Installation, User Operation, & Maintenance Manual
Contents
1. above general warranty for its economy fryers and cookers the Company warrants to the original user any mild Stainless steel fry tank or cooking vessel to be free from defects for a period of one 1 year prorated from the date of manufacture Labor and freight shall be the responsibility of the end user Gold Line Fryers In addition to the above general warranty for its standard fryers and cookers the Company warrants to the original user any stainless steel fry tank or cooking vessel to be free from defects for a period of ten 10 years from the date of manufacture Labor and freight shall be the responsibility of the end user Pasta Cooker In addition to the above general warranty for its standard fryers and cookers the Company warrants to the original user any stainless steel fry tank or cooking vessel to be free from defects for a period of one 1 year from the date of manufacture Labor and freight shall be the responsibility of the end user Limitations to Fry Tank and Cooking Vessel Warranty After the expiration of the general warranty period any additional warranty on fry tanks or cooking vessels shall only obligate the Company to repair or replace at its option any fry tank or cooking vessel which it determines to be defective Claims under this item shall be supported by a statement detailing the defect and the Company may require the return of the fry tank or cooking vessel claimed to be defective Labor and freight shall be the respon2. the bottom of the motor If the motor is hot to the touch wait at least 15 minutes before trying this 4 If the pump starts and stops again in a short time or if it hums but does not pump there is a restriction somewhere in the filter screen or in the pump itself Go to Step 5 If there is no reaction from the pump go to step 6 5 Allow the oil shortening in the filter pan to cool then empty the pan and verify that the filter paper and screen assembly is assembled correctly Disassemble the filter screen and look for blockages of sediment or solid shortening within 6 Problem is with the motor pump or the wiring Remove the motor from the filter and bench test by connecting a 120V line to the motor leads If it runs the problem is with the wiring between the motor and the power supply If it does not run the motor needs to be replaced 1 If solid shortening is being used allow HOT oil to recirculate through the lines long enough to ensure that all solidified shortening has melted 2 After all the shortening oil has been pumped back into the fryer inspect the filter paper envelope Make sure that any excess sediment is removed from the top of the filter paper envelope 3 If the filter paper envelope is dirty or torn disassemble the filter screen assembly Inspect for blockages in the lines Replace with a clean filter paper envelope WARNING Only use filter paper envelopes from Anets that have been specifically designed for t
3. you may have other rights which vary from state to state Anets Inc P O Box 501 Jct 1 89 amp I 93 Concord NH 03302 0501 509 Route 3A Bow NH 03304 USA Tel 603 225 6684 Fax 603 228 5231 www ANETS com L14 022 RO Printed in U S A L20 344 Rev 2 12 Left Blank Intentional L20 344 Rev 2 13 Anets Dependable Foodservice Equipment PO Box 501 Concord NH 03302 1 603 225 6684 Fax 603 228 5231 www anets com Keep this Manual in a Convenient Location for Reference L20 344 Rev 2
4. 62 CSTR PMF 2 W TP PL PP11381 CSTR PMF 2 LOCKING W TP PL 21 P0092300 NUT HEX KEP 10 24 ZN 22 24 C7842 00 FLTR NOZZLE FEM80 150 C7841 00 FLTR WLDMT FEM80 150 60160501 GRIP HDL PORTABLE FLTR 25 A6653522 FLTR HOSE 65 00 FFM80 150 27 D6170 00 JFLTR TK WLDMT FF M80 D6170 01 FLTR TK WLDMT FEM150 C10533 00 FLTR CLP PPR FFM FM 28 P9800 94 FLTR PICK UP SCRN 15 50 FFM 29 P9314 90 CPLG KNURLED CAP FLTR P U 30 31 60015903 CONN NIPPLE 3 8 MALE NPT 60033903 CONN COUPLER 3 8 NON VLVED 32 C10718 00 FLTR WLDT PICK UP TU FFM80 C10718 01 FLTR WLDT PICK UP TU FFM150 33 34 60015902 CONN NIPPLE 1 2 FEMALE NPT C10713 00 FLTR WLDMT TK CVR FEM80 C10713 01 FLTR WLDMT TK CVR FFM150 35 37 C10704 00 FLTR FR BK PNLFFM80 C10704 01 FLTR FR BK PNL FFM150 C10702 00 FLTR PMP ELEC BOX FFM PP10752 SCR 10 32 X 1 2 PNH PHH ZN TF 38 39 40 C10705 00 FLTR FR TOP CVR FFM80 C10705 01 FLTR FR TOP CVR FFM150 C10709 00 FLTR PMP PG SPRT FFM B14185 00 FLTR PMP BOX PL FFM 41 D6168 00 FLTR PMP PG CVR FFM 42 B14183 00 FLTR PMP BOX HDL FFM C10703 OO FLTR CORD BRKT FEM80 C10703 01 FLTR CORD BRKT FFM150 A7044101 FLTR HDL PORTABLE FFM80 A7044102 FLTR HDL PORTABLE FFM150 P8025 97 SCR SHLDR 5 16 DIA X 3 8 PP10192 BUSHING STRAIN RELIEF RIGHT 60046201 SW RKR SPST 1 0 125V RED DOMESTIC PP10470 CK
