSL settings information user name and password provided by your ISP Contact your ISP if you do not have it 2 Insert the Resource CD into your Windows PC The CD automatically starts and detects the language you are using on your PC Select a different language option if you prefer Note If the CD does not start go to the CD drive under My Computer on Windows browse the CD and double click ENG Chapter 2 Router Internet Setup 19 N150 Wireless ADSL2 Modem Router DGN1000 User Manual 3 When the Welcome screen displays click Setup to start the Genie Follow the instructions to complete the setup NETGEAR Genie checks your hardware setup and guides you through connecting the router to the Internet and adding computers to your network Your wireless modem router connects to the Internet when any of the computers connected to your network require access When you launch a Web browser to access the Internet the router s Internet LED blinks to indicate ISP communication View
82. om the range 1024 to 65535 by the authors of the application Although the wireless modem router already holds a list of many service port numbers you are not limited to these choices To create your own service definitions 1 Select Security 5 Services to display the following screen Services Service Table E Service Name Ports Add Custom Service Delete Service Figure 29 View the current services e To create a new service click the Add Custom Service button to display the Add Services screen To edit a service select its button on the left side of the table and click Edit Service 52 Chapter4 Security Settings N150 Wireless ADSL2 Modem Router DGN1000 User Manual To delete a service select its button on the left side of the table and click Delete Service 2 Use the following screen to define or edit a service Add Services Service Definition Name Type Start Port Finish Port Apply Cancel Figure 30 Create a new service Name Enter a meaningful name for the service e Type Select the correct type for this service If in doubt select TCP UDP The options are TCP UDP TCP UDP Start Port and End Port If a port range is required enter the range here If a single port is required enter the same value in both fields 3 Click Apply to save your changes Chapter 4 Security Settings 53 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Set the T
83. ommends that you not change your preset security settings If you do decide to change your preset security settings make a note of the new settings and store it in a safe place where you can easily find it Security Basics Unlike wired network data wireless data transmissions extend beyond your walls and can be received by any device with a compatible wireless adapter radio For this reason it is very important to maintain the preset security and understand the other security features available to you Besides the preset security settings described above your wireless modem router has the security features described here and in Chapter 4 Security Settings e Turn off wireless connectivity e Disable SSID broadcast e Restrict access by MAC address e Wireless security options Chapter 3 Wireless Settings 33 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Turn Off Wireless Connectivity You can completely turn off the wireless connectivity of the wireless modem router by pressing the Wireless On Off button on its front panel For example if you use your notebook computer to wirelessly connect to your wireless modem router and you take a business trip you can turn off the wireless portion of the modem router while you are traveling Other members of your household who use computers connected to the wireless modem router through Ethernet cables can still use the wireless modem router Disable SSID Broadcast By defau
84. on one more time to see if the wireless modem router recovers e Clear the router s configuration to factory defaults as explained in Factory Settings on page 95 This sets the routers IP address to 192 168 0 1 If the error persists you could have a hardware problem and should contact NETGEAR Technical Support LAN or DSL Link LED Is Off If either the LAN or DSL link LED does not light when the Ethernet connection is made check the following e The Ethernet cable connections are secure at the router and at the hub or workstation The power is turned on to the connected hub or workstation e You are using the correct cable When connecting the DSL port use the cable that was supplied with the wireless modem router If the DSL link LED is still off this could mean that there is no DSL service or the cable connected to the DSL port is bad See also DSL Link LED Is Off on page 87 86 Chapter 7 Troubleshooting N150 Wireless ADSL2 Modem Router DGN1000 User Manual No Internet Connection If your router cannot access the Internet first check the DSL connection and then check the WAN TCP IP connections See Figure 54 Front panel LED Icons on page 85 for the location of the LEDs DSL Link First determine whether you have a DSL link with the service provider The state of this connection is indicated by the DSL LED DSL Link LED Is Green or Blinking Green You have a good DSL connection The service provider has connect
85. on the left side of the table and click Move b Atthe prompt enter the number of the new position and click OK 5 To open or close instant messaging select a radio button and click Apply Close IM Ports Disables instant messaging traffic e Open IM Ports Enables instant messaging traffic IM ports are open by default 6 Click Apply to save your settings Chapter 4 Security Settings 47 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Inbound Rules Port Forwarding Because the wireless modem router uses Network Address Translation NAT your network presents only one IP address to the Internet and outside users cannot directly address any of your local computers However by defining an inbound rule you can make a local server for example a Web server or game server visible and available to the Internet The rule tells the wireless modem router to direct inbound traffic for a particular service to one local server based on the destination port number This is also known as port forwarding Allowing inbound services opens holes in your firewall Enable only those ports that are necessary for your network The following are two examples of inbound rules Note Some residential broadband ISP accounts do not let you run server processes such as a Web or FTP server from your location Your ISP might periodically check for servers and suspend your account if it discovers any active services at your location If you are
