Home

8920

1. 73 to the upper hole in the Front Upright 42 with an M10 x 97mm Bolt 16 an M10 Washer 9 and an M10 Nylon Locknut 21 Be sure that the small tabs on the Pulley Covers are on the side shown 11 Large 21 Attach the end of the Short Cable 23 to the Long U Bracket 57 with an M8 Nylon Locknut 3 and an M8 Washer 68 Do not completely tighten the Nylon Locknut it should be threaded onto the end of the Cable until two threads are showing above the Nylon Locknut as shown in the inset drawing SEAT ASSEMBLY 22 Attach the Backrest 41 to the Front Upright 42 with two M6 x 63mm Screws 43 and two M6 Washers 10 12 23 24 25 Press a 38mm Square Inner Cap 32 into the Seat Frame 36 Insert the M6 x 50mm Carriage Bolt 38 into the centre hole in the Seat Plate 37 Attach the Seat Plate to the Seat 13 with two M6 x 16mm Screws 18 Insert the M6 x 50mm Carriage Bolt 38 into the indicated hole in the Seat Frame 36 Tighten an M6 Nylon Locknut 2 with an M6 Washer 10 onto the Carriage Bolt Attach the other end of the Seat 13 to the Seat Frame 36 with an M6 Washer 10 and the M6 x 50mm Screw 24 Press a 38mm Square Inner Cap 32 into the Leg Lever 29 Lubricate the M8 x 57mm Bolt 33 Attach the Leg Lever 29 to the Seat Frame 36 with the Bolt and an M8 Nylon Locknut 3 Do not over ti
2. x 68mm Eyebolt Seat Frame Seat Plate Key No Qty bb WH HS HS SH HSH HSH B M M MM k HK KH AH M HNO WOK k M M OND AH HAH A k ac o R1101A Description M6 x 50mm Carriage Bolt Nylon Strap Seat Knob Backrest Front Upright M6 x 63mm Screw 45mm Square Inner Cap Large Foam Pad Press Arm Left Arm Right Arm 25mm Round Inner Cap Long Cable Trap 50mm Square Outer Cap Chain Cable Clip Lat Bar Top Frame Rear Upright Long U Bracket Long Cable M10 x 198mm Bolt Butterfly Arm Bushing Spring Clip 25mm Round Cover Cap 25mm Retainer M8 x 115mm Bolt 25mm Square Inner Cap Cable Trap Weight Stop M8 Washer M10 x 20mm Bolt Square Slider Bushing M10 x 45mm Bolt M8 x 67mm Bolt Pulley Cover User s Manual Note indicates a non illustrated part Specifications are subject to change without notice IMPORTANT PRECAUTIONS A WARNING To reduce the risk of serious injury read the following important precau tions before using the weight system 10 11 Read all instructions in this manual and in the accompanying literature before using the weight system Use the weight system only as described in this manual It is the responsibility of the owner to ensure that all users of the weight system are ade quately informed of all precautions The weight system is intended for home use only Do not use the weight system in a com mercial rental or institutional setting Use the weig
3. 08457 089 009 to order a free replacement decal Apply the decal in the indicated loca tion Misuse of this product may result in serious injury Read user s manual and follow all warnings and operating instruc tions prior to use Do not allow children on or around machine Replace label if damaged illegible or removed Keep hands and fingers clear of this area AWARNING Before beginning this or any exercise program consult your physician This is especially important for persons over the age of 35 or persons with pre existing health problems Read all instructions before using ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product BEFORE YOU BEGIN Thank you for selecting the versatile WEIDER 8920 weight system The WEIDER 8920 offers a selection of weight stations designed to develop every major muscle group of the body Whether your goal is to tone your body build dramatic muscle size and strength or improve your cardiovascular system the 8920 will help you to achieve the specific results you want For your benefit read this manual carefully before using the weight system If you have additional questions please call our Customer Service ASSEMBLED DIMENSIONS Height 193 cm Width 94cm Length 122 cm NOTES Department at 0845 089 009 To help us assist you please note the product model number and serial number before callin