5. SINETS Anets Dependable Foodservice Equipment PO Box 501 Concord NH 03302 Tel 603 225 6684 Fax 603 228 5231 Portable Filter Systems Models FFM 80 FFM 150 Installation User Operation amp Maintenance Manual Model FFM80 shown N DANGER Improper installation adjustment alteration service or maintenance can cause property damage injury or death Read the installation operating and maintenance instructions thoroughly before installing or servicing this eguipment Keep this Manual in a Convenient Location for Reference The Anets GoldenLine pain Quality Equipment For The Restaurant Supermarket and Bakery Industries L20 344 Rev 2 TABLE OF CONTENTS Shipping Container Inspection nen 2 Code Requirements see ei aaa ed kanalas kanalile 4 Filter Unit Preparation Instructions e e d Filter Diagrams E njeni ie sa sneer hasrete esaerea aies 5 Filtering Instructions 523 ija aii adcecdceawided sabesedeostsaadliatcccisiabdeiadesd 6 Oil Disposal MSETUGUONS 1 4 sie sede steed cnt aa vela atakk idu kt 7 Replacing The Filter PADE scccscsssndiceiecatseeediranedeunsigecessatensceendedes 8 Filter Troubleshooting Guide enen 9 Filter Warranty siseses TESSA Ea 9 Parts Aa ss ce vtec lea EE E i 11 Paris List odidere EEE E EEEE REEERE 12 A DANGER Read these specifications Code Requirements Installation Requirements Installation Instructions and Operati
6. T BKR RKR DPST 250V 4A INTL CE B6788202 CORD iINTERNAL DOMESTIC 49 B6788201 CORD EXTERNAL DOMESTIC 60124201 CORD EXTERNAL EXTENSION DOMESTIC ONLY B6793101 CORD INTERNAL INTL CE B6793102 CORD EXTERNAL INTL ONLY 700387 SCHEM PORTABLE FLTR FFM L20 344 Rev 2 11 ORIGINAL EGUIPMENT LIMITED WARRANTY General Warranty Anets Inc warrants to the original user of its commercial cooking appliances and related equipment that said appliances and related equipment will be free from defects in material and workmanship under normal use for a period of one 1 year from the date of installation with appropriate documentation to a maximum of fifteen 15 months from the date of manufacture subject to the following additions exceptions exclusions and limitations What is covered This warranty is limited to the repair or replacement at the Company s option without charge of any part found to be defective within the warranty period and reasonabl expenses incurred for freight and material for the installation of such part in addition the Company s obligation shall be limited to reimbursement for normal labor on such parts Anets Inc agrees to pay the Authorized Service and Parts Distributor for any labor and material required to repair or replace at the Company s option any part which may fail due to defects in material or workmanship during the above general warranty period Silver Line Fryers In addition to the
7. an electrical ground This unit is not fused Protect circuit with proper sized fuses or circuit breaker line disconnect switch circuit breaker or plug and receptacle of power cord connection should be readily accessible to the operator M WARNING A Electrical Grounding Instructions This appliance is equipped with a three prong grounding plug for your protection against shock hazard and should be plugged directly into a properly grounded three prong receptacle DO NOT cut or remove the grounding prong from this plug FILTER UNIT PREPARATION Refer to Photos On Page 4 1 Assemble filter envelope to filter screen by sliding the envelope over the filter screen folding back the open end over the filter screen Make sure the hole in the filter envelope fits over the fitting on the filter screen WARNING Only use filter paper envelopes from Anets that have been specifically designed for this filter system Using the wrong type of filter paper can cause damage to the pump system and will void the Warranty 2 Assemble filter envelope clip over folded back end of envelope and over fitting on filter screen Attach knurled retaining nut onto fitting on screen securing the assembly Attach quick connect coupling located on drain tube to knurled retaining nut Place filter unit into the filter tank Connect the filter assembly to the pump using the quick connect assembly Put the filter tank cover on the tank Connect the hose as
