FLITE 395-GPRS-DNP3
Contents
1. Digital Input 5 Off Digital Input 5 On Digital Input 6 Off Digital Input 6 On Absence Digital Output 1 open Digital Output 1 open Absence Digital Output 1 close Digital Output 1 close Absence Digital Output 2 open Digital Output 2 open Absence Digital Output 2 close Digital Output 2 close Modem Reset Modem Fault Modem OK Modem answer NOK Modem answer OK GSM DOWN GSM UP GPSR DOWN GPRS UP Network access denied GSM or GPRS Network access accepted PPP session failed PPP session established IP traffic timeout IP traffic enabled Long Range Communication failed Long Range Communication succeeded Ping test NOK Ping test OK End of Directional FPI fault Directional Fault Cyclic Dial Up Equipment start Events loss Ext comm pb DNP3 Stack under 70 DNP3 Stack over 80 DNP3 Stack ready DNP3 Stack overflow NT00191 EN 01 Schn eider Electric 16 FLITE395 GPRS DNP 3 0 SOLAR version consideration Introduction The solar panel sizing has been studied for 10 minutes of communication a day In GPRS the equipment is in communication in the following phase network connection at start up duration 30s network connection on daily reset duration 30s network connection on provider disconnection 9 duration 30s Protocol transmission duration depends of protocol settings Ping transmission 5 seconds 12. No Digital input 3 yes Starting time min 0 Digital input 4 yes hour 12 Digital input 5 Yes Period hours 24 Digital input 6 yes Stack overflow yes Escape Exit Alarm message and cyclic dial up must be disabled DNP3 TCP IP parameters MERLIN GERIN Configuration and Diagnostic ALT F4 Exit F2DGPL PARAMETERS Local port 20000 Keepalive timeout 1 TCP connect delay tst ey 15 Os random value 2nd try Imn 3rd try 2mn SCADA PARAMETERS IP address 2 192 168 1 1 Remote port 2 20000 Escape Exit NT00191 EN 01 Schneider 20 FLITE395 GPRS DNP 3 0 In TCP server mode the keepalive timeout must be inferior to the SCADA ping frequency delay measurement request is recommended To limit the energy budget to 2 minutes the period must be above 1 hour MERLIN GERIN Configuration and Diagnostic ALT F4 Exit GPRS Parameters SIM CARD PARAMETERS PIN code 0000 GPRS COMMUNICATION PARAMETERS APN Server Max 30 Digits APN Login Max 30 Digits APN Password Max 30 Digits Time between connection attempt Specific Ping IP Address Ping time Ping delay s Ping number Daily disconnect Escape Exit 1h 83 206 1 3 Test 1h 5 3 If GPRS network is not available for a long period of time the equipment must not waste too much of energy by trying to connect t
3. 3 s NT00191 EN 01 Schneider P Electric 23 FLITE395 GPRS DNP 3 0 Reports Binary Input Change Events when no specific variation requested O Never Only time tagged Only non time tagged O Configurable to send both one or the other attach explanation Reports time tagged Binary Input Change Events when no specific variation requested Never Binary Input Change With Time Binary Input Change With Relative Time Configurable attach explanation Sends Unsolicited Responses O Never MConfigurable attach explanation Only certain objects Sometimes attach explanation ENABLE DISABLE UNSOLICITED Function codes supported Sends Static Data in Unsolicited Responses M Never O When Device Restarts O When Status Flags Change No other options permitted Default Counter Object Variation No Counters Reported L1 Configurable attach explanation LIDefault Object 20 Default Variation 01 Point by point list attached Counters Roll Over at No Counters Reported Configurable attach explanation L1 16 Bits 32 Bits O Other Value Point by point list attached Sends Multi Fragment Responses Yes O 00191 01 Schneider 24 FLITE395 GPRS DNP 3 0 Implementation Table OBJEC