86. onfiguration Protocol DHCP server 76 E email notices 56 encryption keys 35 erasing configuration 63 Index 105 erasing configuration file 63 Ethernet cable 16 F factory default settings restoring 63 factory settings list of 95 resetting 8 filtering content 44 firewalls CU SeeMe connection 49 IM ports 47 inboudn rules 49 inbound rules 48 outbound rules 51 rules 46 firmware automatic check 59 reload firmware message 92 upgrade 59 80 upgrade at log in 22 upgrade manually 61 front panel 10 front panel LEDs 10 G gateway IP address 27 Genie NETGEAR 19 glossary link to 98 guest devices adding 36 H host name 26 host trusted 46 inbound firewall rules 48 installing manual setup 25 NETGEAR Genie 19 Setup Wizard 24 Instant Messaging IM ports 47 Internet port 20 24 Internet port LEDs 11 Internet port no connection 29 Internet Service Provider ISP see ISP IP address DHCP 18 N150 Wireless ADSL2 Modem Router DGN1000 User Manual LAN service 74 reserved 76 IP setup LAN 74 ISP account information 19 Basic Settings screen 26 DSL settings 28 DSL synchronization 11 ISP login 19 K keywords blocking 45 deleting 46 L label product 8 LAN ports 65 setup 75 LAN port LEDs 10 LAN ports 9 LAN setup 74 language setting 24 LEDs troubleshooting 85 verifying cabling 16 logging in cannot 91 changing password 30 ISP 19 router 21 time out 30 types 31 upgrad
87. ontents Chapter 1 Hardware Setup Unpack Your New ROWER ccs a naa Eod d 1b ed ei CR BOE GALE KABI 7 Har ware Fenles ia i ueber ed E e reich debe duda or Dx doe e 8 Ul MITT CDL PREISE TET PER ea 8 Baok Pane xoa edu y obra do bord NU Edda Rol RE ba dI end qaaa dd 9 From PANS uns zedac RF RRCRE ERA RO RAgOMPGG RK P REGE Ed aces 10 Position Your Wireless Router a 12 ADSL Micronit eses Ba ET LARA GL 400 ee oa oa ee oe ARR PRAG 4 13 One Line ADSL Microfilter llle 13 Two Line ADSL Misreflllal 4d dX KAPPA KING LGA PUNA 14 JUNO s IKA KKK ESSE AAA se bd Rueda doch dudes 14 Cable Your N150 Wireless Modem Router 0 000 eee 15 VSR he Cabling srssridirsreirra tetp reno Ad NG eRe eae Kana 16 Chapter 2 Router Internet Setup Router Setup Preparali sar sn KA eed AMANG A eee ee en ee de 18 Use Standard TCP IP Properties for DHCP 18 Replace an Existing ROUIE si namamaga KAKA B eee bd AARON EE in 18 Adapters and Security Settings aaa aaa 18 Gather ISP Information AAP APA 19 NETGEAR GENE Sep c cesoauue Re Trine ENEE RE e re e er vs 19 View or Change Settings 64425 ue a R REARARERIOTARREERS RES 20 Settings DeSCrIploll esses eaaena Reed eRre RR REAESRU EAR ESSA 20 Log In to the N150 Modem Router aa 21 Upgrade Router PINANG siers REA eden ERR RA HER PG PCEEqEAqeNA 22 Router Interface AA 23 SEHE QUE BI pU na dani des CLA MIE ATES OS ER p dr cp REDE dd 24 Manual Setu
88. or Change Settings You can view and change the settings in the following ways e Login to your router by clicking the desktop shortcut N that was placed on your desktop during the NETGEAR Genie setup The shortcut icon is put on your desktop only when you use the NETGEAR Genie setup method e Login to your router See Log In to the N150 Modem Router on page 21 e Open the Router Setup html file that was placed on your desktop during the NETGEAR Genie setup This file provides setup and system information the NETGEAR Technical Support number links to the NETGEAR website and a router login link Settings Description When the NETGEAR Genie setup is completed your router has the following configuration and informational settings Some of these settings can be viewed in Router_Setup html Configuration Wireless settings The preconfigured Wi Fi network name SSID passphrase and security option encryption protocol See Preset Security on page 33 for more information e Internet connection including language and country as described in Setup Wizard on page 24 WAN port settings This is your port address type PPPoE by default and ISP login name and password See Manual Setup Basic Settings on page 25 for more information about address types Login and System Information Router login The router administrator login name and password as described in Log In to the N150 Modem Router on page 21 e System information
89. ost TCP IP terminal devices and routers have a ping utility for sending an echo request packet to the designated device The device responds with an echo reply to tell whether a TCP IP network is responding to requests Chapter 7 Troubleshooting 89 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Test the LAN Path to Your Wireless Modem Router You can ping the router from your computer to verify that the LAN path to your router is set up correctly To ping the router from a PC running Windows 95 or later 1 From the Windows task bar click the Start button and select Run 2 In the field provided type ping followed by the IP address of the router as in this example ping 192 168 0 1 3 Click OK a You should see a message like this one Pinging lt IP address gt with 32 bytes of data b If the path is working you see this message Reply from lt IP address gt bytes 32 time NN ms TTL xxx c If the path is not working you see this message Request timed out If the path is not functioning correctly you could have one of the following problems e Wrong physical connections Make sure that the LAN port LED is on If the LED is off follow the instructions in LAN or DSL Link LED Is Off on page 86 Check that the corresponding link LEDs are on for your network interface card and for the hub ports if any that are connected to your workstation and router e Wrong network configuration Verify that
90. ot required this field displays Use IP Over ATM IPoA Your ISP uses classical IP addresses RFC 1577 Enter the IP address IP subnet mask and gateway IP addresses that your ISP assigned Domain Name Server DNS Address The DNS server is used to look up site addresses based on their names Get Automatically from ISP Your ISP uses DHCP to assign your DNS servers Your ISP automatically assigns this address Use These DNS Servers If you know that your ISP does not automatically transmit DNS addresses to the wireless modem router during login select this option and enter the IP address of your ISP s primary DNS server If a secondary DNS server address is available enter it also NAT Network Address Translation NAT automatically assigns private IP addresses 10 1 1 x to LAN connected devices Enable Usually NAT is enabled Disable This disables NAT but leaves the firewall active Disable NAT only if you are sure you do not need it When NAT is disabled only standard routing is performed by this router Classical routing lets you directly manage the IP addresses that the wireless modem router uses Classical routing should be selected only by experienced users 1 Disabling NAT reboots the wireless modem router and resets its configuration settings to the factory defaults Disable NAT only if you plan to set up the wireless modem router in a setting where you will be manually administering the IP address space on the L
