DP 619 User Manual
Contents
1. 4 TEST CHANNELS 41 CH A You may select all or channel 1 6 using UP DOWN default A all channels 3 Press YES once the appropriate channel s will be fully on press YES twice the appropriate channel s will be half on press YES three times the appropriate channel s will go out 5 SET INPUTS 1 Tap UP DOWN to scroll to 5 SET INPUTS 5 SET INPUTS 2 Press YES the LCD shows Seer wees 51 DMX ONLY You may select DMX ONLY MAP ONLY using UP DOWN default DMX ONLY 3 Press YES to store your setting the LCD shows STORED OK 5 SET INPUTS Set up 6 UNIT SETUP 1 Tap UP DOWN to scroll to 6 UNIT SETUP 2 Press YES the LCD shows You may select MASTER SLAVE using UP DOWN default SLAVE 3 Press YES to store your setting the LCD shows 7 SET TEXT 1 Tap UP DOWN to scroll to 7 SET TEXT 2 Press YES the LCD shows You may change the blinking character using UP DOWN followed by YES When you ve finished the new text tap UP DOWN until END appears press YES to store the new text If you press YES without END the new text won t be stored into memory If you want to clear all these characters tap UP DOWN until CLR appears press YES the text will be cleared 6 UNIT SETUP 6 UNIT SETUP 61 SLAVE 6 UNIT SETUP STORED OK 7 SET TEXT 7 SET TEXT ABC A Set up 1 Tap UP DOWN to scroll t2. ELATION DP 619 6 CHANNEL DIGITAL DIMMER PACK USER S MANUAL Please read before use ELATION DP 619 6 CHANNEL DIGITAL DIMMER PACK Improvement and changes to specifications design and this manual may be made at any time without prior notice All rights reserved Contents Features 1 General Instructions 2 Overview 3 Front View 3 Rear View 5 Set up 7 Power Up 7 Menu System 7 SET DMX ADDRESS 8 SET CHANNELS 9 SET SCENES 12 TEST CHANNELS 16 SET INPUTS 16 UNIT SETUP 17 SET TEXT 17 SOFTWARE REV 18 READ INFO 18 OMONOAAKRWHD Additional Information 22 Fan Cooling 22 Over Temperature Solving 22 Master Slave Link Up 23 Lock the buttons 23 Technical Specifications 24 Features Thank you for your purchasing This product features include 6 DMX channels 24 map in DMX channels 24 programmable scenes 10 shows from 24 programmed scenes 90 built in chase programs Each channel can be programmed with preheat level 0 20 maximum output level 30 100 control curve linear square and switch and fade time 0 0s 999s Each scene can be programmed with the current output and fade time 24 map in DMX channels can be preset mapped to any of 10 scenes 10 shows and 90 chase programs DMX only and Map only can be selectable Several units can be linked in Master Slave mode Switch off protection in the event of over temperature LCD display
3. Celsius the LCD shows OVER TEMPERATURE and only 50 of output remains You may make RESET adjustment using menu 82 to resume normal output B When the recorded maximum temperature exceeds 70 Celsius and the ambient temperature is also over 70 Celsius the LCD shows OVER TEMPERATURE and only 50 of output remains You can not make any adjustments until over temperature is solved C In normal use whenever over temperature occurs the LCD should show OVER TEMPERATURE immediately and only 50 of output remains Additional Information Master Slave Link Up A You can set up communications between several units using Master Slave link up the first unit serves as the Master and the others are Slaves See menu 6 UNIT SETUP B The Master unit transfers the DMX signal and Map input signal to the Slave unit using DMX cables the Slave transfers the DMX input signal only but not