4. the SCADA must send synchronization When IIN indicates that the equipment restarts the SCADA must send an integrity polling Class 1 follow by class 0 polling Alarm message parameters must be enabled and the alarms on DI and Stack over 80 bit must be enabled A daily connection Cyclic Dial Up must also be configured to check the status the equipment once a day To monitor the IP connection it is recommended to activate ping features on a remote IP If the ping failed the FLITE395 will restart the modem and re establish the IP connection 00191 01 Schneider 8 Electric FLITE395 GPRS DNP 3 0 Main menu RTU address e May take every value between 0 and 65534 Default value is 0 SCADA address e take every value between 0 and 65534 e Default value is 0 DNP3 Parameters Displays the configuration screen of protocol dedicated parameters Modem type e Defines the communication medium Possible values GPRS e inthis example default value is GPRS DNP3 TCP IP parameters Displays the configuration screen of TCP IP dedicated parameters GPRS Parameters Displays the configuration screen of GPRS dedicated parameters NT00191 EN 01 MERLIN GERIN Configuration and Diagnostic ALT F4 Exit Directional Gliwice ZE PROM v1 00 PARAMETERS SETUP Equipment name GLIWICE Alarm Parameters DNP3 Setup Setup Time RTU address 2 0 SCADA address 0 DNP3 Parameter
5. 241 Quest F 01700 St Maurice de Beynost Tel 33 0 4 78 55 13 13 Fax 33 0 4 78 55 50 00 http www schneider electric com E mail telecontrol schneider electric com NT00191 EN 01 09 2008 NT00191 EN 01 As standards specifications and designs develop from time to time always ask for confirmation of the information given in this publication Publication production and printing Schneider Electric Telecontrol Made in France Europe Schneider 30
6. Parameters SIM CARD PARAMETERS PIN code 0000 GPRS COMMUNICATION PARAMETERS APN Server Max 30 Digits APN Login Max 30 Digits APN Password Max 30 Digits Time between connection attempt 1 Specific Ping IP Address 0 0 0 0 Ping time 1h Ping delay s E Ping number 2 73 Test 0 min Daily disconnect Escape Exit APN Server Enter the APN Access Point Name which you obtain from your GPRS provider e APN Login and Password Enter the login and the password provided with your GPRS account Note In major case no login and password are required for GPRS access Time between connection attempt e Delay time between 2 failed connection attempts to the IP network e Default value is 1min A it is recommended to chose 1 hour Daily disconnect Hour and minutes of the daily modem reset time Specific Ping IP Address e Internal Pingable IP address if available in order to monitor the IP connection If 0 0 0 0 IP is configured the ping process is disabled Default value is 0 0 0 0 Ping test When a configuration has been saved and the product is connected to the IP network see modem state on equipment state menu a ping test can be performed using this control Possible answer In progress a ping test is in progress OK ping succeeded NOK ping failed Not available Modem is not IP connected or a periodic ping is already in progress or the m
7. 01 F2DGPL PARAMETERS Local port Keepalive timeout TCP connect delay 1st try 0s random value 2nd try 3rd try SCADA PARAMETERS IP address Remote port Escape Exit MERLIN GERIN Configuration and Diagnostic ALT F4 Exit DNP3 TCP IP parameters 20000 10mn 1s imn 2mn 192 168 1 1 20000 TCP IP connect delay Time to send an alarm configured with delayed option first attempt adjustable from 0 to 1min per steps of 1s Setting it to 0 selects a random time between 0 and 1 min this is mandatory to prevent all equipment calling the SCADA at the same time e second attempt configurable from 0 to 5min per steps of 1min Setting it to 0 selects a random time between 0 and 5 min e third attempt configurable from 0 to 10 min in steps of 1 min Setting it to 0 selects a random time between 0 and 10 min Note The 2nd and 3rd emissions are only used by the equipment if the preceding one did not manage to send the frame Scada parameters IP address e Enter the destination IP address of the SCADA Remote port e Enter the port number on which the SCADA is reachable Default value is 20000 Schneider Electric 12 FLITE395 GPRS DNP 3 0 DNP3 Parameters Idle line delay e minimum line idle interval between two consecutive frames Values are from 10 to 100 ms e 10msis the default value Requires Data Link Layer C
