Please read this instruction manual carefully, and
Contents
1. Foard ie STRETE Support Tool GReddy e Manage Support Tool vi t instruction Manual Please read this instruction manual carefully and proceed with the installation ONLY if you fully understand this manual_ Make sure to pay attention to all the Important Warning and Caution messages through out the manual Important D This product is legal for sale or use in California only on vehicles which may never be driven on a public highway O This product is only for vehicles with 12V battery systems Warning 0 Installation and use of this product should only be performed by a trained specialist who is very familiar with the automobile s mechanical electrical and fuel management systems if installed by untrained person it may cause damage to the unit as well as the vehicle O When using a soldering iron or other tools for installation make sure you read and understand the tool s user manual Mis use of these tools can cause serious injuries DO Never tune the E manage while the vehicle is moving O Never tune the e Manage on public highways This can be dangerous to you and others on the road O When tuning and operating the vehicle in a garage make sure that the garage is equipped with a proper ventilation system O After installation and tuning make sure to clean up every thing that would interfere the driver Wres tools and laptop computer may interfere with the driver and cause accidents O Av2. Und 3 injector signal wire Engine Contra Una Sptica i PR JOHA 4i Z 3 CH 3 Ras JTH2 BL AG J O1 BR VJ Ground Yetlow Red OR Cranga Red BLAR Blue Red PIR Purple Red YR PVR Pink Red LBYR Light Blue Red B R Black Red O If the vehicle does not have the same nunber of injector signal wire as the number of the engine s cylinder number group 2 wires in to one See the diagram above Diag ifi Wre diagram for Sub Injector Signal O When using the I J CH A I J CH B for sub injectors set the jumper J P5 and J P6 in the e manage main unit to 1 2 from Open For low resistance mjectors p kog aaa mu UD GPA Or QB onnar ea T Fuse For high resistance injectors a GHA or CH B aiam Arlt Sater Banery pane nportant O If the vehicle does not have the sane nunber of injector signal wire as the nurrber of the engine s cylinders group 2 wires in to one Wre diagram for Ignition Signal Please read the instructions included with the Ignition Harness Kit and proceed with the wring only if you fully understand the instructions O Connect to the vehicle s ignition signal wires Refer to the ECU wire location chart in this manual for the proper location of each wire O Connect the ignition channel wire in the engine s firing order So ICE 3 4 6 8 cylinder distributor Ce ae ae a Inline 4 cylinder group ignition aaja O Horizontally opposed 4 cylinder Pez eff roe
3. omelets WT Horizontally opposed 4 cylinder t1 ejeje seje T Intine 6 cylinder group ignition tt 6 V6 group ignition t1 4 Inline 6 cylinder individual ignition t1 te it V6 individual ignition tl t2 t3 t4 t5 t6 13B FC3S JC3SE tT tl aeea a 13B FD3S Fetijerzfe Important O Make sure that wires are connected in the firing order and jumper setting is correct Improper wiring and setting can darmage the ignition coil Example 2 NA6CE ECU 40 1 group Ignition H Male connactor 4 Female connector Spl o Example 1 BNR32 ECU indine 6cyl individual ignition Example 2 AE111 ECU Disvibutor ignition Control Unit A Mala connector Female connector Splice a BUWICHT NY On Honda EG type vehicles the bottom third pin fromthe right on the 26 pin is also an ignition signal Group the 2 wire together Important O On Honda set the junper pins J P 1 and J P2 to 2 3 O After wiring if the tachorreter or not firing occurs set the jumper pin J P2 to 2 3 especially on Toyotas 10 T Before yot Starting the application 1 With the IG key in OFF position connect the PC and e Manage using the Communication Cable D Sub 9pin connector to PC and USB to the e Manage 2 Turn the IG key to the ON position then double click on the e Manage short cut icon on tile desktop 3 When the application opens
4. ROM x1 wate Fa Support Toot i imam 6 0 Instruction Manual x 1 Conmunication Cable x 1 This product will allow the tuner to program GReedy e Manage functions by linking the e Manage and a WindowsRQ based PC This product is only for the vehicles equipped with GReddy e Manage Features D Air Flow Adjustment Map This 16 xl6 rpm x throttle position table is used to fine tune the input signal of the Air Flow Meter or MAP Sensor to the ECU for fuel enrichment O Upgrade Injectors Controls upgrade injectors up to 150 larger than factory O Upgrade Airflow meters Controls upgrade Airflow rreters O Boost limiter cut feature Eliminates factory boost limiter 0 Anti Engine Stall feature This is used to stabilize the rough idle due to turbo compressor surge Blow off valve vented out to the atmosphere or use of a high lift carnshaft O VTECR Setting This is used to set the VTEC setting without going in to the Main Unit O Map Trace feature This allows the tuner to pin point the current location on any map table O Real Tirre Display feature This allows the tuner to monitor the engine condition in real tire O Real Time Communication This allows the PC and e Manage to conmnicate at real time Any changes made on the computer screen is sent to e Manage with in 2 3 sec O Data Logging feature This allows the tuner to view the data recorded and saved during the real time mode in graph form O Security Setting feature Th
