Home

Peak Performer 1 FID (920- Series) User Manual

Contents

1. Figure 48 The Completed Chromatogram 7 4 Flow Venting and Balancing Several problems can arise in the development of the chromatogram e Presence of compounds that may be damaging to the detector e Disproportionate peak sizes e Length of analysis Several models of Peak analyzers are equipped with one or two valve plumbing arrangements to handle these situations Often a second valve is used to perform cutting actions at particular times during the chromatogram redirecting the column effluent towards a safe flow controlled vent outlet During the cutting action it is necessary to maintain pure gas flow to the detector This pure gas flow is provided by an additional branch on the internal carrier gas main line feeding other ports on the valve Ultra high purity flow control components can be bulky and expensive To diminish installed cost of flow control components Peak has chosen a different method based upon flow restrictors to create a flow divider A typical flow divider is shown in Figure 50 Page 69 Peak Performer 1 Users Manual CARRIER GAS MAIN LINE FLOW ADJUSTMENT NEEDLE VALVE MAIN FLOW LIMITER 110 sccm 60 PSIG EXCESS FLOW VENT TO DETECTOR DETECTOR BALANCE RESTRICTOR Figure 49 Flow Divider Schematic The gas flow path to the detector is extremely clean and free of moving parts The gas passing from the main flow limiting restrictor can be split to follow both
2. Figure 42 System configuration diagram with basic connections 6 6 1 RS232 to RS485 Converters There are numerous manufacturers of RS232 to RS485 converters and the selection of the converter must be determined by the system engineer designer to meet unique requirements Page 64 Peak Performer 1 Users Manual 7 0 Chromatographic Principles As an analytical system the PP1 FID performs four primary functions e Sample injection e Component separation e Component analysis e Integrated microprocessor system control with operator and data interface 7 1 Sample Injection A standard air actuated VICI injection valve is used to inject samples Standard FID analysis methods use stainless steel 5 cc sample loops 7 2 Carrier Gas Purification Chromatographic instrument detection limit is directly related to carrier gas purity Improved carrier gas purity enables improved sensitivity Typical Nitrogen 99 999 Carrier Gas Specifications Pre Purification High Pressure Cylinder or Liquid Dewar Gas Type Ne Ar He alternative Consequently the analyzer s minimum detectable quantity MDQ would be quite high gt 10 ppm unless the carrier gas is purified Peak recommends use of the best quality heated metal getter purifier available for carrier gas purification This style of purifier typically has a hot catalyst element ahead of the heated getter material for complete removed of methane hydrocarbon CH4 a
3. The Peak Performer 1 has a fully integrated stand alone microprocessor operating system Key functions of the operating systems include detector and temperature control data collection and analysis and operator data interface ingle or Multiple 1 8 Columns Temperature range Ambient 50 C gt 295 C 160 watts maximum Page 7 Peak Performer 1 Users Manual 2 0 Installation Considerations 2 1 Unpacking Instructions Remove the Peak Performer 1 from the packing material or traveling case taking care to not scar the exterior surfaces of the analyzer set the analyzer on a firm even surface and remove the protective plastic wrap Each analyzer ships with adequate supplies for installation Be certain to remove the installation accessories tubing power cord compression fittings etc from the packing materials Remove the sleeve containing the Certificate of Conformity and Installation CD from the analyzer top panel All shipping materials are reusable please recycle these materials appropriately 2 2 General Considerations e Analyzer size is 26 L x 17 W x 7 H e Maximum operating environment for the PP1 analyzer is 30 C e Minimum operating environment for the PP1 analyzer is 15 C e Power consumption is 160 watts maximum e Fuse size is 2 5 ampere 250 VAC 5 x 20 mm SLO BLO e Free air flow for adequate ventilation to the rear of the unit is required e Communication between the PP1 and your PC
