FS600LED
Contents
1. Rev 4 15 User Instructions FS600LED Introduction Unpacking Thank you for purchasing the FS600LED by ADJ Prod ucts LLC Every FS600LED has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during shipping If the carton appears to be damaged carefully inspect your fixture for any damage and be sure all accessories necessary to operate the unit has arrived intact In the case damage has been found or parts are miss ing please contact our toll free customer support number for further instructions Do not return this unit to your dealer without first contact ing customer support Introduction The ADJ FS600LED is part of a continuing pursuit to create high quality intelligent lighting The FS600LED is a modern 60W LED follow spot It features a bright 60W LED 8 colors variable strobe speed and dimming capabilities This fixture is suitable for theaters studios retail stores and other similar locations Customer Support ADJ Products LLC provides a customer sup port line to provide set up help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www adj com for any comments or sugges tions Service Hours are Monday through Friday 8 00 a m to 4 30 p m Pacific Standard Time Voice 323 582 3322 Fax 323 582 3108 E mail support adj com Warning2. S LIMITED WARRANTY PERIODS e Lighting Products 1 year 365 days Limited Warranty Such as Special Effect Lighting Intelligent Lighting UV lighting Strobes Fog Machines Bubble Machines Mirror Balls Par Cans Trussing Lighting Stands etc excluding LED and lamps e Laser Products 90 Day Limited Warranty e L E D Products 2 year 730 days Limited Warranty excluding motors PCB boards and power supplies which have a 1 year 365 day Limited Warranty and batteries which have a 180 day limited warranty Only the L E D s carry a 3 year warranty ADJ Products LLC www adj com FS600LED User Manual Page 11 FS600LED Specifications Model FS600LED Voltage 100V 240V 50 60Hz LEDs 1 x 60 Watt LED Beam Angle 18 26 Degrees Working Position Any safe working position Power Consumption 80W Fuse 3 Amp Weight Dimensions 18lbs 7 8Kgs 11 5 L x 19 25 W x 14 75 H 290 x 484 x 370mm 8 Colors 3 DMX Channels 2 Year 730 days Colors DMX Channels Warranty Auto Sensing Voltage This fixture contains a automatic volt age switch which will auto sense the voltage when it is plugged into the power source Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice ADJ Products LLC 6122 S Eastern Ave Los Angeles CA 90040 USA Tel 323 582 2650 Fax 323 725 6100 Web www adj com E mail info ad
3. To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures war ranty In the unlikely event your unit may require service please contact ADJ Products LLC PLEASE recycle the shipping carton when ever possible ADJ Products LLC www adj com FS600LED User Manual Page 2 mol ol 0 i D General Instructions To optimize the performance of this product please read these operat ing instructions carefully to familiarize yourself with the basic operations of this unit These instructions contain important safety information regarding the use and maintenance of this unit Please keep this manual with the unit for future reference FS600LED Features 8 Colors Strobing e Adjustable Iris e Shutters for Manual Framing Dimming 0 100 e DMX 512 protocol 3 Pin amp 5 Pin DMX Connection e 3 DMX Channels FS600LED Warranty Registration The FS600LED carries a 2 year limited warranty Please fill out the enclosed warranty card to validate your purchase All returned service items whether under warranty or not must be freight pre paid and accompany a return authorization R A number The R A number must be clearly written on the outside of the return package A brief description of the problem as well as the R A number must also be writ
4. cables should be made with a male and female XLR connector on either end of the cable Also remember that DMX cable must be daisy chained and cannot be split ground lug on the XLR connector Do not connect the cable s shield ADJ Products LLC www adj com FS600LED User Manual Page 5 Notice Be sure to follow figures two and three Se when making your own cables Do not use the Figure 1 FS600LED Set Up conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behavior COMMON DMX512 OUT DMX512 IN 3 PIN XLR DMX 3 PIN XLR XLR Male Socket XLR Female Socket 1 E g 2 yr Figure 3 Special Note Line Termination When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior A terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male XLR connector DATA and DATA This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line Using a cable terminator ADJ part number Z DMX T will decrease the possibilities of erratic behavior oe Termination reduces signal errors and avoids signal transmission problems O and interference It is always advisable G X to connect a DMX terminal Resistance Figure 2 XLR Pin Configuration Pin 1 Ground Pin 2 Data Complim
