Explorer 575 Spot MK11 - Enlightenment Entertainment Technology
Contents
1. Do not switch the device on and off in short intervals as this would reduce the 5 life Do touch the device s housing bare handed during its operation housing becomes very hot Allow the fixture to cool for at least 5 minutes before handling Do not shake the device Avoid brute force when installing or operating the device e Only use device indoor avoid contact with water or other liquids e Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened Only operate the device after having familiarized with its functions Avoid flames and do not put close to flammable liquids or gases Always replace the lamp when it is damaged or deformed due to the heat Always keep case closed while operating Always allow free air soace of at least 50 cm around the unit for ventilation Always disconnect power from the mains when device is not used before cleaning or when replacing lamp Only handle the power cord by the plug Never pull out the plug by tugging the power cord ensure the longest and most efficient use of the lamp always 15 minutes before applying power after shutdown Failure to do so could result in premature aging of the lamp and failure to the electronics that drive if e Make sure that the device is not exposed to extreme heat moisture or dust e Make sure that the available voltage is not higher than stated on the rear2. Explorer 575 Spot ORDERCODE 40191 Congratulations You have bought a great innovative product trom Showtec The Showtec Explorer 575 MKII brings excitement to any venue Whether you want simple plug amp play action or a sophisticated DMX show this product provides the effect you need You can rely on Showtec for more excellent lighting products We design and manufacture professional light equipment for the entertainment industry New products are being launched regularly We work hard to keep you our customer satisfied For more information want showtec into You can get some of the best quality best priced products on the market from Showtec So next time turn to Showtec for more great lighting equipment Always get the best with Showtec Thank you Showtec Showtec Explorer 5757 Product Guide Warning Safety instructions ii _ ________ ___ 8__ Me Description Features and CR Installation ee Installing the Lamp Lamp Adjustment SePUD and E TO E PTI VS Ses ___ ______ OM FOTO sto ee ___ __6_4_
3. Try your DMX control again 2 Determine whether the controller or light effect is at fault Does the controller operate properly with other DMX products If not take the controller in for repair If so take the DMX cable and the light effect to a qualified technician See next page for more problem solving 29 Probable cause s No power fo the fixture Check that power is switched on One or more and cables are plugged in Primary fuse blown Replace fuse completely dead Fixtures reset The controller is not connected Connect controller 3 pin XLR Out of the controller Install a phase reversing cable does not match XLR Out of the first between the controller and the first fixture on the link i e signal is fixture on the link reversed correctly but all respond erratically or not at all to the controller Check data quality If much lower than 100 percent the problem may be a bad data link connection poor Poor data quality quality or broken cables missing termination plug or a defective fixture disturbing the link Inspect connections and cables Bad data link connection Correct poor connections Repair or replace damaged cables i Data link not terminated with 120 Insert termination plug in output jack Fixtures reset a Ohm termination plug of the last fixture on the link dd t addressing of the fixt Check add tt some respond ncorrect addressing of the fixtures eck address sett
