700iaTM Inversion Table Assembly Instructions
Contents
1. __TEETp an ups 700ia Inversion Table Assembly Instructions Inversion Table images may vary slightly from your model BEFORE YOU BEGIN Review all steps before beginning assembly and read all precautions before using the inversion table Carefully adhere to the Assembly Instructions and Owner s Manual to help ensure safety and product integrity IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING THE INVERSION TABLE A WARNING WARNING To reduce the risk of injury to persons Read and understand all the instructions view the instructional video review all other accompanying documents and inspect the equipment before using the inversion table It is your responsibility to familiarize yourself with the proper use of this equipment and the inherent risks of inversion such as falling on your head or neck pinching entrapment or equipment failure It is the responsibility of the owner to ensure that all users of the product are fully informed about the proper use of the equipment and all safety precautions Close supervision is necessary when the inversion table is used near children or by or near invalids or disabled persons Use the inversion table only for its intended use as described in this manual DO NOT use attachments not recommended by the manufacturer NEVER drop or insert any object into any opening DO NOT use or store product outdoors DO NOT use if you are over 6 ft 6 in 198 cm or over 3002. Attach the Owner s Manual MEEEEN The Owner s Manual contains important information on how to use your Teeter Hang Ups Inversion Table including how to personalize the user settings properly secure and release the Ankle Lock System and test and adjust the rotation control e If not already attached thread the provided metal chain through the pre punched hole in the upper corner of the Owner s Manual e Secure the chain to the A Frame through the designated hole in the Hinge Plate Figure 25 amp 25a Allow the Owner s Manual to hang freely on the outside of the A Frame Spreader Arms so it doesn t interfere with the rotation of the Table Bed IMPORTANT Once attached to the A Frame do not remove the Owner s Manual It should remain permanently attached to your inversion table to serve as a reference for all users in regards to proper adjustment and use of the equipment AWARNING Read the Owner s Manual thoroughly before using your Teeter Hang Ups Inversion Table Improper settings could result in serious injury or death Register Your Product e Please complete the warranty registration online at teeter inversion com H 220000000000000 19 CONNECT WITH US You f G facebook com teeterhangups teeter inversion com blog twitter com teeterhangups youtube com teetertv If you have any trouble assembling the equipment or questions about its use please contact customer service USA 800 847 0143 or info
3. replace defective components immediately and or keep the equipment out of use until repair FAILURE TO FOLLOW INSTRUCTIONS AND WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH SAVE THESE INSTRUCTIONS ITEMS FOR ASSEMBLY Page 1 of 2 ITEMS FOR ASSEMBLY ITEM NUMBER Base Assembly A Frame with pre assembled Stability Feet Angle Tether Head Pillow Decompression Arch NX1105 F51007 EP1105 IA1650 FitFlex Table Bed Upper Portion with pre assembled Bed Frame Extension A1310A Lower Portion with pre assembled Bed Frame F11300B Bolts 2 short 1 long amp Nuts 3 F11390 Main Shaft with Ankle Lock System I A1600 Front Ankle Bar Assembly Front Ankle Bar with pre assembled Foam Rollers Bolt Nut End Cap F51045 F51089 H13009 F51048 ITEMS FOR ASSEMBLY Handle Assembly Traction Support Handles 2 Bolts 2 Nuts 2 Hinge Cover Assembly Hinge Covers 2 Allen Head Screws 4 3 Hole Roller Hinges 2 TOOLS PROVIDED FOR ASSEMBLY 5mm Allen Wrench Screwdriver 10 13mm Wrenches 2 Packaged with the Roller Hinges ITEM NUMBER IA1670 F51085 H13009 F11250 F50075 F51064 ITEM NUMBER I1A1149 F51088 ITEMS FOR ASSEMBLY Page 2 of 2 Items not shown to scale Base Assembly Main Shaft with Ankle Lock System Handle Assembly F51007 O SONG 1A1670 H13009 SOs SR Hinge Cover Assembly EP1105 245 gp Ji P ee A EF f i B if if a O FF OL sy V 4 F 11250 50075 3 Ho
4. teeter inversion com International 1 242 362 1001 or info inversioninternational com USA Teeter 9902 162 St Ct E Puyallup WA 98375 Toll Free Phone 800 847 0143 Fax 800 847 0188 info teeter inversion com www teeter inversion com AT INternational Inversion International Ltd U Underwriters Laboratories Inc PO Box AP 59245 Deakin Salas a ae New Providence Island Bahamas proauct nave been evaluate 3 z C L US ETDE Phone 1 242 362 1001 Medical Device Safety Service GmbH safety standards Schiffgraben 41 Fax 1 242 362 1002 30175 Hannover oo CS info InversionInternational com Germany Any modification to this device will void the UL Listing www InversionInternational com Tel 49 511 62628630 U S and Foreign Patents Pending Teeter Hang Ups is a registered trademark of Teeter Specifications subject to change without notice COPYRIGHT 2013 Teeter International Law Prohibits Any Copying LI7001 0713 0