8. DI 6 0 at start 99 is faulty 0 31 received signal 17 Escape Exit Modem state comments Modem Init FLITE395 is configuring the modem Entering code pin Code pin error Wrong code pin Network registration IMSI registration GPRS registration PDP Init Open a PDP session PDP Closing Close the PDP session PDP Status Check the PDP status PDP Connected Modem is connected to ip network Ping A ping is in progress Closing TCP listened Close the listen port TCP Closing Disconnection from the SCADA TCP Listening Opening the listen port TCP Listened Stand bye state when listen mode is activated TCP Connecting Try to connect to the SCADA TCP Connected Connected to the SCADA Modem failure GSM registration denied IMSI registration is refused by the operator check your SIM card right with your provider GPRS registration denied GPRS registration or PDP activation is refused by the operator check your SIM card right with your provider Schneider 14 FLITE395 GPRS DNP 3 0 DNP3 Analyser p MERLIN GERIN Configuration and Diagnostic ALT F4 Exit gt 06 26 89 gt gt 05 64 1 44 02 00 01 00 5 El D3 82 00 00 02 02 17 02 01 01 50 9A 2A 11 1A D5 This analyser shows the different frames TT PRA on G
9. ITE395 can work as TCP server or TCP client Unsolicited message have to be enabled in both cases to limit the flow of message In this case no permanent polling needs to be done Use as a TCP server In this mode the TCP connection is always established and maintained by the SCADA The TCP connection is monitored by the SCADA with a Keep Alive mechanism We recommend using an application message as delay measurement or Class 0 but the consumption is higher for keep alive message In this case the alarm message parameter must be disabled and no Cyclic Dial up has to be activated The Keepalive timeout on the FLITE395 has to be configured a little bit higher than the keep alive frequency one minute higher configured on the SCADA size Only application messages are taken into account by FLITE395 to reset the timer The frequency of the Keep alive can be configured from 10s to 3600s by 10s step Use as a TCP client In this mode the FLITE395 initiates the TCP connection on alarm events and sends unsolicited messages The TCP connection is not maintained except if the SCADA sends application message periodically In this mode is not necessary to maintain the TCP connection On each alarm the equipment will establish the connection to provide the events The Keep Alive timeout should be chosen at 1 minute for this mode The SCADA must do some automatic request depending IIN status When IIN indicates that a synchronization is needed
10. MV electrical network management Easergy range FLITE 395 GPRS DNP3 MV substation remote monitoring Directional DNP 3 0 communication Appendix to the User Manual Schneider Electric FLITE395 GPRS DNP 3 0 00191 01 EIU 3 5 27 4 GENER 6 SOFTWARE 7 DNPS PROTOGOE EATURE 5 iiec 8 MAIN SUMI HP 9 ALARM 65 1 1 10 GPRS PARAMETERS 2220 11 DNP9S PARAMETERS 2020 Doe ee te 13 EQUIPMENT STATE tee t d areae 14 DNPGS ANADYSER iiec coo a eere eoe teet ee cue rete 15 DISPLAY EVENT ero eerte terere petet ere 16 SOLAR VERSION 17 INTRODUGTION 20 17 CLIENT MODE SETTINGS 41 17 TCP SERVER MODE SETTINGS eee 20 SPECIAL 27 Schneider Electric 3 FLITE395 GPRS DNP 3 0 Overview Commissioning Before the first use the following steps have Connect the red to Connect the black to be followed the positiv
11. S IP address 192 168 1 1 Remote port 20000 Escape Exit KeepAlive timeout in TCP client mode corresponds to the max TCP connection time As the TCP connection is not maintained the max duration must be below 1 minute NT00191 EN 01 Schneider 18 FLITE395 GPRS DNP 3 0 MERLIN GERIN Configuration Diagnostic ALT F4 Exit GPRS Parameters SIM CARD PARAMETERS PIN code 0000 GPRS COMMUNICATION PARAMETERS APN Server Max 30 Digits APN Login Max 30 Digits APN Password Max 30 Digits Time between connection attempt 1 Specific Ping IP Address So 2822206 1 3 Test Ping time ih Ping delay s i od Ping number 23 Daily disconnect 0 hO min Escape Exit If GPRS network is not available for a long period of time the equipment must not waste too much of energy by trying to connect to it 1 hour permits to limit the impact on solar panel sizing For the ping period a period of 1 hour limits the energy budget to 2 minutes 00191 01 Schneider 19 FLITE395 GPRS DNP 3 0 TCP server mode settings If the SCADA system is not compliant with DNP3 TCP client slave FLITE395 can be used as TCP server with the following settings MERLIN GERIN Configuration and Diagnostic ALT F4 Exit Alarm Parameters Alarm message enabled No Digital input 1 yes Alarm test no Digital input 2 yes Cyclic dial up