4. NTS IMPORTANT PRECAUTIONS 0 0 0 0 ce nee eee 3 BEFORE YOU BEGIN a he Vid See d a dd US LN NA Ee Se e Eds baka 4 ASSEMBLY N R aon inl Gi aie Ah alae ER Ea aa ee al Sa eel E 5 ADJUSTMENT rca ds A one ee OGRE ab cate 15 WEIGHT RESISTANCE CHART ooo 17 TROUBLE SHOOTING AND MAINTENANCE 0 0 0 e tees 18 CABLE DIAGRAMS soii d wee a ihe eee Ped Se eae Sa eh e ad 19 PART EIST nn San dad a eS eee bine een EA 22 EXPLODED DRAWING x add ZR E E ia a baa al ht ead aa eke Saeed 23 ORDERING REPLACEMENT PARTS 0 0000 naaa Back Cover Note A PART IDENTIFICATION CHART is attached in the centre of this manual Remove the PART IDENTIFI CATION CHART before beginning assembly 23 EXPLODED DRAWING Model No WEEVSY97110 R1101A PART LIST Model No WEEVSY97110 Key No Qty OONDOOABRWND E AMM E MMM L HAR AHANHAWAWANMARANWWAAGQAN Description M8 x 63mm Carriage Bolt M6 Nylon Locknut M8 Nylon Locknut Base Stabiliser V Pulley M10 x 60mm Bolt Support Plate M10 Washer M6 Washer M8 x 70mm Bolt M10 x 50mm Bolt Seat M8 x 67mm Carriage Bolt 90mm Pulley M10 x 97mm Bolt Press Frame M6 x 16mm Screw Weight Carriage Pulley Bracket M10 Nylon Locknut M8 x 63mm Bolt Short Cable M6 x 50mm Screw M10 x 87mm Bolt 25mm Plastic Bushing 50mm Square Inner Cap Pad Tube Leg Lever Foam Pad Handgrip 38mm Square Inner Cap M8 x 57mm Bolt 19mm Round Inner Cap M10
5. ORDERING REPLACEMENT PARTS To order replacement parts contact the ICON Health amp Fitness Ltd office or write Unit 4 Revie Road Industrial Estate Revie Road Beeston Leeds LS118JG UK Tel 08457 089 009 Outside the UK 0 044 113 387 7133 Fax 0 044 113 387 7125 Please provide the following information when ordering replacement parts e the MODEL NUMBER of the product WEEVSY97110 e the NAME of the product WEIDER 8920 weight system the SERIAL NUMBER of the product see the front cover of this manual e the KEY NUMBER and DESCRIPTION of the part s see the PART LIST and EXPLODED DRAWING on pages 22 and 23 of this manual Part No 181135 R1101A Printed in China O 2001 ICON Health amp Fitness Inc Model No WEEVSY97110 Serial No Write the serial number in the space above for reference Serial Number Decal under seat QUESTIONS As a manufacturer we are committed to providing com plete customer satisfaction If you have questions or if there are missing or damaged parts please call 08457 089 009 Or write ICON Health amp Fitness Ltd Unit 4 Revie Road Industrial Estate Revie Road Beeston Leeds LS118JG UK email csuk iconeurope com 44 CAUTION Read all precautions and instruc tions in this manual before using this equipment Save this manual for future reference s Visit our website at Q www iconeurope com TABLE OF CONTE
6. PARTS on the back cover of this manual 18 ARM ASSEMBLY Press a 25mm Plastic Bushing 26 onto each welded spacer on the Press Frame 17 Slide the Press Frame onto the Base 4 so the Plastic Bushings are aligned with the indicated tube in the base Note This will be a tight fit the Plastic Bushings should fit over the ends of the tube in the Base Lubricate an M10 x 198mm Bolt 59 Attach the Press Frame 17 to the Base 4 with the Bolt two M10 Washers 9 and an M10 Nylon Locknut 21 Note Do not overtighten the Nylon Locknut the Press Frame must be able to pivot easily Press a 45mm Square Inner Cap 44 into the top of one of the Press Arms 46 Press a 25mm Round Inner Cap 49 into each end of the handle on the Press Arm Attach the Press Arm to one side of the Press Frame 17 with two M8 x 63mm Bolts 22 and two M8 Nylon Locknuts 3 Assemble the other Press Arm 46 in the same manner Identify the the Left Arm 47 and Right Arm 48 Note the position of the welded bracket on each Arm Arm identification is important for step 7 Press a Butterfly Arm Bushing 60 into each Arm Handle Welded Brackets Spacers o 44 49 7 Lubricate both axles on the Top Frame 55 WEIG HT RESISTANCE CHART Slide the Right Arm 48 onto the right axle of the Top Frame 55 Note Be careful not to con fuse the Right Arm with the Left Arm 47 refer to step 6 to iden
7. UM Di B NS ENN e MAA T MUM M6 Washer 10 M10 x 45mm Bolt 71 gd 25mm Round Inner Cap 49 R my M8 x 67mm Bolt 72 L T J no M8 x 70mm Bolt 11 a M10 Nylon Locknut 21 M10 x 50mm Bolt 12 50mm Square Inner Cap 27 O ANA M6 x 50mm Carriage Bolt 38 M8 x 67mm CarriageBolt 14 M8 O Locknut 3 ob e A P som AMM a 5 A y 45mm Square Inner Cap 44 M10 x 97mm Bolt 16 a gt i AN 19mm Round Inner Cap 34 25mm Square Inner Cap 65 N A a 38mm Square Inner Cap 32 pam 1 M10 x 198mm Bolt 59
