GVT-800 User Manual
Contents
1. Power for ignition Battery Trackers default output OUT1 OUTS3 are closed in this case P1 and p2 are connected inside Engine ignition loop the relay when the output is open relay is disconnected so we can control engine s ignition loop For example SMS 000000 WO022 1 1 Engine ignition loop disconnected SMS 000000 W022 1 0 Engine ignition loop connected Please refer to lt A command list gt for more information 6 Setup software In addition to set the tracker parameter with SMS we can set it on the PC computer with lt Setup software gt F Setup Software 20140822 1 COMM com z Open Password 000000 Ensure Password Change Password Restart Device IMEI Version Time Zone GMT v Authorized Number Geofence Photo and Voice Authorized Number SMS Format Google Link Clear Interface SMS Tracking press sos to call Tel Backup to PC pO Restore fim PC Interval 0 min Read Times External low voltage value 9 0 Vito Write Tn Set Geofence n for unlimited uploads Press 505 IN1 IN2 IN3 ACC External voltage cut off the connection alarm jm jm jm Low battery alarm Car battery low battery alarm Geofence Receive GPS signal alarm Lost GPS signal alarm GPS antennas cut off the alarm Overspeed alarm Overspeed value 0 Restore factory settings EXIT Set fatigue value 0 min Clear this page Interface Hint Please open the right serial port2. before setup the machine and close the serial port before change the serial port Impact alarm Dial up track Listen in Mode Driver fatigue alarm O i UE oe oe a a a o UA YW Ta dd a a a a U U 7 Install the device 7 1 Install I O wire I O port Identifying Function 1 VCC red DC IN Input voltage 9 33V 1 5A 2 GND black Ground 3 SOS orange SOS emergency button 4 GND black Ground 5 IN brown Digital input 1 positive triggered 6 IN2 white Digital input 2 positive triggered 7 ACC purple Digital input ACC positive triggered 8 OUT1 green Digital output 1 used for control relay or other drivable electricity 500 mA withstanding voltage 50V 9 OUT2 yellow Digital output 2 used for control relay or other drivable electricity 500 MA withstanding voltage 50V 10 OUT3 pink Digital output 3 used for control relay or other drivable electricity 500 MA withstanding voltage 50V 11 AIN2 grey Analog input 2 general connect engine temperature sensor input voltage 0 3V can customize other electric voltages 12 AIN1 blue Analog input 1 general connect fuel sensor input voltage 0 3V can customize other electric voltages 7 2 Install Navigation LCD Panel PND LCD uses resistive screen it Supports road navigation making a phone call send and receive SMS and send target location remotely etc Please connected the external power when you use it fa bani Dangli
3. or not perform proper function of application Correct Connection Chosen Accessories Installation in a Hidden Place Power off in Blasting Site Repair and Service Not Fully Water Resistance When connect to other devices please read its manual carefully Use our accessories battery and external module to avoid damage to our device In order to avoid damage by external force intentionally please install our device in a hidden place Follow related restrictions Do not use our device in blasting site Only qualified engineer with technical support can repair our device The device is not fully water resistant Keep it dry 3 Specification and parameter Items Power supply Backup battery Normal Power Consumption Size Weight Operating Temperature Humidity GSM Module GPS IC GPS sensitivity GPS frequency C A code Channel Positional accuracy Speed accuracy Time accuracy Turnover time Hot start Warm start Cold start Maximum altitude Maximum speed Maximum acceleration Working time LED Button Port Specification DC 9 33V 1 5A Rechargeable battery 750mAh 3 7V JOmA 84 mm 66 mm 30 mm 135g 20 55 C 5 95 Non condensing Quad band GSM 850 900 1800 1900 MHz UBLOX GPS IC 161dB L1 1575 42 MHz 1 023 MHz 50 channels lt 10 M 2D RMS 0 1 M S Satellite Time 1 microsecond time synchronization Average 0 1s Average 1s Average 3s Average 37s 18 000M ma
