Model 402KL Physician Beam Scale User Instructions
Contents
1. support with any questions or concerns regarding the use of the counterweight set Counterweiqht Instructions for Weighing in Pounds Ib Note The 100 Ib counterweight is required when weighing patient who is over 390 Ibs Counterweiqht Instructions for Weighing a Patient 391 400 Ib 1 When a patient weighs between 391 400 Ib place the lower poise weight at 250 Ib Place the 100 Ib counterweight on the 3 notch from the left between the 50 and 100 Ib value 3 Adjust the small poise weight to match the patient weight The poise bar will center in the trig loop Note To read patient weight refer to Recording Patient Weight section below 4 Read and record the weight Counterweiqht Instructions for Weighing a Patient 401 440 Ib 1 When a patient weighs between 401 440 Ib place the lower poise weight at 300 Ib Place the 100 Ib counterweight on the 3 notch from the left between the 50 and 100 Ib value 3 Adjust the small poise weight to match the patient weight The poise bar will center in the trig loop Note read patient weight refer to Recording Patient Weight section below 4 Read and record the weight Counterweiqht Instructions for Weighing a Patient 441 490 Ib 1 When a patient weighs between 441 490 Ib place the lower poise weight at 340 Ib Place the 100 Ib counterweight on the 3 notch from the left between the 50 and 100 Ib value 3 Adjust the small poise2. Number 55000 for storage or for transport from one room to another This scale does not include 55000 Wheel Bracket and must be acquired separately To prepare the scale for transport follow these steps Caution It is recommended that the assembly be performed by two persons 1 Remove the mounting screws attaching the clamping plate to the wheel bracket 2 Tip the scale forward until top front of the pillar is resting on the floor 3 Position the clamping plate inside the base and align the clamping plate wheel bracket and base assembly holes 4 Install the mounting screws through the wheel bracket base and clamping plate Tighten the mounting screws securely Carefully tip the scale to its upright position 6 Totransport the scale tip the scale pillar back until the scale is supported by the wheel bracket Carefully move the scale to its new location Required Parts 1 402KL 1 Wheel Bracket Part Number 55000 Note Wheel bracket is not included Tools Required not included Adjustable wrench or 10mm wrench 10 Figure 7 CLAMPING PLATE WHEEL BRACKET N T MOUNTING To ul SCREWS Figure 8 11 Ve Clamping plate t Figure 9 Wheel bracket Mounting screws Figure 10 12 OPERATING INSTRUCTIONS Zero Balance Adjustment see Figures 11 13 The scale should be checked p
3. small poise value to the indicated reading of the large poise value The total amount is your weight Weighing Hints 1 Weigh yourself at approximately the same time each day The foods you eat the liquids you drink and your level of activity will cause your weight to vary during the day 2 For accurate measurements weigh yourself without clothing The average weight of clothing including shoes is about 2 5 Ib 0 90 2 26 kg for women and 5 8 Ib 2 26 3 62 kg for men 13 Upper poise weight Upper poise bar Health o meter Figure 11 Pounds Ib mv Kilograms kg Health o meter Trig loop Figure 12 14 OPERATING INSTRUCTIONS CONT 7 Value reads 29 75 Ib 29 Ib 12 oz W E r M do s 5 17 Value reads 13 5 kg ror Combined value 100 Ib 29 75 Ib 129 75 Ib or Combined value 100 Ib 29 Ib 12 oz 129 Ib 12 oz Value reads 100 Ib Figure 13 15 COUNTERWEIGHTINSTRUCTIONS Counterweight Instruction see Figures 14 20 In order to increase the scale s capacity to a maximum value of 490 Ib 210 kg the counterweight set 55090 must be acquired The scale can be easily assembled with counterweight set Part Number 55090 for whole set 55080 for counterweight in pounds and 55085 for counterweight in kilograms In order to employ the counterweight set refer to the instructions below Contact technical
4. Dimensions Platform Standing Area Width 16 34 42 6 cm Width 10 12 26 7cm Depth 20 50 8 cm Depth 14 35 6 cm Height 57 72 146 1 cm Height 3 7 6 cm Weight 43 Ib 19 5 kg Certification Descriptions Pelstar LLC has been officially certified as the manufacturer IS 01 3485 2003 of Health meter Professional medical devices The Pelstar CERTIFIED LLC quality assurance system covers the development production sales and service of medical scales and measuring systems 402KL Scale Disposal This Health meter Professional scale must be disposed of properly as steel waste Follow the national regional or local regulations which apply to you for disposal of steel waste CUSTOMER SERVICE INFORMATION The 402KL physician beam scale is shipped disassembled in one carton Carefully inspect the carton for shipping damage before unpacking If damage is found contact Customer Service For further information or telephone support please contact Customer Service at Telephone 1 800 815 6615 Email HomProCS homscales com 402KL ASSEMBLY INSTRUCTIONS Before Assembly Each 402KL physician beam scale is shipped disassembled in one carton Carefully inspect the carton for shipping damage before unpacking If damage is found contact your shipper or a Health meter Professional representative immediately Claims must be filed with the shipper as soon as possible after receipt of t
