Home
View - Industry Gear
Contents
1. WWW LIGHTEMOTION COM AU P645QUADO User s instruction manual This manual contains important information about the safe installation and use of this product Please read this instruction manual carefully before installing or operating Please keep these instructions in a safe place for future reference www lightemotion com au Congratulations on the purchase of your P645QAUDO by Light Emotion We are confident that you will be satisfied with your purchase We have prepared this manual to assist you with the care and operation of this item This product uses 15 4in1 5W LEDs to produce vivid colours that the user can control in many ways The unit incorporates new lens technology which produces a narrower more concentrated beam allowing fewer LEDs to be used to give a brighter effect The unit features thermal cut out so it will shut down if its interior temperature reaches 85 degrees C this will prevent damage to the product in the event of a problem Please note that as part of out ongoing commitment to continuous improvement and product development the specifications in this manual are subject to change without notice Whilst every care has been taken in the preparation of this manual we reserve the right to change specifications in the course of product improvement CONTENTS SECTION Page WHAT IS INCLUDED SAFETY INSTRUCIONTS 2 INSTALLATION 3 MAINTENANCE POWER DMX LEAD DMX TERMINATOR OPERATION 4 SPECIFICATIONS
2. 7 Please note that as part of out ongoing commitment to continuous improvement and product development the specifications in this manual are subject to change without notice Whilst every care has been taken in the preparation of this manual we reserve the right to change specifications in the course of product improvement WHAT IS INCLUDED CAUTION Do not use sharp objects whilst unpacking this product e 1x P645QUADO 1 x Warranty card 1 x User manual 1 x 5 Meter power cable with normal Australian plug 1 x 1 Meter DMX adaptor cable with female IP plug and male XLR plug 1 x Female DMX end cap 1 x Male DMX end cap 1 x Female power end cap e Do not include IR remote controller P645QUADOR Please note Some of the items above may be fitted to the product by the manufacturer SAFETY INSTRUCTIONS Please read these instructions carefully It includes important information about the installation usage and maintenance of this product e Please keep this User Manual for future consultation If you sell the unit to another user be sure that they also receive this instruction booklet e Always make sure that you are connecting to the proper voltage and that the line voltage you are connecting to is not higher than that stated on the rear panel of the fixture e This is an IP65 rated outdoor fixture To prevent damage to the waterproof seal do not pull the product apart yourself Refer to qualified person e Make sure there are no flamm
3. able materials close to the unit while operating e The unit must be installed in a location with adequate ventilation at least 50cm from adjacent surface Be sure that no ventilation slots are blocked e Always disconnect from power source before servicing or replacing fuse and be sure to replace with same fuse source e Secure fixture to fastening device using a safety chain Never carry the fixture solely by its head Use its carrying handles e In the event of serious operating problem stop using the unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Always use the same type spare parts e Never connect the device to a dimmer pack e Make sure power cord is never crimped or damaged e Never disconnect power cord by pulling or tugging on the cord e Avoid direct eye exposure to the light source while it is on INSTALLATION CAUTION For safe mounting read the following instructions carefully e Use suitable hook clamps for hanging the lighting effect e Use a safety wire with a breaking strain of more than sate double the lighting effect e Do not look directly into the light source e Make sure the lighting effect has suitable ventilation as per the instructions below e This lighting effect is intended for indoor use only to avoid electrical shock keep away from rai
4. door LED bar 4IN1 fixture you must aim the controller at the front of the fixture and no more than 10 meter away NOTE IR remote is ready to control the light which is in any working mode Recover to manufactory setting Press SET ADDR and press 9510 unit will back to manufactory setting run at auto run mode Black Out mode Press BLACK OUT to turn the LED lights on off Select program Mode Use PROG button to select auto run mode built in programs mode LEDs will indicate you current mode When red LEDs are on after you press PROG unit is in built in programs mode When green LEDs are on after you press PROG unit is in auto run mode 1 Select built in programs Press PROG to select built in program mode red LEDs should light on then use or to select 12 built in programs You can also press FLASH to set the program fade to adjust it Press SPEED to set the program running to adjust it speed and then press or speed and then press or NOTE Pr 01 is static color program There are 15 colors to choose Press the SPEED button to enter the static color submenu and then pressing and buttons to scroll through the static colors static color Fifteen color slow dream Program 01 Program 02 Program 03 Program 04 Program 05 Program 06 Program 07 Program 08 Program 09 Program 10 Program 11 Program 12 Fifteen color fade cha