8. e not covered by the warranty f any other failure occurs which is not attributable to a defect in materials or workmanship it is not covered This warranty specifically excludes parts which wear or would be replaced under normal usage including but not limited to electric lamps fuses interior or exterior finishes o rings and gaskets Limits to the Warranty Outside the United States of America and Canada this warranty is limited to the replacement of parts and Anets Inc will not bear any other expense be it labor mileage freight or travel If any oral statements have been made regarding the appliance these statements do not constitute warranties and are not part of the contract of sale This limited warranty constitutes the complete final and exclusive statement with regard to warranties THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES WHETHER WRITTEN ORAL OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR WARRANTY AGAINST LATENT DEFECTS Limitations of Liability In the event of a warranty or other claim the sole obligation of Anets Inc will be the repair or replacement at the Company s option of the appliance or the component part This repair or replacement will be at the expense of Anets Inc except as limited by this warranty statement Any repair or replacement under this warranty does not constitute an extension in time to the or
9. he system is cycling use a long handled cleaning brush to wipe the bottom of the fryer and push excess crumbs through the drain and into the filter WARNING When cleaning the inside of the frypot do not damage the temperature and hi limit probes that protrude into the frypot 4 Allow the pump to run until the shortening returning into the fryer is clear of sediment then close drain valve handle and allow the fryer to refill WARNING If solid shortening is being used it is very important that all oil is allowed to flow back into the vat and none is left in the hoses Failure to do so could cause the pump to fail if the oil solidifies in the line 5 If filter powder is being used add 1 cup of powder for 14 fryers or 2 cups for 18 fryers to either the fry tank or the filter tank If added to fry tank make sure powder is completely flushed during fry tank cleaning Step 3 before closing drain valve Step 4 If added to filter tank the powder will be removed when the filter envelope is changed and the filter tank is cleaned L20 344 Rev 2 6 On gas operated thermostat models such as Anets 14G 14GS MXEG 18EG 20EG the thermostat knob can now be turned back to the desired temperature CAUTION On these models the thermostat must be set to OFF or the Gas Valve to PILOT before filtering or the burners MAY come back on if the doors are closed during filtering 7 On electric operated thermostat models such as Ane
10. his filter system Using the wrong type of filter paper can cause damage to the pump system and will void the warranty 4 If the oil still returns to the fryer slowly the problem may be a blockage within the pump itself The pump section of the motor can be easily disassembled to look for blockages of sediment or solid shortening within L20 344 Rev 2 PARTS DIAGRAM MEASURE FOR CORRECT PUMP DETAIL A i i LET 4 a 7 1 TI REPLACEMENT SEE DETAIL A VN INTERNAL ESS EXTERNAL DC INTERNAL INTL CE EXTERNAL INTL ONLY EXTERNAL EXTENSION DO L20 344 Rev 2 10 PARTS LIST P N DESCRIPTION 60161101 PMP ASSY 5GPM 1 3HP 115 230V S283 DIMA 2 25 PUMP MTR 1 3HP 115 230V SOHZ S95 DIMA 3 91 PUMP MTR 1 3HP 240V SOHZ S95 DIMA 3 91 NUT 5 16 18 FLNG LC ELB BLK STR 90 1 2 NIP BLK 1 2 X 3 1 2 CONN COUPLER 1 2 NON VLVED FLTR HDL 2 50 DIA BLUE SCR 10 24 X 1 2 SET PG ASSY VENT TU FFM B6691403 FLTR WLDMT FR FFM80 230 240V S95 POST MARCH 2012 B6691404 FLTR WLDMT FR FFM150 230 240V POST MARCH 2012 B6691405 FLTR WLDMT FR FEM80 115V POST MARCH 2012 B6691406 FLTR WLDMT FR FFM150 115V POST MARCH 2012 16 A7093502 FLTR BOT COV FFM80 INTL CE 17 60069501 SCR 10 24 X 3 8 FH PHILLIPS 18 19 20 P0011300 SCR 10 24 X 3 8 INDT HEX P60710