91. p Basic Settings a 25 DSL OMe a ada kanak E E E E E T 28 Unsuccessful Internet Connection 2 6 aaa cee ee eee ees 29 Change Password and Login Time Out 0000 e eae 30 Log Out Manually ccc cscccetcdc taser m RRRRERREA AERE EAE vaca NG 31 Tyee Ol LOGINS eere carder eoedadodGdoodetods en GG GG 31 Chapter 3 Wireless Settings Proset ef M 33 DO B ASIDE ecirar na db pmi edes Ra xe EYE STE 33 Turn Off Wireless Connectivity aaa 34 Contents 3 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Disable SSID Broadcast ossa quus 685454886 0 oR PS oo hoa EE ES 34 Restrict Access by MAC Address 0c eee eeee 34 Wireless Security Options cssc AG e keen eae ane 34 Add Clients Devices to Your Network 22200200 000 36 Manual Method idees mo rx ACER TERRE RE ee EEA HS 36 Wi Fi Protected Setup WPS Method 0 00 020 e eee 36 Wireless Settings Screen a ee eee ee ee ee eee ee ee eee ee NG 38 Consider Every Device on Your Network 0005 39 View or Change Wireless Settings 000 cece eens 39 Change WPA Security Option and Passphrase 42 Set WPA 802 1x Server and Passphrase 42 Set WEP Encryption and Passphrase 20200000 43 Chapter 4 Security Settings Keyword Blocking of HTTP Traffic 2 0 00 eee 45 Delete a Keyword or Domain 000
92. page 98 for information about how to configure your computer Chapter 7 Troubleshooting 91 N150 Wireless ADSL2 Modem Router DGN1000 User Manual If the computer IP address is 169 254 x x recent versions of Windows and Mac OS generate and assign an IP address when the computer cannot reach a DHCP server The auto generated addresses are in the range 169 254 x x If your IP address is in this range check the connection from the computer to the router and reboot your computer e If your routers IP address was changed and you do not know the current IP address clear the router s configuration to factory defaults as explained in Factory Settings on page 95 This sets the router s IP address to 192 168 0 1 e Make sure that your browser has Java JavaScript or ActiveX enabled If you are using Internet Explorer click Refresh to be sure that the Java applet is loaded e Try closing the browser and relaunching it Changes Not Saved If the router does not save the changes you make in the router interface check the following e When entering configuration settings always click the Apply button before moving to another screen or tab or your changes are lost e Click the Refresh or Reload button in the Web browser The changes might have occurred but the old settings might be in the Web browser s cache Firmware Needs to Be Reloaded When you attempt to connect to the Internet the browser might display a message similar to th
93. phrase to access the network e Trusted Wireless Stations lists the trusted computers that have access to your network e Available Wireless Stations lists the currently untrusted computers that are connected to your network Wireless Station Access List Cl Turn Access Control On Trusted Wireless Stations Device Name MAC Address Delete Available Wireless Stations Device Name MAC Address Add Add New Station Manually Device Name MAC Address Add Figure 19 Wireless Station Access List 2 Select the Turn Access Control On check box to enable access restriction by MAC address 3 In the Add New Station Manually list click Add to add your computer s MAC address so you do not lose your wireless connection when you click Apply If you lose your wireless connection you have to access the wireless modem router from a wired computer or from a wireless computer that is on the access control list 4 If a wireless station that you want to add to the Trusted Wireless Stations list is connected to the network select it from the Available Wireless Stations list and click Add 5 Ifthe wireless station is not currently connected you can enter its address manually The MAC address is usually printed on the wireless card or it might appear in the wireless modem router s DHCP table The MAC address is 12 hexadecimal digits You can also copy and paste the MAC addresses from the wireless modem router s Attached Devic
94. primary DNS addresses 27 Push N Connect see WPS R RADIUS server 35 range of wireless connections 12 remote management 79 replace existing router 18 reserved IP address 76 restore configuration file 62 factory settings button 95 restoring default factory settings 63 restricting wireless access by MAC addresses 43 router interface described 23 router menus access from additional port 76 router status 64 router wall mount 99 Router Setup html 20 Routing Information Protocol RIP 74 S secondary DNS 27 security 33 34 see also security options security features 33 security options described 34 settings 34 security PIN 8 38 security settings 44 sending logs by email 56 serial number product label 8 services 51 52 Session Initiation Protocol SIP disabling 73 setting time zone 54 settings viewing 20 Setup Wizard 24 Simple Mail Transfer Protocol SMTP 56 sites blocking 45 SSID described 40 disable 34 Index 107 N150 Wireless ADSL2 Modem Router DGN1000 User Manual SSID product label 8 ping response 72 static routes 80 81 settings 71 72 statistics viewing 66 WAN port status default 20 Internet connection 67 scanning 71 router 64 Wi Fi Protected Setup WPS 36 37 adding devices 36 keep existing settings 78 T settings 77 TCP IP Wi Fi certified products 36 network troubleshooting 89 Wired Equivalent Privacy WEP encryption 43 no Internet connection 29 passphras