12. T REQUEST RESPONSE Notes slave must parse master must parse Obj Var Description Func Qual Func Qual Codes Codes Codes Codes dec hex dec hex 1 0 Binary Input All Variations 1 06 1 1 Binary Input 129 00 1 2 Binary Input with Status 129 00 2 2 Binary Input Change with Time 129 17 Echo of 12 1 Control Relay Ouput Block 5 6 17 28 129 request 20 0 Binary Counter All Variations 1 06 20 1 32 Bit Binary Counter 129 00 50 1 Time and Date 2 see 07 where 4 14 quantity 1 60 1 Class 0 Data 1 06 60 2 Class Data 1 06 07 08 60 3 Class 2 Data 1 06 07 08 di 60 4 Class3 Data 1 06 07 08 di 80 1 Internal Indications 2 00 index 7 No object 13 No object 23 see 4 14 Addition to Highest DNP Levels Supported 7 RESPONSE TO THIS REQUEST IS OBJECT UNKNOWN NT00191 EN 01 Schneider 25 P Electric FLITE395 GPRS DNP 3 0 Description Index Default Static Variation Default Event Variation Point Name hex dec Obj Var Desc Obj Var Class Desc Control Relay 0 0 12 1 Digital Output 1 Ouput Block Control Relay 1 1 12 1 Digital Output 2 Ouput Block Control relay output block 0 and 1 Command of digital output 1 and 2 Description Index Default Static Default Event Variation Point Name hex dec Variation Obj Var Desc Obj Var Class Desc Binary Input 0 0 1 1 No Status 2 2 1 With Time Di
13. e wire to the negative connector connector First step Place and connect the battery in the box of the solar panel Second step Remove the cover to access the communication card 00191 01 Schneider 4 FLITE395 GPRS DNP 3 0 Overview Third step Put the SIM card in the modem Plug the solar panel cable in the hole Pull the cable within the box in order to connect the connector and the green wire Plug the little connector Power supply with two wires in the corresponding connector Plug the green wire in the other connector in the fourth hole just near the other wire Connect the antenna Connect the antenna Press the release button and put the SIM card in the holder Plug the solar panel cable here Plug the connector with 2 Nota the LED on the modem blinks when wire in this one the network connection is established Plug the green wire in the fourth hole WARNING Before putting the SIM card Don t touch the contacts with the fingers Clean the contacts with a cleanser and lubricant deoxidiser very high protection For example Cleaner Jeltonet Plus Fourth step Replace the cover Proceed the setting and placing into service with the user manuel NT00047 01 Directory Documentation on CD Rom 00191 01 Schneider 5 FLITE395 GPRS DNP 3 0 00191 01 Software Configuration General Local configuration Configuration and diagnosis o
14. f the FLITE395 are performed by connecting a laptop PC This software can be used to Change the FLITE395 configuration communication parameters alarms etc Read the equipment state of the FLITE395 Read the recordings made by the FLITE395 Reset the time of the 95 Requisite equipment The equipment is configured using a PC provided with MS DOS n FLITE395 Configuration and diagnostic software Connection cable provided Running the configuration program Connect the cable to serial port 1 COM1 of the computer and to the external connector of FLITE395 Start the PC under Windows and insert the CD Rom Select and open MG exe program in the FLITES95 Cfgeaser directory The configuration program is running The main menu appears Comments concerning the use of the software Following modifications the configuration data are only acknowledged by the equipment after validation in the OK zone n During modifications and before the validation operation the equipment runs with the previous data which are therefore at least partially different from the data currently displayed on the Screen Action in the Cancel zone displays the old parameters again The zone in which the cursor is positioned is highlighted To move between zones data input fields or function title the arrow keys or tabulation key are used To select a highlighted zone the Enter o