the Map input signal Lock the buttons After power on the LCD shows general status and test messages Press and hold down YES and NO buttons simultaneously for three seconds the LCD should show L in the down right corner indicating all the buttons are locked Press the two buttons for three seconds again the L character disappears and the buttons are unlocked In menu 311 you may also lock or unlock the buttons as described above In menu 311 or 41 if you don t make any adjustments within 10 minutes the buttons should be locked automa
4. Power failure memory NOTE A knowledge of MIDI and DMX is required to fully utilize this unit General Instructions Please read through this operating instructions before installing or using your new product After you have finished reading the instructions put them away in a safe place for future reference N WARNING This product must be earthed To prevent fire or shock hazard do not expose this product under high temperature or moisture area Do not make any inflammable liquids water or metal objects enter the unit No user serviceable parts inside do not attempt repairs Should you product fail contact your local dealer N CAUTION This product is intended for indoor use only Provide occasional ventilation during use Disconnect the power when not use for extended period Do not use the unit in places subject to excessive humidity vibration or bumps Do not dismantle or modify the unit Overview 3 456 ELATION 0PL619 concinit oimmenrscr Overview 1 Circuit Breaker 16A 2 LCD Display Shows the current activities or adjustments of menus 3 UP Button Scroll through the menus or increase the values 4 DOWN Button Scroll through the menus or decrease the values 5 YES Button Enter a submenu or store the settings 6 NO Button Leave the settings unchanged or go back one level of the menus Overview DMX INPUT This connector ac
5. CENES 34 PRESET MAP ll Press YES the LCD shows 3 SET SCENES You may select channel 1 24using 341 CHANL 1 UP DOWN default CHANL 1 channel 1 Ill Press YES again the LCD shows 3 SET SCENES 3411 DO SCEN 1 You may select scene 1 24 show 1 10 program 1 90 using UP DOWN default SCEN 1 scene 1 IV Press YES to store your setting the LCD shows 3 SET SCENES STORED OK Set up 3 SET SCENES SET FADE TIME I Tap UP DOWN to scroll to the sub menu 35 FADE TIME the LCD shows 3 SET SCENES 35 FADE TIME ll Press YES the LCD shows 3 SET SCENES You may select all or scene 1 24 using 351 SCEN A UP DOWN default A all scenes lll Press YES again the LCD shows 3 SET SCENES 3511 TIME 0 0s You may select fade time 0 0s 999s using UP DOWN default 0 0s IV Press YES to store your setting the LCD shows 3 SET SCENES STORED OK NO DMX SCENE I Tap UP DOWN to scroll to the sub menu 36 NO DMX SCN the LCD shows 3 SET SCENES 36 NO DMX SCN ll Press YES the LCD shows 3 SET SCENES You may select scene 1 24 show 1 10 361 DO SCEN 1 program 1 90 using UP DOWN default DO SCEN 1 Ill Press YES to store your setting the LCD shows 3 SET SCENES STORED OK Set up 1 Tap UP DOWN to scroll to 4 TEST CHANLS 4 TEST CHANNELS 2 Press YES the LCD shows
