Installation Manual - Air Marketing Group LLC
Contents
1. The connection procedure for the refrigerant pipe varies according to the exit position of the pipe when facing the wall Right A Left B Underside C Rear 1 Cut out the appropriate knock out piece on the rear of the indoor unit unless you connect the pipe directly from the rear 2 Smooth the cut edges 3 Remove the protection caps of the pipes and connect the assembly pipe to each pipe Tighten the nuts first with your hands and then with a torque wrench applying the following torque Outer Diameter Torque 1 4 inch 10 1 12 3 ft lb 3 8 inch 18 1 20 3 ft lb 1 2 inch 27 5 30 4 ft lb 5 8 inch 31 8 34 7 ft lb gt If you want to shorten or extend pipes refer to page 9 4 Cut off the remaining foam insulation 5 If necessary bend the pipe to fit along the bottom of the indoor unit Then pull it out through the appropriate hole The pipe should not project from the rear of the indoor unit The bending radius should be 4 inch or more 6 Pass the pipe through the hole in the wall 7 For further details on how to connect to the outdoor unit and purge the air refer to page 13 gt The pipe will be insulated and fixed permanently into position after finishing the installation and the gas leak test refer to page 14 for further details gt DO NOT WALL UP THE PIPE CONNECTION All refrigerant pipe connection must be easy accessible and serviceable2. Screws on terminal block must not be unscrewed with the torque less than 0 87 ftelb KA When you install the unit make first refrigerant connections and then elec trical connections Connect the air conditioner to grounding system before performing the electrical connection lf unit is uninstalled first disconnect electrical cables then refrigerant connections 1 Extend the assembly cable if necessary 2 Open the front grille by pulling on the tabs on the lower right and left sides of the indoor unit 3 Remove the screw securing the connector cover 4 Pass the assembly cable through the rear of the indoor unit and connect the assembly cable to terminals as seen in the picture gt Each wire is labeled with the corresponding terminal number 5 Pass the other end of the cable through the 2 56inch hole in the wall 6 Close the connector cover tightening the screw carefully 7 Close the front grille 8 Remove the terminal board cover on the side of the outdoor unit 9 Connect the cables to the terminals as seen in the picture gt Each wire is labeled with the corresponding terminal number 10 Connect the grounding conductor to the grounding terminals 11 Close the terminal board cover tightening the screw carefully 12 Connect the power cable to the indoor unit 13 For further details on how to plug the other end of the assembly cable into the outdoor unit refer to installation manual of t
3. gt Incase welding the pipe the gas nitrogen must be blown into the parts Air Marketing Group LLC 41 Kinderkamack Rd Park Ridge NJ 07656 Tel 201 782 1782 Fax 201 782 1783 Web www amgair com Email info amgair cor INSTALLING THE AIR CONDTIONER Installing and Connecting the Drain Hose of the Indoor Unit When installing the drain hose for the indoor unit check if condensation draining is adequate When passing the drain hose through the2 56 inch hole drilled in the wall check the following 0 0 0 0 _45em less Ditch The hose must The end of the drain DoNOTbendthehose Keep a clearance of at Do NOT place the end NOT slant upwards hose must NOT be in different directions least 2 inch between of the drain hose ina placed under water the end of the hose hollow and the ground Drain hose installation Shield 1 If necessary connect the 6 6ft extension drain hose to the drain hose DS ann 7b IO UUIHI DUES RE a Baie ZO 2 If you use the extension drain hose insulate the inside of the extension drain Drain hose Extension drain hose hose with a shield 3 Fitthe drain hose into 1 of 2 drain hose holes then fix the end of the drain hose tightly with a clamp gt If you don t use the otherdrain hose hole block it with a rubber stopper 4 Pass the drain hose under the refrigerant pipe keeping the drain hose tight 5 Pass the drain hose through the hole in t