5. Health o meter nr 3 I Model 402KL Physician Beam Scale User Instructions P N UM402KL Rev 1 011513 Health meter Model 402KL Thank you for your purchase of this Health o meter Professional product Please read this manual carefully and keep it for easy reference or training TABLE OF CONTENTS NNN 3 Specifications for This 5 8 3 Certifications Disposal Service 4 Assembly Instructions 402KL Scale VU 5 ENN 10 Operating Instructions rrrnnnrrrnnnrrrnnnrrrnnnrrrnnnennnnnennnnsennansennansennnssennansennnnsnnnnnsnnnnnee 13 CCOBUmterwelghr LAS IA CUIO EE 16 Height Measurement Instructions 21 TOUDE SPOON ES HEEe 23 ME el RR EN 24 AAA 25 Note This scale has been factory calibrated and does not require calibration prior to use Please register your scale for warranty coverage at http www homscales com customer registration aspx For User Instructions updates and revisions please go to http www homscales com 2 CAUTION AND WARNING e prevent injury and damage to your scale please follow these instructions very carefully e To prevent injury as well as scale damage during assembly exercise caution when assembling the scale pillar e Assemble and operate the scale per the enclosed user instructions e For accurate weighing this scale must be placed on a flat stable surface e For accurate
6. able replacement may be made with a similar product of equal or greater value All parts including repaired and replaced parts are covered only for the original warranty period Who is Covered The original purchaser of the product must have proof of purchase to receive warranty service Please save your invoice or receipt Pelstar dealers or retail stores selling Pelstar products do not have the right to alter or modify or any way change the terms and conditions of this warranty What is Excluded Your warranty does not cover normal wear of parts or damage resulting from any of the following negligent use or misuse of the product use on improper voltage or current use contrary to the operating instructions abuse including tampering damage in transit or unauthorized repair or alternations Further the warranty does not cover natural disasters such as fire flood hurricanes and tornadoes This warranty gives you specific legal rights and you may also have other rights that vary from country to country state to state province to province or jurisdiction to jurisdiction To get Warranty Service make sure you keep your sales receipt or document showing proof of purchase Call 1 800 638 3722 or 1 708 377 0600 to receive a return authorization RA number which must be included on the return label Attach your proof of purchase to your defective product along with your name address daytime telephone number and description of the p
7. d or dropped on the scale may cause it to operate incorrectly In order to prevent this do not store or leave anything on the scale 5 If your scale fails to work properly do not attempt to dismantle it This will void your warranty See warranty information instructions on having your scale serviced 6 All bearings and working parts are permanently lubricated DO NOT USE OIL OR LUBRICANTS RE CLEANING Proper care and cleaning is essential to ensure long life of accurate and effective operation 1 Clean all external surfaces with clean damp cloth or tissue Mild antimicrobial or antibacterial soap and water solution may be used Dry with clean soft cloth 2 Do not immerse the scale into cleaning or other liquid solution 3 Do not use abrasive cleaners 24 WARRANTY 10 Year Limited Warranty What does the Warranty Cover Health o meter Professional scales are warranted from date of purchase against defects of materials or in workmanship for period of ten 10 years If product fails to function properly return the product freight prepaid and properly packed to Pelstar LLC see To Get Warranty Service below for instructions If the manufacturer determines that defect of material or in workmanship exists the customer s sole remedy will be repair or replacement of the scale at no charge Replacement will be made with new or remanufactured product or component If the product is no longer avail
8. ece down until it rests on the patient s head Determine the patient s height by reading the value on the measuring strip nearest to the line on the indicator see Figures 25 27 Figure 21 Figure 22 Figure 23 Figure 24 HEIGHT MEASUREMENT INSTRUCTIONS Inches read 41 Inches read 69 3 8 41 3 8 3 8 69 3 8 Figure 25 Figure 26 Figure 2 22 TROUBLESHOOTING Troubleshooting Before contacting service personnel refer to the following instructions to check and to correct any failures for incorrect weight measurements The accuracy of the 402KL scale when calibrated at the factory is within 0 1kg or pound For the most accurate weight measurement use the scale on hard level surface and stand in the center of the platform If the error seems excessive check the following Symptom Possible Cause Corrective Action Questionable weight or Bar does not 0 balance The balance ball must be the scale does not center balanced such that the equally in the trig loop when pointer comes to rest in the the poise weight is 0 value center of the trig loop when both poise weights are set at 0 value Ensure that the large and small poise weights are firmly against the shoulder of the beam Adjust the balance ball screw by turning the screw at the left end of the bar Bar does not move freely Bar sticking or adjustment Check if the pointer is needed touching the s
