U.motion Control
Contents
1. then using the common Android browser Once a project has been configured as described before the access to the visualisation will be started automatically by leaving the settings window The following loading screen will be shown which will then be substituted by the HOME screen of the visualisation depending on the configuration of the product the app instead of the HOME screen a login window may appear in which a valid user password combination must be inserted a U motion Control narin ntorfare oaaing interface pa Favourites Settings merten by Schneider Electric U motion Control Technical Manual The first connection to the U motion device takes around 40 60 seconds until completion since the necessary data has to be transferred from the device Once the web app has been loaded completely the connection to the device remains established and the pages of the visualisation can be access without further time delay This is accomplished by using a background service which keeps active the connection to the interface and prevents that the web app is closed automati cally by the garbage collector of Android Caution When using the app on devices without permanent power connection like for example smartphones or tablets on battery use the constant connection to the interface can reduce battery life Therefore it is possible to ter minate the app and its service at any time through the notification bar of An2. you are currently connected in your home network and therefore the U motion device can be reached through its local IP address or if instead the remote settings should be used TAKE CARE this setting is only important when you are using the automatic mode see description on next page merten U motion Control by Schneider Electric Technical Manual Enable remote access This checkbox enables the remote access function of the app If it is enabled at disabled automatic mode see next point the local settings are ignored and the remote settings for IP address and port will be used so that the app can connect to the U motion device through the mobile network requires that an appropriate port forwarding for the product has been configured further information about this topic can be found in the INSTALLA TION MANUAL of the U motion device Automatic mode BETA IBETA FEATURE full functionality is not granted If in addition to the remote access also the automatic mode is enabled the app will auto matically recognize network changes and will refresh the graphical interface in back ground If you for example leave your home network with auto mode enabled the app will automatically switch to remote access and reload the interface from the U motion device If the app afterwards is started a short info about the network change is shown and you will have immediate access to the interface without having to refresh it manually NOTE
3. U motion U motion Control Technical Manual Control app for Android devices 04 2014 Version 1 0 1 www merten com merten by Schneider Electric merten U motion Control by Schneider Electric Technical Manual GENERAL INFORMATION Schneider Electric GmbH c o Merten Gothaer Stra e 29 40880 Ratingen www merten com www merten austria at Customer care centre Phone 49 2102 404 6000 Operating instructions manuals and software are protected by copyright All rights are reserved Copying multiplication translation and conversion either partially or as a whole is not permitted You are allowed to make a single copy for backup purposes Note please read the manual before beginning and keep the manual for later use Audience the manual has been conceived and written for users who are experienced in the use of PCs and automation technology CONVENTIONS KEY Keys that are to be pressed by the user are given in square brackets e g CTRL or DEL Courier On screen messages are given in the Courier font e g C gt Courier bold input to be made by the user are given in Courier bold e g C N gt DIR double quotes Names of buttons to be pressed menus or other onscreen elements and product names are given within double quotes e g Configuration Symbolic In this manual the following symbolic are used to indicate particular text blocs Caution A dangerous situation may arise that may cause damag
4. droid please check out the follow ing two screenshots Ethernet Turn off Network configuration IP address 192 168 0 145 LAN 2000 1 1 oF 00 17 Ongoing USB debugging connected Select to disable USB debugging USB connected Select to copy files to from your computer U motion Control Click here to terminate 00 1 Compared to a common browser U motion Control has the following advantages e Quick access buttons in the TOOLBAR HOME favorites settings The app stores the current page when brought into background in this way when the application is started again it will automatically jump to the page lastly shown Optimized graphics and performance in order to use at best the possibilities of your Android device usage of HTML5 caching for the local storage of the transferred data results in a speed increase up to 70 after a one time synchronization 10 merten U motion Control by Schneider Electric Technical Manual The following screenshot shows the app displaying contents of a connected U motion device and explains the single areas of the app Menu bar with quick access Pre p buttons for the home and favor ites pages and app settings Favourites Settings ker For further information on the general usage of the U motion device please refer to its USER MANUAL 24 2 merte U motion Control by Schneider Electric Technical Manual I NOTES
5. e to material Note D Hint and additional notes merten by Schneider Electric INDEX 1 General Overview 1 1 Introduction 1 2 Requirements 2 Setup 2 1 Introduction 2 2 Installation 2 3 Configuration 3 Usage Il Notes U motion Control Technical Manual 4 4 4 5 5 5 5 G 12 merten U motion Control Technical Manual by Schneider Electric 1 GENERAL OVERVIEW 1 1 INTRODUCTION U motion is a product family for the supervision and visualisation of home amp building automation systems which have been realized on the basis of the worldwide KNX standard The U motion devices allow managing of all functions of the system through browser access from any PC MAC Touchpanel tablet and smartphone of the last generation within the same network or remotely via internet The app U motion Control was especially designed to work in combination with U motion devices The app can be classi fied as web app which shows contents that normally can also be shown through a common browser in an optimized way Note This manual was created for the usage of the app on Android based mobile devices If you are using DD the app on U motion Client Touch 7 please refer to the TECHNICAL MANUAL of it since beneath the expla nations of the apps it contains also important additional information Furthermore the representation of the app is slightly different on mobile devices 1 2 REQUIREMENTS U motio
6. er every boot the connection to the server will be established imme diately Refresh App This entry refreshes the interface of the software without clearing the cache of the mobile device see next point This process is much faster than the deletion of the cache and is enough if only small changes to the visualisation occurred Empty Cache If this menu entry is clicked the local cache of the mobile device is emptied deleted and at the next connection to the product all necessary data is downloaded again from the product This function is necessary whenever changes are made on the interface like for example change of the theme creation of new rooms etc In these cases the cache has to be refreshed before the mobile device will show the new configurations Password Protection As already mentioned this point allows defining a password which protects the access to the settings menu If this field is left empty access to the settings is granted to everybody clicking on the settings button merten U motion Control by Schneider Electric Technical Manual The Back entry will take you back to the main screen of the web app If parameters of the web app have been changed within the settings menu the connection will be refreshed automatically Note The remote settings are optional and needed only if you want to use the app to access the U motion YD device also from outside you home network However this requires that the remo