4. In this way you can stop the color wheel in any position also between two colors creating double colored beams Between 200 255 the color wheel rotates continuously the so called Rainbow effect 2033 ROD Channel 8 Static Color wheel 2 Channel 9 Prism rotating control Channel 10 Static Gobo wheel 1 Gobo Shake 150 159 Gobo Shake 7 Channel 11 Rotating Gobo wheel 2 Gobo Shake 237 255 Channel 12 Rotation Gobo 0 60 Goboddexng 61 158 Forwards gobo rotation from slow to fast 159 255 Backwards gobo rotation from slow to fast Channel 13 iris 0 255 Continuous adjustment from big to small Channel 14 Zoom Zoom 22 with focus correction Channel 15 Shutter strobe Shutter 20 250 Strobe effect from slow to fast 251 255 Channel 16 Lamp ON OFF Reset amp dimmer 30 39 Lamp on after 3 seconds Reset 40 59 60 69 Lamp off after 3 seconds 70 128 129 255 13 Control Panel When the indicator light is on means the Explorer is working C D E Fig 7 A Display D Down Button B MENU Button E Up Button C ENTER Button Control Mode The fixtures are individually addressed 001 512 on a data link and connected to the controller The fixtures respond to the DMX signal from the controller When you select the DMX address and save it the controller will display the saved DMX ada
5. panel e Make sure that the power cord Is never crimped or damaged Check the device and the power cord from time fo time e lf the lens is obviously damaged if has to be replaced So that its functions are not impaired due to cracks or deep scratches e f device is dropped or struck disconnect mains power supply immediately Have a qualified engineer inspect for safety before operating fthe device has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature f your Showtec device fails to work properly discontinue use immediately Pack the unit securely preferably in the original packing material and return it to your Showtec dealer for service e For adult use only Movinghead must be installed out of the reach of children Never leave the unit running unattended e Never attempt to bypass the thermostatic switch or fuses Forreplacement use lamps and fuses of same type and rating only e Replace the lamp if it becomes defective or worn out or before usage exceeds the maximum service life e Allow the fixture to cool down for 15 minutes before opening the fixture and replacing lamp Protect your hands and eyes with gloves and safety glasses e This device falls under protection class Therefore it is essential to connect the yellow green con
6. your product Design and product specifications are subject to change without prior notice CE Website www Highlite nl Email service highlite nl 5 HIGHLITE 25 2008 Showtec
7. 0 FOCUS d FOCUS Static Color wheel Static Color wheel 2 Prism rotating control 5 Rotating Color wheel 2 Gobo Shake Basic DMX Mode 13 Channels Horizontal movement Pan Vertical movement Tilt FOCUS Static Color wheel 1 Static Color wheel 2 Prism rotating control Static Gobo wheel Gobo Shake Rotation Gobo ___8 Rotating Color wheel 2 Gobo Shake o SSS y 9 RotaionGobo NN 000000 17 Channel settings 40191 Fan su 575 MSR 575 uL Channel 0 11 12 13 14 15 16 Scan speed Rai A e Static Gob Beam out Function Tilt Pan Fine Tilt Fine E s Colorwheel Colorwheel qus Gobos Rotation Iris Zoom Strobe Dimmer N x 5 z 2 148 184 ee e ee O 8 Maintenance The operator has to make sure that safety relating and machine technical installations are to be insoected by an expert after every four years in the course of an acceptance fest The operator has to make sure that safety relating and machine technical installations are to be inspected by a skilled person once a year The following points have to be considered during the inspection 1 All screws used for installing the device or parts of the device have to be tightly connected and must not be corroded 2 There may not be any deformations on housings fixations and installation spots 3 Mechanically moving parts lik
8. 70354 70356 70359 fastened onto the Explorer Leave at least 1 meter on all sides for air circulation 2 Always use a safety cable ordercode 70140 70141 3 Plug one end of the electric mains power cord into the IEC socket on the unit Then plug the other end of the cord into a proper electric power supply socket 4 Use the Mode button to set the fixture to RUN and choose PR6 1 The Explorer will now play its built in program Multiple Explorers 1 Fasten the moving head onto firm trussing Use a clamp ordercode 70302 70351 70354 70356 70359 fastened onto the Explorer Leave at least 1 meter on all sides for air circulation 2 Always use a safety cable ordercode 70140 70141 3 Use a 3 p XLR cable to connect the Explorers and other devices Occupation of the X LR connecti on DMX OUTPUT DMX input XLR mounting socket XLR mounting plug 1 Ground 1 Ground 2 Signal 2 Signal 3 Signal 3 Signal The transformation of the controller line of 3 pins and 5 pins plug and socket 5 Pins canon socket Pin 1 GND screen Pin 2 Signal Pin 3 Signal Pin 4 N C Pin 5 N C 3 Pins canon plug Pin 1 GND screen Pin 2 Signal Pin 3 Signal 5 Pins canon plug Pin 1 GND screen Pin 2 Signal Pin 3 Signal Pin 4 N C Pin 5 N C 3 Pins canon socket Pin 1 GND screen Pin 2 Signal