4. Air Marketing Group LLC 41 Kinderkamack Rd Park Ridge NJ 07656 Tel 201 782 1782 Fax 201 782 1783 Web www amgair com Email info amgair cor Cutting or Extending the Pipe A 24 6ft pipe is supplied with the air conditioner optional The length of the pipe can be Extended up to 49 2 ft Shortened as required ENGLISH 1 Make sure that you have the required tools pipe cutter reamer flaring tool and pipe holder 2 If you want to shorten the pipe cut it using a pipe cutter ensuring that the cut edge remains at 90 with the side of the pipe see examples of correctly and incorrectly cut edges below 90 Oblique 3 To prevent a gas leak remove all burrs at the cut edge of the pipe using a reamer 4 Puta flare nut slightly into the pipe and modify the flare Outer Diameter D Depth A 1 4 inch 0 05 inch 3 8 inch 0 07 inch 1 2 inch 0 08 inch 5 8 inch 0 09 inch 5 Check if you flared the pipe correctly see examples of incorrectly flared pipes below I N Inclined Damaged Surface Cracked Uneven Thickness 6 Align the pipes to connect them easily Tighten the flare nuts first with your hands and then with a torgue wrench applying the following torgue Outer Diameter Torgue 1 4 inch 10 1 12 3 ft lb 3 8 inch 18 1 20 3 ft lb 1 2 inch 27 5 30 4 ft lb 5 8 inch 31 8 34 7 ft lb 7 For further details on how to connect to the outdoor unit and purge the air refer to page 13
5. 13 ee gs ELe cciccccccececccenceccneneccnenssceneene 13 COMPLETING THE INSTALLATION m Fixing the Indoor Unit in Place ccc cece cece cece teen eeeeee 14 m Final Check and Trial Operation 00s cceeee cece eee eee e ee eeee 15 m Providing Information for User 00 ccccecee eee eee eee ee eeeeeeee 16 Air Marketing Group LLC 41 Kinderkamack Rd Park Ridge NJ 07656 Tel 201 782 1782 Fax 201 782 1783 Web www amgair com Email info amgair cor ENGLISH Safety Precautions Keep this installation manual together with the user s manual in a handy place so that you can find it whenever you need to see it after reading this manual thoroughly Make sure to read the following safety precautions carefully before installation Make sure to observe the cautions specified in this manual Conduct a test run of the unit after installation and then explain all system functions to the owner The indications and meanings are as shown below WARNING _ This indicates the possibility of serious injury or death gt Installation must be carried out by a qualified installer gt Installers are required to read the general information carefully for safety gt Do not put the unit near dangerous substances to prevent fire explosion or injury and do not expose the unit to direct sunlight gt Do not install the unit by yourself owners Incorrect installation of the unit could cause injury
6. H meters maximum Moms T 23 6 inch total pipe Height p minimum L meters maximum TA total pipe length 11 8 inch JA B p minimum 11 8 inch minimum Model 50 80 e Main power switch Make at least one round It will reduce noise and vibration K The appearance of the unit may be different from the diagram depending on the model Air Marketing Group LLC 41 Kinderkamack Rd Park Ridge NJ 07656 Tel 201 782 1782 Fax 201 782 1783 Web www amgair com Email info amgair con Accessories The following accessories are supplied with the air conditioner The number of each accessory is indicated in parentheses gt Accessories in the Indoor Unit Case Installation Manual 1 User s Manual 1 Batteries for Remote Control 1 Remote Control 2 Installation Plate 1 The following connection accessories are optional If they are not supplied you should obtain them before installing the air conditioner 3 wire 2 wire Assembly Pipe Assembly Pipe Assembly Pipe PET3 Foam Tube Vinyl Tape 2 Power Cable Assembly Cable 1 4inch 1 3 8inch 1 1 2inch 1 Insulation 1 26 35 52K Q Pipe Clamps B 3 Cement Nail 6 M4 x 16 Drain Hose Putty 100g 1 Tapped Screws 6 length 6 56ft 1 Pipe Clamps A 3 Qe Q If these accessories