95. r t Radiolan in bereinstimmung mit den grundlegenden Anforderungen und den brigen einschl gigen Bestimmungen der Richtlinie 1999 5 EG befindet Eesti Estonian K esolevaga kinnitab NETGEAR Inc seadme Radiolan vastavust direktiivi 1999 5 EU pohinduetele ja nimetatud direktiivist tulenevatele teistele asjakohastele s tetele English Hereby NETGEAR Inc declares that this Radiolan is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC Espa ol Spanish Por medio de la presente NETGEAR Inc declara que el Radiolan cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999 5 CE EAAnvikr Greek ME THN MAPOYZA NETGEAR Inc AHAQNE OTI Radiolan 2YMMOP ONETAI MPO TI OYZIOAEI ANAITHZEIZ KAI TIZ AOITIEZ ZXETIKE2Z AIATAZEIZ TH OAHMIAZ 1999 5 EK Frangais French Par la pr sente NETGEAR Inc d clare que l appareil Radiolan est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999 5 CE Italiano Italian Con la presente NETGEAR Inc dichiara che questo Radiolan conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999 5 CE Latviski Latvian Ar So NETGEAR Inc deklare ka Radiolan atbilst Direktivas 1999 5 EK b tiskajam prasibam un citiem ar to saistitajiem noteikumiem Lietuviu Lithuanian
96. r Manual Back Panel The back panel has the On Off button and port connections as shown in the figure Figure 3 Back panel port connections Viewed from left to right the rear panel contains the following elements 1 RJ 11 Asynchronous DSL ADSL port for connecting the wireless modem router to a DSL line Note An ADSL port is capable of sending data over a DSL line at one speed and receiving it at another speed 2 Four Ethernet RJ 45 LAN ports for cabling the wireless modem router to the local computers 3 Power On Off button 4 AC power adapter input Chapter 1 Hardware Setup 9 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Front Panel The wireless modem router front panel has the nine status LEDs and icons shown in the figure Note that the Wireless and WPS icons are buttons Wireless on off button WPS On Off button Power LAN ports DSL Internet Wireless Figure 4 Front panel LED Icons The tables below describe the LEDs icons and buttons on the front panel from left to right Table 1 Power On Off button Icon LED Activity Description Solid green Power is supplied to the router O Solid red POST power on self test failure or a device malfunction has occurred Off Power is not supplied to the router Restore factory Light blinks momentarily when the Restore Factory Settings button on the settings bottom of the unit is pressed for 6 seconds The Power LED then blinks red
97. re covered by this rule Address range When this option is selected the Start and Finish fields are required Single address Enter the required address in the Start field Log You can select whether to log the traffic Never No log entries are made for this service Always Any traffic for this service type is logged Match Traffic of this type that matches the settings and action are logged Not match Traffic of this type that does not match the settings and action are logged Inbound Rule Example Allowing Video Conferencing Create an inbound rule to allow incoming video conferencing to be initiated from a restricted range of outside IP addresses such as from a branch office In the following figure CU SeeMe connections are allowed from a specified range of external IP addresses only In this case logging of any incoming CU SeeMe requests that do not match the allowed settings is always allowed Chapter 4 Security Settings 49 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Inbound Services Service CU SEEME TCP UDP 7648 24032 Action ALLOW always v Send to LAN Server WAN Users Address Range start i134 177 88 1 finish 134 177 00 254 NotMatch Capiz Cancer Figure 27 Allow inbound video conferencing Considerations for Inbound Rules e If your external IP address is assigned dynamically by your ISP the IP address might change periodically as the DHCP lease expires Cons
98. reen to manually check the NETGEAR website for newer versions of firmware for your product A WARNING When uploading firmware to the wireless modem router do not interrupt the Web browser by closing the window clicking a link or loading a new page If the browser is interrupted it could corrupt the firmware 1 Select Maintenance 5 Router Status and make a note of the wireless modem router firmware version number Router Status Hardware Version WNDR3700 x x Firmware Version Vi0458 gg Firmware Version GUI Language Version V1 0 0 42 Figure 36 Check the Firmware Version and make a note of it 2 Go to the DGN1000 support page on the NETGEAR website at http www netgear com support 3 If the firmware version on the NETGEAR website is newer than the firmware on your wireless modem router download the file to your computer 4 To upload the newer firmware select Maintenance gt Router Upgrade to display the following screen Router Upgrade Check for New Version from the Internet v Check for New Version Upon Log in Locate and Select the Upgrade File from your Hard Disk Click Browse Figure 37 Upgrade the router firmware manually 5 Click Browse and locate the firmware you downloaded the file ends in img 6 Click Upload to send the firmware to the wireless modem router When the upload completes your wireless modem router restarts The upgrade process typically takes about one minute Read
99. router settings for administering and maintaining the router and home network This chapter contains the following sections Upgrade the Router Firmware e Manually Check for Firmware Upgrades Manage the Configuration File e View Router Status View Attached Devices e Run Diagnostic Utilities Chapter 5 Network Maintenance 58 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Upgrade the Router Firmware The wireless modem router firmware routing software is stored in flash memory By default when you log in to your wireless modem router it checks the NETGEAR website for new firmware and alerts you if there is a newer version A WARNING When uploading firmware to the wireless modem router do not interrupt the Web browser by closing the window clicking a link or loading a new page If the browser is interrupted it could corrupt the firmware Turn Off Automatic Firmwar Checking You can turn the automatic firmware checking off and check for firmware updates manually if you prefer See Manually Check for Firmware Upgrades on page 61 To turn off the automatic firmware check at log in 1 Select Maintenance 5 Router Upgrade 2 Uncheck the Check for Updated Firmware Upon Log in check box at the bottom of this screen Checking for Firmware Updates The router is checking the NETGEAR server to see if upda available for your router This could take up to 90 seconds please wait Check for Updated