6. DOWN default GO SCEN 1 play scene 1 Ill Press YES to store your setting the LCD shows S SET SCENES STORED OK Set up 3 SET SCENES RECORD Tap UP DOWN to scroll to the sub menu 32 RECORD the LCD shows 3 SET SCENES 32 RECORD ll Press YES the LCD shows 3 SET SCENES 321 GET SCEN 1 You may select Get scenes 1 24 Clear scenes using UP DOWN default 1 scene 1 Ill When you select Get scenes press YES to store your setting the LCD shows 3 SET SCENES STORED OK When you select Clear scenes press YES the LCD shows 3 SET SCENES ARE YOU SURE 3 SET SCENES ALL SCEN CLEARED Press YES again all scenes will be cleared the LCD shows DMX FAIL I Tap UP DOWN to scroll to the sub menu 33 DMX FAIL the LCD shows ll Press YES the LCD shows You may select LAST HELD ALL OFF SCENE 24 GO NO DMX GO MAP using UP DOWN default LAST HELD 3 SET SCENES 33 DMX FAIL 3 SET SCENES 331 LAST HELD Set up 3 SET SCENES DMX FAIL LAST HELD the last signal received is held in the outputs ALL OFF all channels go to zero output SCENE 24 scene 24 is output GO NO DMX menu 36 NO DMX SCN is recalled GO MAP map in signal is held in the outputs Ill Press YES to store your setting the LCD shows 3 SET SCENES STORED OK PRESET MAP I Tap UP DOWN to scroll to the sub menu 34 PRESET MAP the LCD shows 3 SET S
7. I When you select LOCK press YES the LCD shows ARE YOU SURE WANT TO LOCK IV If you are sure to lock press YES the LCD shows 9 READ INFO LOCK STORED OK If you are not sure press NO to go back V When the LCD shows 9 READ INFO 941 LOCKED If you want to unlock the menu tap UP DOWN the LCD shows PEASE PRES EY TO CONFIRM Keep pressing UP for 5 seconds tap DOWN once the LCD shows 9 READ INFO 941 LOCK Set up MENU ACCESS VI Use UP DOWN to scroll to UNLOCK press YES the LCD shows ARE YOU SURE WANT TO UNLOCK VII Press YES the LCD shows 9 READ INFO UNLOCK STORED OK If you are not sure press NO several times until the LCD shows DO YOU WANT TO EXIT then press YES to leave the setting unchanged SET DEFAULTS I Tap UP DOWN to scroll to the sub menu 95 SET DEFAULT the LCD shows 9 READ INFO 95 SET DEFAULT ll Press YES the LCD shows DO YOU WANT TO SET DEFAULTS Ill Press YES again the LCD shows ARE YOU SURE poro IV Press YES to set defaults to your dimmer Additional Information Fan Cooling The unit s fan is used to improve heat dissipation If the power is turned on the cooling fan will automatically run When the power is turned off it will stop Over Temperature Solving A When the recorded maximum temperature exceeds 70 Celsius and the ambient temperature is below 70
8. cepts DMX input signal MAP INPUT This connector is used to map in 24 DMX channel to control scene 1 24 show 1 10 or program 1 90 DMX OUTPUT This connector sends DMX signal through to the next DMX device Cooling Fan Terminal Output Power Input Single phase input or three phase input For details please refer to the wiring diagram printed on the top cover Overview Rear View BLOL LO0E2 Od NI OVA payues ag 3snu sngeuedde siy Burue anbunoaje 2042 ap anbsiu sed zauano N Buiuedp au0jag vemod andu yeuuossig NOLLNYID xoous 2 00912 JO YSIY pe12euuoo jaunoas aq JSNUI aim jeuynau indu eseud 38441 uSuA E SOUIM BIA paynould quoys aq 3snuu g7 27 V1 ndu eseud abuis uayM 2 pamoj e si 3ndui aseyd ajBuis Jo 3ndui auim unoy aseyd aauyy ayy 7H09 0S AOZL OV MN n I al ly aseyd Jed vzg 18301 ouueyo sad vat LNdLNO WEN Co a a oo Go N j d A j 7 N ejeg a 4 X punoJg L OG OD IT o7 1fndN ov 7H09 0S AOTL OV NEN 3 Ny z ES S9NIOGvO3 NOLLO3NNO9 3SVHd 33YHL f E EJ ino xwa V96 810L Jeuueuo Jed vaL Lnd1no NN O CBG QA QA HR KH i I A i d j d OO 00 000 o O 9 o o i O 9 n a 1 LMANI ov gua vun S9NIGvO3 Set up When power