8. e of the cables does not move smoothly find and correct the problem IMPORTANT If the cables are not properly routed they may be damaged when heavy weight is used See the CABLE DIAGRAM on page 19 of this manual for proper cable routing If there is any slack in the cables you will need to remove it by tightening the cables see TROUBLE SHOOTING AND MAINTE NANCE on page 18 14 17 18 19 20 Locate the Short Cable 23 Route the Short Cable through the bracket on the Press Frame 17 as shown Be sure that the Cable is rout ed over the crossbar Hold a 90mm Pulley 15 inside the bracket on the Press Frame 17 Attach the Pulley to the Press Frame with an M10 x 198mm Bolt 59 two M10 Washers 9 and an M10 Nylon Locknut 21 Wrap the Short Cable 23 around a 90mm Pulley 15 Attach the Pulley and a pair of Pulley Covers 73 to the lower hole in the Front Upright 42 with an M10 x 97mm Bolt 16 an M10 Washer 9 and an M10 Nylon Locknut 21 Be sure the small tabs on the Pulley Covers are on the side shown Wrap the Short Cable 23 around a 90mm Pulley 15 Attach the Pulley and a pair of Pulley Covers 73 to the upper hole in the Press Frame 17 with an M10 x 87mm Bolt 25 an M10 Washer 9 and an M10 Nylon Locknut 21 Make sure that the large tabs on the Pulley Covers are on the side shown Wrap the Short Cable 23 around a 90mm Pulley 15 Attach the Pulley and a pair of Pulley Covers
9. g The model number is WEEVSY97110 The serial number can be found on a decal attached to the weight system see the front cover of this owner s manual Before reading further please review the drawing below and familiarize yourself with the parts that are labeled High Pulley Station Lat Bar Backrest Seat Butterfly Arms Press Arm Weight Carriage Leg Lever Low Pulley Station Foot Plate 21 NOTES 20 ASSEMBLY Make Things Easier for Yourself Everything in this manual is designed to ensure that the weight system can be assembled suc cessfully by anyone However it is important to realize that the versatile weight system has many parts and that the assembly process will take time Most people find that by setting aside plenty of time assembly will go smoothly Before beginning assembly carefully read the following information and instructions e Assembly requires two people e Place all parts in a cleared area and remove the packing materials Do not dispose of the packing materials until assembly is completed e Tighten all parts as you assemble them unless instructed to do otherwise FRAME ASSEMBLY 1 Before beginning assembly be sure that you have read and understand the information in the box above Press a 50mm Square Inner Cap 27 into the end of the Base 4 Press a 50mm Square Outer Cap 51 onto each end of the Stabiliser 5 In
10. ghten the Nylon Locknut the Leg Lever must pivot freely Insert the M10 x 63mm Eyebolt 35 into the Leg Lever 29 from the direction shown Tighten an M10 Nylon Locknut 21 with an M10 Washer 9 onto the Eyebolt Note Be sure the Eyebolt is positioned vertically on the Leg Lever Rest the Seat Frame 36 on the indicated pin in the Front Upright 42 Attach the Seat Frame to the Front Upright with an M8 x 67mm Carriage Bolt 14 and the Seat Knob 40 S o Y ween ao V L N G x 2 Y f A NS O i 13 A CT V Pulley 6 Not shown to scale E ETA 90mm Pulley 15 Not shown to scale REMOVE THIS PART IDENTIFICATION CHART FROM THE MANUAL This chart is provided to help you identify the small parts used in assembly Important Some parts may have been pre assembled for shipping purposes if you cannot find a part in the parts bags check to see if it has been pre assembled Note Assembly is divided into four stages 1 frame assembly 2 arm assembly 3 cable assem bly and 4 seat assembly The hardware for each stage is packaged separately Wait until you begin each assembly stage to open that parts bag PART IDENTIFICATION CHART Model No WEEVSY97110 i Tit CUM R1101A M6 x 68mm Screw 43 O M MA 25mm Round Cover Cap 62 M10 x 20mm Bolt 69 C BRT AMAA Ei D C