100. s This protection should be disabled only in special circumstances Default DMZ Server The default demilitarized zone DMZ server feature is helpful when you use online games and video conferencing applications that are incompatible with NAT The wireless modem router is programmed to recognize some of these applications and to work correctly with them but there are other applications that might not function well In some Chapter 6 Advanced Settings 71 N150 Wireless ADSL2 Modem Router DGN1000 User Manual cases one local computer can run the application correctly if that computer s IP address is entered as the default DMZ server Note For security reasons you should avoid using the default DMZ server feature When a computer is designated as the default DMZ server it loses much of the protection of the firewall and is exposed to many exploits from the Internet If compromised the computer can be used to attack your network Incoming traffic from the Internet is usually discarded by the wireless modem router unless the traffic is a response to one of your local computers or a service that you have configured in the Ports screen Instead of discarding this traffic you can have it forwarded to one computer on your network This computer is called the default DMZ server To assign a computer or server to be a default DMZ server 1 In the WAN screen select the Default DMZ Server check box WAN Setup v Connect Automatical
101. s available click No to exit You can check for new firmware later 3 If new firmware is available click Yes to upgrade the router with the latest firmware After the upgrade the router restarts AN CAUTION Do not try to go online turn off the router shut down the computer or do anything else to the router until the router finishes restarting and the Ready light has stopped blinking for several seconds You cannot upgrade firmware until you have established your Internet connection as described in Setup Wizard on page 24 22 Chapter 2 Router Internet Setup N150 Wireless ADSL2 Modem Router DGN1000 User Manual Router Interface The router interface gives you access to the router s current settings so you can view or change them if needed The left column has the router menus and the right column provides online help The middle column is the screen for the current menu option SMARTWIZARD settings Wireless N 150 ADSL2 Modem Router mode DGN1000 Router Menus Online help Setup Wizard Router Upgrade scroll to see yn i more irat p for the current Check for New Version from the Internet screen Basic Settings ADSL Settings Check for New Version Upon Log in Wireless Settings p Locate and Select the Upgrade File from your Hard Disk Logs B Browse Block Sites Firewall Rules Services Schedule urrent screen E mail Router Status Attached Devices Backup Settings Set Passwor
102. s not match the rule and change the order of rule precedence See Configure Services on page 52 for information about services All traffic attempting to pass through the firewall is subjected to the rules in the order shown in the Rules table from the top highest precedence to the default rules at the bottom In some cases the order of precedence is important to determine which communications are allowed into or out of the network 46 Chapter4 Security Settings N150 Wireless ADSL2 Modem Router DGN1000 User Manual 1 Select Security gt Firewall Rules to display the following screen Firewall Rules Outbound Services x Enable Service Name Action LAN Users WAN Servers Log 1 FINGER BLOCK always Any Any Never Default Yes Any ALLOW always Any Any Never Add Edit Move Delete Enable Service Name Action LAN Server IP address WAN Users Log Default Yes Any BLOCK Always Any Any Never Add Edit Move Delete Inbound Services Instant Messaging IM Ports O Close IM Ports Open IM Ports IM ports are open by default Apply Cancel Figure 25 Configure custom rules for outbound and inbound services 2 To add an inbound or outbound rule Foran outbound rule click Add under Outbound Services e Foran inbound rule click Add under Inbound Services 3 To edit or delete a rule select its button on the left side and click Edit or Delete 4 To change the order of precedence a Select its button
103. see Troubleshooting on page 84 Chapter 2 Router Internet Setup 25 N150 Wireless ADSL2 Modem Router DGN1000 User Manual ISP does not require login Basic Settings Does Your Interp t Connection Require A Login O Yes No Account Name If Required Domain Name if Required Internet IP Address Get Dynamically From ISP O Use Static IP Address IP Address IP Subnet Mask Gateway IP Address O Use IP Over ATM IPoA IP Address IP Subnet Mask Gateway IP Address Domain Name Server DNS Address Get Automatically From ISP O Use These DNS Servers Primary DNS Secondary DNS NAT Network Address Translation 9 Enable O Disable O Disable firewall Router MAC Address 9 Use Default Address O Use Computer MAC Address O Use This MAC Address Apply Cancel Test ISP does require login Encapsulation Login Password Idle Timeout In Minutes Internet IP Address 9 Get Dynamically From ISP O Use Static IP Address IP Address Domain Name Server DNS Address 9 Get Automatically From ISP Use These DNS Servers Primary DNS Secondary DNS NAT Network Address Translation Enable O Disable O Disable firewall Figure 13 Basic Settings screen without left and with right login The following descriptions explain all of the possible fields in the Basic Settings screen Note that which fields appear in this screen depends on whether or not an ISP login is required Does Your ISP
104. shows a two line ADSL microfilter with built in splitter The phone plugs into the Phone jack as shown Figure 7 ADSL microfilter between phone line and phone 2 Use the included phone cable with RJ 11 jacks to connect the ADSL port A of the wireless modem router to the ADSL port B of the two line ADSL microfilter Figure 8 Cable the modem router to the microfilter CAUTION Incorrectly connecting a filter to your wireless modem router blocks your DSL connection Chapter 1 Hardware Setup 15 N150 Wireless ADSL2 Modem Router DGN1000 User Manual 3 Connect the Ethernet cable C from a wireless modem router LAN port to the Ethernet adapter D in your computer Figure 9 Connect the Ethernet cable to your computer Plug the power adapter into the AC power adapter input labeled Power and plug the other end into a power outlet Connect any additional wired PCs to your router by inserting an Ethernet cable from a PC into one of the three remaining LAN ports Verify the Cabling Verify that your router is cabled correctly by checking the wireless modem router LEDs Turn on the wireless router by pressing the On Off button on the back T Xx amp The Power LED is green when the modem router is turned on The LAN ports are green for each PC cabled to the router by an Ethernet cable The wireless LED is green when the modem router is turned on The DSL LED is green when you