15. gital Input 1 Binary Input 1 1 1 1 No Status 2 2 1 With Time Digital Input 2 Binary Input 2 2 1 1 No Status 2 2 1 With Time Digital Input 3 Binary Input 3 3 1 1 No Status 2 2 1 With Time Digital Input 4 Binary Input 4 4 1 1 No Status 2 2 1 With Time Digital Input 5 Binary Input 5 5 1 1 No Status 2 2 1 With Time Digital Input 6 Binary Input 6 6 1 1 No Status 2 2 1 With Time Digital Output 1 state Binary Input 7 7 1 1 No Status 2 2 1 With Time Digital Output 2 state Binary Input 8 8 1 1 No Status 2 2 1 With Time Toogle Bit on cyclic alarm Binary Input 9 9 1 1 No Status 2 2 1 With Time Stack 80 Binary Input A 10 1 1 No Status 2 2 1 With Time Reserved Binary Input B 11 1 1 No Status 2 2 1 With Time Reserved Binary Input 12 1 1 No Status 2 2 1 With Time Reserved Binary Input D 13 1 1 No Status 2 2 1 With Time Reserved Binary Input 14 1 1 No Status 2 2 1 With Time Reserved Binary Input 15 1 1__ No Status 2 2 1 With Time Reserved NT00191 EN 01 Schneider 26 FLITE395 GPRS DNP 3 0 Special considerations Internal Indications Control center time synchronization Bit 4 of first IIN byte is set when FLITE395 starts up This bit is cleared when the SCADA sends its first clock synchronization message Then FLITE395 sets it again regularly every hour to ensure the SCADA is answering it on a regular basis This clock synchr
16. neider Electric 13 FLITE395 GPRS DNP 3 0 Equipment State The equipment states menu is used to display the information linked to the state of the FLITE395 Equipment States Current states are indicated in reverse video Digital Outputs Use the 5 select confirm and A cAncel keys to control the relay outputs The state of the relay is also indicated in 2 tss Digital Output 1 state and Digital Output 2 state see p25 Their value is 0 when they are open and 1 when they are closed Digital Inputs Inputs in logical state 1 are indicated in reverse video Modem not identified FLITE395 was unable to communicate with the modem used SIM card failure FLITE395 has detected the embedded GSM modem card but cannot read the SIM card address Indicates the current IP address of the FLITE395 GSM signal quality Specific to the GSM modem the bar chart indicates the quality of the reception signal NT00191 EN 01 Equipment state Flair 200C fault Config fault Alarm processing Communication state Modem not identified SIM card failure GSM signal quality Modem state TCP Listened DI 1 The signal must be between 17 and 31 MERLIN GERIN Configuration and Diagnostic ALT F4 Exit Equipment state Digital outputs DO Controle Select Confirm command cAncel command Digital inputs Ip address DI 2 80 10 61 197 DI 3 DI 4
17. no yes Cyclic dial up no yes Starting time min 0 yes hour 0 Digital input yes Period hours 24 Digital input t yes Stack overflow B yes Escape Exit Cyclic dial up e The yes option causes cyclic dial up to the control station e Default value is Note In client mode the Cyclic Dial up has to be activated so the SCADA know that the FLITE395 is alive A L To validate the change of starting time the Cyclic dial up alarm has to be deactivated and activated again Starting time min amp hour e Starting time in the following 24 hours of the cyclic dial up e Default value is midnight Period e Time interval between two consecutive cyclic dial ups from 0 to 255h Default value is 24 hours Note Each dial up causes the change of the tss Toogle Bit on cyclic alarm see p25 Mtis recommended to keep a period of 24hours Schneider 10 FLITE395 GPRS DNP 3 0 GPRS Parameters PIN code Setting of the PIN code into the SIM card default value is 0000 In case of wrong PIN code SIM card failure appears in the screen Equipment states Important after three incorrect attempts the SIM card becomes invalid To make it valid a mobile phone must be used The FLITE395 cannot do this Please consult the user guide of the SIM Card to return to an available status MERLIN GERIN Configuration and Diagnostic ALT F4 Exit GPRS