9. Addressing LED control panel DMX Channels 16 Signal input 3 pin XLR male Signal output 3 pin XLR female Oy A amp Allowed lamp models K Philips MSR 575 1000 hr 7200 ordercode 80923 Osram MSR 575 1000 hr 7200K ordercode 80923G Philips MSR 575 1000 hr 6000K ordercode 80915P Osram HSR 575 2 750 hr 6000K ordercode 809150 Electro mechanical effects 1 Rainbow Color wheel with 9 colored gobos and open 1 Static Color wheel with 7 colored gobos 3200 K 6000 K and open 1 Rotating Gobo wheel with 3 glass and 3 metal interchangeable rotating gobos plus open 1 Static Gobo wheel with 9 gobos plus open Prism 3 facer prism rotating All lenses are anti reflection coated Strobe eftect with variable speed 1 flash 10 flashes sec Pan 0 530 Tilt 0 280 Automatic Pan Tilt position correction Wheel control auto electronic reset Beam Angles 15 18 and 22 Gobos Gobo diameter metal or glass 27 mm Maximum image diameter 23 mm Glass gobo heat resistant and intensify glass dichroic glas coating Max ambient temperature ta 40 C Max housing temperature ts 80 C Cooling 2 axial fans one fan in the projector and one in the base Motor high quality stepping motor controlled by microprocessors Minimum distance Minimum distance from flammable surfaces 0 5m Minimum distance to lighted object 2m Versions for other lamps may be produced Please check the specification label on
10. Pin 3 Signal 4 Link the units as shown Fig 6 Connect a DMX signal cable from the first unit s DMX out socket to the second unit s socket Repeat this process to link the second third and fourth units 5 Supply electric power Plug electric mains power cords info each unit s IEC socket then plug the other end of the mains power cord into proper electric power supply sockets starting with the first unit Do not supply power before the whole system is set and connected properly 10 Multiple Explorers Set Up DMX Set up Note Link all cables before connecting electric power DMX Protocol Channel 1 Horizontal movement Pan Push the slider up in order to move head horizontally PAN Gradual head adjustment from one end of the slider to the other 0 255 128 center The head can be turned by 530 and stopped at any position you wish Channel 2 Vertical movement Tilt Push the slider up in order to move head vertically TILT Gradual head adjustment from one end of the slider to the other 0 255 128 center The head can be turned by 280 and stopped at any position you wish Channel 3 Pan fine 16 bit Channel 4 Tilt fine 16 bit Channel 5 Scan Speed Adjustment 0 255 Gradual adjustment Scan Speed from fast to slow Channel 6 Focus 0 255 Continuous adjustment from close to far Channel 7 Static Color wheel 1 Linear color change following the movement of the slider
11. _ __ __ gt MOU sce ses ects cat _ ____ __ _ _ _ CON DMX a ag MN Stand alone mode Menu Overview Advanced Mode 1 6 Channels er Basic Mode 13 CANNES Des sug anke aA COS EOD Maintenance ips Changing ihe Lamp Replacing the lt delen T ET STC TSO _ _ __________________ _______ Troubleshooting No Light No Movement All Products P No Response fo DMX Product Species a den de a al WARNING CAUTION Keep this device away from rain and moisture Unplug mains lead before opening the housing FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START UP SAFETY INSTRUCTIONS Every person involved with the installation operation and maintenance of this device has to be qualified follow the instructions of this manual CAUTION Be careful with your operations AN With a dangerous voltage you can suffer N a dangerous electric shock when touching the wires Before your initial start up please make sure that there is no damage caused by transportation Should there be any consult your dealer and do not use the device To