4. D SOLUTIONS 5555 17 1 Products overview Thanks for purchasing our products Tracker is a GPS GPRS based tracking device designed for heavy motorbike intercity bus school bus and fleet management It has built in terminals of GPS module and GSM communication module which are used for getting the location data and send it to authorized phone number via SMS and tracking through free maps Google Earth or Google Map at the same time the GPRS data can be sent to the internet server which can realize the checking monitoring and managing of the device on computer Tracker has the following features and functions Collision alarm 3G accelerometer Tracking regularly Geo fence alarm Over speed alarm Low battery alarm SOS emergency calling Low battery alarm No GPS signal alarm Build in 1GB memory IC Internal battery 750mAh Tracking by distance Build in 8MB flash memory GPS antenna cut off alarm External power cut off alarm Fuel engine cut off remotely Camera for taking photograph optional Navigation LCD panel optional RFID card reader optional Tracking by SMS GPRS TCP UDP Remotely monitoring or two way communication Two ways DS18B20 temperature measurement optional Three digital outputs three digital inputs and two analog inputs four RS232 ports one RS485 port Ke 2 Safety instruction Read these simple guidelines Not following them may damage the tracker
5. S485 B V 7 6 Two way communication The two way communication function can only be enabled when use the headset with microphone for Apple Samsung MINU Huawei etc Left Channel Right Channel Se Microphone 7 7 Voice broadcast Tracker supports TTL voice broadcast but this function must be customized our standard configuration is not including this 8 Problems and solutions Problem Tracker can not turn power switch on Possible cause Low battery Please connect external power Problem The tracker do not reply the SMS The GSM antenna conjunction Please reconnect the GSM antenna isn t connected firmly The GSM antenna conjunction is Make sure the GSM antenna and the GSM connecting base are connected incorrect The GSM network is busy Wait for a message The GSM network may reply slowly when busy time or equipments breakdown Password or command is wrong Please use correct password and command format Not enough SIM balance Please change or recharge the SIM card The SIM damaged or warped Please check the SIM card sweep metal of card to get in touch with a point If still invalid then replace SIM card Problem SMS received with latitude and longitude for zero Possible cause The GPS antenna conjunction isn t Please reconnect the GPS antenna connected firmly The GPS antenna conjunction is Make sure the GPS antenna links the GPS conjunction incorrect The tracker has already blocked Move the trac
6. Version Number Modified by Change Content Type Date V1 0 Amy create 2014 06 23 GPS Multi function Tracker User Manual GPS Multi function Vehicle Positioning Tracker User manual CONTENTS 1 PRODUCTS OVERV E Wecsssscnnnnnncnmmm cece nm eee CPR Ee 2 2 SAFETY INSTRUCTION ssssnnnnsss cece ne eee 3 3 SPECIFICATION AND PARAMETER ccsssssscnnnncnnnnmncnennmnESGGGGS SES CEE 3 4 GETTING STARTED sesssnnn ne ceen mee 4 4 1 HARDWARE AND ACCESSORIES siss 4 4 2 VIEW AND PORT sttcttt eee e cece e eee eee eee eee 5 4 3 FIRST USE cts ts ss 5 D PARAMETER SETTING BY SMS ssnnnnnnsnn 7 5 1 CHANGE THE PASSWORD 55 ss ceeeeeee cece eee ee eee eee 7 52 AUTHORIZED NUMBER sess 8 5 3 DEFINITE TIME TRACK siss 8 5 4 SOS EMERGENCY CALLING siss 9 5 5 TRACKING BY GPRS erste esse eee e cece eee eee eee eee 9 5 6 GEO FENCE ess 9 5 7 SET THE TIME ZONE siss 10 5 8 TRACKING BY SET THE DISTANCE OR ANGLE ss 10 5 9 INPUT APPLICATION IGNITION DETECTOR ss 10 5 10 FUEL DETECTOR cers tts tee ee sence eee eee 11 D 11 OUTPUT CONTROL COMMAND sess ss 11 5 12 OUTPUT APPLICATION sess 12 6 SET THE SOFTWAREssssssa nn 12 7 INSTALL THE DEVICEssesssnn meee 13 7 1 INSTALL I O WIRE sess 13 7 2 INSTALL LCD ss 14 7 3 INSTALL TEMPERATURE SENSOR sess ss 14 7 4 INSTALL CAMERA sess 15 7 5 INSTALL RFID CARD READER ss 15 7 6 TWO WAY COMMUNICATION siss 16 7 7 VOICE BROADCAST ss 55 cece cece eee e ee en eee eee eee eee eee e ee eee eee eae eee eee eee 16 8 PROBLEMS AN
7. harging completed or no power GSM module is initializing or calling in GSM network is not registered GSM network is registered GSM network is registered network and GPRS function works well GPS module is initializing GPS module is working normally but hasn t fixed position GPS module is working normally and has fixed position 5 Parameter setting by SMS 5 1 Change the password SMS Command SMS 000000 W001 123456 Describe change user password Explain All the SMS commands must be capitalized and please switch to English input method when you edit 1 000000 is user s password the default password is 000000 Device will only accept commands from a user with the correct password Otherwise command will be ignored 2 123456 is the new password password must be 6 digits For example SMS 000000 W001 123456 5 2 Authorized number SMS Command SMS 000000 W010 NO Phone Number ABCDEFGHIJKLMNOP Describe set the authorized phone numbers to receive SMS alarms Explain NO serial number must be 1 or 2 or 3 Phone Number authorized phone numbers Max 16 digits A SOS BIN1 C IN2 D IN3 ACC E Cut external power off alarm F Low battery alarm G Car battery is low alarm H Geo fence alarm I Receive GPS signal alarm J Lost GPS signal alarm K Cut GPS antenna off alarm L Over speed alarm M Hitting alarm N Tracking by calling O Answer the phone automatically P Fatigue dr
