Diamond 8 Plus - HME Mobility & Accessibility
Contents
1. level of protection from solid objects up to 12 mm e g person s fingers Second number 1 describes the level of protection from liquids Protection against vertically falling drops of water e g condensation Mattress Features Woven Polyester fabric w PVC backing User Manual Diamond 8 Plus ahead of the curve Symbols Used Refer to Accompanying Documents Type BF Applied Part 1 Instructions for Proper Use i Remove the existing mattress from the bed frame li Replace the standard mattress with mattress replacement system orient mattress so that the air tube 1s at the foot of the bed iu Secure straps beneath the mattress to the bed frame iv Hang the control unit on the foot board of the bed frame v Attach the air tube connectors to the socket on the left panel of the control unit vi Verify that air hoses are not kinked under the mattress vil Attach cover to mattress vill Plug in the control unit and turn on the master power switch on the right side panel the STANDBY LED will illuminate ix Push the STANDBY OPERATE button on the front panel OPERATE LED will now be illuminated and the control unit will be in operation User Manual Diamond 8 Plus ahead of the curve x Pressing MAX button will activate quick inflation to bring the mattress to a flat surface for performing nursing tasks with maximum pressure The pump is set to default back to ALTER after 30 minutes of inf2. responsible and recycle this product through your recycling facility at its end of life User Manual Diamond 8 Plus ahead of the curve 5 Maintenance and Troubleshooting No daily maintenance is required This equipment should only be serviced by authorized technical personnel Use only original spare parts and consumables In case of minor problems refer to the following Symptom Inspection Procedure Possible Solution The air is flowing out from the control unit but the mattress is not inflating The Control Unit is not working Some air cells have abnormal low air pressure while the air pressure for other air cells is normal 6 Warranty Do the air tubes allow smooth airflow Is an air tube kinked Is there any air leakage from the air cells Is there any air leakage from air tube between mattress and control unit Has the air tube connector been connected properly Check the fuse Is the connection between air cells and the manifold kinked Is there any air leakage from the air cells Adjust the air tubes to enable smooth air flow Replace with new air cells Replace with new air tubes Re connect the air tubes Replace with a new fuse Fuses may only be exchanged by qualified and authorized personnel Adjust the connection between cells and manifold Replace with a new air cell Quart Healthcare Products guarantees that this equipment is free from defects in materials and workmanship Our o
3. User Manual Diamond 8 Plus ahead of the curve Diamond 8 Plus Alternating Micro Low Air Loss Pressure Relief System User Manual Distributed by Quart Healthcare Inc www quarthealthcare com User Manual Diamond 8 Plus RS o 9 9 9 9 9 9 o 9 9 e 9 o 9 9 9 ahead of the curve Warning Connect the Master Control unit to a proper power source Do not use the system in the presence of any flammable gases such as Anesthetic Agents Keep the pump and mattress away from sources of liquid and open flames Keep mattress away from sharp objects The device is not AP APG protected Keep mattress system away from heating devices Caution Consult clinical instructor before use of mattress Support surfaces should always be used in conjunction with a care plan that includes the turning repositioning of the patient over a 24 hour period The control unit should only be repaired by an authorized distributor Do not drop the control unit or store it in direct sunlight or extreme cold conditions Operation Temp 5 C 40 C R H 15 93 During operation cell phone with a maximum output power of 2W shall be kept at least of 3 3 m The plug is used as the disconnection device from the AC mains The plug shall be located for easily accessib
4. and Replace a new Filter 2 Use a soft bristle brush to remove dust and difficult dried on soil Do not use phenol based cleaning solutions Switch off the electrical supply to the pump and disconnect the power cord from the main supply before cleaning and inspection User Manual Diamond 8 Plus ahead of the curve 3 Storage and Care Control Unit Check the power cord and plug for abrasions and excessive wear Plug in the unit and verify air flow from the hose connection ports Place in plastic bag for storage Mattress Replacement System Check the air manifold for kinks or breaks Replace if necessary Twist open the CPR plug at the head of the mattress and disconnect the air feed tubes All of the air will be expelled Starting at the head of the mattress roll towards the foot of the bed Use the base mounted straps to secure Place the system in a plastic bag for storage It is recommended that the following guidelines are used whenever the system is being stored or transported to another location Temperature limitations 2560 C LIC 70 C Relative humidity 30 93 4 Waste Disposal This Product has been supplied from an environmentally aware manufacturer that complies with the WEEE This product may contain substances that could be harmful to the environment if disposed of in places landfills that are not appropriate according the legislation Please be environmentally
5. bligation under this warranty is limited to the repair of equipment returned to the place of purchase within 24 months of delivery date We agree to service adjust any equipment returned and to replace or repair any part that is proven to be a warranty defect at no charge This warranty excludes equipment damage through shipping tampering improper maintenance carelessness accident negligence or misuse or products that have been altered repaired or dismantled other than with the manufacture s written authorization and by its approved procedures and by properly qualified technicians In no event shall Quart Healthcare Products be liable for any direct indirect or consequential damages or losses resulting from the use of equipment
