EQ Series User Guide Installation Instructions
Contents
1. and insert 4 AA batteries according to gray black to black Note that the upper compartment of the control SSPS to the blue connector on the to the diagram inside the housing the connectors are keyed for proper box Attach the wiring connectors turbine and tuck them into the cavity NOTE Make sure the batteries are installation as shown in the detail below first gray to gray then black to black as shown oriented properly before testing the Snap the completed connections into Note that the connectors are keyed faucet the wiring harness as shown for proper installation as shown in the detail below Snap the completed connections into the wiring harness as shown AC Power QUICK TROUBLESHOOTING Follow the steps below to fix common problems For detailed troubleshooting visit eqfaucets com Before troubleshooting remove any objects in detection zone and make sure sensor is clear of debris Ensure power is applied and solid red light appears during first 5 seconds after power up The faucet is leaking 120VAC 60 Hz From outlet tighten or replace outlet insert using included key i Choose a location and mount the ii Attach the wiring connectors gray iii Plug the transformer into iv Wire up the From supply stops install or replace transformer Run the cable from the to gray black to black Note the wall transformer to the filter screen gaskets see diagram on transformer through the opening in that t2. EQ Series User Guide Installation Instructions For single supply and dual supply EQ Series faucets Overview Chicago Faucets EQ Series faucets feature three designs in two finishes with heavy duty cast brass spouts and high quality electronic components The faucet is up and running in minutes without the need for programming Superior user detection means EQ turns on when user approaches and shuts off when user leaves It also adjusts for optimal performance saving water Safety Information Read this entire user guide to ensure proper installation Compliance and conformity to local codes and ordinances is the responsibility of the installer The following safety notes must always be complied with during handling of this product e Make sure there is enough space and lighting available during installation and service e Do not modify or convert this Chicago Faucets product yourself All warranties will be voided Notice to the Installer e Read this entire instruction sheet before installing to ensure proper installation e Installation must comply with local codes and ordinances e Do not use pipe dope e Care shall be exercised when installing the device to prevent marring the exposed decorative surfaces The supply piping to these devices shall be securely anchored to the building structure to prevent installed device from unnecessary movement when operated by the user NOTE The information in this manual is subject to change with
3. ents including the solenoid are warranted for three 3 years from the date of installation FIVE YEAR CARTRIDGE WARRANTY The Cartridge defined as the metal portion of any Product typically referred to by the product numbers containing 1 099 1 100 377X The Chicago Faucet Company 217X and 274X excluding any rubber or plastic components is warranted against material manufacturing defects for a period of five 5 years from the date of Product purchase 2100 South Clearwater Drive All Cartridges included in the Company s Single Control or Shower Products also are warranted against material manufacturing defects for a period of five 5 years from the date of Product purchase Des Plaines IL 60018 ONE YEAR FINISH WARRANTY COMMERCIAL For Products used in commercial applications the finish of the Product is warranted against material manufacturing defects for a period Phone 847 803 5000 of one 1 year from the date of Product purchase Fax 847 803 5454 OTHER WARRANTIES All other Products not covered above are warranted against material manufacturing defects for a period of one 1 year from the date of Product purchase Technical 800 832 8783 Other restrictions and limitations apply For complete warranty details call Chicago Faucets Customer Service at 847 803 5000 or visit chicagofaucets com www chicagofaucets com 2014 Chicago Faucet Company 957 109 00 0 12 14
4. he connectors are keyed for main line page 1 the control box proper installation as shown in the detail below Snap the completed connections into the wiring harness as shown Make sure supply hoses are connected and supply stops are fully open Clean or replace filter screen gaskets or outlet insert No water flow or flow is limited Completing Installation Testing and Adjustment Water flow does not stop If water flows continuously but stops when hand enters detection zone reverse solenoid electrical connections Faucet does not properly detect user Remove and reapply power or run faucet to maximum run time This will cause automatic recalibration of sensing field Recalibration is complete when solid red light disappears If the steps above do not solve the problem you may need to replace 1 Once wiring is complete the 2 Adjusting the Water Temperature 3 Reinstall the control box cover the spout assembly or control box red sensor light at the faucet a The yellow mixer handle inside b The mixed water temperature and secure it with the 2 For eG ele Lelie contaci outlet will glow continuously the control box is used to must be checked at the point of Phillips screw inlet ale Ue aS esr ese se Or o ee Aer ae Ngn adjust water temperature use and the CFC mixing valve aii COVA switches off place your hands in dual supply installations adjusted to ensure delivery of in front of the faucet The faucet Tu