12. ductor fo earth e During the initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective e Repairs servicing and electric connection must be carried out by a qualified technician e WARRANTY Till one year after date of purchase CAUTION EYEDAMAGES Avoid looking directly into the light source meant especially for epileptics OPERATING DETERMINATIONS This device is not designed for permanent operation Consistent operation breaks will ensure that the device will serve you for a long time without defects The minimum distance between light output and the illuminated surface must be more than 2 meters The maximum ambient temperature must never be exceeded If this device is operated in any other way than the one described in this manual the product may suffer damages and the warranty becomes void Any other operation may lead to dangers like short circuit burns electric shock lamp explosion crash etc You endanger your own safety and the safety of others Rigging Please follow the European and national guidelines concerning rigging frussing and all other safety Issues Do not attempt the installation yourself Always let the installation be carried out by an authorized dealer Procedure lf the projector is lowered from the ceiling or high joists professional trussing systems have to be used e Usea clamp to mount the proj
13. e axles eyes and others may not show any traces of wearing 4 The electric power supply cables must not show any damages or material fatigue The Showtec Explorer 575 requires almost no maintenance However you should keep the unit clean Otherwise the fixture s light output will be significantly reduced Disconnect the mains power supply and then wipe the cover with a damp cloth Do not immerse in liquid Wipe lens clean with glass cleaner and a soft cloth Do not use alcohol or solvents The front PC lens will require weekly cleaning as smoke fluid tends to build up residues reducing the light output very quickly The cooling fans dichroic colour filters the gobo wheels the gobos and the internal lenses should be cleaned monthly with a soft brush To ensure proper functioning of the gobowheel we recommend lubricating the wheel every 6 months The quantity of oil must not be excessive Please clean internal components once a year with a light brush and vacuum cleaner Keep connections clean Disconnect electric power and then wipe the DMX and audio connections with a damp cloth Make sure connections are thoroughly dry before linking equipment or supplying electric power Changing the Lamp 1 Disconnect mains power supply Loosen the 3 screws X Y Z on the backside of the lamp cover See Backpanel Fig 4 2 Gently pull out the lamp board 3 Follow directions for installing a new lamp page 8 18 Replacing a Fuse Power
14. ector with the mounting bracket to the frussing system e The projector must never be fixed swinging freely in the room e The installation must always be secured with a safety attachment e g an appropriate safety net or safety cable e When rigging derigging or servicing the projector always make sure that the area below the installation place is blocked and staying in the area is forbidden The Explorer can be placed on a flat stage floor or mounted fo any kind of truss by a clamp Mounting clamp to the underside of the Explorer moving head LA OX CES Clamp Safety cable 1 2 3 Eye bolt 4 Mounting plate Improper installation can Cause serious damage fo people and property Connection with the mains Connect the device to the mains with the power plug Always pay attention that the right color cable is connected to the right place International EU Cable UK Cable US Cable Pi BROWN YELLOW COPPER FASE BLUE BLACK SILVER YELLOW GREEN GREEN GREEN EARTH Make sure that the device is always connected properly to earth Description of the device Features The Showtec Explorer 575 is a moving head with high output and great effects Rainbow Color wheel with 9 colored gobos and open 1 Static Color wheel with 7 colored gobos 3200 K 6000 K and open 1 Rotating Gobo wheel with 3 glass and 3 metal interchangeable rotating gobos plus open 1 Static Gobo wheel w