11. h an M10 x 45mm Bolt 71 and an M10 Nylon Locknut 21 Be sure that the Cable is in the groove of the Pulley and that the Cable and Pulley move smoothly ATTACHING THE LAT BAR OR NYLON STRAP TO A PULLEY STATION 16 Attach the Long Cable 58 to the Weight Carriage 19 with an M10 x 20mm Bolt 69 and an M10 Nylon Locknut 21 Attach the Lat Bar 54 to the Long Cable 58 with a Cable Clip 53 For some exercises the Chain 52 should be attached between the Lat Bar and the Long Cable with two Cable Clips Adjust the length of the Chain between the Lat Bar and the Long Cable so the Lat Bar is in the correct starting position for the exercise to be performed The Nylon Strap not shown can be attached in the same manner The accessories can be attached to the Short Cable not shown in the same manner 10 15 26 27 Press two 19mm Round Inner Caps 34 into the ends of both Pad Tubes 28 Insert one Pad Tube 28 into the Seat Frame 36 Slide a Foam Pad 30 onto each end of the Pad Tube Insert the other Pad Tube 28 into the Leg Lever 29 Slide a Foam Pad 30 onto each end of the Pad Tube Make sure that all parts have been properly tightened The use of all remaining parts will be explained in ADJUSTMENT beginning on page 15 of this manual Before using the weight system pull each cable a few times to make sure that the cables move smoothly over the pulleys If on
12. hort Cable 23 42 with two M8 x 67mm Bolts 72 a Support Plate 8 and two M8 Nylon Locknuts 3 Attach the Top Frame to the Rear Upright 56 in the same manner Tighten the Nylon Locknuts 3 used in steps 1 3 Weight Carriage 8 O 1 Low Pulley TROUBLE SHOOTING AND MAINTENANCE Make sure all parts are properly tightened each time you use the weight system Replace any worn parts immedi ately The weight system can be cleaned using a damp cloth and mild non abrasive detergent Do not use solvents TIGHTENING THE CABLES Woven cable the type of cable used on the weight system can stretch slightly when it is first used If there is slack in the cables before resistance is felt the cables should be tightened Slack can be removed from the Short Cable 23 by tightening the M8 Nylon Locknut 3 at the end of the Cable Additional slack can be removed by moving the 90mm Pulley 15 to the other hole in the Long U Bracket 57 Remove the M10 Nylon Locknut 21 and the M10 x 50mm Bolt 12 from the Pulley Covers 73 the Pulley and the U Bracket Re attach the Pulley and the Pulley Covers to the other hole in the U Bracket with the Bolt and Nylon Locknut Make sure that the Cable and Pulley move smoothly Note If a cable tends to slip off the pulleys the cable may have become twisted Remove the cable and re install it If a cable needs to be replaced see ORDERING REPLACEMENT
13. ht system only on a level sur face Cover the floor or carpet beneath the weight system to protect the floor Make sure all parts are properly tightened each time the weight system is used Replace any worn parts immediately Keep children under the age of 12 and pets away from the weight system at all times Keep hands and feet away from moving parts Always wear athletic shoes for foot protec tion when using the weight system The weight system is designed to support a maximum user weight of 114 kg 250 Ibs Do not place more than 57 kg 125 Ibs on the weight carriage Never release the press arm butterfly arms leg lever lat bar or nylon strap whilst weights are raised the weights will fall with great force Make sure that the cables remain on the pul leys at all times If the cables bind whilst you are exercising stop immediately and make sure that the cables are on all of the pulleys 12 Always stand on the foot plate when per forming an exercise that could cause the weight system to tip 13 Always disconnect the lat bar from the weight system when performing an exercise that does not use the lat bar 14 If you feel pain or dizziness at any time whilst exercising stop immediately and begin cooling down 15 The decal shown below has been placed on the weight system in the indicated location If the decal is missing or illegible please call our Customer Service Department toll free at