8. hone to make sure it can send and receive SMS Make sure that lock code of the SIM card is turned off If you need the function of sending an SMS location report to the authorized phone number when it makes a call to the tracker please make sure the SIM card installed supports displaying caller ID Insert the SIM card Unscrew the front cover of the tracker as follow attention The device must be turned off when you insert the SIM card Please make sure the bevel edge of the SIM card is outward and its metal surface facing down when you find the SIM card slot and insert it then slide the power switch to left and turn it on As follow ON OFF WIS oJoru 4 3 2 Connect the antenna connect the GSM antenna to the golden port Attention the GSM antenna is omni directional antenna so that it can be installed far away from the power source and anywhere hidden in the car connect the GPS antenna to the white gold port Attention GPS antenna is directional antenna It is better to fix it to face the sky directly and flat side down black side up and use double side tape keep it fixed otherwise the GPS signal will be affected 4 4 LED indication Red Power indication Always On Always OFF Blue GSM indication 0 3S On and 0 3S Off Always On 1S On and 3S Off 0 1S On and 3 S Off GPS indication 0 3S On and 0 3S Off 1S On and 3S Off 0 1S On and 3S Off N Power charging Power c
9. iving warning 1 enable 0 disable For example Set the first authorized phone number is 13800000000 and just enable SOS alarm function SMS 000000 W010 1 13800000000 1000000000000000 5 3 Tracking by preset time interval SMS command SMS 000000 W013 Phone Number x Y Describe set the time interval and the number of times of sending SMS Explain 1 X stand for time interval Max is 65535 unit is minute 2 X 0 means disable this function 3 Y means the number of times of sending SMS 4 Y 0 means device will send unlimited SMS For example SMS 000000 W013 13800000000 30 0 When enable it tracker will send location SMS to every authorized phone number oO 5 4 SOS emergency calling SMS command SMS 000000 W011 Num Describe if press SOS button for 3 seconds the tracker will call the SOS phone number Explain Num phone number Max 16 digitals For example SMS 000000 W011 13500000000 Set the SOS number is 13500000000 5 5 Tracking by GPRS SMS Command SMS 000000 W002 APN Username Password W003 IP Port W004 ID W005 X W009 Y Description enable GPRS tracking function Explain 1 APN access point name of network 2 Username and Password are optional If you don t know what they are please just input APN only 3 APN Username Password should not be over 64 characters 4 IP server IP address or domain name 5 Port Max 65535 6 ID device ID 7 X GPRS upload interval u
10. ker to open area w o any tall building tree and heavy the GPS signal raining Those can shield GPS signal The GPS signal is weak Place the GPS antenna face to the sky problem Can not connect the server by GPRS Possible cause The SIM card can not support the Enable the SIM card s GPRS function GPRS function The GPRS function has been Enable the GPRS function disable Incorrect IP address or PORT Get the right IP address and port then reset the device The GSM signal is weak Move the tracker to a place with strong GSM signal
11. mand SMS 000000 W006 X W007 Y Describe this command used for enable this function X is distance value unit is meter Y is angle value unit is degree Suggest X 100 Y 15 For example SMS 000000 W006 100 W007 15 5 9 Input application Ignition detector Power for ignition Digital input 3 ACC used for ignition detection The detection flag and alarm will be sent to the server through GPRS when flag changes Please refer to lt GPRS Communication Protocol gt for more information 5 10 Fuel detector HE VCC AIN1 AIN2 GND Analog input AIN1 used for oil detection range 0 3V If there is other sensor you want to use please make sure its voltage is suitable Oil value is the one with highest precision Max 2 The remaining oil percent will be sent to the server via GPRS The remaining oil percent AIN1 4096 100 AIN1 value is the data to be uploaded to server by GPRS Please refer to lt GPRS Communication Protocol gt for more information 5 11 Output control command SMS command SMS 000000 W022 NO X Describe enable disable this output Explain NO O 4 1 refer to digital output 1 2 refer to digital output 2 3 refer to digital output 3 4 refer to digital output 4 X 1 open the output so that it can drive the relay X 0 close the output For example SMS 000000 W022 1 0 5 12 Output application 12V DC White OUT1 OUT3 Y Yellow P1 P2 e