5. unlock Figure 7 e In your other hand hold one 3 Hole Roller Hinge at the Pivot Pin With the Pivot Pin facing out away from the Table Bed slide the bottom of the Roller Hinge between the Cam Lock and the Bracket TIP Make sure that the Cam Lock is completely open when inserting the Roller Hinge otherwise assembly will be more difficult e Engage one of the holes in the Roller Hinge over the Bracket Pin Figure 9 shows the Roller Hinge installed correctly with the Bracket Pin engaged in Setting C NOTE Refer to the Owner s Manual for an explanation of the hole settings If you are unsure use Setting C to start e Push down on the Cam Lock Figure 8 to lock it and secure the Roller Hinge 0 G e Repeat on other side Make sure the Roller Hinges are in the same hole setting 1 Bracket Pin on both sides 10 STEP Attach the Table Bed to the A Frame e Face the front of the A Frame where the Crossbar is located refer to Figure 4 to determine A Frame Front e Grasp both the Roller Hinges right above the Cam Lock and lift the Table Bed Allow the top of the Table Bed to rotate toward the floor so that the back of the Table Bed is now facing you and the top of the Table Bed is in front of the Crossbar Figure 10 e Lower each Roller Hinge Pivot Pin into the A Frame hinge plates one side at a time Figure 11 The Self Locking Hooks will open to allow the Pivot Pin into the Hinge P
6. use Setting A for users over 220 Ibs 100 kgs REPLACE LABEL IF DAMAGED ILLEGIBLE OR REMOVED E6 1740 0711 0 TIPPING HAZARD For upright storage leave A Frame open wide enough to remain stable or secure to the wall to prevent tipping In households with small children the table should be stored flat on the floor not upright REPLACE LABEL IF DAMAGED ILLEGIBLE OR REMOVED NX 1720 0910 2 WARNING To reduce the risk of personal injury or death Read and understand all the instructions before using the inversion table It is your responsibility to familiarize yourself with the proper use of the equipment and the inherent risks of inversion such as falling on your head or neck pinching entrapment or equipment failure e Do not allow children to use the machine e Keep children bystanders and pets away from the machine while in use e Keep body parts hair loose clothing and jewelry clear of all moving parts e Height Weight capacity 4 ft 8 in 6 ft 6 in 142 198 cm 300 Ibs 136 kgs e This product is for consumer indoor household use only Replace Labels and Owner s Manual if Damaged Illegible or Removed Teeter 9902 162nd St Ct E Puyallup WA 98375 Toll Free Phone 800 847 0143 Web www teeter inversion com ep 1737 0911 3 Ankles must be properly secured before use REPLACE LABEL IF DAMAGED ILLEGIBLE OR REMOVED BEFORE BEGINNING ASSEMBLY Unpack and Prepare Your Workspace e If pos
7. Ibs 136 kg Structural failure could occur or head neck may impact the floor during inversion DO NOT allow children to use this machine Keep children bystanders and pets away from machine while in use Keep body parts hair loose clothing and jewelry clear of all moving parts The inversion table has no user serviceable parts This product is intended for indoor home use only DO NOT use in any commercial rental or institutional setting FAILURE TO FOLLOW INSTRUCTIONS AND WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH SAVE THESE INSTRUCTIONS BEFORE YOU BEGIN Review all steps before beginning assembly and read all precautions before using the inversion table Carefully adhere to the Assembly Instructions and Owner s Manual to help ensure safety and product integrity IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING THE INVERSION TABLE A WARNING DO NOT use the equipment without a licensed physician s approval and a review of the medical contraindications as noted in the Owner s Manual Failure to assemble and or use the equipment as directed may void the manufacturer s warranty on this product and could result in injury or death Choose a level surface for assembling and operating the table Follow each step in sequence DO NOT skip ahead Make sure that all fasteners are secure ALWAYS test and inspect the table Make sure the table rotates smoothly to inverted position and back ALWAYS