7. are supplied they will be in the accessory box Cy Q gt Air Marketing Group LLC 41 Kinderkamack Rd Park Ridge NJ 07656 Tel 201 782 1782 Fax 201 782 1783 Web www amgair com Email info amgair cor Fixing the Installation Plate ENGLISH Before fixing the installation plate to the wall or window frame you must determine the position of the 2 56inch hole through which the cable pipe and hose pass to connect the indoor unit to the outdoor unit When facing the wall the pipe and cable can be connected from the Right Left Underside right Rear right or left 1 Determine the position of the pipe and drain hose hole as seen in the picture and drill the hole with an inner diameter of 2 56inch so that it slants slightly downwards 2 If you fix the indoor unit to a Follow step s Wall 3 Window frame Ato6 3 Fix the installation plate to the wall giving attention to the weight of the indoor unit oe Pipe hole gt Ifyou mount the plate to a concrete wall with anchor bolts the anchor 2 56 inch 65mm bolts must not project more than 0 8inch 20mm iall 4 Determine the positions of the wooden uprights to be attached to the window frame MH026FNCA MH035FNCA MH052FNCA 5 Attach the wooden uprights to the window frame giving attention to the inch mm inch mm weight of the indoor unit
8. strong Wall that prevents vibration and is strong enough to hold the enough to hold the product weight product weight amp Where there is no risk of flammable gas leakage Out of the direct sunlight i amp When installing the unit at a high place be sure to fix the unit ENGLISH 3 3ft or more away from the TV or radio legs to prevent the screen from being distorted or noise from being amp 9 9f or more away from the TV or radio to prevent the screen generated i I from being distorted or noise from being generated As far away as possible from fluorescent and incandescent lights Install the unit horizontally so that the remote control can be operated well A place where the air filter can be replaced easily CAUTION Avoid the following places to prevent malfunction of the unit Where there is machine oil Salty environment such as the seaside areas Where sulfide gas exists Other special atmosphere areas Observe the clearances and maximum lengths as seen in the picture below when installing the air conditioner a 11 8 inch or more 49 inch fits SR uil 49inch or more malay or more Al i i i in aes soin Wrap the refrigerant pipes and the drain i L Youcan select the direction hose with the absorbent pad and vinyl of draining left or right tape Refer to page 15 for further details CAUTIONS 9 9ft as minimum pipe length It will reduce noise and vibration
9. 782 1783 Web www amgair com Email info amgair con Final Check and Trial Operation ENGLISH To complete the installation perform the following checks and tests to ensure that the air conditioner operates correctly 1 Check the following Strength of the installation site Tightness of pipe connection to detect gas leak Electric wiring connection Heat resistant insulation of the pipe Drainage Grounding conductor connection Correct operation follow the steps below ooo 2 Press the button and check the following The indicator on the indoor unit lights up The airflow blade opens and the fan gears up for operation Turbo Power t 3 Press any button and check the following The appropriate indicator lights up and the air conditioner operates according to the selected mode or function 4 Press the 2 button and check the following The airflow blades work properly Air Marketing Group LLC 41 Kinderkamack Rd Park Ridge NJ 07656 Tel 201 782 1782 Fax 201 782 1783 Web www amgair com Email info amgair cor Providing Information for User After finishing the installation of the air conditioner explain the following to the user refer to appropriate pages in the User s Manual 1 How to start and stop the air conditioner 2 How to select the modes and functions 3 Howto adjust the temperature and fan speed 4 Howto adjust
