Manual - longshine networking
Contents
1. FCC Certifications FC This Equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CE Mark Warning C This equipment complies with the requirements relating to electromagnetic compatibility EN 55022 class A for ITE the essential protection requirement of Council Directive 2004 108 EC on the approximation of the laws of the Member States relating to electromagnetic compatibility Company has an on going policy of upgrading its products and it may be possible that information in this document is not up to date Please check with your local distributors for the lates2. IEEE802 3 10BASE T IEEE802 3u 100BASE TX IEEE802 3ab 1000BASE T IEEE 802 3z 1000Base X IEEE802 3x full duplex flow control 24 10 100 1000Mbps Ru 45 ports 2 Mini GBIC ports RJ 45 10BASE T Category 3 4 5 UTP STP RJ 45 100BASE TX Category 5 UTP STP RJ 45 1000BASE T Category 5 5e or enhanced UTP STP Fiber depend on Mini GBIC types 10 100 1000 Mbps Auto negotiation 10 100Mbps Full duplex Half duplex 1000Mbps Full duplex System Power Ports Link ACT 16K MAC entries 448K bytes buffer memory 9K bytes Operating 0 40 C 32 104 F Storage 40 70 C 40 158 F Operating 10 90 non condensing Storage 5 90 non condensing Power Supply Internal power supply Emission FCC CE VCCI Class A
3. 1 Attach the provided rubber feet to the bottom of the switch to keep the switch from slipping The recommend position has been square marked 2 Install the switch on a level surface that can support the weight of the unit and the relevant components 3 Plug the switch with the female end of the provided power cord and plug the male end to the power outlet 61NB G626D0 200 Rack mount Installation The switch may standalone or may be mounted in a standard 19 rack Rack mounting produces an orderly installation when you have a number of related network devices The switch is supplied with two optional rack mounting brackets and screws which are used for rack mounting the unit Procedures to Rack Mount the switch in the rack 1 2 First disconnect all the cables from the switch Place the unit the right way up on a hard flat surface with the front facing you Locate a mounting bracket over the mounting holes on one side of the unit Insert the screws and fully tighten with a suitable screwdriver Repeat the two previous steps for the other side of the unit Insert the unit into the rack with suitable screws Reconnect all the cables Network Cables 1 Crossover or straight through cable All the ports on the switch support Auto MDI MDI X functionality Both straight through or crossover cables can be used to connect the switch with PCs as well as other devices like switches hubs
4. Act LEDs LED Status Operation Power Steady Green _ The switch is powered on Off The switch is powered off Steady Green _ Valid port connection Valid port connection and Link ACT Blinking Green there is data transmitting receiving Off Port disconnected Ports Operation The auto negotiation feature allows ports running at one of the following operation modes Speed Duplex fuk aii Mbps Mode 10 Haf 10 100 1000Mbps Hal 10 100 1000 copper 100 S Mops 1000 Full 1000Mbps Fiber 1000 Full Mini GBIC required Rear Panel The back side is shown as bellow contains a three pronged outlet Power Receptacle To be compatible with the electric service standards around the world the switch is designed to afford the power supply in the range from 100 to 240VAC 50 60Hz Please make sure that your outlet standard to be within this range To power on the switch plug the female end of the power cord firmly into the receptacle of the switch and the other end into an electric service outlet After the power cord installation please check if the power LED is illuminated for a normal power status Installation This switch can be placed on your desktop directly or mounted in a rack The installation is a snap Users can display all the features of the switch by simply attaching the cables and turning the power on Desktop Installation
5. or routers 2 Category 3 4 5 or 5e UTP STP cable To make a valid connection and obtain the optimal performance appropriate cables corresponding to different transmitting receiving speed is required To choose a suitable cable please refer to the following table P Speed ane Media Mbps Wiring 10 Category3 4 5 UTP STP 10 100 1000Mbps copper 100 Category 5 UTP STP 1000 Category5 5e UTP STP The cable type differs from 1000Mbps Fiber the mini GBIC you purchase Mini GBIC 1000 Please refer to the instruction required that came with your mini GBIC Tips On the purpose of performing this switch well we strongly recommend below installation environment 1 The switch is placed with appropriate ventilation environment A minimum 25mm space around the unit is recommended 2 The switch and the relevant components are away from sources of electrical noise such as radios transmitters and broadband amplifiers 3 The switch is away from environments beyond recommend moisture Network Application The following picture is an application sample of network topology for your reference QD igavit switch ss i ie Switch 1000Mbps Switch sae PC PC Storage PC Product Specifications Standard Interface Cable Connections Network Data Rate Transmission Mode LED Indications Memory Jumbo Frame Temperature Humidity
6. re flow control mechanisms work respectively for full and half duplex modes The switch is plug and play without any software to configure and also fully compliant with all kinds of network protocols Moreover the rich diagnostic LEDs on the front panel demonstrate the operating status of individual port and the whole system Key Features Complies with 10 BASE T specifications of the IEEE802 3 standard Complies with 100BASE TX specifications of the IEEE802 3u standard Complies with 1000BASE T specifications of the IEEE802 3ab standard Complies with 1000BASE X specifications of the IEEE802 3z standard Provides 2 SFP ports for optional fiber connection Supports back pressure half duplex and flow control IEEE 802 3x Supports NWay protocol for speed 10 100 1000Mbps and duplex mode Half Full auto detection Supports MDI MDI X auto crossover and polarity correction Store and forward architecture filters fragment amp CRC error packets Supports 16K MAC address Supports 448K bytes buffer memory Supports 9K bytes jumbo frame Supports IEEE 802 3az Energy Efficient Ethernet Supports extensive LED indicators for network diagnostics Front Panel The front panel consists of LED indicators and the ports 24 ports 2 Mini GBIC Ports 19 inch Model LEDs Definition This switch contains LEDs to shows the activities and information of the ports including power LED and Link
7. t information No part of this document can be copied or reproduced in any form without written consent from the company Trademarks All trade names and trademarks are the properties of their respective companies Copyright 2010 All Rights Reserved Unpacking Information Thank you for purchasing this product Before installation please verify that your package contains the following items One 24 port gigabit switch with 2 SFP ports One AC power cord Rubber foot 4 and screws Rack mount 2 One user manual OP ONS ntroduction The device is a powerful high performance Gigabit Ethernet switch with 24 10 100 1000 Mbps ports and 2 SFP mini GBIC ports providing you a cost effective space saving solution for expanding your network The gigabit ports can lead you to a real gigabit connection making you be able to transfer larger and high bandwidth needed files faster in an easy way Another feature is for your network expansion the two mini gigabit ports allow you to add fiber optic connectivity for connecting to other network switches for obtaining long distance communication Automatic MDI MDI X crossover detection ensures you no need to worry about the cable type by automatically switch the port s receive and transmit connections with plugged in devices and alleviates the effort to use crossover cables Flow control ensures the correctness of data transmitting The 802 3x and backpressu
Download Pdf Manuals
Related Search