7. he U motion devices can be found in the corresponding user and installation manuals When starting the app for the first time an advice will be shown that no product has been configured yet The use of the app will only be possible if at least the IP address of the targeted U motion device is inserted A click on the Settings button opens the configuration page of the app If the settings page is protected by password the correct password must be inserted Note all screenshots within this manual were made on an Android device which according to the Android D specification is classified as display type LARGE and screen density MDPI Depending on the used device the visualisation of the app may slightly vary Nevertheless the available options within the app are always the same merten U motion Control by Schneider Electric Technical Manual The following screenshots show as well the password dialog as also the settings page ettings Local IP settings IP Address Configured IP Address 192 168 1 1 SSL Protection Check the box to enable SSL protection when accessing U motion Control Port Define the port used for accessing U motion Control default SSL 443 ni 80 Home WiFi Network Select the home network in which your U motion device is reachable through its local IP address must be currently reachable Remote IP settings Password required Enable remote access Enables the remote access to your U mot
8. in case you should have problems using this feature please get in contact with the technical support Every kind of feedback that helps to improve this functionality is welcome Remote IP Address IP address or domain name used for the remote access to the U motion device normally the public IP address of the router with the active port forwarding to the product Remote Port External port of the router which is redirected to port 443 of the U motion device for remote access only SSL protected connections are allowed Username This value refers to the user name the app should use to login to the U motion device This user name must be present in the configuration of the interface and dispose of the neces sary permissions to access the visualisation If this criterion is fulfilled the user name can be inserted in this field and in combination with the password in the next setting will cause the app to automatically login to the product If this field is left empty the app will show an extra login window where the authentication has to take place manually Password The password which is required in combination with the user name explained above in order to correctly login Show Toolbar Permits to show hide the toolbar on the lower edge of the app with the buttons HOME FAVORITES and SETTINGS App Autostart If this option is enabled the app will be automatically started after a reboot of the mobile device In this way aft
9. ion device statically o Please enter your password to access the settings sutomatically OK Cancel U motion Control authentication Username Please insert the user name as defined within U motion Control Password Please insert the user password as defined within U motion Contro The following list explains the single parameters that can be configured IP Address In this field the IP address of the targeted U motion device must be entered A click on this entry will start a scanning process which will show a list of the U motion devices found in the current network Afterwards you can select the desired IP address simply by choosing it from the list Naturally it is still possible to input the IP ad dress manually SSL Protection This checkbox enables disables the SSL protection of the connection Generally in local networks there is no need for SSL protection Therefore this option is disabled as default Depending on the previous setting the default port is either 443 SSL enabled or 80 SSL disabled If the connected device has a special network configuration e g uses port for warding and is reachable only through another port the corresponding port can be set here If you are using a standard version of the interface you can just use the default val ues already set for this field Home WiFi Network This menu entry is only shown if your mobile device is connected through WiFi In this case you can define whether
10. n Control requires a smartphone or tablet with operating system Android 2 3 or higher Furthermore it is necessary that the network in which the U motion device is installed provides WIFI access Once the app has been configured for the first time it will also be possible to connect to the device remotely using the mobile network this still requires that the remote connection to the U motion device has been configured properly as described in its INSTALLATION MANUAL Note because of the high amount of Android devices the app could not be tested on all of them If you D should experience any problems installing configuring using this app on your Android product please contact our support merten U motion Control Technical Manual by Schneider Electric 2 SETUP 2 1 INTRODUCTION U motion Control can be downloaded for free from the Google Play Store and permits to be connected to one U motion device 2 2 INSTALLATION In order to install U motion Control on your Android device please access the Play Store search for U motion Control and select the free U motion Control app At completed download the app can be started through the corresponding Icon 2 3 CONFIGURATION The following pages will exclusively handle the configuration of the web app itself This manual will neither describe the contents of the interface or its navigation nor will it enter in detail on the product features themselves All information regarding t
11. te connection to the product has been configured properly as described in its INSTALLATION MANUAL The switching between local and remote access can either be done manually or automatically BETA feature The app U motion Control can also be used in combination with the U motion Builder the useful development tool In order to configure U motion Control to work with the U motion Builder please proceed as follows Select the SETTINGS menu from the TOOLBAR of U motion Control As local IP address please specify the address of the PC on which the U motion Builder is installed and running Be sure that the SSL protection is disabled Insert 8080 as local port At completed configuration the U motion Builder can be accessed just like a real device Naturally the U motion Builder project can t send any commands on the bus or control real KNX devices but it can be perfectly used for presentation and training purposes and to get familiar with the functionalities of U motion Control When leaving the settings page after modifying the parameters the app will try to connect to the specified product During this procedure a loading screen will be shown which will be substituted by the home page of the interface as soon it is loaded completely merten U motion Control Technical Manual by Schneider Electric 3 USAGE U motion Control permits to navigate within the visualisation of a U motion device in a much faster and easier way
Download Pdf Manuals
Related Search