105. t on a circuit different from that which the radio receiver is connected Consult the dealer or an experienced radio TV technician for help Appendix B Notification of Compliance 101 N150 Wireless ADSL2 Modem Router DGN1000 User Manual FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation For product available in the USA market only channel 1 11 can be operated Selection of other channels is not possible This device and its antenna s must not be co located or operation in conjunction with any other antenna or transmitter FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body This transmitter must not be co located or operating in conjunction with any other antenna or transmitter The availability of some specific channels and or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destin
106. ter DGN1000 User Manual Run Diagnostic Utilities The wireless modem router has a diagnostics feature that you can use to perform the following functions e Ping an IP address to test connectivity to see if you can reach a remote host Perform a DNS lookup to test if an Internet name resolves to an IP address to verify that the DNS server configuration is working e Display the Routing table to identify what other wireless modem routers the wireless modem router is communicating with Reboot the wireless modem router to enable new network configurations to take effect or to clear problems with the wireless modem router s network connection Select Maintenance gt Diagnostics to display the following screen Diagnostics Ping an IP address IP Address Perform a DNS Lookup Internet Name IP address DNS Server 206 13 28 12 206 13 29 12 Display the Routing Table Reboot the Router Figure 43 Perform diagnotic testing Chapter 5 Network Maintenance 69 Advanced Settings Configuring for unique situations This chapter describes the advanced features of your wireless modem router The information is for users with a solid understanding of networking concepts who want to set the router up for unique situations such as when remote access from the Internet by IP or domain name is needed This chapter contains the following sections e WAN Setup e Dynamic DNS e LAN Setup e Advanced Wireless Settings
107. the Ethernet card driver software and TCP IP software are both installed and configured on your PC or workstation Verify that the IP address for your router and your workstation are correct and that the addresses are on the same subnet 90 Chapter 7 Troubleshooting N150 Wireless ADSL2 Modem Router DGN1000 User Manual Test the Path from Your Computer to a Remote Device After you verify that the LAN path works correctly test the path from your PC to a remote device In the Windows Run screen type ping n 10 IP address where IP address is the IP address of a remote device such as your ISP s DNS server If the path is functioning correctly replies as described in Test the LAN Path to Your Wireless Modem Router on page 90 display If you do not receive replies Check that your PC has the IP address of your router listed as the default wireless modem router If the IP configuration of your PC is assigned by DHCP this information is not visible in your PC s Network Control Panel Verify that the IP address of the router is listed as the default wireless modem router as described in the online document that you can access by clicking Preparing Your Network on page 98 Check that the network address of your PC the portion of the IP address specified by the netmask is different from the network address of the remote device Check that your cable or DSL modem is connected and functioning If your ISP assigned a host name to
108. the new firmware release notes to determine whether or not you need to reconfigure the wireless modem router after upgrading Chapter 5 Network Maintenance 61 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Manage the Configuration File The router configuration settings are stored in a configuration file cfg This file can be backed up to your computer restored or reverted to factory default settings Back Up 1 Select Maintenance gt Backup Settings to display the following screen Backup Settings Save a Copy of Current Settings Restore Saved Settings from a File Browse Revert to Factory Default Settings Erase Figure 38 Back up your configuration settings 2 Click Backup to save a copy of the current settings 3 Choose a location to store the cfg file that is on a computer on your network Restore 1 Enter the full path to the file on your network or click the Browse button to find the file 2 When you have located the cfg file click the Restore button to upload the file to the wireless modem router Upon completion the wireless modem router reboots A WARNING Do not interrupt the reboot process 62 Chapter 5 Network Maintenance N150 Wireless ADSL2 Modem Router DGN1000 User Manual Erase Under some circumstances for example if you move the router to a different network or if you have forgotten the password you might want to erase the configuration and restor
109. the router is to get a separate splitter To use a one line filter with a separate splitter insert the splitter into the phone outlet connect the one line filter to the splitter and connect the phone to the filter Chapter 1 Hardware Setup 13 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Two Line ADSL Microfilter Use an ADSL microfilter with a built in splitter when there is a single wall outlet that provides connectivity for both the wireless modem router and your telephone equipment Plug the ADSL microfilter into the wall outlet plug your phone equipment into the jack labeled Phone and plug the wireless modem router into the jack labeled ADSL Plugs into the DSL line Figure 6 Two line ADSL microfilter with built in splitter Summary e One line ADSL microfilter Use with a phone or fax machine e Splitter Use with a one line ADSL microfilter to share an outlet with a phone and the wireless modem router Two line ADSL microfilter with built in splitter Use to share an outlet with a phone and the wireless modem router 14 Chapter 1 Hardware Setup N150 Wireless ADSL2 Modem Router DGN1000 User Manual Cable Your N150 Wireless Modem Router The installation guide that came in the box has a cabling diagram on the first page This section walks you through the cabling procedure with detailed illustrations 1 Put an ADSL microfilter between the phone line and the phone as shown here The illustration