5. is allows the tuner set up a password to apply a security lock to the data in the rain unit Optional Parts O Harness Kit Injector control This harness is used when controlling main injectors or sub injectors O Harness Kit Ignition Timing Control This harness is used when controlling the ignition timing O GReddy Pressure Sensor GReddy pressure sensor can be used for the scale of each Map table This is used when the factory system exceeds the Air Flow Meter or MAP sensor Capacity 4 Before installation of the software please make sure that the PC is set up correctly This product will only operate on Wndowsr 95 98 Me or 2000 that meets the requirements listed below System Requirements O IntelR PentiurrkR 166MHz or faster processor D At least 32MB of RAM e4MB recommrended O A hard drive with at least 50MB of free space A SVGA monitor 800x600 and al6bit high color display D A3 5inch 1 44MB floppy disk drive O A CD ROM drive D Serial port with RS 232C D Sub 9 pin connector male Important O If the Serial port is not D Sub 9 pin connecter mele an adapter will be necessary to connect the communication cable O For computers that are not equipped with a Serial port a USB to Serial adapter is required Do not use USB to USB cable If your computer meets the requirement listed above the basic features of this program will operate but to use the Real Time Monitor feature requires the followi
6. itches 3 setting inforrmation please refer to the e Manage manual Important D For the Ignition Input J unper Setting refer to the Wre O The updated program will confirm once the unit is turned OFF diagram for Ignition Harness on page When the unit is turned back ON the following message will come Air Flow Meter 1 Used for Hot wire flap type airflow meters or MAP sensors O Air Flow Meter 2 Used for GTR Skyline or VTEC O Airflow Meter Pulse Input Used for Karman type airflow meters or VTEC O Airflow Meter Pulse Output Used for Karman type airflow meters or VTEC 0 AAV Value Displays the Main Unit s AAV settings up The data in the Main Unit weas lost Please export data this shows that the unit was properly updated 5 This completes the update of the communication program If the 12 pin connector was disconnected please reconnect it back 13 12 Parameter Setting This window allows you to change Airflow Meters Injectors set the Throttle aThrottle and select which map to use To read the programin the Main Unit select the Inport Data in the Comrrunication menu bar or click on the Inport Data icon oy en LT z Pai To show the Paran ter Setting select the Pararreter Setting in the Settings menu bar or click on the Parameter Setting icon PARAMETER SETTING Pararreter Setting Air Flow Meter Change O When
7. ng Required to use the Real Time Monitor O IntelR Pentium Il R 266MHz or faster processor O At least 128MB of random access memory RAM As for the setup and installation of the Windowsr please refer to the Getting Started manual included in the Windowsr Software Basic PC Operation This system will basically operate the sarre as any other Windowsr based software such as changing window size closing window mouse operation quitting and etc For further information please refer to the Getting Started manual included with the Windowsr Software Please Note O The Support Tool v1 10 software has a Main Unit e Manage Update v1 20 program that will autorratically detect and update an old version unit when the Main Unit is linked Wth the PC PROJECTGSC PROJECTASC Follow the instructions listed below to install the Support Tool software Software Installation 1 Turn Personal Computer ON 2 Insert the Support Tool CD ROM in the CD ROM drive This softwere is a Self installing software so installation will begin soon as the CD ROM is inserted Follow the instruction on the screen 3 After the installation is complete GReddy e Manage short cut icon will appear on the desktop Important 0 If the self installation fails Depending on the computer s settings it will not allow self installation When this happens double click the setup exe in the DISK1 folder in the CD ROM to install the soft