5. n and gt moisture D e Keep unit out of reach from children NOTE Use washers and spring washers when attaching your hook clamp to the yoke 1 For installation of the hook clamps and safety wire This lighting effect must be 0 5m away from any flammable materials or any walls or ceilings 3 Do not block or inhibit the air flow from the ventilation vents MAINTENANCE amp PERIODIC CHECKS CAUTION Some maintenance and checks may require the product to be opened and should only be done by qualified persons Warranty may be void if damage has been caused by improper maintenance Perspex lenses should be wiped with a clean moist cloth to remove dust and residue POWER CAUTION This lighting effect is designed to operate at 110 240V 50Hz 60Hz Connect the supplied power lead to the lighting effect Power input socket Power Consumption 95W DMX LEAD The DMX lead is used to link up multiple units DMX IN DMX OUT DMX512 1 2 2 1 PIN FUNCTION 1 GND 2 DATA 3 3 3 DATA DMX TERMINATOR CONNECTION Connect a 120 OHM resistor across pins 2 and 3 in an XLR plug and insert into the DMX OUT socket on the last unit in the chain DMX TERMINATOR A DMX terminator helps to reduce noise on the DMX chain and makes the light respond to control more accurately It should be plugged in to the last fixture in any chain OPERATION The IR remote can control the out
6. nge Fifteen color jumping Fifteen color signal direction flow Fifteen color double direction flow Fifteen color signal direction flow dream 1 Fifteen color signal direction flow dream 2 Signal direction section flow 1 Signal direction section flow 2 Double direction section flow Fifteen color mixing Select auto run mode Press PROG to select color change mode green LEDs should light on then use and 66 66 to select color changing speed Color dreaming mode Press PROG to select color dreaming mode blue LEDs should light on then use or 6 99 to select the color dreaming speed Master and slave mode Press SLAVE SA button to set the LED light to slave mode Manual colour mode Press R G B W to choose the four different colors then press and to adjust brightness of RGBW individually DMX MODE You must set the DMX Channel mode before you set your DMX address 1 Set DMX mode Press the DMX mode button then RGBW LEDs will flash 2 3 times then press the or ee 99 buttons to select different DMX address You also can press SET ADDR to set up DMX address 2 Set DMX address Press SET ADDR then use number button to set DMX address You must use three digits for your DMX address For example you want to set DMX address to 012 Press SET ADDR then RGBW LEDs will flash 2 3 times Then the red LEDs will stay on and wait your first digit P
7. ress the first digit 0 then the green LEDs will stay on and wait your second digit Press the second digit 1 then the blue LEDs will stay on and wait your third digit Press the third digit 2 then RGBW LEDs will flash 2 3 times to confirm your setting Unit will automatic in DMX mode When you enter wrong DMX address red LEDs will on You have to re set again DMX chart CH7 CH6 CH5 CH4 CH3 CH2 CH1 MODE DMX VALUE FUNCTION White Blue Green Red 0 255 0 255 0 255 0 255 va No puncon dims l am Time me bright bright bright bright 2 4 17 Red 3 18 31 Green 4 32 45 Blue 5 46 59 White 6 60 73 R G Dimming Strob z 7 14 87 nee 11 255 ae No 8 88 101 R W slow gt qu bright function 9 102 115 G B ick 10 116 129 G W None 11 130 143 B W No No 12 144 157 R4 G B function function 13 158 171 R G W 14 172 185 R B W 15 186 199 G B W 16 200 213 R G B W 17 214 227 Color change Speed 18 228 241 Color dreaming ve i slow quic 19 242 255 Auto run k Note R red G green B blue W white SPECIFICATION Weight 6 2kg Size 28 5 X21 X31 5cm Power input AC100V 240V SOHZ 60HZ Wattage 95W LEDS 15PCS 5W 4 in one Beam angle of LEDs 40 degree 3PIN female and male XLR socket 4PIN female and male power socket 4 button LED digital display IR remote available IP rate IP 65
Download Pdf Manuals
Related Search
Related Contents
日本HP お客様事例:栗山米菓様 - Hewlett Philips Sleek micro music system DCB293 Catalogo seconda parte Gizmo user manual Print Preview - C:\Temp\.aptcache\aeq5og2c/tfq5ooas Uniross Universal Battery Charger User Guide Sitecom Network Internet Security Camera Dizzy User Manual - MAGNET Project Sony RHCU2 User's Manual Copyright © All rights reserved.
Failed to retrieve file