110. thod or VPI VCI number enter the setting 1 Select Setup gt ADSL Settings to display the following screen ADSL Settings Multiplexing Method VC BASED 4 VPI VCI 38 DSL Mode Auto Multi mode Figure 14 Enter the multiplexing or VPI VCI setting 2 In the Multiplexing Method drop down list select LLC based or VC based 28 Chapter2 Router Internet Setup N150 Wireless ADSL2 Modem Router DGN1000 User Manual 3 For the VPI type a number between 0 and 255 The default is 8 for the U S version 0 for the world wide version and 1 for the German version 4 For the VCI type a number between 32 and 65535 The default is 35 for the U S version 38 for the worldwide version and 32 for the German version 5 Click Apply Unsuccessful Internet Connection 1 Review your settings to be sure you have selected the correct options and typed everything correctly 2 Contact your ISP to verify that you have the correct configuration information 3 Read Chapter 7 Troubleshooting If problems persist register your NETGEAR product and contact NETGEAR Technical Support Note If you cannot connect to the wireless router check the Internet Protocol TCP IP properties in the Network Connections section of your PC Control Panel They should be set to obtain both IP and DNS server addresses automatically See your computer documentation or follow the links in Related Documents on page 98 for assistance Chapter 2 Ro
111. top one facing up and the bottom one facing away from the router Figure 59 Position the antennas 100 Appendix A Supplemental Information Notification of Compliance NETGEAR Wireless Routers Gateways APs Regulatory Compliance Information This section includes user requirements for operating this product in accordance with National laws for usage of radio spectrum and operation of radio devices Failure of the end user to comply with the applicable requirements may result in unlawful operation and adverse action against the end user by the applicable National regulatory authority Note This product s firmware limits operation to only the channels allowed in a particular Region or Country Therefore all options described in this user s guide may not be available in your version of the product FCC Requirements for Operation in the United States FCC Information to User This product does not contain any user serviceable components and is to be used with approved antennas only Any product changes or modifications will invalidate all applicable regulatory certifications and approvals FCC Guidelines for Human Exposure This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body This transmitter must not be co located or operating in conjunction with any other antenn
112. uffixes such as edu or gov e Enter a period to block all Internet browsing access Chapter 4 Security Settings 45 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Delete a Keyword or Domain 1 Select the keyword you want to delete from the list 2 Click Delete Keyword and click Apply to save your changes Specify a Trusted Computer You can exempt one trusted computer from blocking and logging That computer has to be configured to use a a fixed IP address 1 In the Trusted IP Address field enter the IP address 2 Click Apply to save your changes Firewall Rules to Control Network Access Your wireless modem router has a firewall that blocks unauthorized access to your wireless network and permits authorized inbound and outbound communications Authorized communications are established according to inbound and outbound rules The firewall has the following two default rules You can create custom rules to further restrict the outbound communications or more widely open the inbound communications Inbound Block all access from outside except responses to requests from the LAN side Outbound Allow all access from the LAN side to the outside Configure Firewall Rules The Firewall Rules screen lets you configure custom rules to make exceptions to the default rules Exceptions can be based on the service or application source or destination IP addresses and time of day You can log traffic that matches or doe
113. unsure refer to the acceptable use policy of your ISP Inbound Rule Example A Local Public Web Server If you host a public Web server on your local network you can define a rule to allow inbound Web HTTP requests from any outside IP address to the IP address of your Web server at any time of day as shown here and described in the following figure Inbound Services Service HTTP TCP 80 Action ALLOW always 192 168 0 Send to LAN Server F VYAN Users Any start finish Apply Cancel Figure 26 Allow inbound Web requests 48 Chapter4 Security Settings N150 Wireless ADSL2 Modem Router DGN1000 User Manual Service From this list select the application or service you want to allow or block The list already displays many common services but you are not limited to these choices Use the Services screen to add any additional services or applications that do not already appear See Configure Services on page 52 Action Choose how you want to handle this type of traffic You can block or allow always or you can block or allow according to the schedule you have defined in the Schedule screen described in Schedule Firewall Services on page 55 Send to LAN Server Enter the IP address of the computer or server on your LAN that receives the inbound traffic covered by this rule WAN Users These settings determine which packets are covered by the rule based on their source WAN IP address Any All IP addresses a
114. uter Internet Setup 29 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Change Password and Login Time Out For security reasons the wireless modem router has its own user name and password that default to admin and password You can and should change these to a secure user name and password that are easy to remember The ideal password contains no dictionary words from any language and is a mixture of upper case and lower case letters numbers and symbols It can be up to 30 characters Note The router user name and password are not the same as the user name and password for logging in to your Internet connection See Types of Logins on page 31 for more information about login types 1 Select Maintenance gt Set Password to display the following screen Set Password Old Password New Password Repeat New Password Administrator login times out after idle for 5 minutes Figure 15 Set router login password 2 Enter the old password 3 Enter the new password twice 4 Change the login time out to a value between 1 and 99 minutes if the default value of 5 minutes does not meet your needs The administrator s login to the wireless modem router configuration times out after a period of inactivity to prevent someone else from accessing the router interface when you step away 5 Click Apply to save your changes After changing the password you are required to log in again to continue the configuration If you have