15. ely controllable functions Static Colour wheel 1 The Explorer contains a colour wheel with 10 colour positions 9 dichroic colours and one white It is also possible to rotate the colour wheel continuously at different soeeds Rainbow effect in both directions Static Colour wheel 2 The Explorer contains a colour wheel with 10 colour positions 7 dichroic colours 3200 K 6000 K and one white Static gobo wheel 1 This static gobo wheel has 9 metal gobos and open The gobos have an outside diameter of 27 mm and an image diameter of 23 mm Rotating gobo wheel 2 This rotating gobo wheel has 3 metal gobos 3 glass gobos and open The gobos have an outside diameter of 27 mm and an image diameter of 23 mm Shutter Dimmer Strobe The dimming 0 100 is provided by a simple mechanical shutter unit This unit may also be used for strobe effect 1 10 flashes per second Stand alone Mode The fixture can execute 2 pre set programs DMX Mode Automatic Mode 1 Random Mode Slave Mode Automatic Mode 2 Use the MENU button to set the fixture to Auto 1 or Auto 2 The Explorer will now play its built in program For synchronous operation of multiple fixtures the fixtures must all be connected on a data link Note Disconnect the fixtures from the DMX controller before operating otherwise data collisions can occur and the fixtures will not work properly It s necessary to insert the XLR termination plug with 120 Ohm into t
16. g the installation with screw A only the Hot Spot the brightest part of the ray of light must be centered Turn in addition screw and If the Hot Spot appears too bright you can weaken its intensity by moving the lamp closer to the reflector Turn in addition screw until the light is evenly distributed If the light at the outside edge of the ray of light appears brighter as in the center the lamp is too close to the reflector In this case move the lamp away from the reflector until the light is evenly distributed and the ray of light appears bright enough 15 Beam Angle 99 56 Foot candles 600 LUX _ E II BER ERE 0 2 5 5 7 5 10 12 5 15 17 5 20m Distance 1 3 2 63 3 95 5 27m Diameter 18 Beam Angle 193 86 48 Foot candles 520 LUX CHE 0 2 5 5 7 5 10 12 5 15 17 5 20m Distance 1 58 3 17 4 75 6 34m Diameter 22 Beam Angle 583 146 65 36 Foot candles 6270 1570 700 390 LUX px 20m Distance 7 78m Diameter Fig 5 Set Up and Operation Follow the directions below as they pertain to your preferred operation mode Before plugging the unit in always make sure that the power supply matches the product specification voltage Do not attempt to operate a 120V specification product on 230V power or vice versa One Explorer 1 Fasten the moving head onto firm trussing Use a clamp ordercode 70302 70351
17. he input of the first fixture and into the output of the last fixture in the data link in order to ensure proper transmission on the data link Addressing With this menu you can set the DMX address or address a fixture as a master slave 001 DMX addressing 1 Press MENU until the display shows then press ENTER The display will now show 001 2 And press A and to select the required address 001 512 press ENTER fo confirm 3 Press MENU the chosen address is shown on the display 15 Menu Overview Set address Reset Unreset Lamp Off Lamp On DMX Mode Automatic Mode 1 Random Mode Slave Mode Automatic Mode 2 Basic 13 Channels Advanced 16 Channels 60 seconds Light close Display ON Edition Lamp Running Time Fixture Running Time Running Time Pan Ran Reverse Tilt Tilt Reverse Color wheel Run Step Color wheel Run Linear Dimmer Dimmer Reverse Strobe Strobe Reverse Gobo Run Step Gobo Run Linear Stop Current Setting Run Current Setting Default Pan Begin DMX Value 0 255 End DMX Value for Pan Scan Tilt Begin DMX Value 0 255 End DMX Value for Tilt Scan Run Setting on XY Scan Angle Default No Run Setting on XY Scan Angle Lamp controlled by DMX Lamp not controlled by DMX DMX Control Reset No DMX Control Reset Set Userkey Set Password Advanced DMX Mode 16 Channels 5 Scan Speed Adjustment 0 000000
18. ing Bypass one fixture at a time until normal operation is regained unplug One of the fixtures is defective and both connectors and connect them disturbs data transmission on the directly together link Have the defective fixture serviced by a qualified technician Install a phase reversing cable erratically or not at all to the controller 3 pin XLR Out on the fixtures does between the fixtures or swap pin 2 not match pins 2 and 3 reversed and 3 in the fixture that behaves erratically Shutter closes The color wheel gobo wheel ora Contact a technician for servicing if suddenly gobo has lost its index position and the problem persists the fixture is resetting the effect The power supply