11. iginal warranty Parts covered under this warranty will be repaired or replaced at the Company s option with new or functionally operative parts The liability of Anets Inc on any claim of any kind including claims based on warranty express or implied contract negligence strict liability or any other legal theories will be exclusively the repair or replacement of the appliance This liability will not include and the purchaser specifically renounces any right to recover special incidental consequential or other damages of any kind including but not limited to injuries to persons damage to property loss of profits or anticipated loss of the use of this appliance If any provision of this warranty is unenforceable under the law of any jurisdiction that provision only will be inapplicable there and the remainder of the warranty will remain unaffected The maximum exclusion or limitation allowed by law will be substituted for the unenforceable provision How to Obtain Warranty Service First direct your claim to the Anets Inc Authorized Service and Parts Distributor closest to you giving complete model serial and code numbers voltage gas type and description of the problem Proof of the date of installation and or the sales slip may also be required If this procedure fails to be satisfactory write the National Service Manager Anets Inc P O Box 501 Concord NH 03302 0501 USA This warranty gives you certain specific legal rights
12. m temperature before attempting to change the paper Unplug the cord from the receptacle Disconnect the line from the pump to the filter screen Remove the filter cover Remove the filter screen assembly from the filter pan and place on a clean surface for disassembly Detach quick connect coupling on drain tube from knurled retaining nut Detach knurled retaining nut from fitting in screen Remove filter envelope clip from end of filter screen and folded back end of envelope Remove filter envelope from filter screen WARNING The oil soaked filter envelope may still be very hot and could cause burns 9 Clean the filter pan filter screen and all components thoroughly using a solution of hot water and detergent Make sure that all food and breading particles are removed from the pan and from the filter screen 10 Dry the pan the screen and all components completely before starting to reassemble 11 Follow instructions under FITTER UNIT PREPARATION to install new filter envelope ONNNBRWN L20 344 Rev 2 FILTER SYSTEM TROUBLESHOOTING GUIDE PROBLEM SOLUTION Pump does not start when the switch is activated Filtering procedure is very slow Shorten ing oil returning to the fryer very slow 1 Make sure the power cord is plugged into the proper 120 Volt receptacle 2 Turn the switch on the front of the filter to ON 3 If the pump still hasn t started depress the thermal overload button on
13. ng Instructions very carefully Failure to follow the Instructions could cause the filter system to malfunction A filter system malfunction can result in property damage serious bodily injury or death SHIPPING CONT AINER INSPECTION 1 Carefully examine the shipping container for external damage When damage is noted notify the delivery carrier immediately Save all packing materials for damage claim examination 2 Ifno external damage is noted remove the shipping container from the filter and examine the unit carefully for damage Place the filter in a safe location if damage is noted so that the freight damage claims adjuster can examine it Models Covered By This Manual FFM 80 Portable Filter System 80 Ib capacity FFM 150 Portable Filter System 150 Ib capacity Standard Accessories furnished in the shipping carton with this filter include 1 Filter Screen Assembly 2 Starter Paper Starter Pack 3 Return Hose Assembly NOTE A Parts List for each Anets Filter System is among the items shipped with each unit If an additional copy of this list is needed please contact the factory as directed on the back cover L20 344 Rev 2 NOTES L20 344 Rev 2 INSTALLATION INSTRUCTIONS FILTER ELECTRICAL SPECIFICATIONS Please make sure that your desired filter location has electrical supply factors that are suitable for this product line Reguirements are120 Volts 60 Hz 8 Amps 1 phase three wire connection including