14. ly If the cables have not been correctly routed the weight system will not function properly and damage may occur The numbers show the correct route for each cable The starting and ending points of each cable are labeled The small draw ings show the correct position of each cable trap Make sure that the cable traps do not touch or bind the cables Turn the Weight Stop 67 so that the indicated hole is on the side shown and the Square Slider Bushing 70 is on top Slide the Weight Stop onto the Rear Upright 56 Refer to drawing 2b Attach the Weight Stop 67 to the Rear Upright 56 with an M8 x 70mm Bolt 11 and an M8 Nylon Locknut 3 7 1 High Pulley fr 3 S o Long Cable 58 4 TOP VIEW Orient the Weight Carriage 19 as shown Slide the Weight Carriage onto the Rear Upright 56 Press a 25mm Square Inner Cap 65 into the Front Upright 42 Slide the Front Upright onto the M8 x 63mm Carriage Bolts 1 in the Base 4 Hand tighten an M8 Nylon Locknut 3 onto each Carriage Bolt Do not tighten the Nylon Locknuts yet AD 5 Long U Bracket 3 Press a 50mm Square Inner Cap 27 into the top of the Rear Upright 56 Press a 45mm Square Inner Cap 44 into each end of the crossbar on the Top Frame 55 Press two 25mm Round Inner Caps 49 into the top of the crossbar Attach the Top Frame 55 to the Front Upright S
15. mm Pulley 15 Attach the Pulley and a pair of Pulley Covers 73 to the upper hole in the Long U Bracket 57 with an M10 x 50mm Bolt 12 and an M10 Nylon Locknut 21 Be sure that the large tabs on the Pulley Covers are on the side shown ADJUSTMENT The instructions below describe how each part of the weight system can be adjusted IMPORTANT When attaching the lat bar or nylon strap make sure that the attachments are in the correct starting position for the exercise to be performed If there is any slack in the cables or chain as an exercise is performed the effectiveness of the exercise will be reduced ADDING WEIGHTS TO THE WEIGHT CARRIAGE To add resistance to your workout slide an equal amount of weight not included onto each side of the weight tube on the Weight Carriage 19 Make sure that the weights are pushed against the stops Secure the weight with two Spring Clips 61 Note Due to the cables and pulleys the actual amount of resistance at each exercise station may vary from the amount of weight used Use the WEIGHT RESISTANCE CHART on page 17 to find the actu al amount of resistance at each weight station A WARNING bo not place more than 57 kg 125 Ibs on the weight carriage Always secure the weight on the Weight Carriage 19 with two Spring Clips 61 15 Route the Long Cable 58 around a 90mm Pulley 15 Attach the Pulley to the bracket on the Top Frame 55 wit
16. ng Cable 58 Route the Long Cable around a 90mm Pulley 15 Attach the Pulley and two Pulley Covers 73 to the Top Frame 55 with an M10 x 97mm Bolt 16 and an M10 Nylon Locknut 21 Note The small tabs on the Pulley Covers must be on top Be sure that the Cable is between the Pulley and the rod on the Top Frame and that the end of the Cable with the ball is on the indicated side of the Rod ATTACHING AND REMOVING THE SEAT Set the bracket on the Seat Frame 36 onto the pin on the Front Upright 42 Attach the Seat Frame to the Front Upright with the M8 x 67mm Carriage Bolt 14 and the Seat Knob 40 For some exercises the Seat 13 must be removed First be sure that the chain is not attached to the leg lever Next remove the Seat Knob 40 and the M8 x 67mm Carriage Bolt 14 from the Seat Frame 36 Lift the Seat Frame off the Front Upright 42 ATTACHING THE LEG LEVER TO THE LOW PULLEY STATION To use the Leg Lever 29 the seat must be attached to the front upright see ATTACHING AND REMOV ING THE SEAT above Attach one end of the Chain 52 to the M10 x 68mm Eyebolt 35 with a Cable Clip 53 Attach the other end of the Chain to the Short Cable 23 with a Cable Clip Note Be sure the Eyebolt is positioned verti cally on the Leg Lever 16 10 11 12 13 Wrap the Long Cable 58 around a V Pulley 6 Attach the Pulley and a Long Cable Trap 50 to the bracket on the Fro