5. All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty ADJ Products LLC will pay return shipping charges only to a designated point within the United States If the entire instrument is sent it must be shipped in it s original package No accessories should be shipped with the product If any accessories are shipped with the product ADJ Products LLC shall have no liability whatsoever for loss of or damage to any such accessories nor for the safe return thereof C This warranty is void if the serial number has been altered or removed if the product is modified in any manner which ADJ Products LLC concludes after inspection affects the reliability of the product if the product has been repaired or serviced by anyone other than the ADJ Products LLC factory unless prior written authorization was issued to purchaser by ADJ Products LLC if the product is damaged because not properly maintained as set forth in the instruction manual D This is not a service contract and this warranty does not include maintnance cleaning or periodic check up During the period specified above ADJ Products LLC will replace defective parts at its expense with new or refurbished parts and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of ADJ Products LLC under this warranty shall be lim
6. ent negative 5 SaaS eee Pin 3 Data True positive 120 Ohm 1 4 W between PIN 2 DMX and PIN 3 DMX of the last fixture Figure 4 5 Pin XLR DMX Connectors Some manufactures use 5 pin DMX 512 data cables for DAIA transmission in place of 3 pin 5 pin DMX fixtures may be implemented in a 3 pin DMX line When inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores The chart below details a proper cable conversion 3 Pin XLR to 5 Pin XLR Conversion 3 Pin XLR Female Out 5 Pin XLR Male In Sata Compliment sana E A ADJ Products LLC www adj com FS600LED User Manual Page 6 FS600LED Operating Instructions DMX Mode Operating through a DMX controller gives the user the freedom to create their own programs tailored to their own individual needs This function also allows you to use your fixtures as spot lights The FS600LED has 3 DMX channels See page 8 for the DMX traits 1 This function will allow you to control each individual fixture s FS600LED Control Features traits with a standard DMX 512 controller 1 Iris 2 Plug in the fixture via the XLR connections to any standard DMX 2 Power Switch controller 3 3 Pin or 5 Pin DMX Input 3 Please see below for DMX values and traits 4 3 Pin or 5 Pin DMX Output FS600LED 3 Channel DMX Values amp Functions 5 Beam Shaper Value F
7. he weight of the unit when installing the fixture The equipment must be installed by a professional and it must be installed in a place where it is out of the reach of people s grasp ad Distance m 0 1 3 5 7 Unit not responding to DMX 1 Check that the DMX cables are connected properly and are wired correctly pin 3 is hot on some other DMX devices pin 2 may be hot Also check that all cables are connected to the right connectors it does matter which way the inputs and outputs are connected ADJ Products LLC www adj com FS600LED User Manual Page 9 ADJ Products LLC www adj com FS600LED User Manual Page 10 FS600LED Warranty MANUFACTURER S LIMITED WARRANTY A ADJ Products LLC hereby warrants to the original purchaser ADJ Products LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase see specific warranty period on reverse This warranty shall be valid only if the product is purchased within the United States of America including possessions and territories It is the owner s responsibility to establish the date and place of purchase by acceptable evidence at the time service is sought B For warranty service you must obtain a Return Authorization number RA before sending back the product please contact ADJ Products LLC Service Department at 800 322 6337 Send the product only to the ADJ Products LLC factory
8. ited to the repair of the product or replacement thereof including parts at the sole discretion of ADJ Products LLC All products covered by this warranty were manufactured after August 15 2012 and bear indentifying marks to that effect E ADJ Products LLC reserves the right to make changes in design and or improvements upon its products without any obligation to include these changes in any products theretofore manufactured No warranty whether expressed or implied is given or made with respect to any accessory supplied with products described above Except to the extent prohibited by applicable law all implied warranties made by ADJ Products LLC in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product after said period has expired The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall ADJ Products LLC be liable for any loss or damage direct or consequential arising out of the use of or inability to use this product This warranty is the only written warranty applicable to ADJ Products LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published MANUFACTURER
9. j com A D J Supply Europe B V Junostraat 2 6468 EW Kerkrade Netherlands service adjgroup eu www adj eu Tel 31 45 546 85 00 Fax 31 45 546 85 99 Follow Us On t facebook com americandj twitter com americandj youtube com adjlighting
10. roller sends DMX data instructions from the controller to the fixture DMX data is sent as serial data that trav els from fixture to fixture via the DATA IN and DATA OUT XLR ter minals located on all DMX fixtures most controllers only have a DATA QUT terminal DMX Linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compli ant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain Data Cable DMX Cable Requirements For DMX Operation The FS600LED can be controlled via DMX 512 protocol The FS600LED has 3 DMX channels Your unit and your DMX controller require a stan dard 3 pin XLR connector for data input and data output Figure 1 We recommend Accu Cable DMX cables If you are making your own cables be sure to use standard 110 120 Ohm shielded cable This cable may be purchased at almost all pro lighting stores Your