9. eriodically particularly when moved by following the instructions below Note A flat head screwdriver is required 1 Ensure that the scale is located on a hard flat and level surface Step on and off scale several times in order to align all internal parts 2 Place both poise weights on the 0 value on both bars The beam pointer should float gently up and down and not touch the top or bottom of the trig loop 3 Ifthe beam pointer is not centered in the trig loop opening rotate balance ball screw to correct the beam pointer Weighing Instructions 1 Set the large and small poises to indicate your approximate weight 2 Step onto the scale Continue to adjust the small and large poise weights until the pointer is centered Note It is not necessary for you to wait for the pointer to stop moving in order to read your correct weight As long as the pointer is moving equally within the trig loop opening the patient s weight can be determined 3 The patient weight can be recorded in either pounds or kilograms 4 Observe the location of the indicator arrow built into each poise weight Read the value on the poise bar closest to the indicator arrow 5 For easy identification pounds Ib have black graduations on a silver background located on the upper portion of each poise bar kilograms kg have silver graduations on a black background located on the lower portion of each poise bar 6 Add the indicated reading of the
10. he package The following information details what you will find inside the main carton as you unpack the parts for assembly To prevent scratching any components and avoid damaging the scale parts when unpacking do not use box cutter knife scissors or any sharp object to open the protective inner packaging Carefully remove each assembly from the carton and unwrap the packing materials Set the carton aside for storage Parts List Carton 1 Scale platform 1 Pillar 4 Pillar nuts 1 User instructions 1 Wrench Tools Required Wrench included 402KL ASSEMBLY INSTRUCTIONS CONTINUED Assembling the 402KL Scale Refer to Figures 1 6 Caution It is recommended that the assembly be performed by two persons 1 Carefully remove the scale platform and pillar from the carton Place the scale platform and pillar on a flat level and dry surface Using a table can be helpful for assembly of 402KL scale see Figures 1 amp 5 Remove the four pillar nuts and wrench from the carton Locate the steel rod at the base of the pillar see Figures 4 5 amp 6 Cut the tie wrap that holds the steel rod to the pillar studs see Figure 3 Insert studs into the four holes provided in the scale platform See Figure 2 Or L ee OG AD Tip the scale platform at an angle resting the top of the pillar on any convenient support Using the wrench provided secure the pillar to the scale platform with the four nuts See Fig
11. ide of the trig loop in Its range of travel Realignment of the beam may be necessary if it is touching Ensure that the large and small poise weights are firmly against the shoulder of the beam Adjust the balance ball screw by turning the screw at the left end of the bar Platform rocks excessively or Base out of alignment Contact technical support touches base at any corner Beam does not move at all Scale may have improper Reset the weights to lower during weighing process steel rod connection or poise weight weight may have been set at Ensure the steel rod is a higher weight than patients connected properly refer to actual weight Assembly Instructions on page 6 For further assistance please contact technical support toll free at 1 800 638 3722 23 wANTENANCE I The following provide instructions for maintenance and cleaning for the 402KL Maintenance operations other than those described in this manual should be performed by qualified service personnel MAINTENANGE Before first use and after periods of non use check the scale for proper operation and function If the scale does not operate correcily refer to qualified service personnel Check overall appearance of the total scale for any obvious damage wear and tear Do not store near chemicals heaters or radiators Do not drop kick or jump on the scale This scale is sensitive weighing device Items such as clothing or towels place
12. roblem Carefully package the product and send with shipping and insurance prepaid to Pelstar LLC Attention R A Return Department 9500 West 55 Street McCook IL 60525 If your scale is not covered by warranty or has been damaged an estimate of repair costs or replacement costs will be provided to you for approval prior to servicing or replacing PELSTAR LLC 9500 West 55 Street McCook IL 60525 USA 1 800 638 3722 or 1 708 377 0600 PLEASE REGISTER YOUR SCALE FOR WARRANTY COVERAGE AT http www homscales com customers registration aspx Health o meter is a registered trademark of Sunbeam Products Inc used under license Health o meter Professional products are manufactured designed and owned by Pelstar LLC We reserve the right to improve enhance or modify Health o meter Professional product features or specifications without notice O Pelstar LLC 2013 18013485 2003 CERTIFIED P N UM402KL Rev 1 011513 25