18. o E recognised with some complementary M E 05 64 0 44 0 1 10 F information such as the direction of the frame E2 C4 81 00 02 5A 06 Host gt FLITE395 or FLITE395 gt Host di possibly the error detected character 06 29 72 gt gt 03 6d OA da 02 00 DI EL framing error overflow checksum bad E AE 05 64 14 C4 01 00 02 00 4A A2 length bad control character In case of ee 2 2 77 2 i it 1 i E4 C6 81 00 02 01 01 00 00 OF 10 00 AD D6 multiple errors it s the first one that is 06 34 77 ce stie x 05 64 14 C4 01 00 02 00 4A A2 indicated D5 C7 01 3C 02 06 3C 03 06 3C 04 06 3C 01 06 B4 71 Each correct frame is shown one block per 7 7 7o OF DI DO OQ arb ob eared 90 cix 05 64 OE C4 01 00 02 00 EO 66 line 10 bytes for the first 18 bytes for B d E pe Ru o M next ones last one be shorter 06 36 91 gt gt 05 64 11 44 02 00 01 00 5D 81 t last y be shorter E6 C8 81 00 02 01 01 00 00 OF 10 00 4E 81 00191 01 Schneider 15 Electric FLITE395 GPRS DNP 3 0 Display events This menu displays the events with the date of occurrence The existing events are the following Digital Input 1 Off Digital Input 1 On Digital Input 2 Off Digital Input 2 On Digital Input 3 Off Digital Input 3 On Digital Input 4 Off Digital Input 4 On
19. o it 1 hour permits to limit the impact on solar panel sizing For the ping period a period of 1 hour limits the energy budget to 2 minutes 00191 01 Schneider 21 FLITE395 GPRS DNP 3 0 Device Profile Document DNP V3 00 DEVICE PROFILE DOCUMENT Vendor Name SCHNEIDER ELECTRIC Device Name F2DGPL C DNP3 V1 00 Highest DNP Level Supported Device Function For Requests LI Master Slave For Responses L1 Notable objects functions and or qualifiers supported in addition to the Highest DNP Levels Supported the complete list is described in the attached table e Binary input All Variations Read all points e Binary output Variations Read all points Maximum Data Link Frame Size octets Maximum Application Fragment Size octets Transmitted 292 Transmitted 1369 Received 498 Received must be 292 Maximum Data Link Re tries Maximum Application Layer Re tries None None Fixed at Fixed at Configurable range 1 to 10 Configurable range 1 to 10 9 Enables an application fragment to contain all class 0 data including expansion future use and reserved points and 100 event objects corresponding to event buffer capacity Local configuration with a PC 00191 01 Schneider 22 FLITE395 GPRS DNP 3 0 Requires Data Link Layer Confirmation Never Always Sometime
20. odem is TCP connected to the SCADA See modem stat on equipment state menu Ping time Frequency of the ping request Default value is 1h Ping delay s Waiting time of the answer to ping request Default value is 5s Ping number Number of ping request Default value is 3 If the pings fails it means that the FLITE395 is not connected to the GPRS network so the modem is reseted Mtis recommended to choose 3 pings every hour Schneider NT00191 EN 01 P Electric 11 FLITE395 GPRS DNP 3 0 GPRS version only TCP IP Parameters Local Port e Enter the port number you want FLITE395 to listen to incoming TCP connection Value is from 1 to 65535 e Default value is 20000 Keepalive timeout e In client mode Maximum duration of a TCP IP connection On time out expiry the TCP IP connection is closed Each time the FLITE395 receives a request the timer is re armed e server mode Maximum duration of a TCP IP connection after the reception of a SCADA request Each time the FLITE395 receives a request the timer is re armed It is recommended to choose a longer time about 1 hour If the FLITE395 is used as a client keepalive timout has to be chosen equal to 1 min so the FLITE395 can send all this data to the SCADA If the FLITE395 is used as a server the keepalive has to be chosen long enough It is recommended to choose a longer time 1hour and 1min 00191
21. onfirm e Select yes if you want User Data to be sent using a SEND CONFIRM expected frame type by the Link Layer Selecting no configures Link Layer to use a SEND NO REPLY expected frame type for User Data transmission Notice that in the case where SEND NO REPLY expected frame type is used FLITE395 will never send RESET of remote link frames It will work strictly as a slave e Default is yes Maximum Data Link Re tries e Defines the number of re tries by the Link Layer when the RTU doesn t receive any CONFIRM frame ACK or to a frame using a SEND CONFIRM expected frame type When the Maximum Data Link Re tries is reached without confirmation Link Layer will perform RESET of remote link to re initialise the link e Default value is 3 Time out e It s the delay Link Layer will wait for a CONFIRM frame after sending a SEND CONFIRM expected frame Values are from 1 to 10s Default value is 5 s Delay before emission e To avoid collision when spontaneously emitting on a half duplex link FLITE395 will wait a T delay after seeing the link is no more busy using CD If at this moment CD is still not present FLITE395 will send the message If present it will wait another T delay T delay is the sum of Delay before emission and a random value Configured values are from 0 to 10 s e Default value is 1s e This time must be beyond keepalive timeou
