HPS 685 HPS 685/55 HPS 685/55 E HPS 685 E
Contents
1. AUXILIAR POSITIVE CHECK FOR ARMING BLOCK AUXILIAR NEGATIVE CHECK FOR ARMING BLOCK SIREN COMMAND Max 1Amp ADDITIONAL MODULES COMMAND Max 100mA TEMPORIZED NEGATIVE COMMAND 30 SECONDS WINDOWS SLOPE COMFORT SYSTEM Max 1A HPS 685 rev 00 February 2006 pag 5 di 15 cop 00 99 0068510 EXAMPLES OF CONNECTIONS Type 1 connections with a car equipped whit original flashing YELLOW alarm YELLOW alarm HPS 685 to the left blinker WHITE YELLOW alarm to the right blinker 1N4004 Diode I to the front left blinker YELLOW alarm Il to the lateral left blinker Type 2 iwa to the rear left blinker connections with a car equipped whit HPS 685 I to the front right blinker igi i i YELLOW alarm original flashing in separated lines I to the lateral right blinker I to the rear right blinker WHITE YELLOW alarm YELLOW alarm to the left blinker YELLOW alarm to the blinker right WHITE YELLOW alarm Type a HPS 685 a to the POSITIVE d f the CDL cl O i o the command wire ol e closing connections with a car not equipped whit BLACK PINK alarm ae igi N o the command wire of le ope2. THE COMPANY IS NOT RESPONSIBLE FOR DAMAGES CAUSED BY PROPERTY OR PERSON RESULTING FROM THE OPERATION OF THE ANTIAGGRESSION To active it Alarm disarmed and key ON all the doors trunk and bonnet must be close and the internal light must be OFF Push the programming button for more of 5 seconds The activation of this function will be confirmed by 4 beep only with the siren installed To disable it Replace the precedent operation The deactivation will be confirmed by 1 beep only with the siren installed HPS 685 rev 00 February 2006 pag 13 di 15 cop 00 99 0068510 ALARM MAINTENANCE Our alarms are sophisticated systems characterised by a high level of reliability This reliability as well as time life may be furthermore incremented just adopting some precautions such as VEHICLE CLEANING should you clean the vehicle with high pressure devices hydrobeam or similar please protect the alarm before starting the cleaning In case of water infiltrations caused by hydrobeam this will authomatically invalidate the warranty MAIN MAINTENANCE all the repairs must be done by PATROL LINE assistance centres Tampering to the alarm by non authorised staff may invalidate alarm feasibility as well as your vehicle safety TECHNICAL FEATURES TENSION FEEDING WEIGHT 15V lt 30 sec 40 C 85 C 74x57 x 30 220 gr HPS 685 rev 00 February 2006 pag 14 di 15
3. ELECTRONIC ADVANCE LINE HPS 685 HPS 685 55 HPS 685 55 E HPS 685 E 12 VOLT Thanks for choosing one of our products Please read this manual carefully and Suitabledor_all the vehicles endowed keep it for any further reference at with original remote control to Close and open the CDL HPS 685 rev 00 February 2006 pag 1 di 15 cop 00 99 0068510 INDICE INDEX wes 2 ACOUSTIC SIGNALS IN ARMING AND i DISARMING 2 dAua AEV xe1 opiorel CEMOOOEIKTNG ELECTRIC WIRINGS FOR THE ALARM aya Aev ExXEI OpIOTE CEMOOOEIKTNG SUMMER FUNCTIONS QGAya Aev xe opioTel CEMOOOEIKTN CONNECTION DIAGRAM I 3 ANTIAGGRESSION FUNCTION only version CONNECTION EXAMPLE2Qd ud AEV EXE OPIOTE OENOOCEWG BS E u 12 ADJUSTEMENT ULTRASONIC SENSOR only ANTITHEFT FUNCTION only version 685 F 5 dAua version 685 55 2 dAua AEV Exel OpIOTE OEAIOOOEIKTNG ALARM MAINTENANCE2QdAuda AEV XEI OpIOTE OEAOOOEIKTI TECHNICAL FEATURES 14 COMMAND PROGRAMMING sere 7 FINAL TEST gt pdAyua AEV exer OpIOTE OEMOOOEIKTNG SOLUTION TO LITTLE PROBLEMSSpdAya Aev ye sai VICA GUIDE TO ACTIVATE THE FUNCT Ty Tq WORKING 2 dAua AEV Exe OpIOTE CEAOOOEIKTNG NEUTRAL TIME AND CHECK CONTROL2QdAua AEV EXE OpIOTE OEMOOOEIKTNG ALERT STATE gt pdAya AEV Exel OpIOTE OEAOOOEIKTNG PANICALARM uuiiin
4. cop 00 99 0068510 QUICKLY GUIDE TO ACTIVATE THE FUNCITONS FUNCTION ESTATE function ARMING ACOUSTIC SIGNAL ONLY WITH SIREN ANTITHEFT FUNCTION PANIC ALARM ONLY WITH SIREN SIREN EXCLUSION ONLY WITH SIREN ALARM SYSTEM DRIVER DOOR i STATE i OFF CLOSED OFF OPENED OFF I CLOSED VEHICLE KEY PROGRAMMING BUTTON PRESSED FOR 3 SECONDS PRESSED FOR 3 SECONDS PRESSED FOR 5 SECONDS PRESSED FOR 5 SECONDS PRESSED FOR 3 SECONDS PRESSED FOR 3 SECONDS AVAILABLE ONLY FOR THE VERSION HPS 685E THIS FUNCTION DEPEND FROMTHE ORIGINAL REMOTE CONTROL OF THE VEHICLE PATROLLIN ELECTRONIC ADVANCE Tel 0039 031 3354411 Bestidea s r l Via C Cant 15 C 22031 Albavilla CO ITALY Fax 0039 031 629417 E mail info bestidea it HPS 685 rev 00 February 2006 pag 15 di 15 cop 00 99 0068510