14. sembly to the filter pump mano aro L20 344 Rev 2 FFM PORTABLE FILTER Completely Disassembled Foldable handle Pump guick connect coupling Quick connect coupling Filter tank for filter screen assembly Filter screen assembly rr Filter envelope Knurled retaining nut Filter envelope clip Hose assembly FFM PORTABLE FILTER COMPLETELY ASSEMBLED Ouick connect coupling Pump guick connect coupling Filter envelope clip Knurled retaining nut Filter envelope L20 344 Rev 2 FILTERING INSTRUCTIONS CAUTION Never operate the filter unit unless the cooking oil or shortening in the fryers has been brought up to cooking temperature WARNING Always wear protective heat resistant gloves when performing the filtering operation 1 Before filtering the shortening in a fryer turn the thermostat knob to OFF or the Gas valve to PILOT to prevent the fryer from re lighting during filtering On some models the system automatically prevents the burners from lighting when the door of the fryer is open 2 Roll filter under drain pipe extension on the fryer and slowly open drain valve handle letting all the shortening drain into the filter tank Leave this valve open ZS DANGER Never drain more than one fryer at a time the filter pan will overflow 3 Hold hose assembly nozzle over the fryer kettle turn on the pump switch and flush sediment out of the fryer While t
15. sibility of the end user How to Keep Your Warranty in Force Make sure any shipping damages are reported immediately Damages of this nature are the responsibility of the carrier and must be reported by the receiver nstall the unit properly This is the responsibility of the installer and the procedures are outlined in the manual Do not install it in a home or residence Maintain it properly This is the responsibility of the user of the appliance and the procedures are outlined in the manual Adjustments such as calibration leveling tightening of fasteners or plumbing or electrical connections normally associated with initial installation These procedures are outlined in the manual and are NOT covered by warranty f it is damaged due to flood fire or other acts of God this is not covered under this warranty Use it for what it is intended If it is used for a purpose other than for which it was intended or designed resulting damages are not covered under the warranty Make sure that it has the correct voltage gas supply and or good quality water If a failure is due to poor water quality harsh chemical action erratic voltage or gas supplies these damages are not covered under the warranty Do not materially alter or modify from the condition in which it left the factory Do not obliterate remove or alter the serial number rating plate Use only Genuine OEM parts from Anets Inc or its Authorized Parts and Service Distributors Repairs ar
16. ts MX 14E MX 14EX MX 14AA 18E 18AA 20E 14EL 14 and 14EL 17 the power switch on the control panel must be reset for the fryer to operate again IMPORTANT NOTE The pump on this filter unit is equipped with a safety that will turn off the motor if it overheats or an electrical fault occurs If this occurs let the pump motor cool for 15 minutes then press the manual reset button on the bottom of the motor and restart the motor DANGER Never run water through the filter system This will cause rust and corrosion in the motor and pump and will void the Warranty OIL DISPOSAL WARNING Always wear protective heat resistant gloves when performing the oil disposal operation If the cooking oil or shortening from a fryer is to be disposed follow steps 1 and 2 from Filtering Instructions in previous section Turn on the pump using the switch on the filter and direct the oil into an appropriate device such as an oil shuttle to move the used oil to its disposal tank L20 344 Rev 2 REPLACING THE FILTER PAPER If the filter paper becomes torn or if the time to filter the oil from one unit becomes excessive it is time to replace the Filter Envelope WARNING Only use filter paper envelopes from Anets that have been specifically designed for this filter system Using the wrong type of filter paper can cause damage to the pump system and will void the Warranty A DANGER A Make sure the filter pan has cooled completely to roo
Download Pdf Manuals
Related Search