22. onization is required to ensure a proper accuracy of time stamping process Should FLITE395 not receive a new synchronization message from the master within an hour after the last one the IIN bit is set 00191 01 Schneider 27 FLITE395 GPRS DNP 3 0 1 Digital input Red Fault is connected to Digital input 1 so when Digital input 1 equal 1 it means that a Red Fault is present Homopolar fault Green Fault is connected to Digital input 2 so when Digital input 2 equal 1 it means that a Green Fault is present Homopolar fault When Digital input 1 and Digital input 2 are both equal to 1 it means that there is a polyphase fault On solar version only Digital input 3 is connected to the battery fault So when Digital Input 3 equal 1 it means that there is a battery fault NT00191 EN 01 Schneider 28 FLITE395 GPRS DNP 3 0 Annexe 2 GPRS network characteristics IP network Private network or VPN internet Firewall Permanent Link to IP network ADSL or Lease Line or others Allows incoming and outcoming connection on port 20000 GPRS SIM CARD with the following access an open port for DNP3 communication 20000 on both direction Ip address for RTU Static IP and Private IP NT00191 EN 01 Schneider 29 FLITE395 GPRS DNP 3 0 Schneider Electric Industries SAS Schneider Electric Telecontrol 839 chemin des Batterses
23. provider often disconnects equipments on network that does not transmit during a period of time or disconnect equipment after a fixed duration This interval can sometimes be configured by provider To avoid waste of energy due to provider disconnection a maximum of 2 disconnections a day is recommended We recommend having an energy budget of 5 minutes for IP connection and disconnection 2 minutes for IP monitoring minutes for Protocol transmission TCP client mode settings For solar version we recommend to use the equipment as a TCP client with the following settings MERLIN GERIN Configuration and Diagnostic ALT F4 Exit Alarm message Digital input Digital input Digital input Digital input Digital input Digital input Stack overflow Escape Exit Alarm Parameters enabled yes OY I9 HS yes Alarm test yes Cyclic dial up yes Starting time min yes hour Yes Period hours yes yes no yes 12 24 Alarm message must be enabled and a daily connection must be configured to check the equipment status 00191 01 Schneider 17 FLITE395 GPRS DNP 3 0 DNP3 TCP IP parameters MERLIN GERIN Configuration and Diagnostic ALT F4 Exit F2DGPL PARAMETERS Local port 20000 Keepalive timeout 1mn connect delay lst try 15 Os random value 2nd try 1 3rd try 2mn SCADA PARAMETER
24. r Space keys used Schneider 6 Electric FLITE395 GPRS DNP 3 0 00191 01 Software Configuration Parameter values are modified using n the or Space keys to increase the value n the key to reduce the value When a parameter value is at its maximum pressing the or Space key changes the value to its minimum Pressing the key changes it back to the maximum To exit a sub menu the user presses the Escape key To exit the main menu the user presses the Alt and F4 keys simultaneously Specific messages When the configuration software is started up several types of message may appear on the screen Unidentified Equipment connected the serial link between the configuration computer and the equipment to be configured is not valid check the connection cord and the connection location at the computer end Fault messages related to a configuration loss or internal problem Software configuration Pressing the F10 key accesses the software configuration menu The menu is used to modify display colors m the serial port used SCADA The SCADA has to be connected to internet and its IP address must be known for the configuration of the FLITE395 Schneider 7 Electric FLITE395 GPRS DNP 3 0 DNP3 Protocol Feature Introduction DNP3 TCP protocol is implemented for GPRS communication Only TCP connections are accepted UDP is not implemented FL
