Untitled - PLANET Technology Corporation.
Contents
1. 9 4 5 Link Fault Pass through LFP The LFP function includes the Link Fault Pass Through function LLCF LLR and the DIP Switch design LLCF LLR can immediately alarm administrators the problem of the link media and provide efficient solution to monitor the net The DIP Switch provides disable or enable the LFP function LLCF Link Loss Carry Forward means when a device connected to the converter and the TP line loss the link the converter s fiber will disconnect the link of transmit LLR Link Loss Return means when a device connected to the converter and the fiber line loss the link the converter s fiber will disconnect the link of transmit Both can immediately alarm administrators the problem of the link media and provide efficient solution to monitor the net Link Loss Carry Forward LLCF FTP 80X incorporates an LLCF function for troubleshooting a remote connection When LFP function is enabled the FL TP ports do not transmit a link signal until they receive a link signal from the opposite port The diagram below shows a typical network configuration with a good link status using FTP 80X for remote connectivity Management Switch Hub Media Media Switch Hub Management Station w SNMP Converter Converter w SNMP Station LFP ON LFP ON Fiber cai 0 LED lit established link LED unlit no link If the connection breaks FTP 80X that link loss forw2. 802515 Rev 1 0 March 2008 Part No 2350 AA3540 000 Table Of Contents 1 Overview RR 6 2 Model MH EE y B CHECKS E 7 4 Product Outlook ci ag i tentare nee a Fo e 8 5 Link Fault Pass through uuu isa rh anu RR E vos 10 6 Installing the 13 14 8 LED indiCatlOTi erint three pnta p h pe pase ene p 15 9 Cable Connection Parameter 16 10 FTP 80X Technical 17 APPENDIX A 18 A 1 Device s RJ 45 Pin 18 2 RJ 45 cable pin 18 Fiber Optical Cable Connection Parameter 19 1 Overview Thank you for purchasing PLANET FTP 80X family 10 100Mbps Ethernet Twisted pair to 100 Fiber optic PoE Bridge Converter This converter is used to convert one type media signal to other type equivalent that allows two type segments connect easily efficiently and inexpensively The converter provides Power over Ethernet power injector function which is able to drive one IEEE 802 3af compliant powered devices About the Power over Ethernet Injector The FTP 80X is an IEEE 802 3af Power over Ethernet Injector that provide DC 48V over Ethernet cables The
3. Position Title Product Manager Taiwan 15 March 2008 Hud bey Place Date Legal Signature PLANET TECHNOLOGY CORPORATION e mail sales planet com tw _http www planet com tw 11F No 96 Min Chuan Road Hsin Tien Taipei Taiwan R O C Tel 886 2 2219 9518 Fax 886 2 2219 9528 Q PLANET PLANET Technology Corp C e 2350 AA3540 000
4. 151S 1525 with Internet Camera ICA 210 or Wireless Access Point WAP 4060PE installed in the wild rang place 2km 15km 100 meters FTP 80x Data Data Power Fiber Switch PoE Wireless AP 4 14 8 LED indication W System LED Color Function PWR Green Lit Indicate the device is powered m 10 100Base TX Port LED Color Function Indicate that the Media Converter Blink is actively sending or receiving data LNK ACT Green over that port Lit Indicate that the port is link up Off Indicate that the port is link down Lit Indicate that the port is providing PoE in 48VDC to remote powered device Green Use Indicate that the port is not providing or 48VDC to remote powered device m 100Base FX SC Port LED Color Function Indicate that the Media Converter Blink is actively sending or receiving data LNK ACT Green over that port Lit Indicate that the port is link up off Indicate that the port is link down Fiber optic Partner should be set to the correct mode according to this FDX indicator for optimal network performance 15 H 9 The limitations are as below Duplex Connection Limitation max Twisted Pair Node to Node Half Full Node to Switch Hub 100 meters Multi Mode Converters Node to Node MM Half Nod
