RouterBOARD 411AR Quick Setup Guide and Warranty Information
Contents
1. RouterBOARD 411AR Quick Setup Guide and Warranty Information 5 e O 600 One MMCX connector for bult in radio a Built in WiFi card PrrerrprannerpnperrteT t thi ri t it li I Ajaga ECEE depo ro HSC LE RARARRARARS a male Z B a f fe Q P fe fe c E 2 2 woovonpnnons Goes o ReReKERERERD baxan Emas jang inih amp O PI 3078 5 TE 7 Arper 7 EU is as Sit N Oy 4302 5 11h lay LED1 LED2 LED3 LED4 LEDS LED6 Sa Ssosm osm zoso coca iosa iF Yet es fos meer eS fe j Assembling the Hardware First use of the board e Insert the MiniPCI card RouterBOARD 411AR provides one MiniPCI slot on the top of the board e Connect antenna cables to the MiniPCI card and or to the built in WiFI card s MMCX connector e Install the board in a case and connect other peripherals and cables e Plug in power cable to turn on the board Powering The board accepts powering from either the power jack or the LAN1 Ethernet port e direct input power jack J7 5 5mm outside and 2mm inside diameter female pin positive plug accepts 9 28V DC overvoltage protection starts at 28V e LAN1 Ethernet port J8 accepts 9 28V DC input at the board higher voltage needed to compensate for power loss on long cables at least 18V suggested from non standard passive Power over Ethernet injectors no power over datalines The board does not work with IEEE802 3af co2. her errors No liability is assumed for any inaccuracy found in this publication nor for direct or indirect incidental consequential or other damages that may result from such an inaccuracy including but not limited to loss of data or profits Please report any inaccuracies found to support mikrotik com See www routerboard com for more information Contact support mikrotik com for support questions rev B 23 Apr 2010
3. kls SIA All trademarks and registered trademarks appearing in this manual are the property of their respective holders Hardware MikroTikls SIA warrants all RouterBOARD series equipment for the term of one year from the shipping date to be free of defects in materials and workmanship under normal use and service except in case of damage caused by mechanical electrical or other accidental or intended damages caused by improper use or due to wind rain fire or other acts of nature If you have purchased your product from a MikroTik Reseller please contact the Reseller company regarding all warranty and repair issues the following instructions apply ONLY if you purchased your equipment directly from MikroTik Latvia To return failed unit or units to MikroTikls you must perform the following RMA Return Material Authorization procedure Follow the instructions below to save time efforts avoid costs and improve the speed of the RMA process Take into account that all goods have one year warranty Instructions are located on our webpage here http rma mikrotik com Manual This manual is provided as is without a warranty of any kind expressed or implied including but not limited to the implied warranty of merchantability and fitness for a particular purpose The manufacturer has made every effort to ensure the accuracy of the contents of this manual however it is possible that it may contain technical inaccuracies typographical or ot
4. mpliant 48V power injectors The maximum output of the power supply available for extension cards is normally 10W 3 0A Booting process First RouterBOOT is started It displays some useful information on the onboard RS232C asynchronous serial port The serial port is set by default to 115200bit s 8 data bits 1 stop bit no parity Note that the device does not fully implement the hardware RTS CTS flow control so it is suggested to try to disable hardware flow control in the terminal emulation program in case the serial console does not work as expected and if it does not help make a new cable using the pinout given in the User s manual The loader may be configured to boot the system from the onboard NAND and or from network See the respective section of User s manual on how to configure booting sequence and other BIOS parameters http wiki mikrotik com wiki First_time_startup DHCP or BOOTP configurable in loader protocols allow the RouterBOARD 411AR device to get an initial IP address and provide the address of a TFTP server to download an ELF boot image from It is especially useful for software installation See the User s manual for more information and protocol details Note that you must connect the RouterBOARD you want to boot and the BOOTP DHCP and TFTP servers to the same broadcast domain i e there must not be any routers between them they must be on the same Ethernet switch See www routerboard com for more informatio
5. n Contact support mikrotik com for support questions rev B 23 Apr 2010 Extension Slots and Ports e One Ethernet port supporting automatic cross straight cable correction Auto MDI X so you can use either straight or cross over cables for connecting to other network devices The Ethernet port accepts 9 28 V DC powering from a passive PoE injector e One MiniPCI Type IIIA IIIB port with 3 3V power signaling e Built in 802 11b g WiFi card AR2417 with one MMCX connector to the left of it e DB9 RS232C asynchronous serial port Buttons and Jumpers ROS reset jumper hole RESET resets RouterOS software to defaults Must short circuit the metallic sides of the hole with a screwdriver for example and boot the device Hold screwdriver in place until RouterOS configuration is cleared RouterBOOT reset button S301 loads backup RouterBOOT Loader firmware Must hold button while booting Use in case operating system can t be booted and no useful information on Serial console output Operating System Support Currently tested operating system is MikroTik RouterOS starting from version 3 23 Copyright and Warranty Information Copyright and Trademarks Copyright MikroTikls SIA This manual contains information protected by copyright law No part of it may be reproduced or transmitted in any form without prior written permission from the copyright holder RouterBOARD RouterOS RouterBOOT and MikroTik are trademarks of MikroTi
Download Pdf Manuals
Related Search