5. e little problems THE ALARM DOES NOT ARM THE ALARM ARM WHEN OPENING THE CAR THE ALARM DOES NOT EMIT ANY SOUND WHEN ARMING BEEP SIGNALLING AFTER ARMING THE VEHICLE DOES NOT SWITCH ON THE ALARM ARMS BY ITSELF Check the power supply of the alarm Verify that the mechanical key of the alarm is clockwise turned position ON Check that on the Green Black wire there is not a positive with the ignition key off If the problem is not solved repeat the syncronization of the original remote control Repeat the syncronization procedure of the original remote control Programm the acousting signalling of arming and disarming function through the programming button Verify that all the doors are well closed Verify the regulation of the crash sensor If the problem is not solved disconnect the sensors one by one and identify the defective one Verify that the alarm is disarmed LED off Verify the connection of the wire GREEN WHITE of the alarm We suggest a soft soldering Verify if the car is endowed with self closing function original function which close authomatically the cdl if is not opened a door HPS 685 rev 00 February 2006 pag 9 di 15 cop 00 99 0068510 User s Manual Thaks for choosing one of our products Please read this manual carefully and keep it for any further reference WORKING ALARM ARMING Press the CLOSING button of
6. he original remote control of the vehicle with the alarm following this procedure PROCEDURE OF FIRST PROGRAMMATION 1 Take off the ignition key and turn clockwise ON the mechanical key of the alarm The LED of the dashboard ON fixed and 10 quick flashings will confirm that the syncronization is started 2 Verify that the car is completely closed bonnet doors and boot and press the closing button of the original remote control 3 Once the flashings are over the switching off of the LED and an acoustic signal will confirm that the closing command has been memorized 4 Press the opening button of the original remote control 5 Once the flashings are over an acoustic signal will confirm that the opening command has been memorized and the procedure is finished HPS 685 rev 00 February 2006 pag 7 di 15 cop 00 99 0068510 PROCEDURE OF PROGRAMMATION AFTER THE FIRST ONE In case it would be necessary to erase the previous programmation it must be followed the procedure here under to repeat the syncronization 1 Turn anticlockwise OFF the mechanical key of the alarm 2 Switch on and leave on the ignition key 3 Turn clockwise ON the mechanical key of the alarm The LED of the dashboard ON fixed and 10 quick flashings will confirm that the syncronization is started 4 Switch off the ignition key verify that the car is completely closed doors bonnet and boot and press the closing button of the original remote con
7. iaaana 10 ALARM 2 dAua AEV Exe OpIOTE GEAOOOEIKTNG SIREN EXCLUSION if linked 5pdAya Aev yzl opioTel OEAIOOOEIKTNG MEMORIA DI ALLARME solo con sirena collegata S adya AEV Exe OpIOTE OEMOOOEIKTNG SIREN LIMITATION FOR CONSECUTIVE ACTIVATIONS POWER BACKUP only with the siren self powered u u 11 EMERGENCY MECHANICAL KEY2Q dAua AEV XEI OpIOTE CEMNOOOEIKTIG HPS 685 rev 00 February 2006 pag 2 di 15 cop 00 99 0068510 ELECTRIC WIRINGS FOR THE ALARM Red Wire Connect to a fused 12 volt positive line from the battery Power 12 Volt Black Wire Connect to battery negative or vehicle chassis Blinkers Yellow Wires Connect to the flasher wires right and left Alarm arming White Yellow Wire Connect to a wire of the blinkers command Blue Wire Connect to the door switch Perimeter protection Blue Red Wire Connect to the bonnet switch Ignition switch on Green Black Wire Connect to a positive under key These wires are from a potential free relay with a maximum current of 8A This relay is open when the alarm is triggered and the ignition key is on It may be used to control the fuel pump Engine Immobilization 8A Green White Wire Negative output with the alarm armed Connect to the Modules Command command wire for the optional modules Max current 100 mA Positive aux
