E1 Manual PDF
Contents
1. User Manual Battery free wireless doorbell Model Number E1 yn Before operating please read this manual carefully Please follow the instructions to operate properly Transmitter Receiver C ROHS sy J 1 lmportant 1 Do not get the receiver wet 2 Do not disassemble repair or modify 3 Please screw in securely 4 Donot exceed electrical ratings 2 Attention Metal UPVC Door Surface Frame 1 Avoid locating Transmitter Receiver on or directly near metallic surface as this may reduce the oper ation range 2 When locating Transmitter onto a UPVC door frame always check the operating performance before final installation 3 Pack Contents Transmitter x1 Receiver x1 Adhesive Pad x1 User Manual x1 Screws x 2 Installation Instruction yN Please run atest before installation 1 Receiver Plug the receiver into the outlet The receiver will perform better if Keeping it away from electric equipment Try adjusting the location of the receiver according to the Range Guide Range guide De QOO Low 2 Transmitter Clean the surface where you intend to mount the transmitter and the back of the transmitter Before mounting the transmitter please run a test Put rec eiver and transmitter where you want to mount Close all doors when you test If the receiver does not sound please see Trouble Shooting DO NOT install transmitte2. X65 mm 79X44X32 mm 25 polyphony ring tones This marking indicates that this product should not be disposed with other household wastes throughout the EU To prevent possible harm to the environment or human health from uncontrolled waste disposal recycle it responsibly to promote the sustainable reuse of material resources To return your used device please use the return and collection systems or contact the retailer where the product was purchased They can take this product for environmental safe recycling Dimensions Weight Ring Tone
3. er Following the instructions in Learn Mode pair each additional transmitter to the receiver Note Maximum of 3 transmitters can be learnt to a single receiver a Add Additional Receiver Following the instructions in Learn Mode pair each additional receiver to the transmitter Note No limit to the number of receivers 6 Trouble Shooting 1 Make sure the receiver is plugged in Sere doesnot 2 Make sure the transmitter has been synchronized with receiver 1 Make sure receiver is plugged in Indicator light off 5 Check if receiver is in Learn Mode 1 Metal structures including door frames can result in reduced transmission range Avoid mounting transmitter or receiver on or near metal structures 2 Other electric equipment can cause radio interference that affects your receiver 3 Walls doors and ceilings will reduce the range Reduced range Attentions If the issue is still not resolved by the above methods please unplug the receiver and wait for about 3 seconds till the indicator light off then re plug it in If that does not solve the problem please contact customer service 7 Specifications Transmitter AC 100 240V Self powered 10 C 50 C 20 C 50 C Working range 80m open area RF Frequency 433MHz Sound Level 90dBA 3ft 1m Power Consumption lt 200mW Water Proof Operating Forces Specifications Receiver Power Supply Operating Temperature 78X50
4. r on UPVC door frames DO NOT install transmitter on Metal surface A Mount the transmitter with screws 1 Place the button mounting base on the required place of the wall screw the two screws into it 2 Carefully push the button down to the stop B Or mount the transmitter with adhesive pad J 1 Stick the transmitter to the wall by adhesive pad 2 Press the transmitter for 30 seconds Operation Instruction Indicator Light Q IRB Button Button Adjust sound volume Short press Button on the side ofthe unit to cycle through 3 class sound volume Silent Mode Long press Button for 5 seconds the indicator light will blink After 3 seconds of blinking the receiver will enter into silent mode Press Button or to exit silent mode Selectaring tone Short press Button Gon the side of the unit to cycle through 38 ring tones Leave it on whichever ring tone you like Re plug the Chime the tune will become Ding Dong Ding Dong Learn Mode Short press Button on the side of the unit for 5 seconds until the indicator light A blink to enter learn mode Press the transmitter twice The receiver will ring with indic ator light blink to confirm that transmitter has been paired to the Receiver Door chime kit will exit learn mode automatically Note Short press the Transmitter twice the Receiver will exit learn mode Add Additional Transmitt
Download Pdf Manuals
Related Search