12. ng ee O Blue GPS RX Port of receiving GPS data White GND 7 3 Install temperature sensor It uses DS18B20 the measuring range of temperature is 125 C 55 C up to support two ways temperature sensor Waterproof and the longest wire length can be customized to 5m Yellow T2 Temperature detection has two ways output this is second way Red VCC Power output s port also can work normally without external power source Yellow Ti Temperature detection has two ways output this is first way 7 4 Install camera Tracker supports three ways photographing and auto light compensation at night Its working voltage is 5V Attention if you want to take a photograph please make sure the tracker connected the external power Standard configuration is three ways RS232 connected camera RS232 s port also can be customized to connect other equipments Black GND Ground z Greed RS232 TX RS232 send port 3 Red The power output port only when connected the external power source the power output voltage is 5V Yellow RS232 RX RS232 receive port 7 5 Install RFID card reader It uses RS485 bus communication convenient to add other RS485 equipments working voltage is 5V It can be enabled only when engaged with an external power source Black GND Greed RS485A RS485 A V 3 Red 5V The power output port only when connected the external power source the power output port is 5V 4 Yellow RS485B R
13. nit is seconds 8 Y GPRS upload mode range of 0 2 O means disable GPRS function 1 means upload by TCP 2 means upload by UDP Example SMS 000000 W002 cmnet W003 192 168 1 1 8088 W005 60 W009 1 5 6 Geo fence SMS command SMS 000000 W018 NO name lat Ing radius Describe enable Geo fence alarm When the tracker moves in out the preset geo fence tracker will send an alarm by SMS to the authorized number and send this data to server if GPRS is connected Explain NO serial number for geo fence must be 1 to 5 name max 10 characters lat Latitude format is dd dddddd the unit is degree if it is northern latitude minus is needed Otherwise omit it Ing Longitude formats is ddd dddddd the unit is degree if it is east longitude minus is needed Otherwise omit it radius Max 99999 00 the unit is Km Based on preset longitude and latitude as the center of the circle and the preset radius a circle is defined For example SMS 000000 W018 1 school 22 12345 114 12345 10 50 SMS 000000 W018 2 office 12 12345 45 12354 10 75 5 7 Set the time zone Set the time zone of SMS SMS command SMS 000000 W020 X Describe Choose time zone of SMS time zone default is GMT O Explain X time zone value please plus in front if it is a negative otherwise ignore it Unit is minutes New York s time zone is 300minutes For example SMS 00000 W020 480 5 8 Tracking by distance or angle SMS Com
14. ximum 60 000 feet 500 m s maximum 1000 knots Less than 4g About 7 hours 3 LED lights to show Power GPS and GSM status SOS button for making phone calls sending position and giving a warning SMS 3 digital outputs 3 digital inputs 2 analog inputs 4 RS232 ports 1 RS485 port 4 Getting Started This section will describe how to set the tracker 4 1 Hardware and accessories Terminal GSM antenna GPS antenna Batterv included gt e I O connecting wires USB cable Standard accessories Optional accessories Navigation LCD panel PND Two ways temperature sensor Camera At most support three ways aN SS KI C lt RFID card reader Headset with microphone gt 4 2 View and port GPS antenna port GSM antenna port Power switch SIM card slot Micro USB port Camera Camera2 Camera3 RS485 RFID Speaker port I O port LCD Temperate sensor Two way communication port 4 3 First use Please read this manual before using tracker and check if all parts are included in the packaging box 4 3 1 Ensure that your tracker has a working SIM card installed and turn the power switch on SIMCARD J 1a Our device only supports micro SIM card if itis large please go to the local operator and cut it become the micro SIM card do not cut to the nano SIM card Check the SIM card has not run out of credit money please test the SIM card in a p
Download Pdf Manuals
Related Search