8. oid open sparks flames or operation of electrical device near flammable substances O Make sure there are no leaks in the fuel system and that all of the connections are secure O Improper tuning of the e Manage can cause damage to the engine O GReddy Performance Products Inc will not take an responsibility of darnage caused by improper installation or tuning O Tuning should be performed only by a technician who full understand the vehicle s fuel management and ignition timing requirement for the engine being tuned Always s use a proper air fuel ratio meter when tuning the e Manage D Installation of this product requires modification of the vehicle s electrical system O When meking wire connections be sure to renove the key fromthe ignition and disconnect the negative terminal of the battery DO Never short out the system It can damage the unit as well as the vehicle s electrical system O Read and fully understand the wiring diagram before making any wire connection O When connecting the connector push it in all the way until you hear them click in together O The conrrunication cable is not a repairable item so please take care of it When disconnecting fromthe PC laptop pull holding the connector Never pull on the cord Please O The product and the instruction manual are subject to change without notice O Check the parts list and make sure you have received all the items in the list CD
9. the Airflow meter or MAP sensor is upgraded check the Sensor Type fromthe Vehicle Specific ECU wire location chart and select it fromthe pull down menu O The Airflow Type programmed with the Main unit s rotary switch will display as Main Unit Setting in the pull down menu When the airflow meter is upgraded the airflow signal value will change Make sure to check Air Fuel Ratio with a proper equipment to ensure proper fuel mixture GReddy Pressure Sensor O Choose this box when an optional GReddy pressure sensor will be used for the scale of each Map tables O This function is used when the system exceeds the Air Flow Meter s capacity The factory ECU will continue to read off the Air Flow Meter but the e Manage system will work off the GReddy pressure sensor O In the Sub Injector Map the injectors can be controlled by rom and the GReddy pressure sensor signal Absolute Pressure Sensor Change O This function is used when the system exceeds the factory MAP Sensor capacity The factory ECU will continue to read off the factory MAP sensor but the e Manage system will use the calculated absolute pressure fromthe factory and GReddy pressure sensor Use Absolute Pressure Sensor when setting the vacuum as O value Use Relative Pressure Sensor when setting atmospheric pressure as O value 15
10. ware O If the program does not operate properly Uninstall the program and reinstall the program O If communication feature does not operate Uninstall the program and reinstall the program To uninstall 1 Click on the ADD REMOVE PROGRAM in the CONTROL PANEL 2 From ADD REMOVE PROGRAM list select GReddy e Manage Support Tool then click on ADD REMOVE button 3 Click OK 4 When it return to the ADD REMOVE PROGRAM window dick OK to go back to CONTROL PANEL 5 Close the CONTROL PANEL window es i jac ra eR ma Wre diagram for Injector Signal Please read the instructions included with the Injector Harness kit and proceed with the wiring only if you fully understand the instructions O Connect to the vehicle s Injector signal wires Refer to the Vehicle Specific ECU wire location chart at the end of this manual for the proper location of each wire Make sure that you connect sarre nurrber of wires as the engine s cylinder number Excludes Rotary engines O For Rotary engines you can only wire the primary or secondary injector signal or both Example 1 For BNR32 ECU Example 2 For JZX90 ecu R Male connector 6 cylinoer engine with i 0 Female connector Enane Coatrat Und 3 injector signat wire Engine Comrat Unk t Splice FRA Gs J CH 4 YA G JO 3 OR U4 5CH2 BURA QUZ 3 OH Exampte 4 For NAGCE R Male connector 6 cytinder engine wiin G Female connector Engne Controt
11. you see the following Take it easy GReddy e manage Support Too Stage 1 TREI oo RO TASS CO LTD Apra eriari Made ir Jape O Use only the provided communication cable If a different cable is used it might damage the PC or and the e Manage Download the comtrunication Program Main Unit Update 1 Always disconnect the 12 pin connector on the main unit 2 Check and make sure that the status bar is displaying ONLINE If it does not show ONLINE Check the COM port setting 11 a al z BE pose 3 The program will autorratically detect a unit will old system program When the update window shows up on the screen click OK to i Main Unit Setting Information Confirmation start downloading the update Download will take about 2 min 1 Turn the IG key to ON position and check to make sure that the status bar is displaying ONLINE If it does not show ONLINE Check the COM port setting 2 To confirmthe Main Unit Setting Information select the Main Unit Setting Information in the Setting or click on the Main Unit Setting Inforrration icon Changes can not be made in this window MAIN UNIT SETTING INFORMATION EF Please O Do not disconnect the communication cable during the comtrunication PC and the e Manage will not function properly 4 When the updating is complete the following window will pop up Tum the IG key to OFF position and click OK O For the Rotary sw
Download Pdf Manuals
Related Search