5. lat washers and wing nuts to the threaded rods before reinstalling the metal key and securing it with the yellow locking tab 3 Open the supply stops and check for leaks Note water may run through spout 4 When the spout is in the desired position use a wrench to tighten all mounting hardware 17 21 43 53 a 4 Determine the position of the control box under the sink Hold the control box against the wall and mark the locations of the two mounting holes Orientation is not critical EQ High Arc 5 Drill 3 16 holes install wall anchors and mounting screws Be sure to leave at least 1 2 12mm of the screw head exposed Secure the control box to the wall using a 2 Phillips screwdriver Connecting Power and Solenoid 1 Bring wire into box Use length of box for measurement Snap into holder on side For additional technical assistance call 800 TEC TRUE 800 832 8783 or visit our website at chicagofaucets com 2 Attach power connections as shown in the following sections EQ Series User Guide Installation Instructions CHICAGO Ay continued FAUCETS a Geberit company Battery DC Power Self Sustaining Power System SSPS O 5 5 y p lt Q O O f ev lt y Cc o 5 ro ii Attach the wiring connectors gray i Insert the SSPS power supply into ii Connect the blue connector on the
6. out notice Operating static pressure 20 125 PSI 188 862 kPa Minimum static pressure for mixing 30 PSI 207 kPa COLD water inlet temperature range 40 80 F 4 27 C HOT water inlet temperature range 100 180 F 38 82 C Maximum hot water range outlet from thermostatic mixing valve 80 120 F 27 49 C Installation may be performed at different times of construction by different individuals For this reason these instructions should be left on site with the facility or maintenance manager NOTE Before installation turn off water supplies to existing faucet and remove faucet if replacing Clean faucet basin and clear away debris Flush all supply lines before connecting to faucet Failure to do so can result in debris clogging the inlets and or internal control and mixing valves Maximum hot water range outlet from mechanical mixing valve 40 140 F 4 60 C Maximum pressure differential between Hot amp Cold water supplies 20 Maximum inlet water supply temperature differential 20 F 9 C In order to complete the installation you will need the following tools and supplies e Phillips Screwdriver 1 2 3 e Drill with 3 16 Bit e Adjustable Wrench e Mallet e Tape Measure e Plumbers Putty e Silicone based Lubricant e 1 2 Deep Socket or 3 Flat Head Screwdriver CHICAGO Ay FAUCETS a Geberit company EQ Angular i EQ Curved i N Mounting of Faucet and Optional Co
7. rn the handle clockwise to water at a safe temperature no should activate and water decrease water temperature or exceeding 110 F 43 C Water should flow from the spout counter clockwise to increase temperatures in excess 110 F water temperature 43 C are dangerous and may cause scalding severe injury or death WARNING Delivery of water to fixtures intended for hand washing is recommended to be controlled by valves listed to ASSE 1070 This fitting is NOT factory preset and can be adjusted to deliver water at temperatures exceeding 110 F 43 C Further mechanical mixing valves DO NOT provide automatic control of water temperature Due to effects of various water conditions periodic verification of outlet water temperature is required Care and Maintenance Periodic inspection and yearly maintenance by a licensed contractor is required for all thermostatic mixing elements Corrosive water conditions and or unauthorized adjustments or repair could render the thermostatic valve ineffective for service intended Regular checking and cleaning of the valve s internal components and check stops helps assure maximum life and proper product function Frequency of cleaning and inspection depends on local water conditions All Chicago Faucets fittings are designed and engineered to meet or exceed industry performance standards Care should be taken when cleaning this product Do not use abrasive cleaners chemicals or solvents as they can result in s
8. urface damage Use mild soap with warm water for cleaning and protecting the surface of Chicago Faucets fittings For additional technical assistance call 800 TEC TRUE 800 832 8783 or visit our website at chicagofaucets com CHICAGO FAUCETS LIMITED WARRANTY TO WHOM DOES THIS WARRANTY APPLY The Company extends the following limited warranty to the original user only WHAT DOES THIS WARRANTY COVER AND HOW LONG DOES IT LAST This warranty covers the following Commercial Products LIFETIME FAUCET WARRANTY The Faucet defined as any metal cast forged stamped or formed portion of the Product not including electronic or moving parts or other products separately covered by this Limited Warranty or water restricting components or other components is warranted against material manufacturing defects for the life of the Product FIVE YEAR FAUCET WARRANTY Certain Products and portions of the Product are warranted against material manufacturing defects for a period of five 5 years from the date of Product purchase Products warranted against material manufacturing defects for a period of five 5 years from the date of Product purchase are referred to by the product numbers 42X 43X 15XX and E Tronic 4X 5X 6X 7X 8X and 9X All zinc die cast portions of Product are warranted against material manufacturing defects for a period of five 5 years from the date of Product purchase THREE YEAR ELECTRONICS WARRANTY Electronic compon
9. ver Plate 1 Install the gasket on the bottom of the spout flat side down If installing a cover plate align the holes in the spout base with the pins on the plate and feed the power cable and braided hose through the plate Secure the plate to the spout with the 3 Phillips screw Mounting Control Box 1 Remove the control box cover by using a 2 Phillips screwdriver to loosen the cover screw 2 Attach the threaded rods to the bottom of the cover plate Apply plumber s putty to the underside of the cover plate where shown 2 Pivot the yellow locking tab and remove the metal key at the top of the control box Apply silicone based lubricant to the end of the spout hose and insert it through the hole Connecting Water Supply dual supply unit shown 1 Insert the filter screen gaskets into the supply stops IMPORTANT the filter screen gaskets seal the connection against leaks and must be installed as shown 2 Attach the 3 8 female com pression supply hoses from the control box to the supply stops Use a wrench to tighten the nuts to the supply stops IMPORTANT Remove any debris or hardware from the sink before opening the supplies and testing the faucet 3 Position the faucet on the sink For all installations hand tighten the spout to the deck with the large black spacer and long mounting nut For installations with a cover plate also attach the large cup washers f
Download Pdf Manuals
Related Search