LABELMATE PM-300-B
Contents
1. POWER GREEN Indicates power is applied to the unit The ON OFF Power Switch is on the rear of the Unit ERROR STOP RED Indicates that either the unit is in STOP mode or one of the three Error Conditions has occurred 1 The unit is Out Of Paper 2 The counter has reached the Pre Set Value 3 There is a Print Head Error condition e g No more ink condition valid only if the Print Head supplies this signal INK LOW RED Indicates that the Print Head has sent an Ink Low Signal GAP YELLOW Flashes when Unit is running indicating proper detection of the Gap between successive Labels START BUTTON WHITE Start printing if no Error Condition is present STOP BUTTON RED Holding down this button will stop the machine when the next gap passes in front of the photocell SPEED CONTROL Varies the speed from zero to maximum TEST ADJUST RESET LEFT SIDE CONTROL PANEL RESET The new left side control panel has three items The toggle switch reset is a momentary closing switch that has the same function as the reset button on the counter but is more convenient for the operator ADJUST Potentiometer TEST Green LED O O o ADJUSTING THE LABEL DETECTOR PHOTOCELL The label detector photocell has been adjusted at the factory potentiometer fully CCW and requires no adjustment for a large variety of labels However some specific labels very transparent or relatively opaque backing paper mig2. FRONT PANEL HEAD CONNECTOR DB 9 FEMALE Encoder A am 6 O Gap Encoder B O2 open collector 70 No connection Ground O3 8 O Ground Head Error O4 5 up to 15V DC 90 Optional 24v O5 15v DB 9 HEAD CONNECTOR PINOUTS WARRANTY The PM 300 Reel to Reel Printer Mechanism is backed by LABELMATE s famous 3 Year Parts and Labour Limited Warranty 1 Year Warranty on Power Supplies Counters and Encoders See separate document for detailed warranty conditions MAINTENANCE Your PM 300 requires no maintenance A WARNING This Product is for indoor use only Not for use in wet locations LABELMATE LLC 69 AVENUE ALPHONSE XIII 1180 BRUSSELS BELGIUM TEL 322 375 69 60 FAX 322 375 38 96 brussels labelmate com www labelmateeurope com LABELMATE User_PM 300 B CE 02 13 Original user manual LABELMATE PM 300 8 Reel to Reel Printer Mechanism for Ink Jet Heads Secured DB 9 Print Head Connector Encoder 2 048 Pulses per Revolution Linear Resolution of 0 0407 mm Remove all parts from the shipping container and verify contents PACKAGE CONTENTS e User Manual this document e PM 300 Printer Mechanism Unit Retain the Shipping Container and Packaging for Storage and Transport SPECIFICATIONS Max Label Roll Weight 6Kg Max Label Roll Size 300mm diameter Speed Min 65cm sec Max 150cm sec for LS and 220cm sec for HS Max speeds specified with a 76mm take up roll diame
3. ht require adjustment of the photocell Load a roll of labels on the machine and position the backing paper in front of the photocell Make sure that the labels are tensioned when doing the test The LED should light on If not rotate the potentiometer till LED goes on green Now put a label in front of the photocell the LED should turn off CONTROLS ON REAR OF THE UNIT On the rear panel besides 230V input power connector and the On Off switch there are 2 other switches One controls the rewind direction to rewind with labels in or out cw STOP A t The other switch lets you decide if DIRECTION ON HEAD ERROR you want the machine to stop when an head error occurs e g low ink or simply turn on the error light on the front panel CEW WARNING DO NOT CHANGE DIRECTION WHILE THE MACHINE IS RUNNING THIS COULD PERMANENTLY DAMAGE THE MACHINE
4. ter Power Input 230V 50 60 Hz AC Input 115V on request e KEEP MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE e IMPORTANT INFORMATION e This product is a reel to reel label printer with counter It is only to be used to print rewind unwind labels to of the recommended dimensions and weight in an indoor dry environment The machine has to be unplugged before any manipulation The machine is to be used on a flat surface Do not leave the power cable in a passageway The ambient light of the working area needs to be sufficient to avoid any risk The P 300 can be used in ambient temperatures of 2 C to 40 C Connection of the machine to the power source must respect local and European legislations SET UP 1 Plug the Power Supply Output Cable to the Power Jack on the Rear Panel of the PM 300 Plug the Power Supply into a suitable AC Power Mains Outlet Place the Power Switch on the rear of the PM 300 to the ON 1 position 2 The Optional Counter if included is pre programmed as a Preset Count Up Counter To use the preset function input the desired number of labels with the Push Buttons on the Counter If you do not use preset set the value to 0 3 When the preset number of labels is reached the PM 300 will stop Pressing the Reset on the Counter will reset the count to zero so the PM 300 can be started again A duplicate Reset Switch is located on the left side of the unit FRONT CONTROL PANEL
Download Pdf Manuals
Related Search