5. FTP 80X IEEE 802 3af Power over Ethernet Injector inserts DC Voltage into Cat 5 cable allowing the cable between the Injector FTP 80X and PoE PD Powered Device to transfer data and power simultaneously The maximum distance between the Injector FTP 80x and PoE PD is 100 meters With FTP 80x installed it is combines the Ethernet digital data with power over the twisted pair cables as an IEEE 802 3af Power over Ethernet Injector And the IEEE 802 3af Power over Ethernet splitter shall separate the digital data and the power into two outputs With IEEE 802 3af Power over Ethernet devices installed the System administrator only have to use a single RJ 45 Ethernet cable to carries both power and data to each devices Besides to connect through FTP 80x and PoE PD you could also have following benefit that cost saving easy for networking planning and higher reliability What s more upon any IEEE 802 3af devices installed the FTP 80X or PD all can make the connection while migrating and the Ethernet digital packets such as connecting the FTP 80X to an IEEE 802 3af complied devices AP or IP Camera 2 Model List Your PoE Media Converter comes with two of the following models FTP 802 on board SC Multi mode fiber connector up to 2km FTP 802S15 on board SC Single mode fiber connector up to 15km In the following sections the term FTP 80X indicates the product family above 3 Checklist Your FTP 80X carto
6. Networking amp Communication PoE 100Base FX to 10 100Base TX FTe80XSeries POE Media Converter User s Manual 100Base FX to 10 100Base TX PoE Media Converter FTP 80x User s Manual Trademarks Copyright PLANET Technology Corp 2008 Contents subject to revision without prior notice PLANET is a registered trademark of PLANET Technology Corp The information in this manual is subject to change without notice All other trademarks belong to their respective owners Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications and makes no warranty and representation either implied or expressed with respect to the quality performance merchantability or fitness for a particular purpose PLANET has made every effort to ensure that this User s Manual is accurate PLANET disclaims liability for any inaccuracies or omissions that may have occurred Information in this User s Manual is subject to change without notice and does not represent a commitment on the part of PLANET PLANET assumes no responsibility for any inaccuracies that may be contained in this User s Manual PLANET makes no commitment to update or keep current the information in this User s Manual and reserves the right to make improvements to this User s Manual and or to the products described in this User s Manual at any time without notice If you find information in this manual that
7. ard to the switch hub that generates a trap to the management station _4 10 The administrator can then determine the source of the problem Management Switch Hub Media Media Switch Hub Management Station w SNMP Converter Converter w SNMP Station LFP ON LFP gt q de Broken Ore Fier e e 1 LED lit established link LED unlit link Units are shipped with the LFP function disable OFF Link Loss Return LLR The fiber ports of FTP 80X have been designed with an LLR function for troubleshooting a remote connection LLR works in conjunction with LLCF When LFP function is enabled the port s transmitter shuts down when its receiver fails to detect a valid receive link LLR should only be enabled on one end of the link and is typically enabled on either the unmanaged or remote device The diagram below shows a typical network configuration with a good link status using FTP 80X for remote connectivity Note that LLR and LLCF are enabled as indicated in the diagram Management Switch Hub Media Media Station w SNMP Converter Converter LFP ON LFP OFF gt 4 Switch Hub Station Fiber LED lit established link LED unlit no link 11 41 If one of