11. s e During long periods of non use disconnect the unit s main power e Always mount this unit in safe and stable matter e Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to the point they exit from the unit e Cleaning The fixture should be cleaned only as recommended by the manufacturer See page 10 for cleaning details Heat The appliance should be situated away from heat sources such as radiators heat registers stoves or other appliances inclu ding amplifiers that produce heat e The fixture should be serviced by qualified service personnel when A The power supply cord or the plug has been damaged B Objects have fallen or liquid has been spilled into the appliance C The appliance has been exposed to rain or water D The appliance does not appear to operate normally or exhibits a marked change in performance ADJ Products LLC www adj com FS600LED User Manual Page 4 FS600LED Set Up Power Supply The ADJ FS600LED contains a automatic voltage switch which will auto sense the voltage when it is plugged into the power source With this switch there is no need to worry about the cor rect power voltage this unit can be plugged in anywhere DMX 512 DMX is short for Digital Multiplex This is a universal pro tocol used as a form of communication between intelligent fixtures and controllers A DMX cont
12. ten down on a piece of paper included in the shipping carton If the unit is under warranty you must provide a copy of your proof of purchase invoice You may obtain a R A number by contacting our customer support team on our customer support number All pack ages returned to the service department not displaying a R A number on the outside of the package will be returned to the shipper ADJ Products LLC www adj com FS600LED User Manual Page 3 FS600LED Safety Precautions To reduce the risk of electrical shock or fire do not expose this unit rain or moisture e Do not spill water or other liquids into or on to your unit Do not attempt to operate this unit if the power cord has been frayed or broken Do not attempt to remove or break off the ground prong from the electrical cord This prong is used to reduce the risk of electrical shock and fire in case of an internal short Disconnect from main power before making any type of connection e Do not remove the cover under any conditions There are no user serviceable parts inside e Never operate this unit when it s cover is removed e Never plug this unit in to a dimmer pack e Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall Do not attempt to operate this unit if it becomes damaged e This unit is intended for indoor use only use of this product out doors voids all warrantie
13. unction 7 ease MASTER DIMMER 8 Beam Shaper 0 255 0 100 COLOR WHITE FS600LED Control Panel r ADJ Products LLC www adj com FS600LED User Manual Page 7 2 0 31 32 63 RED 64 95 YELLOW 96 127 BLUE 128 159 GREEN 160 191 ORANGE 192 223 UV 224 255 WARM WHITE 0 15 16 131 132 139 140 181 182 189 190 231 232 239 240 247 248 255 STROBING NO FUNCTION STROBING SLOW FAST NO FUNCTION SLOW OPEN FAST CLOSE NO FUNCTION SLOW CLOSE FAST OPEN NO FUNCTION RANDOM STROBE NO FUNCTION Functions 1 Color Buttons Choose from 7 different colors plus white 2 Dimmer This slider adjusts output intensity 3 Strobe This slider activates and adjusts the strobing func tion ADJ Products LLC www adj com FS600LED User Manual Page 8 FS600LED Gobo Holder FS600LED Fuse Replacement The unit comes with a gobo holder located on the top of the unit The fuse holder located at the rear of the unit above the power cord Remove the gobo holder by sliding it up and out To install a gobo Disconnect from the main power supply Insert a standard flat head remove the retainer ring It is easier to remove using needle nose screw driver in to the fuse holder housing located on the back of the pliers Once the ring is removed insert
14. your desired gobo and reinsert unit Turn the screwdriver in counter clockwise direction to remove the the retainer ring The gobo size is 27mm with a viewing size of 23mm fuse holder Remove the old fuse and discard it replace the fuse with Slide the gobo holder back into the slot the same type Insert the fuse back into it s housing FS600LED Cleaning FS600LED Photometric Chart Due to fog residue smoke and dust cleaning the internal and exter Lux18 22640 3383 1328 709 nal optical lenses must be carried out periodically to optimize light Lux26 13390 1654 633 340 output 1 Use normal glass cleaner and a soft cloth to wipe down the outside casing Clean the external optics with glass cleaner and a soft cloth every 20 days Always be sure to dry all parts completely before plugging the unit back in FS600LED Installation Cleaning frequency depends on the environment in which the fixture operates i e smoke fog residue dust dew The unit should be mounted using a mounting clamp not provided affixing it to the mounting bracket that is provided with the unit Always ensure that the unit is firmly fixed to avoid vibration and slip Listed below are a few common problems the user may encounter ping while operating Always ensure that the structure to which you with solutions are attaching the unit is secure and is able to support a weight of 10 times the unit s weight Also always use a safety cable that can hold 12 times t
Download Pdf Manuals
Related Search
FS600LED fs600led