10. A 472 120 5 51 140 B 1 06 27 1 34 34 6 Attach the installation plate to the wooden uprights using tapping screws as c 2 68 68 2 68 68 seen in the picture Purging the Indoor Unit Upon delivery there may be inert gas inside the indoor unit Purge the gas from the indoor unit before connecting the assembly pipe Unscrew the caps at the end of each pipe Result All inert gas exhausts from the indoor unit gt To prevent dirt or foreign substances from getting into the pipes during installation do NOT remove the caps completely until you are ready to connect the pipes Air Marketing Group LLC 41 Kinderkamack Rd Park Ridge NJ 07656 Tel 201 782 1782 Fax 201 782 1783 Web www amgair com Email info amgair con Installing and Connecting the Assembly Pipe of the Indoor Unit Connect indoor and outdoor units with field supplied copper pipes by means of flare connections Use insulated seamless refrigeration grade pipe only Cu DHP type according to ISO1337 degreased and deoxidized suitable for operating pressures of at least 4200 kPa and for burst pressure of at least 20700 kPa Under no circumstances must sanitary type copper pipe be used There are 2 refrigerant pipes of different diameters 4 The smaller one is for the liquid refrigerant Thelarger one is for the gas refrigerant Ashort pipe is already fitted to the air conditioner You may need to extend the pipe using the assembly pipe optional
11. an actual room temperature and a sensed temperature by the air conditioner when heating Switch No Switch ON Switch OFF K5 3 6 F compensation 9 F compensation Air Marketing Group LLC 41 Kinderkamack Rd Park Ridge NJ 07656 Tel 201 782 1782 Fax 201 782 1783 Web www amgair com Email info amgair con Fixing the Indoor Unit in Place After checking for gas leaks in the system insulate the pipe hose and cables Then place the indoor unit on the installation plate 1 To avoid condensation problems place heat resistant polyethylene foam separately around each refrigerant pipe in the lower part of the indoor unit Wrap the refrigerant pipe and the drain hose in the rear of the indoor unit with the absorbent pad x gt Wind the pipe and hose three times to the end of the indoor unit with the absorbent pad 0 79inch interval 3 Wind the pipe assembly cable and drain hose with insulation tape 4 Place the bundle the pipe assembly cable and drain hose in the lower part of the indoor unit carefully so it doesn t project from the rear of the indoor unit Installation plate 5 Hook the indoor unit to the installation plate and move the unit to the right and left until it is securely in place 6 Wrap the rest of the pipe with vinyl tape 7Attach the pipe to the wall using clamps optional Air Marketing Group LLC 41 Kinderkamack Rd Park Ridge NJ 07656 Tel 201 782 1782 Fax 201
12. due to fire electric shock and water leakage or from the unit falling Consult a dealer or a qualified installer gt Install the unit in a place where it is strong enough to hold the product weight When installed in place where it is not strong enough to withhold the product weight the unit could fall and cause injury gt The units must be installed according to distances declared in order to permit accessibility from each side either to guarantee correct operation of maintenance or repairing products The unit s parts must be reach able and removable com pletely under safety condi tion for people or things gt Use the specified wires to connect the indoor and outdoor units securely and attach the wires firmly to the terminal block connecting sections so that the pressure is not applied to the sections Inappropriate connection and fixing could cause fire gt Avoid the use of an extension cord and do not share the power outlet with other appliances Incomplete connection defective insulation or exceeding the permissible current may cause electric shock or fire gt Make sure that the refrigerant gas does not leak after completing the installation gt If the refrigerant gas of the indoor unit leaks and comes into contact with the fan heater space heater or stove harmful substances will be generated gt Perform the installation securely referring to the installation manual Incomplete in