4. 9 Vacuum insulation debris from the FID Module area and loosen the methanizer from the block with long nosed pliers 10 Uncouple the methanizer inlet and outlet 1 16 VICI fittings from the VICI T s Inlet Outlet Figure 81b Removing outlet 1 16 fittings from the VICI T s Page 100 11 12 13 14 19 16 17 18 19 20 21 22 23 24 20 26 27 Peak Performer 1 Users Manual Remove the methanizer from the methanizer heater block Install the replacement methanizer into the heater block Re install the methanizer block Connect and fully tighten the 1 16 VICI fittings to the VICI T s Re install the FID Oven insulation taking care to not disturb the heater and thermocouple leads Re install the FID oven cover making sure that the heater and thermocouple leads are not stressed and exit through the lower notch in the FID oven cover Vacuum any loose insulation remaining in the chassis Re install the PP1 top cover Plug in the AC power cord re energize the analyzer and turn on the Methanizer and Column heater zones Adjust the Methanizer heater zone temperature to 375 C Allow the FID FLAME temperature to reach a minimum reading of 85 C Pressurize the FID H2 supply to normal pressure typically 25 psig Pressurize the FID Air supply to normal pressure typically 20 psig Ignite the FID flame The FID FLAME temperature will increase allow it to stabilize for
5. 14 0 CH4 120 0 e CO2 12 0 a j j p 100 0 Signal to Noise 10 0 2 N X 80 0 80 Z o 28 25 5 o 60 0 60 a 5e z O 40 0 40 oc N 20 0 2 0 0 0 0 0 15 0 20 0 25 0 30 0 35 0 40 0 45 0 50 0 55 0 60 0 Total H2 Flow to Flame Tip cc min Figure 72 FID Response to Varying He Flow Note that the analyzer is relatively insensitive to H2 flow rate changes between 33 and 43 sccm Detector signal to noise is roughly maximized in the same regime Page 90 Peak Performer 1 Users Manual FID Response With Varying Air Flow H2 40sccm amp Carrier 55 sccm 140 0 14 0 120 0 12 0 g 100 0 10 0 2 lt S 80 0 80 Z o L Q o E 9 60 0 6 0 Sex Bh am e 40 0 hi 40 e CO2 n we a Signal to Noise a 0 0 0 0 100 125 150 175 200 225 250 275 300 325 350 375 400 Total FID Air Flow cc min Figure 73 FID Response to Varying Air Flow Note that the analyzer is relatively insensitive to Air flow rate above 200 sccm and detector signal to noise reaches a stable value above 200 sccm Peak Labs recommends that the analyzer be operated in the flow regions that yield the most stable response and signal to noise characteristics 8 4 Resolving Random Spikes on the FID Baseline There are two primary causes for random baseline spikes appearing on the chromatogram Figure 74 Chromatograms S
6. 45000 Time Figure 57 Typical Chromatographic Detector Signal Showing a Peak Chromatographic peaks in the PP1 are measured by establishment of the normal stable detector signal then determining the added electronic signal that was created by the peak passing through the detector Since the analyzer is monitoring the detector electronic signal over time the added signal is measured in real units such as volt sec By virtue of a conversion factor called the Response Factor the volt sec signal can be directly related to concentration units Page 75 Peak Performer 1 Users Manual PEAK START PEAK END Figure 58 Illustration of Measurement of Chromatographic Peak Area Note The PP1 analyzer supports only area based concentration determinations Determinations based upon peak height as not currently available The first task in quantifying peaks is establishment of the normal stable detector signal baseline This is accomplished by determining the signal departure and return points for the peak event The parameters used when defining detector baseline signal and peaks are Page 76 Analysis Database Name PkCen PkWin PkHat Analysis Averaging 4 pea Figure 59 Typical PP1 Peak Analysis Database Peak Performer 1 Users Manual PkWin Figure 60 Illustration of Chromatographic Peak Parameters Name The peak identification tag expressed as 5 alo
7. Page 23 Peak Performer 1 Users Manual 7 Plug the BYPASS OUT port on the front panel 8 Ensure that the front jumper tube is connected between SAMPLE IN and SAMPLE OUT 9 Package the analyzer in a hard cover carrying case or comparable shipping container If cardboard packaging is used Peak recommends double boxing of the analyzer using at least 2 of resilient packing material between the inner and outer box walls 4 0 Peak Performer Operator Interface SET UP MAIN SCREEN PAGE KEY TREND amp ANALOG OUTPUT SCREEN PAGE KEY CALIBRATION DATABASE SCREEN PAGE KEY ANALYSIS DATABASE U SCREEN PAGE KEY EVENT PROGRAM EDITOR 3 SCREEN PAGE KEY a ee STREAM SELECTOR PROGRAM EDITOR q SCREEN PURCHASED OPTION Z PAGE KEY SS p RUN fanaa nanan eee nnnnnnnnnnnnnnnnnnnnnnnnnnnnn RUN DATA UPPER RionT CHROMATOGR AM MANUAL KEY DISPLAY KEY SCREEN be a OEE da tae cetera es eat Z Meets SCREEN P MANUAL CONTROL DISPLAY CONTROL PAGE KEY SCREEN SCREEN Bee Pt Mt ea dt a at P a A a a p ESC KEY SET UP MAIN SCREEN Figure 10 Software Menu Structure Page 24 Peak Performer 1 Users Manual 4 1 Set up Screen The Set up screen is multi functional Different command buttons appear at the bottom line of the screen dependent upon the section containing the asterick cursor 1 The uppe
8. The PP1 Modbus holding register map defines a set of parameters which are treated as holding registers having addresses 4XXXX According to the Modbus protocol in response to a request for register 4XXXX of a particular slave device the Modbus master reads register XXXX 1from the slave For example Modbus register 40054 corresponds to holding register 53 There are two classes of Modbus registers within the PP1 Modbus Output Registers and External Control Registers See Table 3 below Page 62 Peak Performer 1 Users Manual PP1 Modbus Holding Registers Map Modbus ates 40001 Unit serial number UINT16 40002 Main controller software version UINT16 40003 Detector type RCP FID PDD TCD UINT16 igoa Run Mode ldle Single Cycle UINT 6 Stream 40014 40039 _ Spare SSS o o o o peace 1 Concentration 40048 40049 40050 Compound 2 Name _ 40054 Compound 2 Area Counts UINT32 Compound 2 Concentration 40058 40059 40060 Compound 3 Name _ 40064 Compound 3 Area Counts UINT32 Compound 3 Concentration 40068 40069 Seare oS o o o o 40070 Compound 4 Name 8CharStrino 40074 Compound 4 Area Counts UINT32 Compound 4 Concentration 40078 40079 S eare ooo o o UNN o SS 40080 Compound 5 Name 8CharStrino 40084 Compound 5 Area Counts UINT32 Compound 5 Concentration 40088 40089 Seare oS o o o oo 40090 Compound 6 Name 8CharStrino 40092 Compound 6 Area Counts UINT32 Compound 6 Concentration
9. steel tubing COM Ka D e SAMPLE 1 SAMPLE 1 ACTUATOR CARRIER FID FID T N IN AIR H2 COM2 TO FROM OUT TRAP TRAP 1 F a pe 7 START FLM SW r a Ca GNL ALM F Jeak Performer Gas Analyzer 2 si Mode PP1 SM j FID Application 920 220 CH4 amp CO2 amp NMHC in 02 Samples 200 240 VAC 50 60 Hz 160 WATTS C COMPLIANT MADE IN THE USA Serial Number 649 650 691 1267 ff Figure 5 Rear View of PP1 FID Page 11 Peak Performer 1 Users Manual 120 VAC Oxygen Nitrogen Argon Helium a Hydrogen dio Samples a CDA DA COMBUSTION 4 FUEL Figure 6 FID PP1 Gas Supply Schematic 2 5 1 Carrier Gas Supply The instrument will accept a variety of carrier gases No Ar or He See Section 2 5 1 1 y a CAUTION Oxygen is never a suitable carrier or actuator supply gas Oxygen is highly reactive and many pneumatic components contain greases and oils that combust spontaneously when exposed to oxygen Consult the test data shipped with the analyzer in CD format for carrier gas details specific for your analyzer Commonly the PP1 will utilize highly purified nitrogen as the carrier gas supply and nitrogen is considered the best multi purpose carrier gas However the best carrier to use approximates the sample matrix i e nitrogen carrier for analysis of impurities in nitrogen Matching the carrier gas to the sample will prevent upsets caused by the elution of high conce
10. CALIBRATION DATABASE SCREEN As the concentration peak area is determined the analyzer applies the pre programmed response factor as an inverse proportional factor to generate the reported concentration value PEAK CONCENTRATION PEAK AREA RESPONSE RESPONSE FACTOR Page 34 Peak Performer 1 Users Manual 4 3 2 1 Establishing New Instrument Response Factors Connect a known calibration standard gas span gas to the analyzer at the SAMPLE IN port on the front panel If soan gas connection is made at the rear panel SAMPLE IN port ensure that the front jumper is connected between SAMPLE OUT and SAMPLE IN on the front panel Verify that sample is flowing freely through loop exit flow from the SAMPLE OUT should be 30 to 120 cc min Press the ESC or PAGE keys as needed to navigate to the RUN screen Press the SINGLE CYCLE RERUN key to toggle to SINGLE mode Press the RUN key to initiate analysis the P1 event program will be loaded automatically and executed Allow the analyzer to fully execute the event program Current concentration data will be displayed as an overlay on the RUN screen as peaks are identified and quantified Press the PAGE key as needed to toggle to the CALIBRATION DATA BASE screen Place the at the first compound of interest and press the EDIT key use the up down left and right arrow keys to enter the span gas concentration in the CONC field Be certain to use the right arrow key to fully exi
11. channel to be configured to 9600 bps 7 data bits even parity and one stop bit 6 4 2 Modbus Packet Structure Every Modbus packet consists of four fields e Slave Address Field e Function Field e Data Field e Error Check Field LRC Checksum Slave Address Field The slave address field of a Modbus packet is one byte two ASCII characters in length and uniquely identifies the slave device involved in the transaction Valid addresses will be in a range between 1 and 247 A slave device performs the command specified in the packet when it receives a request packet with the slave address field matching its own address A response packet generated by the slave has the same value in the slave address field Function Field The function field of a Modbus request packet is one byte in length and tells the addressed slave which function to perform Similarly the function field of a response packet tells the master what function the addressed slave has just performed On page 61 lists the Modbus functions supported by the PP1 when acting as slave please refer to Table 2 Modbus Functions Supported by the PP1 as Slave Page 57 Peak Performer 1 Users Manual Data Field The data field of a Modbus request is variable length and depends on the function This field contains information required by the slave device to perform the command specified in a request packet or data being passed back by the slave device in a response packet Dat
12. contribution due to the peak passing through the detector can then be quantified by area calculation using time slices and signal differentials above the newly established baseline Page 82 Peak Performer 1 Users Manual PEAK START PEAK END Figure 67 Peak Area Calculation The formula for peak area calculation can be expressed as Peak Area 12 x Hgt Hgtz x t1 2 x Hgte Hgts x te 2 x Hgts Hgta x ts where Hgt the signal differential between the instantaneous baseline level and the peak signal value tx the time difference between data points Using a constant value for tx the peak area calculation simplifies to Peak Area tx xX Hgt Hgte Hgts Hgt Peaks quantified using the Variable method are denoted with a V in the last column of the data report Page 83 Peak Performer 1 Users Manual 7 7 Chromatographic Stabilization of the Analyzer When Injecting O2 Samples O2 samples present particular challenges for the FID PP1 analyzer due to the extreme reactivity of 100 O2 with any possible carbon source even at relatively low temperatures via these basic reactions 2C O2 gt 2CO C O gt gt CO Potential carbon sources include residual carbon within stainless steel tubing and valve bodies polymeric valve components and column packing materials CO and COz2 produced from these sources can be detected in the FID and create a wide variety o