8. iliary control to avoid the disarming For the wiring make reference to the technical sheet of the vehicle Auxiliary commands to unlock Negative auxiliary control to avoid the disarming For the Green wire wiring make reference to the technical sheet of the vehicle HPS 685 rev 00 February 2006 pag 3 di 15 cop 00 99 0068510 Programming button LED command Plant predisposition Extra siren command Windows rising COMFORT type command Opening switch control Closing switch control Opening engine control Closing engine control Grey Black Wire Brown Black Wire Violet Wire Black Blue Wire White Black Wire Connect to the GREY BLACK wire of the programming push button Connect to the black wire of the signalling LED Max 100mA Connection for the ultrasonic module HPS 55 Negative command of device in alarm Max 1Amp 30 seconds negative command useful for the windows rising if endowed with comfort system Max 1A Switch control for door opening command through key To be used only when the original blinkers flashing is missing Switch control for door closing command through key To be used only when the original blinkers flashing is missing Engine control for opening command trough remote control To be used only when the original blinkers flashing is missing Engine control for closing command trough remote control To be used only when
9. ll stop after the ninth or until the swiching on of the ignition key SIREN LIMITATION FOR CONSECUTIVE ACTIVATIONS If during the alert state the alarm sensors notice for 3 consecutive times a cause of alarm at the fourth cause of alarm the central unit will exclude its siren signalling the alarm only by the blinkers flashing During this phase is in any case active the electric engine block WARNING in case the ignition key is on the sound of the siren is restored HPS 685 rev 00 February 2006 pag 11 di 15 cop 00 99 0068510 POWER BACKUP The alarm is endowed with INSIDE batteries which guarentee its working even in case somebody cut the cable which connect the battery to the alarm wiring plant MECHANICAL EMERGENCY KEY In an emergency insert the emergency key into the alarm and turn it anti clockwise The alarm system is so completely switched off and the electric block engine is restored Funzioni Programmabili ACOUSTIC SIGNALLING WHEN ARMING AND DISARMING Through the original remote control the alarm is activated and this is confirmed by the blinkers flashing and the LED switched on Sometimes can be useful signal the arming and the disarming with an acoustic signalling not activated from the firm Acoustic signalling function To enable it With the alarm disarmed and the ignition key switched off check the correct lock of the vehicle bonnet doors and boot and if the vehicle is endowed with tempirized roof lamp wait
10. ning original flashing YELLOW BLUE alarm to the NEGATIVE command wire of the CDL switch closing VIOLET alarm to the NEGATIVE command wire of the CDL switch opening 1N4004 diode i to the front left blinker YELLOW aam i to the lateral left blinker to the rear left blinker i I lto the front blinker right YELLOW Type 4 alarm I to the lateral blinker right i i I to the rear blinker right connections with a car not equipped whit HPS 685 WE VELO Wale original flashing in separated lines BLACK BLUE alarm to the POSITIVE command wire of the CDL closing BLACK PINK alarm to the POSITIVE command wire of the CDL opening YELLOW BLUE alarm VIOLET alarm to the NEGATIVE command wire of the CDL switch closing 0 to the NEGATIVE command wire of the CDL switch opening HPS 685 rev 00 February 2006 pag 6 di 15 cop 00 99 0068510 ULTRASONIC SENSOR ADJUSTMENT version 685 55 only ADJUSTMENT OF THE ULTRASONIC SENSOR SENSITIVITY i Ultra sounds adjustment The sensitivity of the ultrasonic sensor can be modified working on the regulation trimmer of the module Turn the trimmer clockwise to increase the sensitivit and i Li se anticlockwise to decrease it Be careful a non correct adjustment can cause false i Al n alrms i Module HPS 55 COMMANDS PROGRAMMING Once the electric connections are over it is necessary to syncronize t