13. es Obtain the consent by a qualified installer before connecting the unit to the power supply system CAUTION This indicates the possibility of serious injury or damage to environments when operated incorrectly gt Fasten a flare nut with a torque wrench as specified in this installation manual When fastened too tight a flare nut may break after along period of time and cause refrigerant leakage gt To prevent injury when accidentally touching the indoor unit fan install the indoor unit on a place higher than 2 5m gt The air conditioner must be installed according to the national electrical regulations gt The maximum input power amp current is measured according to the IEC standard and the input power amp current is measured according to the ISO and EN14511standard 41 Kinderkamack Rd Park Ridge NJ 07656 Tel 201 782 1782 Fax 201 782 1783 Web www amgair com Email info amgair cor Choosing the Installation Location Indoor Unit Outdoor Unit Where airflow is not blocked Where it is not exposed to strong wind Where cool air can be distributed throughout the room Well ventilated and dustless places Install the refrigerant piping length and the height Out of the direct sunlight and rain difference of both indoor and outdoor units as 4 amp Where neighbors are not annoyed by operation sound or hot air indicated in the installation diagram Solid wall or support that prevents vibration and is
14. exo INSTALLATION MANUAL MH FNCA Series ENGLISH ESPA OL Sa sr iS Zz lt a TE _ Ale Marketing Group UC Free Joint Multi Air Conditioner Cooling and Heating INVERTER OW DB98 29163A 1 Air Marketing Group LLC 41 Kinderkamack Rd Park Ridge NJ 07656 Tel 201 782 1782 Fax 201 782 1783 Web www amgair com Email info amgair cor ENGLISH Air Marketing Group LLC Q 41 Kinderkamack Rd Park Ridge NJ 07656 Tel 201 782 1782 Fax 201 782 1783 Web www amgair com Email info amgair cor Contents PREPARING FOR INSTALLATION m Safety Precautions ccc cece cece eect eee e cece eee eneeenees 3 m Choosing the Installation Location eeeeeeeeeeeeeeeneeneese 5 MACCESSONIES scr tar pinnicumen demu rasdisimdatesrabedadestatsuamonennen 6 INSTALLING THE AIR CONDITIONER m Fixing the Installation Plate ueeeeeeeeeenreeereeneenrrne 7 E Purging the Indoor Unit 3 nesisiss ccs eccesdacdacaes tes Sr ir Ais sis ia 7 u Installing and Connecting the Assembly Pipe of the Indoor Unit 8 m Cutting or Extending the Pipe cece e cece e eee eeee eens 9 u Installing and Connecting the Drain Hose of the Indoor Unit 10 m Changing Direction of the Drain Hose cece cece ee eeee 11 m Connecting the Assembly Cable ueeeeeeeeneeenreenrennne 12 m Assigning Address to Indoor Unit cece cece cece eee eeeeee
15. he outdoor unit gt In Russia and Europe consult with the supply authority to determine the supply system impedance before installation Air Marketing Group LLC 41 Kinderkamack Rd Park Ridge NJ 07656 Tel 201 782 1782 Fax 201 782 1783 Web www amgair com Email info amgair cor NSTALLING THE IR CONDTIONER Assigning Address to Indoor Unit ENGLISH Before installing the indoor unit assign an address to the indoor unit according to the air conditioning system plan 1 Open the front grille by pulling on the tabs on the lower right and left sides of the indoor unit 2 Remove the screw securing the cover PCB 3 Remove the cover PCB Cover PCB 4 The address of the indoor unit is assigned by adjusting MAIN SW02 5 The MAIN address is for communication between the indoor unit and the outdoor unit Therefore you must set it to operate the air conditioner properly PEN 0 6 Itis required to set the RMC address if you install the wired remote controller and or the centralized controller 7 Ifyou install optional accessories such as the wired remote controller centralized controller etc see an appropriate installation manual SW02 MAIN 8 Refer to the outdoor unit installation manual for the details Additional Functions il Compensation for lost temperature in heating operation K5 K6 K7 K8 Reduces the difference between
