WIRELESS SMOKE DETECTOR
Contents
1. and upon returning from vacation or when no one has been in the household for several days Test each wireless smoke detector to be sure it is installed correctly and operating properly DO NOT use an open flame to test this wireless smoke detector You may ignite and damage the wireless smoke detector or your home If the wireless smoke detector does not sound please check the battery and signal level using ELDES Configuration Tool software vata wile 8 Test all wireless smoke detectors weekly to ensure proper operation 5 2 Battery Replacement 1 Turn EWF1 counter clockwise to detach it from the mounting 7 plate Ea 9V battery 2 Gently pull down the wireless smoke detector 3 Remove the old battery from the battery pocket 4 Postition the new 9V battery according to the appropriate battery slot positive negative terminals indicated on the enclosure of EWF1 Ensure the plastic battery holder is fully depressed when the battery has been fitted 5 Using the TEST button test the wireless smoke detector to verify if it is operational See 4 1 Testing EWF1 6 Re attach the wireless smoke detector to the mounting plate by turning the wireless smoke detector clockwise until it snaps into place EN EWF1 Manual v1 1 Naty wile Only Primary 9V Lithum 1200mAh battery can be used Install only new high quality and unexpired batteries Bute B The battery must be removed if th2. default and try again See chapter 5 3 Restoring Default Parameters for more details EWF1 Manual v1 1 5 g Zone Tamper Alarm Quege Wireless Device Management Device ID 58122812 A EWF1 D 02000011 Tamper ALARMI G3 iid Soks Nesli Nese Device Type EWF1 CONNECTED Search ee Temperature 30 C Battery Level 0 Signal Level 0 Device ID x amp pat a 4 1 Interconnection The interconnection feature automatically links all wireless smoke detectors to each other that are connected to the same alarm system unit When any EWF1 detects smoke it sounds the alarm and sends the signal to the alarm system that causes an instant alarm along with the rest of EWF1 wireless smoke detectors The device that detected smoke will auto reset when the smoke clears while the rest of EWF1 detectors will sound according to the set time period by default 60 seconds By default the interconnection feature is enabled but can be disabled using ELDES Configuration Tool software 5 MAINTENANCE 5 1 Testing EWF1 e The TEST button verifies if EWF1 is operational Firmly push the TEST button and the wireless smoke detector will sound a loud beep The alarm will stop sounding after releasing the TEST button When testing EWF1 using ELDES Configuration Tool software the detector will provide short beeps e Stand at arm s length from the wireless smoke detector when testing Test wireless smoke detectors weekly
3. loose particles interfere with wireless smoke detector operation umd wile Incorrect placement will result in a decrease of operational effectiveness 4 EN EWF1 Manual v1 1 4 INSTALLATION AOLA Before installing the wireless device we highly recommend to refer to RADIO SYSTEM INSTALLATION AND SIGNAL PENETRA TION manual located at www eldes It download Never install in the following Recommended x locations EI facethefrontside of the D e inside the metal cabinet D aat aeaa wireless device towards the MES closer than 20cm 0 66ft OH inside the building the front side of EPIR3 from the metal surface cS 0 5mto150m e keep the distance 0 5 to 30m and or power lines 1 64 to 492 13ft 1 64 to 98 43ft inside the Wile AE ERS building 0 5 to 150m 1 64 to x device 492 13ft inopen areas Recommended 0 5to 30m 1 64 to 98 43ft inside the building a 4 0 5to150m 1 64 to 492 13ft in open areas Wireless Wireless device antenna face the front side of the wireless device towards the antenna keep the distance 0 5 to 30m 1 64 to 98 43ft inside the building 0 5 to 150m 1 64 to 492 13ft in open areas 1 Detach the mounting plate by turning it counter clockwise from he back of EWF1 see Fig No 5 5 2 Secure the mounting plate to ceiling or wall with mounting screws see Fig No 5 3 Lift to open the battery pocket door see Fig No 7 4 Insert the
4. CIFICATIONS 2 1 Electrical amp Mechanical Characteristics Detection type Photoelectric chamber Alarm sound level 85dB at 3m 85dB at 9 84ft Battery Primary 9V Lithum 1200mAh ANSI NEDA 1604LC Number of batteries 1 Battery operation time 18 months Wireless band ISM868 ISM915 Wireless communication range Up to 30m 98 43ft in premises up to 150m 492 13ft in open areas Range of operating temperatures 5 45 C 41 113 F Humidity 0 90 RH 0 40 C 0 90 RH 32 104 F non condensing Sensitivity to smoke 3 0 6 0 Obs m Smoke detector lifetime 10 years Dimensions 110mm 0 36ft Compatible with alarm systems ELDES Wireless This operation time might vary in different conditions AHH We strongly recommend using EVE CR9V P or Energizer LA522 battery 2 EN EWF1 Manual v1 1 2 2 Main Unit amp LED Functionality TEST Button for testing button for testing and restoring default parameters if RESET button not available LED EWF1 status indication SIREN Built in speaker for audio alarm indication RESET Button for restoring default parameters E FRONT SIDE BACK SIDE RESET button BATTERY J N NS Unavailaible on some EWF1 models 3 PLACEMENT 1 Place the detector as close to the center of the ceiling as possible If this is not practical mount no closer than 10cm 0 33ft from