8. e to Switch 412 meters Ki ro Neves Node FTP 802 2 kilometers Node to Swi tch Single Mode Converters Node to Node tch aM Full Node to Swi FTP 802S15 15 kilometers 10 FTP 80X Technical Specifications The FTP 80X comes with the following standard features Standard IEEE 802 3u 10 100Base TX 100Base FX EEE 802 3af Power over Ethernet Connectors W One 45 Auto MDI MDI X Twisted Pair EIA568 with PoE W One Fiber optic 1310nm wavelength connector type vary with model Data Transfer Rate 10 100Mbps TP 100Mbps FX Duplex mode support Full or half duplex mode by Auto Negotiation TP LED indicators PWR FX LNK ACT TX LNK ACT PoE in Use PoE Power Output 48V DC Max 15 4 watts 350mA Power Pin Assignment 1 2 3 6 End Span Power Supply 48V DC 0 4A external AC DC adapter Ambient Temperature 0 to 50 C operating Humidity 596 to 9096 non condensing Dimension 26 x 70 x 97mm H x W x D Cable W UTP Cat 5 UTP cable W Fiber MM 50 125 um or 62 5 125 um optic fiber W Fiber SM 9 125 um optic fiber Connecting to Router Bridge or Switch Hub please refer to the device s Technical Manual 171 Device s RJ 45 Pin Assignments m 10 100Mbps 10 100Base TX Contact MDI MDI X 1 1 TX 3 2 2 6 3 3 RX 1 6 6 RX 2 4 5 7 8 Not used Not used Implicit implementation of the crossover f
9. is incorrect misleading or incomplete we would appreciate your comments and suggestions FCC Warning This equipment has been tested and found to comply with the regulations for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with this user s guide may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense CE Mark Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures WEEE Warning To avoid the potential effects on the environment and human health as result the presence of hazardous substances in electrical and electronic equipment end users of electrical and electronic equipment should understand the meaning of the crossed out wheeled bin symbol Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately Revision User s manual for PLANET 100Base FX to 10 100Base TX PoE Media Converter Multi mode FTP 802 Single mode
10. n should contain the following items 100Base FX to 10 100Base TX PoE Media Converter x 1 AC DC Power Adapter Input 48V DC 0 4A max x 1 User s Manual x 1 If any item is missing or damaged please consult the dealer from whom you purchased your PoE Media Converter 7 Y 4 Product Outlook Overview The layout of FTP 802 is the same as for FTP 802515 Rear Panel NO 340 eo L 9a ti E x i 5 We n 5 x s ez E 8 S cw e To l00Base TX x mox tege oos OO PoE Media Converter PWR MU Ethernet DC 10 100Base TX to I00Base FX Front Panel Left View There are one 45 Twisted Pair jack Auto MDI MDI X one fiber optic connector vary by model and four LED indicators TX RX ed 4 90 PoE Media Converter 10 100Base TX to 100Base FX FX TP PWR PoE In Use LNK ACT 10 100Base TX Right View One DIP switch for Link Fault Pass Through LFP feature ON to turn on the LLCF and LLR detection And OFF to turn off this feature Please refer to the following sections for more Also one DC 48V power socket for the PoE Media Converter 48V DC oco OFF LFP ON
11. ommunication EC Declaration of Conformi For the following equipment Type of Product LOOBase FX to 10 100Base TX PoE Media Converter Model Number FTP 802 FTP 802S15 Produced by Manufacturer s Planet Technology Corp Manufacturer s Address No 96 Min Chuan Road Hsin Tien Taipei Taiwan R O C is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive on 89 336 EEC For the evaluation regarding the EMC the following standards were applied Emission EN 55022 1994 A1 1995 2 1997 Class A Harmonic EN 61000 3 2 2000 Flicker EN 61000 3 3 1995 A1 2001 Immunity EN 55024 1998 ESD TEC 61000 4 2 1995 A1 1998 A2 2000 RS 61000 4 3 1995 A1 1998 A2 2000 EFT Burst TEC 61000 4 4 1995 A1 2000 Surge TEC 61000 4 5 1995 A1 2000 cs TEC 61000 4 6 1996 A1 2000 Magnetic Field TEC 61000 4 8 1993 A1 2000 Voltage Disp TEC 61000 4 11 1994 A1 2000 Responsible for marking this declaration if the DX Manufacturer Authorized representative established within the EU Authorized representative established within the EU if applicable Company Name Planet Technology Corp Company Address No 96 Min Chuan Road Hsin Tien Taipei Taiwan R O C Person responsible for making this declaration Name Surname Kent Kang