16. he wall Check if it slants downwards as seen in the picture gt The hose will be fixed permanently into position after finishing the installation and the gas leak test refer to page 14 for further details gt DO NOT WALL UP THE DRAIN HOSE CONNECTION Drain hose connection must be easy accessible and serviceable 6 Air Marketing Group LLC 41 Kinderkamack Rd Park Ridge NJ 07656 Tel 201 782 1782 Fax 201 782 1783 Web www amgair com Email info amgair cor Changing Direction of the Drain Hose ENGLISH You can select the direction of the drain hose depending on where you want to install the indoor unit 1 Detach the rubber cap with the flyer Screw hole Screw 2 Detach the drain hose by pulling it and turning to the left Drain hose 3 Insert the drain hose by fixing it into the groove of the drain hose and the outlet of the drain pan Drain pan outlet 4 Attach the rubber cap with a screwdriver by turning it to the right until it fixes to the end of the groove Air Marketing Group LLC 41 Kinderkamack Rd Park Ridge NJ 07656 Tel 201 782 1782 Fax 201 782 1783 Web www amgair com Email info amgair cor Connecting the Assembly Cable Outdoor unit i I i I i I i Indoor unit 1 2 F1 F2 Earth Omog Earth terminal Ji me a Or terminal F1 F2 zeH QR ee
17. irements gt This product is an air conditioning system and contains a coolant that must be recovered and disposed of in an appropriate way by qualified personnel At the end of the life cycle take it to a proper recycling or disposal center or return it to the dealer so that it can be disposed correctly gt Check if the voltage and the frequency of the main power supply are those required for the unit to be installed and check the connection gt Make sure that properly sized disconnecting and safety switches are installed gt Grounding the unit Do not connect the ground to a gas pipe water pipe lightning rod or telephone grounding Defective grounding could cause electric shock gt Do not install the unit in a place where it is exposed to inflammable gas leakage There is a risk of explosion gt Install a ground leakage breaker depending on the installation place where it is humid If not it may cause electric shock gt Perform the drainage piping work securely according to the installation manual If not water could drop from the unit and household goods could get wet and damaged Air Marketing Group LLC gt Do not attempt to repair move modify or reinstall the unit on your own Make sure that these installations are carried out by qualified personnel to avoid electric shock or fire gt Use the unit on a single outlet circuit Do not share the power outlet with other applianc
18. stallation could cause personal injury due to fire electric shock and water leakage or from the unit falling gt Attach the electrical cover to the indoor and outdoor unit securely If not it could result in fire or electric shock due to dust or water gt Make sure to use the part provided or specified parts for the installation work The use of defective parts could cause an injury or leakage of water due toa fire an electric shock the unit falling etc gt Make sure to turn off the main power when setting up the indoor unit electrical circuit or power cords There is a risk of electric shock Air Marketing Group LLC 41 Kinderkamack Rd Park Ridge NJ 07656 Tel 201 782 1782 Fax 201 782 1783 Web www amgair com Email info amgair cor WARNING e This indicates the possibility of serious injury or death gt The unit should be installed in accordance with the National Electrical regulations gt Ensure that the national safety code requirements have been followed for the main supply circuit Ensure that a properly sized and connected ground wire is in place gt Check the unit for damage that may have taken place during transportation and do not install or use damaged equipment gt All of the manufacturing and packaging material used for your new appliance are compatible with the environment and can be recycled gt Dispose of the packaging material in accordance with the local requ
19. the airflow direction 5 Howto set the timers 6 Howto clean and replace the filters gt When you complete the installation successfully hand over the User s Manual and this Installation Manual to the user for storage in a handy and safe place Air Marketing Group LLC 41 Kinderkamack Rd Park Ridge NJ 07656 Tel 201 782 1782 Fax 201 782 1783 Web www amgair com Email info amgair cor Ale Marketing Group UC Air Marketing Group LLC 41 Kinderkamack Rd Park Ridge NJ 07656 Tel 201 782 1782 Fax 201 782 1783 Web www amgair com Email info amgair cor ELECTRONICS Air Marketing Group LLC 41 Kinderkamack Rd Park Ridge NJ 07656 Tel 201 782 1782 Fax 201 782 1783 Web www amgair com Email info amgair cor
Download Pdf Manuals
Related Search