9. is applied to your dimmer a self test is performed as indicated by its LCD The LCD reads DMX ABSENT DMX RECEIVED OK DMX SIGNAL ERROR or OVER TEMPERATURE After these initial test a text message begins to scroll through the LCD By default these messages are DIGITAL DIM PACK Menu System Tap the UP DOWN button to scroll through this menu system There are total 9 main menus the table below shows every main menu and also gives you an explanation 1 SET DMX ADDR 2 SET CHANNELS E w 3 SET SCENES 4 TEST CHANNELS YES v 9 READ INFO UP AA Scroll through Menu or increase the value DOWN wr Scroll through Menu or decrease the value FUNCTION 11 START ADDRESS 12 PATCH ADDRESS 21 SET PREHEAT 22 SET MAX OUT 23 SET CURVES 24 SET FADE TIMES 31 PLAY SHOW 32 RECORD 33 DMX FAIL 34 PRESET MAP 35 FADE TIMES 36 NO DMX SCENE 41 CH A Y TEST 51 DMX ONLY MAP ONLY 61 MASTER SLAVE 71 TEXT 81 REVISION 91 HOURS USED 92 TEMPERATURE 93 DMX LEVELS 94 MENU ACCESS 95 SET DEFAULTS YES y No X Start Channel 1 512 Individual Channel 1 512 All or 1 6 Channel 0 20 All or 1 6 Channel 3025 1009 Linear Square Switch All or 1 6 Channel 0 0s 999s Scene 1 24 Show 1 10 PROG 1 90 Get Scene 1 24 or clear all scene Last held All off Scene 24 Go no DMX Go MAP 1 24 Channel Scene 1 24 Show 1 10 or PROG 1 90 All or 1 24 Scene 0 0
10. led all or channel 1 6 using UP DOWN default A all channels 2 SET CHANNELS Ill Press YES again the LCD shows 2 SET CHANNELS 2311 CURVE LIN You may select desired curve mode using UP DOWN default Linear Use linear for normal dimming square for greater subtlety at the lower end and switch for ON OFF applications IV Press YES to store your setting the LCD shows 2 SET CHANNELS STORED OK SET FADE I Tap UP DOWN to scroll to the sub menu ou 24 SET FADE the LCD shows See CHANNELS 24 SET FADE ll Press YES the LCD shows You may select all or channel 1 6 using UP DOWN default A all channels 2 SET CHANNELS 241 CHANNEL A Set up 2 SET CHANNELS SET FADE lll Press YES again the LCD shows 2 SET CHANNELS 2411 0 0S You may adjust fade time within 0 0s 999s using UP DOWN default 0 0s IV Press YES to store your setting the LCD shows 2 SET CHANNELS STORED OK 3 SET SCENES 3 SET SCENES 2 Press YES to enter next menu level you may select 31 PLAY SHOW 32 RECORD 33 DMX FAIL 34 PRESET MAP 35 FADE TIMES 36 NO DMX SCENE using UP DOWN 1 Tap UP DOWN to scroll to 3 SET SCENES PLAY SHOW I Tap UP DOWN to scroll to the sub menu 31 PLAY SHOW the LCD shows SE SCENES 31 PLAY SHOW ll Press YES the LCD shows 3 SET SCENES 311 GO SCEN 1 You may select scene 1 24 show 1 10 program 1 90 using UP
11. nnel has a separate address 2 SET CHANNEL 1 Tap UP DOWN to scroll to 2 SET CHANNELS 2 SET CHANNELS 2 Press YES to enter next menu level you may select 21 SET PREHEAT 22 SET MAX OUT 23 SET CURVES 24 SET FADE TIME using UP DOWN SET PREHEAT I Tap UP DOWN to scroll to the sub menu 21 SET PREHEAT the LCD shows 2 SET CHANNELS 21 SET PREHEAT ll Press YES the LCD shows 2 SET CHANNELS You may select all or channel 1 6 y 211 CHANNEL A using UP DOWN default A all channels Set up Ill Press YES again the LCD shows 2 SET CHANNELS You may select desired value using 2111 075 UP DOWN default 0 IV Press YES to store your setting the LCD shows 2 SET CHANNELS STORED OK SET MAXIMUM OUTPUT I Tap UP DOWN to scroll to the sub menu 22 SET MAX OUT the LCD shows 2 SET CHANNELS 22 SET MAX OUT ll Press YES the LCD shows 2 SET CHANNELS 221 CHANNEL A You may select all or channel 1 6 using UP DOWN default A all channels Ill Press YES again the LCD shows You may select desired value using UP DOWN default 100 2 SET CHANNELS 2211 100 IV Press YES to store your setting the LCD shows 2 SET CHANNELS STORED OK Set up SET CURVES I Tap UP DOWN to scroll to the sub menu 23 SET CURVES the LCD shows 23 SET CURVES ll Press YES the LCD shows B T UMEN 231 CHANNEL A You may se