11. state is signalled by quick flashes of the LED installed on the dashboard HPS 685 rev 00 February 2006 pag 10 di 15 cop 00 99 0068510 PANIC ALARM If the original remote control repeat the closing signalling as described in the paragraph optional functions available when the alarm is armed it is possible to make the siren sounding through another pression of the closing button of the original remote control ALARM In case of tampering the system weill emit an optic acoustic signalling blinkers flashing and siren sound for 30 seconds SIREN EXCLUSION If the original remote control repeat the closing signalling as described in the paragraph optional functions available while the alarm is still sounding it s possible to stop the siren sound without disarming the alarm through another pression of the closing button of the original remote control MEMORY OF ALARM If the central unit notices one o more causes of alarm they are signalled when disarming through another flashing of the blinkers and by a number of beep as per the alarms occurred if the acoustic signalling function is programmed To verify which type of alarm has occurred press for 1 second the programming button Compare the number of beeps emitted by the alarm with the following table N Beep CAUSE 1 DOOR BONNET AND BOOT SWITCH LINE 3 ULTRASONIC SENSOR 4 ENGINE SWITCHING ON ATTEMPT Note The signalling of the LED wi
12. the original blinkers flashing is missing For the wires connection take a look to the technical sheet of the vehicle HPS 685 rev 00 February 2006 pag 4 di 15 cop 00 99 0068510 WIRING DIAGRAM CONNECTION HPS 55 Connect the ultrasonic capsules H PS 685 following the right connector colors murana ara 10 9 s s s l2 li HPS 55 ULTRASONIC SENSOR WHITE BLACK Pos 4 GREEN WHITE Pos 12 ENGINE BLOCK MAX 8A GREEN WHITE Pos 13 PROGRAMMING BUTTON ex trunk l CONNECTION FOR THE VEHICLE THE ORIGINAL FLASH LAMPS Lock and unlock check USE THEM ONNLY IF THERE ISN T THE ORIGINAL BLINKER FLASHING trough the external lock Rev 00 di May 2006 OPTIONAL BUTTON i l GREY BLACK Pos 18 Pos 3 BLUE P DOORS BUTTON DIODE t BONNET BUTTON BLUE RED da ready presen WITHOUT PURPLE Pos 6 YELLOW BLUE Pos 7 BLACK PINK Pos 8 BLACK BLUE Pos 19 RED Pos 11 GREEN BLACK Pos 14 BLACK Pos 15 YELLOW Pos 9 YELLOW Pos 10 WHITE YELLOW Pos 17 WHITE Pos 16 GREEN Pos 20 WHITE RED Pos 1 BROWN Pos 5 MARRONE NERO Pos 2 Connect the emergency wired key POSITIVE FIXED POSITIVE UNDER KEY NEGATIVE FIXED al INDICATOR LIGHTS POSITIVE COMMAND OF ARMING AND DISARMING
13. the remote control The arming will be confermed by 3 acoustic signals if programmed and if installed Switching on of the LED on the dashboard Switching on of the blinkers of the vehicle Activation of the electric engine immobilization Activation of the modules output windows rising ultrasounds ecc ALARM DISARMING Press the OPENING button of the remote control The disarming will be confermed by 1 acoustic signal if programmed and if installed Switching off of the LED on the dashboard Switching on of the blinkers of the vehicle Deactivation of the electric engine immobilization Deactivation of the modules output windows rising ultrasounds ecc INIBITION TIME amp SYSTEM CHECK Once the blinkers flashing is over the alarm system enters its inibition time for approximately 30 seconds as signalled by the fixed light of the LED During the inibition time it is possible to test the good working of the alarm sensors without triggering the siren Bumping into the vehicle opening the doors or the boot perimetral buttons a short acoustic signal will confirm that the sensor has noticed the alarm During this phase the alarm does not enable the high power siren but provide anyway to block the engine WARNING should the ignition switch on the siren sound will immediately start ALERT STATE At the end of the inibition time 30 seconds the alarm system is ready to signal any theft attemp The alert