settings do not Disconnect fixture Check settings No light match local AC voltage and and correct if necessary frequency Allow fixture to cool Lamp cuts out Fixture is too hot Clean fan intermittently Make sure air vents at control panel and front lens are not blocked up the air conditioning The power supply settings do not Disconnect fixture Check settings match local AC voltage and and correct if necessary frequency 24 280 Product Specification Model Showtec Explorer 575 MKII Voltage 240V 50Hz CE Power 850W Fuse 10A 250V Dimensions 465x450x580mm LxWxH Weight 36 5 kg Operation and Programming Signal pin OUT pin 1 earth pin 2 pin 3 Set Up and
19. ith 9 gobos plus open DMX control via standard DMX controller 16 DMX control channels required Strobe effect with adjustable speed 1 10 flashes sec Electronic focus Pan 0 530 ilt O 280 amp MSR 575 Fuse TIOA 250V Overview N Fig 1 1 Lens 2 Display 3 Menu Select buttons Backside LIGHTING CONTROL PROTOCOL DMX512 SERIAL DATA LINK OUT IN 4 5 6 7 Fig 2 4 DMX signal connector OUT 5 DMX signal connector IN 6 ON OFF 7 250V Installation Installing the Lamp The Showtec Explorer 575 uses the MSR 575 ordercode 80915P 809150 bulb as manufactured by all popular manufacturers Use only the appropriate lamp for your unit Note that product versions that use other lamps may be offered in the future Check your product specification label for information Always disconnect from electric mains power supply before changing lamps The lamp has to be replaced when if is damaged or deformed due to the heat Do not install lamps with a higher wattage Lamps with a higher wattage generate temperatures the device was not designed for Damages caused by non observance are not subject to warranty Procedure 1 Loosen the 3 screws X Y 7 on the backside of the lamp cover See Fig 4 2 Gently pull out the lamp board 3 Read lamp instructions Do not touch the lamp bulb glass See Figure 3 Oil on hands shortens
20. maintain perfect condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this manual Please consider that damages caused by manual modifications to the device are not subject to warranty This device contains no user serviceable parts Refer servicing to qualified technicians only IMPORTANT Ihe manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorized modification To the device e Never let the power cord come into contact with other cables Handle the power cord and all connections with the mains with particular caution e Never remove warning or informative labels from the unit e Never use anything to cover the ground contact Neverrun the device without lamp e Never ignite the lamp if the objective lens or any housing cover is open as discharge lamps may expose and emit a high ultraviolet radiation which may cause burns e Never lift the fixture by holding it at the projector head as the mechanics may be damaged Always hold the fixture at the transport handles e Never place any material over the lens Never look directly into the light source e Never leave any cables lying around e Never unscrew the screws of the rotating gobo as the ball bearing will otherwise be opened Do not insert objects into air vents e Donot connect this device to a dimmerpack
21. ress the next time DMX Addressing The control panel on the front side of the base allows you to assign the DMX fixture address which is the first channel from which the Explorer will respond to the controller Please note when you use the controller the unit has 16 channels When using multiple Explorers make sure you set the DMX addresses right Therefore the DMX address of the first Explorer should be 1 001 the DMX address of the second Explorer should be 1 16 17 017 the DMX address of the third Explorer should be 17 16 33 033 etc Please be sure that you don t have any overlapping channels in order fo control each Explorer correctly If two or more Explorers are addressed similarly they will work similarly For address settings please refer to the instructions under Addressing menu 001 Controlling After having addressed all Explorer fixtures you may now start operating these via your lighting controller Note After switching on the Explorer will automatically detect whether DMX 512 data is received or not The problem may be he XLR cable from the controller is not connected with the input of the Explorer The controller is switched off or defective the cable or connector is detective or the signal wires are swappedi in the input connector Note It s necessary to insert a XLR Termination plug with 120 Ohm in the last fixture in order fo ensure proper transmission on the DMX data link 14 Remot