5. D Q Minimum required smoke Dini Bedroom detector locations ining Room Kitchen a O Recommended additional smoke detector locations 3 2 Typical Multi Story or Split Level House Install a wireless smoke detector on the ceiling or wall inside each El bedroom and in the hallway outside each separate sleeping area If a bedroom area hallway is more than 9m 29 53ft long install a wireless smoke detector at each end Please install a wireless smoke detector on the top of a first to second floor stairwell Not N LEGEND Bedroom Bedroom Minimum required smoke detector locations O Recommended additional smoke detector locations O Living Dining Room Room Basement 3 3 Incorrect EWF1 Placement DO NOT place EWF1 in the following locations e Near appliances or areas where normal combustion regularly occurs kitchens near furnaces hot water heaters Use specialized wireless smoke detector with unwanted alarm control for this areas e In areas with high humidity like bathrooms or areas near dishwashers or washing machines Install at least 3m 9 84 ft away from these areas e Near air returns or heating and cooling supply vents Install at least 1m 3 28ft away from these areas The air could blow smoke away from the detector interrupting its alarm e Inrooms where temperatures may fall below 5 C 41 F or rise above 45 C 113 F e Inextremely dusty dirty or insect infested areas where
6. a wall or corner Also if local codes allow install the detectors on walls between 10 and 30cm 0 33 and 0 98ft from ceiling wall intersections Install a minimum of two wireless smoke detectors in every house no matter how small the house is Place a detector in each room that is divided by a partial wall either coming down from the ceiling at least 20cm 0 66ft or coming up from the floor ALLA For best protection we recommend that you install a wireless smoke detector in every room Recommended EWF1 placement locations E ue Olm Ceiling 0 33ft I oim Acceptable 0 3 aft here LZ M NEVER en HERE _ 0 3m 0 98 ft Top of detector Max 0 9m 2 95 ft 0 9m 2 95 ft acceptable here HORIZONTAL DISTANCE Wall Wiert A Measurements shown are to the closest edge of the detector EWF1 Manual v1 1 E 3 1 Typical Single Story House Install a wireless smoke detector on the ceiling or wall inside each bedroom and in the hallway outside each separate sleeping area If a bedroom area hallway is more than 9m 29 53ft long install a wireless smoke detector at each end If there is a basement Install a wireless smoke detector on the basement ceiling at the bottom of the stairwell 2 Bedroom O Bedroom Living Room O 5 N Family Room LEGEN
7. battery into the battery pocket considering the po larity terminals indicated on the enclosure of EWF1 Ensure the battery is securely connected Red LED may flash briefly when he battery is being installed ee Mounting plate Mounting slot au PE l Close the battery pocket door by snapping it into place l Screws Position the smoke detector to the mounting plate by turning it clockwise to lock into place Note that the device will not lock C l into the mounting plate without the battery being present in I he battery pocket 7 Push the TEST button to verify if the wirless smoke detector is operational See 4 1 Testing EWF1 8 Bind the device to the alarm system using ELDES Configuration Tool software Open Wireless Device Management section and enter a 8 digit wireless device ID located on the EWF1 enclosure and click the Add button see Fig No 6 The device can also be bind by sending a corresponding command via SMS text message For more details please refer to the software s HELP section and ELDES alarm system installation manual 9 Upon the successful binding process EWF1 device icon be comes visible in Wireless Device Management section as well as Battery Level and Signal Level see Fig No 6 10 EWF1 wireless smoke detector is ready for use Battery pocket door ALH If you are unable to bind the wireless device please restore the parameters of the wireless device to
8. can be interfere with other devices and cause any potential danger e DONOT use the system with medical devices e DONOT use the system in hazardous environment e DONOT expose the system to high humidity chemical environment or mechanical impacts e DONOT attempt to personally repair the system the product must not be disposed of together with household waste To prevent possible harm to human health and or the environment the product must be disposed on in an approved and environmentally safe recycling process For further infor mation on how to dispose of this product correctly contact the system supplier or the local authority responsible for waste EN disposal in your area Dd The WEEE Waste Electrical and Electronic Equipment marking on this product see left or its documentation indicates that Copyright ELDES UAB 2014 All rights reserved It is not allowed to copy and distribute information in this document or pass to a third party without advanced written authori zation by ELDES UAB ELDES UAB reserves the right to update or modify this document and or related products without a warning Hereby ELDES UAB declares that wireless smoke detector EWF1 is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC The declaration of conformity may be consulted at www eldes lt EN EWF1 Manual v1 1 Made in the European Union www eldes lt
9. e device is not in use Fat wile In order to avoid fire or explosion hazards the system must be used only with approved battery Special care must be taken when connecting positive and negative battery terminals Dispose old batteries only into special collection sites Do not charge disassemble heat or incinerate old batteries ALILA The battery status can be monitored in real time using ELDES Configuration Tool software The system sends an SMS message to the preset user phone number as soon as the battery level runs below 5 5 3 Restoring Default Parameters 1 Remove the battery from EWF1 2 Press and hold the RESET button 3 Insert the battery back to EWF1 4 Hold the RESET button until you hear a short beep 5 Release the RESET button On some EWF1 models the RESET button is not available On such EWF1 devices the reset process is as follows 1 Remove the battery from EWF1 2 Wait for 45 seconds 3 Press and hold the TEST button 4 Insert the battery back to EWF1 5 Hold the TEST button for 10 seconds or more 6 Release the TEST button Lute EWF1 built in speaker will sound while pressing and holding the TEST button Please ignore the sound 5 4 Cleaning Clean the wireless smoke detector at least once a month to remove dust dirt or debris Using the soft brush or wand attachment of a vacuum cleaner vacuum all sides and cover of wireless smoke detector Be sure all the vents are free of debris If n
10. ecessary use a damp cloth to clean wireless smoke detector cover ALH Do not attempt to remove the cover to clean inside the wireless smoke detector This will void your warranty EWF1 Manual v1 1 7 6 ADDITIONAL INFORMATION Limited Liability The buyer must agree that the system will reduce the risk of fire theft burglary or other dangers but does not guarantee against such events ELDES UAB will not take any responsibility regarding personal or property or revenue loss while using the system ELDES UAB liability according to local laws does not exceed value of the purchased system ELDES UAB is not affiliated with any of the Internet pro viders therefore is not responsible for the quality of Internet service Manufacturer Warranty This device carries a 24 month warranty by the manufacturer ELDES UAB Warranty period starts from the day the system has been purchased by the end user The warranty is valid only if the system has been used as intended following all guidelines listed in the manual and within specified operating conditions Receipt must be kept as a proof of purchase date The warranty is voided if the system has been exposed to mechanical impact chemicals high humidity fluids corrosive and hazardous environment or other force majeure factors Safety instructions Please read and follow these safety guidelines in order to maintain safety of operators and people around e DONOT use the system where it
11. eldes F User Manual v1 1 Compatible with e ESIM264 v7 11 30 and up EWT1 16 14 and up e ESIM364 v02 04 01 and up e EPIR2v01 01 02 and up e EPIR3all versions Main Features e Photoelectric sensor for slow smouldering fires e Quick fix mounting plate for easy installation e TEST button e LED operation indicator e Non radioactive technology for environmental friendly e Built in speaker for audio alarm indication e Highand stable sensitivity e Auto reset when smoke clears EWF1 is a wireless photoelctric type smoke detector intended to use with ELDES alarm systems Photoelectric smoke detectors are gener ally more effective at detecting smouldering fires which smoulder for hours before bursting into flame An optical method is used for the detection of visible smoke When the concentration of smoke in the optical chamber exceeds a given threshold EWF1 sounds the alarm and sends out a signal to the ELDES alarm system using the wireless connection and the system triggers the alarm By default when more than one EWF1 device is used the system will automatically activate the interconnection feature See 4 1 Interconnection ESIM264 EPIR2 and EPIR3 alarm systems support up to 16 EWF1 devices while ESIM364 up to 32 EWF1 devices The maximum wireless connection range is 150m 492 13ft in open areas 1 PACKAGE CONTENT qty 1 qty 1 qty 1 qty 2 3 Primary 9V Lithium 1200mAh battery 4 Screws 2 TECHNICAL SPE
Download Pdf Manuals
Related Search