115. utes check that the service name user name and password you are using are correct Also check with your ISP to be sure that there is no problem with their service Note Unless you connect manually the wireless modem router does not authenticate with PPPoE or PPPoA until data is transmitted to the network Cannot Load an Internet Web Page If your wireless modem router can obtain an IP address but your browser cannot load any Internet Web pages Your computer might not recognize any DNS server addresses A DNS server is a host on the Internet that translates Internet names such as www addresses to numeric IP addresses Typically your ISP provides the addresses of one or two DNS servers for your use If you entered a DNS address during the wireless modem router s configuration reboot your computer and verify the DNS address as described in the online document that you can access by clicking Preparing Your Network on page 98 Alternately you can configure your computer manually with DNS addresses as explained in your operating system documentation Your computer might not have the wireless modem router configured as its TCP IP wireless modem router If your computer obtains its information from the wireless modem router by DHCP reboot the computer and verify the wireless modem router address as described in the online document that you can access by clicking Preparing Your Network on page 98 TCP IP Network Not Responding M
116. work settings Security features to prevent objectionable content from reaching your PCs are covered in Chapter 4 Security Settings This chapter contains the following sections e Preset Security e Security Basics Add Clients Devices to Your Network e Wireless Settings Screen Chapter 3 Wireless Settings 32 N150 Wireless ADSL2 Modem Router DGN1000 User Manual Preset Security The N150 Modem Router comes with preset security This means that the Wi Fi network name SSID passphrase and security option encryption protocol are preset in the factory You can find the preset SSID and passphrase on the bottom of the unit Wi Fi network name SSID identifies your network so devices can find it e Passphrase controls access to your network Devices that know the SSID and the passphrase can find your wireless network and connect Note The preset SSID and passphrase are uniquely generated for every device to protect and maximize your wireless security e Security option is the type of security protocol applied to your wireless network The security protocol in force encrypts data transmissions and ensures that only trusted devices receive authorization to connect to your network The preset security option is WPA PSK WPA2 PSK mixed mode described in Wireless Security Options on page 34 The Wireless Settings screen lets you view and change the preset security settings However it is important to understand that NETGEAR rec
117. y email provide your email information in the E mail screen and specify which alerts you want to receive and how often Select Security gt E mail to display the following screen C Turn E mail Notification On Send Alerts and Logs Via E mail Send To This E mail Address Outgoing Mail Server C My Mail Server requires authentication User Name Password Send E Mail alerts immediately v If a DoS attack is detected v If a Port Scan is detected If someone attempts to access a blocked site Send Logs According to this Schedule Hourly M Day Time a m p m Cancel Figure 33 Enable email notifications Fill in the fields as follows Turn E mail Notification On Select this check box if you want to receive email logs and alerts from the wireless modem router Send To This E mail Address Enter the email address where you want logs and alerts sent This email address is also used as the From address If you leave this field blank log and alert messages are not sent by email Outgoing Mail Server Enter the name or IP address of your ISP s outgoing SMTP mail server such as mail mylSP com You might be able to find this information in the configuration settings of your email program Enter the email address to which logs and alerts are sent This email address is also used as the From address If you leave this field blank log and alert messages are not sent by e mail My Mail Server requires authentication I
118. your computers and other devices operate and preferably within line of sight to your wireless devices So it is accessible to an AC power outlet and near Ethernet cables for wired computers In an elevated location such as a high shelf keeping the number of walls and ceilings between the wireless modem router and your other devices to a minimum Away from electrical devices that are potential sources of interference such as ceiling fans home security systems microwaves PCs or the base of a cordless phone or 2 4 GHz cordless phone Away from any large metal surfaces such as a solid metal door or aluminum studs Large expanses of other materials such as glass insulated walls fish tanks mirrors brick and concrete can also affect your wireless signal With the antenna in a vertical position to provide the best side to side coverage or with the antenna in a horizontal position to provide the best up and down coverage as applicable Also be aware that when you use multiple access points it is better if adjacent access points use different radio frequency channels to reduce interference The recommended channel spacing between adjacent access points is 5 channels for example use Channels 1 and 6 or 6 and 11 12 Chapter 1 Hardware Setup N150 Wireless ADSL2 Modem Router DGN1000 User Manual ADSL Microfilters If this is the first time you have cabled a wireless router between a DSL phone line and your computer or laptop

N150 Wireless ADSL2+ Modem Router DGN1000 User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents