LRB 7x50
Contents
1. 20 10 QUALITY CERTIFICATE LRB 7x50 with serial number has passed the quality inspection Production date Quality Inspector Purchase date 21 NEWCON OPTIK Printed in Canada2. distance 0 Press Action button to switch along this string Last 10 measurements are kept in the System even when it is off CL Clears results of all measurements The System keeps the selected parameters until they are reset 5 5 Additional display information Laser active indicator 6 Fig 3 flashes when the unit emits laser radiation A LOW BATTERY pictogram appears on LCD when voltage of the battery voltage drops below 7 2 volt At this point the System is still fully functional as it can operate at the voltage level above 7 volt 14 6 STORAGE AND MAINTENANCE The unit is a sophisticated precision optical instrument equipped with laser and electronics Therefore it should be handled with due care e Keep away from direct sunlight e Avoid impacts jolts dust moisture and sharp changes of temperature e Do not use the device at temperatures higher than 50 C 122 F e Do not touch optical surfaces Doing so may damage the anti reflection coating e Clean optical surfaces only with professional camera lens cleaning supplies e Clean the exterior of the unit with a soft clean cloth e Keep the unit away from heating appliances and central heating e Remove the battery when storing the device for long time e All repair works must be performed by an authorized service only 15 7 TROUBLESHOOTING Ranging does not work The display is transparent Check the charge of the battery Replace it if it
3. is weak Ranging does not work The display indicates results of the last measurement Wait for 10 seconds until the display becomes transparent and press the Action button again Black dots are visible on LCD Liquid Crystal Display may have small black dots scratches and other blemishes inherited from the manufacturing process These flaws are strictly regulated by number area and location and do not degrade the product s measurement capabilities Range measurement cannot be obtained e Make sure that neither your hand nor finger is blocking objective lens laser emitting lens or receiver lens e Holdthe unit firmly avoid hand tremor while pressing the Action button e Check that the target is within measuring range of the device and the gating mode does not cut it off 8 WARRANTY NEWCON warrants this product against defects in material and workmanship for one year from the date of the original purchase Longer warranty is available subject to the terms of the specific sales contract Should your Newcon product prove to be defective during this period please deliver the product securely packaged in its original container or an equivalent along with the proof of the original purchase date to your Newcon Dealer Newcon will repair or at its option replace with the same or comparable model the product or part thereof which on inspection by Newcon is found to be defective in materials or workmanship What T
4. N NEWCON OPTIK Operation Manual LRB 7x50 LASER RANGE FINDER BINOCULAR 105 Sparks Ave Toronto ON M2H 2S5 IMPORTANT INFORMATION Read prior to activation You have just purchased a sophisticated electro optical device that emits invisible laser radiation To operate it properly please read this manual carefully e NEVER direct laser beam at the eyes of people or animals e NEVER aim the unit at the Sun or bright sources of light e NEVER subject the unit to impacts e NEVER transport the unit without its case e NEVER disassemble the unit This may be hazardous for you due to high voltage currents in the system e ALWAYS keep the unit out of children s reach e ALWAYS remove the battery when the device is not in use for a long period e ALWAYS store in a dry place e Caution use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure Caution use of optical instruments such as binoculars loupes mirrors lenses etc with this product increases risk of ocular damage Note Avoid eye exposure to direct laser beam or its close reflection Prevent bright light from focussing through the eyepiece dE TE A CONTENTS BRIEF DESCRIPTION DEVICE APPEARANCE DELIVERY SET SPECIFICATIONS OPERATION INSTRUCTIONS 5 1 Installing the battery 5 2 Maximum distance 5 3 Distance Measurement 5 4 Mode selecti
5. TO ON CANADA M2H 255 THIS PRODUCT COMPLIES WITH CFR 21 1040 10 1040 11 MADE IN CANADA 4 MODE READY TARGET REFLECTION LOW MED HIGH Fig 3 Liquid Crystal Display LCD 1 Low battery indicator 2 Reticle either or 1 3 Units of measurement 4 Measurement result 5 Target quality indicator 6 Laser active indicator 3 DELIVERY SET Standard delivery set for LRB 7X50 includes Device Carrying case Neck strap Cleaning cloth User s manual Warranty card 9V battery 1 pe 1 pe 1 pe 1 pe 1 pe 1 pe 1 pe 4 SPECIFICATIONS Optics Magnification Objective lens diameter Exit pupil diameter Field of view Type of coating Interpupillary distance Dioptre adjustment range Range Finder Laser Measuring range Accuracy Meters Yards display Last 10 measurements recall Reticle TX 50 mm 7 1 mm 5 Fully multi coated optics 58 72 mm 4 Class 1 eye safe 905 nm 20 1 500 m 1 m Yes Yes or O Power Battery Battery capacity Low Battery indicator Environmental Operational temperature range Storage temperature range Mechanics Tripod thread Weight without battery Dimensions 9V Alkaline Min 5 000 measurements Continuous operation Yes 25 50 C 13 122 F 45 65 C 49 149 F Ya x 20 TPI 1 3kg 210x150x60 mm 5 OPERATION INSTRUCTIONS 5 1 Installing the battery Unscrew the s
6. crew and open the battery compartment cover 10 Fig 2 Connect a battery to the battery snap and insert it into battery compartment Close the cover and tighten the screw The unit is fully operational when battery voltage is higher than 7V A LOW BATTERY warning is displayed when battery voltage falls below 7 2V After changing the battery it is recommended to run the CL CLEAR mode refer mode selection procedure to clear the on board memory If this is not done the recall function will not work properly The System should be powered with Alkaline or Lithium batteries capable to sustain current drain up to 150 mA 5 2 Maximum distance The maximum measuring range for most objects is 1512 meters The maximum measured distance will vary greatly depending on the reflectivity of the target and weather conditions Target reflectivity depends on its color surface finish size shape position in relation to the laser beam etc Bright target colors are more reflective than darks A polished surface is more reflective than a rough one Larger targets reflect better than small ones Ranging a target perpendicular to the laser beam provides better results than the one positioned at a sharp angle to the beam Weather conditions that influence air transparency rain fog snow mist reduce maximum range Bright sunny days will reduce performance as well as IR sun radiation may cover reflected laser pulses While t
7. he unit will measure through many glass types measuring through glass may reduce accuracy 11 Natural hand tremor decreases the accuracy of long distance ranging Using of a tripod is highly recommended 5 3 Distance Measurement When the Rangefinder is off the LCD Display is blank transparent Pressing any of the operating buttons activates the System and the Display At start the System assumes READY mode of operation and word READY appears on the LCD Pressing Action button 5 Fig 1 at this point triggers a distance measuring and the result will be displayed 4 3 Fig 3 If measurement is unsuccessful then four dashes will appear in the numerical area For a reliable measurement the target must be more than 20 m away 5 4 Mode selection Pressing MODE button 4 Fig 1 in READY mode brings the System to mode selecting Every pressing ofthe Mode button brings the next mode name to the LCD so that user can scan through all available modes When new mode appears on LCD it flashes to select it press Action button The following sequence of modes is available Displayed 8 Fun D Function Y Select Yards for distance measurement M Select Meters for distance measurement l Reticle shape O Reticle shape Displays the last 10 measurement results starting from the last one Results are numbered and displayed in the following order rEC1 distance 1 rEC1 rEC2 distance 2 rECO
8. his Warranty Does Not Cover NEWCON is not responsible for warranty service should the product fail as a result of improper maintenance misuse abuse improper installation neglect damage caused by disasters such as fire flooding lightning improper power supply or service other than by aNEWCON Authorized Service 18 Postage insurance and shipping costs incurred while presenting your NEWCON product for warranty service are your responsibility If shipping from North America please include a cheque or money order payable to NEWCON OPTIK for the amount of US 15 00 to cover handling and return shipping 9 CUSTOMER SUPPORT Should you experience any difficulties with your NEWCON OPTIK product consult this manual first If the problem remains unresolved contact our customer support department at 1 416 663 6963 or toll free at 1 877 368 6666 Our operating hours are 9 am 5 pm Monday Friday Eastern Standard Time At no time should equipment be sent back to Newcon without following the instructions of our technical support department NEWCON OPTIK accepts no responsibility for unauthorized returns To locate NEWCON Authorized Dealer call Tel 1 416 663 6963 Fax 1 416 663 9065 Email newconsales newcon optik com Web www newcon optik com The defective products should be shipped to From the USA only 2498 Superior Ave Cleveland OH 44114 From all other countries 105 Sparks Ave Toronto ON M2H 285 CANADA
9. on 5 5 Additional display information STORAGE AND MAINTENANCE TROUBLESHOOTING WARRANTY CUSTOMER SUPPORT QUALITY CERTIFICATE CAREFULLY READ ALL THE INSTRUCTIONS PRIOR TO USE FAILURE TO OBEY THE INSTRUCTIONS WILL VOID THE WARRANTY AND MAY CAUSE INJURY 1 BRIEF DESCRIPTION LRB 7x50 Laser Rangefinder Binoculars System is an advanced laser range finder system that enables instant distance measurements Outstanding optics provide a sharp clear image under any observation conditions The unit utilises time of flight method of distance measurement The System sends invisible eye safe laser pulses to the target The returned pulses are captured by the digital circuitry The time difference is used to calculate the distance to the target The unit complies with CFR 21 Part 1040 10 and Part 1040 11 Key Features Modern digital circuitry allows targeting through most types of glass Meters Yards display Last 10 measurements recall Selectable reticle shape or U 2 DEVICE APPEARANCE Fig 1 Front view 1 Eyepieces 2 Objective lens 3 Dioptric adjustment rings 4 Mode button 5 Action button 6 Body of the device 7 Rubberized grip Fig 2 Rear view 8 Interpupillary distance adjustment lever 9 Model number plate 10 Identification and certification label battery compartment cover at the bottom ce Patent Pending Newcon Optik 105 SPARKS AVE TORON
Download Pdf Manuals
Related Search