12. o 8 SOFTWARE REV 8 SOFTWARE REV 2 Press YES the LCD shows the software revision 8 SOFTWARE REV REV1 0 05 26 01 9 READ INFO 9 READ INFO 2 Press YES to enter next menu level you may select 91 HOUR USED 92 TEMPERATURE 93 DMX LEVEL 94 MENU ACCESS 95 SET DEFAULT using UP DOWN 1 Tap UP DOWN to scroll to 9 READ INFO HOUR USED I Tap UP DOWN to scroll to the sub menu 91 HOUR USED the LCD shows SEERDINEG 91 HOUR USED Il Press YES the LCD shows total hours used 9 READ INFO 911 00000 HOURS Set up 9 READ INFO TEMPERATURE I Tap UP DOWN to scroll to the sub menu A 92 TEMPERATURE the LCD shows 9 READ INFO 92 TEMPERATURE ll Press YES the LCD shows 9 READ INFO 921 MAX C You may select MAX MIN NOW temperature or RESET using UP DOWN lll When the LCD shows RESET press YES to reset the maximum and minimum temperature to now temperature DMX LEVELS I Tap UP DOWN to scroll to the sub menu 93 DMX LEVELS the LCD shows 9 READ INFO 93 DMX LEVELS ll Press YES the LCD shows 9 READ INFO 931 CH 1 XXX You may select channel 1 6 using UP DOWN Set up MENU ACCESS I Tap UP DOWN to scroll to the sub menu 94 MENU ACCESS the LCD shows 9 READ INFO 94 MENU ACCESS ll Press YES the LCD shows the default setting UNLOCKED You may select UNLOCK LOCK using UP DOWN EDER 941 UNLOCKED II
13. s 999s Scene 1 24 Show 1 10 or PROG 1 90 All or 1 6 Channel Test DMX MAP MASTER SLAVE ASCII 00000 99999 Hours Max Min Now Reset Channel 1 6 0 255 Unlock Lock Factory Settings Enter Sub Menu store settings or display information etc Go back one level of menu or leave setting Set up 1 SET DMX ADDRESS 1 Tap the UP DOWN button to scroll to 1 SET DMX ADDR 1 SET DMX ADDR 2 Press YES to enter next menu level Start Address and Patch Address are selectable using UP DOWN Start Address I Tap UP DOWN to scroll to the sub menu 11 START ADDR the LCD shows 1 SET DMX ADDR 11 START ADDR ll Press YES the LCD shows 1 SET DMX ADDR 111 START 1 111 Tap UP DOWN to select desired DMX address 1 512 for the start channel its default address is 1 IV Press YES to store your setting the LCD shows 1 SET DMX ADDR STORED OK Patch Address Tap UP DOWN to scroll to the sub menu 12 PATCH ADDR the LCD shows VSETDMX ADDR 12 PATCH ADDR ll Press YES the LCD shows 1 SET DMX ADDR 121 CHANNEL 1 You may select the desired channel using UP DOWN Ill Press YES again the LCD shows 1 SET DMX ADDR 1211 ADDR 1 Set up 1 SET DMX ADDR Patch Address IV Tap UP DOWN to select desired DMX Address 1 512 V Press YES to store your setting the LCD shows 1 SET DMX ADDR STORED OK VI Repeat steps II V until every DMX cha
14. tically you may press and hold down YES and NO buttons for three seconds to unlock the buttons and go on your setting In other menus if you don t make any adjustments within 10 minutes the buttons should be locked automatically the LCD shows the status messages and you should restart your menu adjustments Technical Specifications Power Input sees ee eee eee eee eee eee AC 120V 50 60Hz Channel Output Single phase 16A CH Total 96A Channel Output Three phases 16A CH Total 32A DMX Output eee 3 pin female XLR socket DMX Input see eee eee 3 pin male XLR socket Map Input see ee eee 3 pin male XLR socket Dimensions siinseid eain Ean 482x390x90mm Weight a ppro Mese m 9 0 kg C E ELA TION s 24 004 0636 Rev 1 0 August 2001 All rights reserved
Download Pdf Manuals
Related Search