8. ft Figure 15 From the back side of the Front Ankle Bar housing pull the plastic zip tie to stretch the Retainer Spring and Cable Loops so that they align with the bolt holes in the back of the Front Ankle Bar housing e Insert the Bolt through the hole in the outer side of the housing through both the Retainer Spring and Cable Loops and through the hole in the other side of the housing Figure 15a AWARNING Failure to assemble the T Pin Ankle Lock System properly could result in serious injury or death STEP 5 Front Ankle Bar Assembly to the Main Shaft CONTINUED e Release your hold on the plastic zip tie Secure the Bolt with the Nut Figure 16 using the 10 13mm Open Ended Wrench provided IMPORTANT Cut the long segment of zip tie off so that it will not interfere with the function of the Retainer Spring Be careful not to damage the Retainer Spring with the Cable e Cover the open end with the End Cap Figure16a You may need to use a rubber mallet to asist with securing the End Cap AWARNING Failure to assemble the T Pin Ankle Lock System properly could result in serious injury or death 13 FIGURE 18 STEP Assemble the Main Shaft to the Table Bed e Facing the front of the A Frame hold the Main Shaft in your left hand with the height markings facing up e Slide the end of the Main Shaft into the Main Shaft Housing Figure 17 located at the base of the Table Bed e Wi
9. late slot then automatically snap closed over the Pivot Pin TIP You may need to push outward on the Hinge Plate in order for the second Pivot Pin to lock in place e Make sure that each Pivot Pin is seated at the base of the slot in the Hinge Plates and that the Self Locking Hooks have closed over both Pivot Pins Figures 12a amp 12b FIGURE 12a FIGURE 12b TOP VIEW ia INSIDE VIEW AWARNING Failure of the Self Locking Hooks to close over both Roller Hinge Pivot Pins is an indication of improper assembly and if not corrected could result in serious injury or death 11 STEP 5 Front Ankle Bar Assembly to the Main Shaft FIGURE 14 1 Front Ankle Bar Housing 1 Retainer Spring amp Cable Loop 2 Temporary Zip Tie NOTE Extending out from the Front Ankle Bar you will see a temporary plastic zip tie fastened to the loops of the Retainer Spring with Cable This is provided to assist with the assembly process detailed below e With hole settings of the Front Ankle Bar facing up insert the temporary plastic Zip tie and Front Ankle Bar into the Front Ankle Bar housing Figure 14 of the Main Shaft e Pull up on the T Pin Lock to allow the Front Ankle Bar to insert all the way into the housing Release the T Pin to engage in the hole setting closest to the bar Figure 14a Large Arrow Pull up on the T Pin Small Arrow Insert the Front Ankle Bar into the Front Anke Bar Housing e Turn over the Main Sha
10. le Roller Hinges YA N Ses eeee nini F51064 F51089 Tools for Assembly e C E 113008 gt LNN SIU IA1149 g P OG O F51048 F51088 AQ caw TI AN 0 auc OO UNDERSTANDING YOUR INVERSION TABLE Before reading further study the drawing below to familiarize yourself with the important components of your new Teeter Hang Ups Inversion Table Identifying Parts and Components 2 Located on back of table 1 Head Pillow 10 Spreader Arms 2 Bed Frame Extension 11 Angle Tether 3 FitFlex Table Bed 12 Crossbar 4 Self Locking Hooks 13 A Frame 5 Hinge Plates 14 Main Shaft 6 Pivot Pins 15 Ankle Lock System 7 3 Hole Roller Hinges 16 Ankle Comfort Dial 8 Handles 17 Stability Feet 9 Height Selector Locking Pin Inversion Table images may vary slightly from your model WARNING LABEL PLACEMENT DIAGRAM Important Please review all labels and supporting materials before using your inversion table This drawing indicates the locations of the warning labels found on your product If a label is missing illegible or is removed contact Customer Service at the phone number or website found on the last page to request a complimentary replacement label Note Image and labels below not shown at actual size Do not
11. sible set up the product at or near the space in which you intend to use it to avoid moving it later e Unpack all parts and support materials Set aside packing materials and clear your work area e Locate the Small Parts Bags packaged with the manuals They are labeled to correspond with the assembly process STEP 1 Assemble the Table Bed FIGURE 1 Lower Hole Longer Bolt Upper Holes Shorter Bolts i FIGURE3 e i i FIGURE 3a i tes 2 SAS lt z lt s Tie 3 leg AR 1 Bolt 2 Loop NOTE This assembly will be referred to as Table Bed for the remainder of the Assembly Instructions e Locate the following items to assemble the FitFlex Table Bed Table Bed Upper Portion with pre assembled Bed Frame Extension Table Bed Lower Portion with pre assembled Bed Frame Hardware Table Bed Assembly Hardware Bag 3 Bolts amp 3 Nuts Tools 5mm Allen Wrench amp 10 13mm Open Ended Wrenches e Lay the Upper and Lower Portions face down on the floor Figure 1 e Lift the pre assembled Bed Frame Extension and slide the Lower Portion amp Frame to seat it on top of the Upper Portion aligning the bolt holes Figure 2 Release the Bed Frame Extension so that it rests on top of the two upper holes e Reaching underneath insert one of the shorter bolts through an upper hole in the Upper Portion and Bed Frame Extension Loop Hand tighten with a nut Figure 3 amp 3a e Repeat with remaining