14. tive the siren if installed and the blinkers flashes for 20 seconds pre alarm finally will be active also the engine block of the vehicle To stop the antiaggression function it s necessary to press the programming button IN ANY CASE THE COMPANY IS NOT RESPONSIBLE FOR DAMAGES CAUSED BY PROPERTY OR PERSON RESULTING FROM THE OPERATION OF THE ANTIAGGRESSION To active it Alarm disarmed and key ON open the drive side door Push the programming button for more of 5 seconds The activation of this function will be confirmed by 3 beep only with the siren installed To disable it Replace the precedent operation The deactivation will be confirmed by 1 beep only with the siren installed ANTITHEFT FUNCTION only version 685 E IMPORTANT BEFORE TO PROGRAM THIS FUNCTION READ CAREFULLY THE FOLLOWING NOTE ATTENTION IN CASE TO ACTIVATION OF THIS FUNCTION THE COMPLIANCE WITH THE EUROPEAN DIRECTIVE 95 56 S NOT MORE VALID ATTENTION IN CASE TO ACTIVATION OF THIS FUNCTION THE ENGINE BLOCK CAN BE ACTIVED WHEN VEHICLE IS MOVING If programmed when the door is opened and closed with the key ON the dashboard LED turn ON the function start After 50 seconds the alarm active the siren if installed and the blinkers flashes for 20 seconds pre alarm finally will be active also the engine block of the vehicle To stop the antitheft function it s necessary to press the programming button IN ANY CASE
15. trol 5 Once the flashings are over the switching off of the LED and an acoustic signal will confirm that the closing command has been memorized Press the opening button of the original remote control 7 Once the flashings are over an acoustic signal will confirm that the opening command has been memorized and the procedure is finished Optional Functions Available In case the original remote control has more buttons and pressing for a second time the closing button the blinkers flash like the first closing it is possible to syncronize the following extra functions Panic Alarm Siren Exclusion To enable them When switching on through the mechanical key during the 10 quick flashings of the blinkers beginning of the commands programming phase press for 3 seconds the programming button of the alarm To disable them Ripeat the phase of programming without pressing the programming button FINAL TESTING Once the programmations are over and once verified that the car is completely closed press the closing button of the original remote control and verify that the LED on the dashboard is ON Test all the functions and verify the regulation of the crash and ultrasonic sensors Press the opening button of the original remote control and verify that the LED of the dashboard switches off HPS 685 rev 00 February 2006 pag 8 di 15 cop 00 99 0068510 SOLUTION TO LITTLE PROBLEMS Here under a simple and useful guide to solv
16. until also this one is switched off Press the programming button for more than 3 seconds The activation of the function is signalled by 5 beeps if the siren is installed To disable it Ripeat the operations described above The deactivation of the function will be signalled by 1 beep if the siren is installed ESTATE FUNCTION If you need to leave the windows open avoiding false alarms because of the ultrasonic sensors you can enable the estate function not activated from factory Estate function To enable it With the alarm disarmed and the ignition key turned off open the door on the driver s side Press the programming button for more than 3 seconds The activation of the function will be confirmed by 2 beeps if the siren is installed To disable it Ripeat the operations described above The deactivation of the function will be signalled by 1 beep if the siren is installed HPS 685 rev 00 February 2006 pag 12 di 15 cop 00 99 0068510 ANTIAGGRESSION FUNCTION only version 685 E IMPORTANT BEFORE TO PROGRAM THIS FUNCTION READ CAREFULLY THE FOLLOWING NOTE ATTENTION IN CASE TO ACTIVATION OF THIS FUNCTION THE COMPLIANCE WITH THE EUROPEAN DIRECTIVE 95 56 IS NOT MORE VALID ATTENTION IN CASE TO ACTIVATION OF THIS FUNCTION THE ENGINE BLOCK CAN BE ACTIVED WHEN VEHICLE IS MOVING If programmed when the key is turned ON the dashboard LED turn ON the function start After 50 seconds the alarm ac
Download Pdf Manuals
Related Search