17. nt Upright 42 with an M10 x 60mm Bolt 7 and an M10 Nylon Locknut 21 Be sure that the Cable Trap is positioned to hold the Cable in the groove of the Pulley Route the Long Cable 58 around a V Pulley 6 Attach the Pulley and a Long Cable Trap 50 to the Left Arm 47 with M10 x 60mm Bolt 7 and an M10 Nylon Locknut 21 Be sure that the Cable is in the groove of the Pulley and that the Cable Trap is positioned to hold the Cable in place Route the Long Cable 58 around a V Pulley 6 Attach the Pulley and the Long Cable Trap 50 to the Right Arm 48 with an M10 x 60mm Bolt 7 and an M10 Nylon Locknut 21 Be sure that the Cable is in the groove of the Pulley and that a Long Cable Trap 50 is turned to hold the Cable in place Refer to the inset drawing Attach the Pulley Bracket 20 to the bracket on the Top Frame 55 with an M8 x 115mm Bolt 64 and an M8 Nylon Locknut 3 Note The Pulley Bracket is pre assembled with a 90mm Pulley 15 and a Cable Trap 66 Route the Long Cable 58 around the 90mm Pulley 15 attached to the Pulley Bracket 20 Be sure that the Cable is in the groove of the Pulley and that the Cable Trap 66 is turned to hold the Cable in place Make sure that the M10 x 50mm Bolt 12 securing the Pulley and Cable Trap to the Pulley Bracket is properly tight ened and that the Pulley Bracket can pivot freely 14 Wrap the Long Cable 58 around a 90
18. sert two M8 x 63mm Carriage Bolts 1 up through the Base 4 Insert two M8 x 67mm Carriage Bolts 14 up through the Stabiliser 5 Note Be sure the indents around the holes in the Stabiliser are on the bottom Slide the bracket end of the Base 4 onto the M8 x 67mm Carriage Bolts 14 in the Stabilizer 5 Slide the Rear Upright 56 onto the Carriage Bolts Hand tighten an M8 Nylon Locknut 3 onto each Carriage Bolt s As you assemble the weight system make sure all parts are oriented as shown in the drawings s For help identifying small parts use the PART IDENTIFICATION CHART in the centre of this manual The following tools not included are required for assembly s two adjustable spanners one rubber mallet one standard screwdriver one Phillips screwdriver lubricant such as grease or petroleum jelly and soapy water Assembly will be more convenient if you have a socket set a set of open end or closed end wrenches or a set of ratchet wrenches Indents 2 Refer to drawing 2a Press a 25mm Round Inner Cap 49 into each end of the weight tube on the Weight Carriage 19 Note Make sure the Square Slider Bushings 70 are assembled to the Weight Carriage and Weight Stop 67 CABLE DIAGRAM The cable diagram below shows the proper routing of the Short Cable 23 and the Long Cable 58 Use the diagram to be sure that the two cables and the cable traps have been assembled correct
19. tify the Right Arm Be sure that the upper end of the Right Arm is behind the indicated bracket on the Top Frame This chart shows the approximate weight resistance at each weight station The column labeled WEIGHT refers to the amount of weight in pounds placed on the weight carriage The weight resistance shown for the butterfly arm station is for each butterfly arm Note The actual resistance at each station may vary due to friction between the cables pulleys and weight carriage WEIGHT PRESS ARM BUTTERFLY ARM LOW PULLEY HIGH PULLEY Ibs Ibs LEG LEVER Ibs Ibs Tap two 25mm Retainers 63 and a 25mm Round Cover Cap 62 onto the right axle of the Top Frame 55 Be sure that the teeth on the Retainers bend toward the Cover Cap as shown in the inset drawing Attach the Left Arm 47 in the same manner Press two 45mm Square Inner Caps 44 into the lower ends of the Left and Right Arms 47 48 Wet the lower end of each Arm with soapy water Slide a Large Foam Pad 45 onto the lower end of each Arm CABLE ASSEMBLY 8 During steps 9 through 22 refer to the CABLE DIAGRAM on page 19 of this manual to verify proper cable routing Before beginning this sec tion identify the Short Cable 23 and the Long Cable 58 by comparing the ends of the cables IMPORTANT Whilst assembling the cables do not overtighten the bolts and nuts securing the pulleys The pulleys must turn freely 9 Locate the Lo

8920

Contents

Download Pdf Manuals

Related Search

Related Contents