12. side e Reaching underneath insert the longest bolt into the lower hole and hand tighten with a nut e To fully tighten all three nuts to the bolts insert the 5mm Allen Wrench into the Bolt heads and tighten the Nuts using the 10 13mm Wrench STEP 2 Open the A Frame FIGURE 4 1 Spreader Arms 2 Crossbar e On a level surface position the A Frame so that it is standing upright and the Stability Feet are on the ground e Gently push down on the Spreader Arms to ensure they are fully open and in the locked position Figure 4 e Look for these temporary labels on your A Frame designed to assist you with the remainder of the assembly process You may choose to remove them after you assembled your inversion table RIGHT Indicates right side as you are using the inversion table not facing it LEFT ndicates left side as you are using the inversion table not facing it BACK Indicates the back of the A Frame fully assembled inversion table FRONT ndicates the front of the A Frame fully assembled inversion table STEP 3 Assemble the Roller Hinges to the Table Bed e Familiarize yourself with the terms detailed below in Figure 5 AWARNING NEVER disassemble the Roller Hinge Pivot Pin FIGURE 5 Bracket Pin e For ease of assembly rest the Table Bed against the Crossbar Figure 6 at the front FIGURE 8 of the A Frame C e On one side of the Table Bed lift the Cam Lock up all the way to
13. th your right hand pull out the Height Selector Locking Pin Figure 17a to allow the Main Shaft to slide in further and release in the desired height setting NOTE Refer to the Owner s Manual for more information on selecting your height setting e The Main Shaft MUST REST against the Crossbar of the A Frame Figure 18 IMPORTANT The Crossbar prevents the Table Bed from rotating forward when the user steps on the Ankle Comfort Dial If the Main Shaft does not rest on the Crossbar as shown in Figure 18 then the Table Bed has been assembled backwards onto the A Frame This MUST BE CORRECTED before use e Test the inversion table by hand for smooth and steady rotation Figure 19 and ensure that all fasteners are secure 14 MISASSEMBLY CHECK AWARNING If your Teeter Hang Ups Inversion Table looks like either of these images your inversion table has been misassembled and is unfit for use Improper assembly could result in serious injury or death Image A Go back to Step 3 for instruction Demonstrates that the Roller Hinges have been assembled upside down into the Table Bed and must be corrected Image B Go back to Step 4 for instruction Demonstrates that the Table Bed has been assembled into the A Frame backwards so the Main Shaft is not resting on the Crossbar and must be corrected O o CORES 228 S8 a GOT TIA 9 Za NE oo Qi Sea Inversion Table images may vary slightly from
14. your model 15 im 20 Pa STEP 7 Assemble the Handles to the A Frame e Insert the Left and Right handles into the A Frame Figure 20 so that the long part of the handles are parallel with the rear legs of the A Frame e Insert the Bolt from the inside through the Hinge Plate into the Handle Hand tighten with the nut on the outside of the Hinge Plate Figure 21 e Secure using the 10 13mm Open Ended Wrenches provided being careful not to overtighten e Repeat on the other side 16 STEP Assemble the Hinge Covers to the A Frame FIGURE 22 Q e Align the Left and Right Hinge Covers with the corresponding shape of the Hinge Plate on either side of the A Frame Figure 22 e Insert two 2 Allen Bolts through the Hinge Plate into the Hinge Cover e Tighten with the Allen Wrench provided being careful not to overtighten e Repeat on the other side 1 Hinge Cover 2 Allen Bolts 17 STEP Attach the Accessories FIGURE 23 Or VE Assemble the Angle Tether OPTIONAL l e The Tether will come pre assembled to the A Frame e Unfold the adjustable Tether and clip it to the U Bar on the underside of the Table Bed Figure 23 Attach the Head Pillow OPTIONAL e Attach the Head Pillow by inserting the Velcro Straps through the holes in the Table Bed and securing the ends together Figure 24 The position of the pillow can be adjusted depending on the user 18 BEFORE INVERTING FIGURE 25 pa
Download Pdf Manuals
Related Search