22. surges short circuit or inappropriate electrical power supply may cause a fuse to burn out If the fuse burns out the product will not function whatsoever If this happens follow the directions below to do SO 1 Unplug the unit from electric power source 2 Insert a screwdriver into the slot in the fuse cover Turn the screwdriver to the left 3 Remove the used fuse If brown or unclear it is burned out 4 Insert the replacement fuse into the holder where the old fuse was Reinsert the fuse cover Be sure to use a fuse of the same type and specification See the product specification label for details Replacing a Gobo Gobo wheel with rotating gobo s 1 Disconnect mains power supply and set the switch to OFF 2 Make sure that the gobo you want to insert has the same size For the right size see below Image 23 mm 2 mm Diameter Fig 8 3 Remove the maintenance cap 4 Turn the gobo wheel with the gobo you want to remove to the upside 5 Very carefully take the pinchcock fig 9 and 10 out of the gobo wheel but pay attention that the pinchcock does not fall in the device Then push the gobo out 6 Place the new gobo in the gobo wheel Carefully put the pinchcock back gently press the pinchcock a little bit together Possibly use a pair of pliers to press the pinchcock a little bit together 7 Replace the maintenance cap and fasten all screws 19 Static Color wheel 1 Static Color wheel 2 Rotating Gobo
23. the lamp life If you touch the bulb glass wipe off the glass with a clean lint free towel and rubbing alcohol 4 Insert the lamp pins into the small holes in the lamp socket You can adjust the distance between the lamp and the lens screw A on the back 5 Put the lamp board back and fasten the screws snugly RSS 2 Lamp board Lamp holder 1 2 3 4 Fig 3 Remove the screws X Y and 2 for re lamping x JN amp Backside Lamp Board WARNING Disconnect the fixture from AC power before r lamping Lamp is hot Risk of fire Protect hands eyes Wait at least 15min before opening the covers and removing lamp from the fixtufe 0 aximum room temperature t 40 Minimum distance from flammabl material d 0 5m Exterior surface temperature 80 C Not for domestic use z o C Adjust lamp AVS A B and C Fig 4 3 adjustment screws A B C Lamp Adjustment You can adjust the lamp s position by turning the screws A B The lamp position is set in the factory As the lamps which can be used differ from manufacturer to manufacturer it can be necessary to readjust the position The lamp must be readjusted e g if the light does not seem to be evenly distributed within the ray of light Ignite the lamp and focus the ray of light on an even surface wall As the optimal distance between the lamp and the lens was already set durin
24. wheel 2 20 Structure of the Fixture Light head fan Lamp holder Back panel AU of lamp holder NN es 17 Front cover i Static gobo wheel AO Had Ap E oo E ovo da QOO RO Reflector Color wheel B Color wheel Driver Board L Driver Board R Transformer Display Board Protect board Capacitance Ballast Bottom Fan Main PCB Electrical Diagram ae EI JE 2 H Troubleshooting No Light No Movement All Products This troubleshooting guide is meant to help solve simple problems If a problem occurs out the steps below in sequence until a solution is found Once the unit operates properly do not carry out following steps If the light effect does not operate properly refer servicing to a technician Response Suspect three potential problem areas the power supply the lamp the fuse 1 Power supply Check that the unit is plugged into an appropriate power supply 2 Ihe lamp Replace the old lamp with a new one with the same specifications See page 8 for replacing lamps 3 The fuse Replace the fuse See page 19 replacing the fuse No Response to DMX Response Suspect the DMX cable or connectors a controller malfunction a light effect DMX card malfunction 1 Check the DMX cable Unplug the unit change the DMX cable then reconnect to electrical power
Download Pdf Manuals
Related Search