25. s Configurable Requires Application Layer Confirmation Never O Always not recommended L1 When reporting Event Data Slave devices only When sending multi fragment responses Slave devices only Sometimes If Sometimes when Configurable Timeouts while waiting for Data Link Confirm O None Fixed at Variable M Configurable Complete Appl Fragment None Fixed at Variable Configurable Application Confirm O None Fixed at Variable Configurable Complete Appl Response None Fixed at Variable Configurable Others Sends Executes Control Operations WRITE Binary Outputs Never O Always Sometimes Configurable SELECT OPERATE MNever O Always O Sometimes Configurable DIRECT OPERATE O Never Always O Sometimes Configurable DIRECT OPERATE NO ACK Always O Sometimes Configurable Count gt 1 Never O Always O Sometimes Configurable Pulse On MNever O Always O Sometimes Configurable Pulse Off MNever O Always O Sometimes Configurable Latch On Always O Sometimes Configurable Latch Off O Never Always O Sometimes Configurable Queue Never Always Sometimes Configurable Clear Queue Never O Always Sometimes Configurable Local configuration with a PC Executes as it has been received Always executes a Pulse On with on time
26. s DNP3 TCP IP parameters Modem Type GPRS GPRS Parameters SAVE CONFIGURATION OK Cancel DIAGNOSIS Display events Equipment state Erase events DNP3 Analyser Alarm Parameters Displays the alarm configuration screen DNP3 Analyser Displays the trace of exchanges between the equipment and the control station and the AT traces Display events Displays the events A maximum of 150 events are memorized The existing events are given in this document Erase events Select yes to erase the events Schneider FLITE395 GPRS DNP 3 0 Alarm Parameters Digital Input e For each Digital Input the yes option causes sending of an alarm on each change of state of the input e Default value is no Stack overflow e The yes option causes sending of an alarm upon occurrence of a stack overflow e Default value is yes Alarm message enabled e yes option activates alarm transmission e Default value is no A In client mode it must be set to yes Alarm test e yes option allows a test to be performed on alarm transmission to the control station The FLITE395 is calling the supervisor after recording of the configuration e Default value is no NT00191 EN 01 MERLIN GERIN Configuration and Diagnostic ALT F4 Exit Alarm Parameters Alarm message enabled no Digital input Digital input Digital input Digital input yes Alarm test
27. t 00191 01 MERLIN GERIN Configuration and Diagnostic ALT F4 Exit DNP3 Parameters LINK LAYER Idle line delay Requires Data Link Confirm Maximum Data Link Re tries 2 3 Time out Delay before emission APPLICATION LAYER Handle requested object s Sends Unsolicited Responses Wait delay Requires Application Confirm Maximum Application Re tries so Time out unknown bit Escape Exit Handle requested object s unknown bit If a requested object is unknown it will be indicated in the IIN byte Default value is yes Send Unsolicited Responses e Select yes if you want the FLITE395 to send the change of states of the DI or defaults to the SCADA without any request of the SCADA e Default value is no Mtis recommended to choose yes in client mode and in server mode too so the SCADA does not need to send requests every seconds to know the state of FLITE395 in real time Wait delay e Minimum delay between 2 concatenated messages e Default value is 100ms Requires application confirm e Select yes if you want the class 1 objects and unsolicited responses to ask for a confirmation request e Default value is no Maximum Application Re tries e Maximum number of confirmation request sent if no confirmation is received e Default value is 3 Time out e Maximum time to wait before sending a new confirmation request e Default value is 1min Sch
Download Pdf Manuals
Related Search