12. tach a Cat 5 UTP cable from the 10 100Base TX network to the RJ 45 port on the FTP 80X Connect the 48V DC power adapter to the FTP 80X and verify that the Power LED lights up Turn on the power of the device station the TX Link and FX Link LEDs should light when all cables are attached FTP 80X 100Base FX Fiber Network 10 100Base TX Cat 5 5e TP Cable Network RJ 45 STP UTP Cat 5 straight crossover cable is accepted Please refer to section 9 for more about the wiring distance of your TP Optic fiber networks 18 7 PoE function FTP 80X and the IEEE 802 3af Injector Splitter equipment installation Before your installation it is recommended to check your network environment If there is any IEEE 802 3af devices need to power on the FTP 80X can provide you a way to supply power for this Ethernet device conveniently and easily The FTP 80X equips with an AC DC adapter with DC 48V input and injects this DC power into the pin of the twisted pair cable pair 1 2 and pair 3 6 If there is very difficult to find a power socket for AC DC Adapter of your non IEEE 802 3af networked device the FTP 80X and 1515 1525 can provide you a way to supply DC power for this Ethernet device conveniently and easily For the places hard to find the power inlet the FTP 80X provide the easiest way to power your Ethernet devices such as PLANET IEEE 802 3af Power over Ethernet Splitter POE
13. the optical conductors is bad as shown the diagram box below the converter with LLR function will return a no link condition to its link partner With LLCF function also enabled the no link condition is carried forward to the switch hub where a trap is generated to the management station and the administrator can then determine the source of the loss Management Switch Hub Media Media Management Station w SNMP Converter Converter Switch Hub Station LFP ON LFP ON gt 4 Brok Ore Or O evo e e 1 Port 2 Port 1 1 Link Loss Carried Forward Link Loss Carried Forward Link Loss Returned LED lit established link LED unlit no link LFP function is turn off in default This feature can also be turned on via the side DIP switch If you are not familiar with the network installa tion and for diagnostic purpose i e check which end is broken you can turn it on and reset the converter to make it take effect Otherwise please remain it in the default position 412 6 Installing the Converter Please follow these steps to install the PoE Media converter Turn off the power of the device station in a network to which the FTP 80X will be attached Ensure that there is no activity in the network Attach fiber cable from the FTP 80X to the fiber network TX RX must be paired at both ends At
14. unction within a twisted pair cable or at a wiring panel while not expressly forbidden is beyond the scope of this standard A 2 RJ 45 cable pin assignment There are 8 wires on a standard UTP STP cable and each wire is color coded The following shows the pin allocation and color of DD 2 straight cable and crossover cable connection Straight Cable SIDE 1 12345678 SIDE1 1 White Orange 2 Orange 3 White Green 4 Blue 5 White Blue 12345678 SIDE2 6 Green 7 White Brown 8 Brown SIDE 1 SIDE2 6 Green 7 White Brown 8 Brown SIDE1 1 White Orange 78 2 Orange 3 White Green 4 Blue 5 White Blue 78 SIDE 2 1 White Orange 2 Orange 3 White Green 4 Blue 5 White Blue 6 Green 7 White Brown 8 Brown SIDE2 1 White Green 2 Green 3 White Orange 4 Blue 5 White Blue 6 Orange 7 White Brown 8 Brown Figure A 1 Straight Through and Crossover Cable Please make sure your connected cables are with same pin assignment and color as above picture before deploying the cables into your network A 3 Fiber Optical Cable Connection Parameter The wiring details are as below m Fiber Optical patch Cables Standard Fiber Type Cable Specification 100Base FX 1310nm Multi mode 50 125um 62 5 125um 100Base FX 1310nm Single mode 9 125um 19 GQ PLANET Networking amp C
Download Pdf Manuals
Related Search