6. es of enclosed convoluted foam to provide extra protection and comfort for the patient in case of power failure and the mattress deflates Control Unit Features pump 9 oe 5 digital pressure setting for individual preference The pump is set to default to Alter n Alternation mode for daily operation Press a to select Static mode if required In addition the caregiver can select the Static Function stopping the alternating function and providing only micro low air loss therapy The auto firm function provides uniform firmness for nursing procedures Power failures produce an audio alarm for added safety The alarm can be disabled by pushing the ALARM RESET Button on the front panel Double insulation provides near silent operation The foot board mounting rack provides convenient placement for the control unit on the bed Individual air cushion design for maximum pressure distribution Centre air cells are vented to provide micro low air loss therapy User Manual Diamond 8 Plus ahead of the curve Master Control Unit Model No Part No Size cm 34 5 L x12 5 W x22 5 H Weight Kg Cycle Time min 20 min Max Flow rate Rated Voltage Rated Frequency Current Classification UL60601 1 Class Il Type BF Not AP or AGP Type Meet IP21 standard Classification to Health Canada IP classification P21 First number 2 describes the
7. lation After the mattress is fully inflated the caregiver can transfer the patient to the mattress xi Push MAX again to release the fast inflation mode O Battery status status Orange light will be illuminated if low battery Green light will be flashing when battery is in recharge O L Low Pressure Pressure Possible air leaks or loose tubing connection result in low pressure Lock Function Press the LOCK button for 3 seconds to unlock the face plate Static Function Push the STATIC button and adjust the comfort control by pressing the SOFT FIRM button to achieve maximum patient comfort On this mode the system provides only low air loss therapy Perform a hand check by placing hand under the patient s buttocks between the cells and foam The patient should have at least 4 cm of clearance between the buttocks and the bottom of the mattress Dynamic Function Push the alternate button to enable the 3 1 alternating function CPR Deflation For quick mattress deflation disconnect the hose connector from the controller and release the CPR quick deflation valve User Manual Diamond 8 Plus ahead of the curve O O O Diamond 8 Plus Sayi Bao Failure 1 2 3 4 5 2 Cleaning Mattress Overlay The mattress should be cleaned on the bed weekly using a damp soft cloth and mild detergent If top sheet Top cover or base Bottom cover becomes grossly soiled put on clean gloves plastic gown and eye pro
8. le No modification of this equipment is allowed Contraindications The system should not be applied to patients suffering from polytrauma with fractures of spine pelvis extremities and skull Patients with neurological impairments and missing body perception needs their physician s prescription Alternating pressure should not be applied to pain or pain sensitive patients In these cases we recommend the application of static mode or other suitable foam overlays or other materials which can be found Quart Healthcare product range People who suffer from allergies against any of the substances used for mattress or cells body should not be positioned on the mattress User Manual Diamond 8 Plus ahead of the curve Intended Use The Diamond 8 Plus system is a unique and innovative specialized mattress replacement unit It features a patented 8 shape twin cell design whereby the bottom half of the cell is always inflated and the top half is free to alternate The system utilizes micro low air loss technology with a low rate of flow The advanced 3 1 alternating function also provides active prevention for pressure relief especially for those in acute care and long term care settings the cells inflate and deflate in a 3 1 cycle meaning 2 3rds of the body is always supported at any one time The soft firm adjustment allows the patient to adjust the firmness or softness of the surface for optimal comfort The surface also has 2 inch
9. tection before removing top sheet or base and disposing according to standard hospital procedures for contaminated waste Replace with clean covers Covers can be washed and thermally disinfected in a washing machine following below procedure Never use phenol based cleaning solutions Industrial Break washes Cold 10 minutes Main washes 60 C 6 minutes Main washes 70 C 10 minutes Extraction 2 minutes 3 Cold Rinses Extraction 5 minutes Domestic Pre wash Cold Main Wash 70 C 10 minutes Extraction 2 minutes Cold Rinses Extraction 5 minutes TUMBLE DRYING OR TUNNEL DRYING IS NOT RECOMMENDED Mattress cells can be wiped with a solution of sodium hypochlorite 1000ppm or any other non phenolic germicidal solution User Manual Diamond 8 Plus ahead of the curve Master Control Unit SWITCH OFF THE ELECTRICAL SUPPLY TO THE PUMP AND DISCONNECT THE POWER CORD FROM THE MAIN SUPPLY BEFORE CLEANING AND INSPECTION The casing of the pump is manufactured from ABS plastic If soiled it can be wiped down with a sodium hypochlorite solution to dilution of 1000ppm or any EPA approved hospital grade disinfectant Do not use phenol based cleaning solution The air filter should also be cleaned and checked as often as possible at a minimum of every six months Air Filter can be removed by pinching center of the filter and pulling outward from the back of the Therapy control unit Cleaning procedure for air filter 1 Remove Air filter
Download Pdf Manuals
Related Search