13. ures 4 amp 5 7 Pull the steel rod toward the base of the scale platform by grasping the finger pull loop on the steel rod end see Figures 4 5 amp 6 Push the lever extension toward the pillar with your hand see Figure 4 5 amp 6 9 While holding this position hook the steel rod to the hole at the end of the lever extension Release the finger pull loop and ensure that the steel rod and lever extension is hooked together 10 Carefully position the scale to its upright position 11 The scale is now assembled and is ready for use see Figure 1 Note To transport your scale acquire the optional wheel bracket Part Number 55000 Please refer to the Transportation section for assembly instruction Note To increase your scale s capacity acquire the optional counterweight set Part Number 55090 Please refer to the Counterweighis section for user instruction 402KL ASSEMBLY INSTRUCTIONS CONTINUED 402KL Assembly Figure 1 SCALE PLATFORM sug 402KL ASSEMBLY INSTRUCTIONS CONTINUED Finger pull loop Figure 3 Finger pull loop Pillar nuts Figure 4 402KL ASSEMBLY INSTRUCTIONS CONTINUED STEEL ROD FINGER PULL LOOP gt LEVER EXTENSION SCREW Figure 5 Pillar nuts Finger pull loop Steel rod i TRANSPORTATION I Preparing a 402KL Scale for Transportation see Figures 7 10 This scale can be easily assembled with a wheel bracket Part
14. value indicated on the lower and upper poise bars along with the counterweight at the 3 notch on the lower poise bar For example If a patient weighs 441 Ib 1 When a patient weighs 441 Ib place the lower poise weight at 340 Ib Place the 100 Ib counterweight on the 3 notch from the left between the 50 and 100 Ib value 3 Adjust the small poise weight to match the patient weight The poise bar will center in the trig loop 4 Add the weight value indicated on the upper and lower poise bars as well as the additional 100 Ib counterweight 340 Ib 1 Ib 100 Ib 2 441 Ib Patient s weight is 441 Ib 17 COUNTERWEIGHT INSTRUCTIONS CONT Counterweiqht Set 55090 Figure 14 3 Notch from the left E Ms Health me f E E i Figure 15 18 COUNTERWEIGHT INSTRUCTIONS CONT Health o meter Figure 18 19 COUNTERWEIGHT INSTRUCTIONS CONT 171 190 kg Assembly et me VENE NNNM tt LA Figure 19 191 210 kg Assembly Figure 20 20 HEIGHT MEASUREMENT INSTRUCTIONS Height Measurements Refer to figures 21 27 Note patient needs to be minimum of 23 5 8 600mm in height for the height to be accurately measured 1 X9 Raise the headpiece above the patient s head Position the patient against the height rod Ensure that the patient s posture is upright and that the patient s head is straight and level Push the headpi
15. weighing verify before each use the proper operation according to the procedure described in this manual e Do not transport the scale with any weight on the platform e Do not exceed recommended weight limit of 390 Ib 180 kg or 490 Ib 210 kg with optional counterweights for this scale e Do not use in the presence of flammable or explosive materials e If the scale becomes damaged it should not be operated until properly serviced All repairs should only be performed by authorized Health o meter Professional service personnel e To prevent patient injury the patient must be attended throughout the entire weighing event SPECIFICATIONS FOR THIS SCALE General The Model 402KL physician beam scale employs a proven and rugged mechanical design to measure patient weight and height Each precision scale is designed to provide accurate reliable and repeatable weight measurements In addition each scale is designed to provide the user with features that make the weighing process simple fast and convenient Weight is displayed in pounds lb or in kilograms kg Height is displayed in inches in or in centimeters cm 402KL Scale Specifications Capacity 390 Ib 180 kg Capacity with optional 490 Ib 210 kg counterweights Environmental Operating temperatures 50 F to 104 F 10 to 40 Storage temperatures 50 F to 104 F 10 to 40 Maximum Humidity 8596 RH Physical Dimensions Scale Overall
16. weight to match the patient weight The poise bar will center in the trig loop Note To read a patient weight refer to Recording a Patient Weight section below 4 Read and record the weight 16 COUNTERWEIGHT INSTRUCTIONS CONT Counterweiqht Instructions for Weighing in Kilograms kg Note The 30 kg counterweight is required when weighing a patient who is over 170 kg Counterweiqht Instructions for Weighing a Patient 171 190 kg 1 When patient weighs between 171 190 kg place the lower poise weight at 140 kg 2 Place the 30 kg counterweight on the 3 notch from the left between 20 and 40 kg value on the lower poise bar 3 Adjust the small poise weight to match the patient weight The poise bar will center in the trig loop Note To read a patient weight refer to Recording a Patient Weight section below 4 Read and record the weight Counterweiqht Instructions for Weighing a Patient 191 210 kg 1 When a patient weighs between 191 210 kg place the lower poise weight at 160 kg 2 Place the 30 kg counterweight on the 3 notch from the left between 20 and 40 kg value on the lower poise bar 3 Adjust the small poise weight to match the patient weight The poise bar will center in the trig loop Note To read a patient weight refer to Recording a Patient Weight section below 4 Read and record the weight Recording a Patient Weight To read the patient s weight add the weight
Download Pdf Manuals
Related Search