13. example with consecutive runs The run of concentration data at 16 33 is displayed in RED to denote that there was a general error in the PP1 during this run By Viewer 2014 02 05 File Start Stop Chrom View Run Time Stream CO 15 46 1 15 53 1 15 59 1 16 06 1 16 13 1 16 19 1 16 26 1 16 33 1 16 39 1 16 46 1 6957 0 6965 9 6973 5 5978 4 6978 0 6980 5 6986 1 6998 5 0 0 0 0 Event CH4 4744 5 4797 1 4794 0 4793 2 4794 4794 6 4301 3 4303 3 0 0 0 0 Info CO 5260 1 5276 7 5286 6 5286 7 5290 2 5270 5 5291 1 5292 2 17 1 17 3 NMHC 10616 3 10264 7 10621 8 105828 8 10303 0 10631 5 10639 4 10620 53 0 0 1 8 Figure 35 Viewer screen showing concentration data There are eleven individual error conditions that can cause the Viewer Line to appear red e Detector Communication Error e Temperature Zone Out of Range Temperature Zone Disabled Detector Zeroing Target Error e e Vlamp Low Voltage Out of Range e FID Flame Temperature Out of Range e Event Program Load Error e Stream Selector Program Error e System Parameters Corrupted e Parameter Change Update Needed e Detector Power Page 48 Peak Performer 1 Users Manual 5 5 1 2 Viewer Line Details Window This window is displayed by double clicking on any time stamp on the Viewer window The screen provides detailed analytical information about the run selected Left Width sec Rowan seo 8 Measured Area 474
14. in order for receive the COM2 port output data The protocol to request data from the PP1 consists of 1 A start of transmission character 2 Followed by the unit serial number 3 An end of transmission character or STX character 02 hex SSSS ETX character 03 hex The requesting command format follows lt STX gt SSSS lt ETX gt where SSSS serial number of unit is used as the RS 485 ID 6 3 2 COM 2 Port PLC Output Format The COM 2 port output format consists of unit serial number date and time stamp error alarm stream number followed by impurity data This data format is transmitted at the end of every run automatically if the COM 2 mode is set to Auto This format uses a general protocol envelope This envelope consists of a start of transmission character followed by data and end of transmission character The start of transmission indicator is a STX character 02 hex and the end of transmission indicator is a ETX character 03 hex The fields within each record are defined as follows lt STX gt SSS YYYY MM DD HH MM SS E X N AREA CONC N AREA CONC N AREA CONC lt ETX gt SSS Serial Number of Unit This is also used as the RS 485 unit ID YYYY MM DD Date 2013 12 05 HH MM SS Time 12 23 44 12 hours 23 minutes 44 seconds E General Error Alarm 0 No Error 1 Error X Stream Number N Name of Impurity x6 AREA Are of Impurity x6 CONC Concentration of Impurity x6 Page 56
15. is via 9 pin straight through cable connection to COM 1 and COM 2 e Analog outputs are available from the DIN screw terminal strips on the rear panel e The FID drain line must be 1 inside diameter minimum and without restrictions its entire length 2 3 Electrical Connections Verify the correct operating voltage as marked on the rear of the analyzer at the main power switch Attach a standard power cable to the rear of the instrument See Figure 1 and connect to an appropriately grounded outlet Power Cord PP1 Power Entry Figure 1 AC Power Connection Details Page 8 Peak Performer 1 Users Manual The PP1 has been CE certified to be immune to AC frequency and voltage variances of 10 of the nominal AC operating voltage Refer to the final test report and or markings on the rear of analyzers to verify the proper operating voltage for each unit For best stability power to the analyzer should originate from an electrical circuit free of large inductive or other current loads Be sure to mount the analyzer in an area of adequate ventilation and make sure the cooling fan inlet is unobstructed There are no battery back ups or reserve power supplies built into the PP1 therefore any disruption of the AC supply will result in restarting of the analyzer Peak Labs recommends the installation of a high quality on line or double conversion type of uninterruptible power supply UPS Be sure to mount the analyzer in an area
16. sccm CH4 RT 93 sec CH4 RT 97 sec CH4 RT 102 sec gt a td el PPP pp pb 100 120 140 160 180 200 220 240 Figure 53 Peak Shifting as a Result of Improper Vent Needle Valve Flow Comparison of retention times for un vented versus vented chromatograms will reveal improper adjustment of the vent flow control needle valve Careful adjustment of the vent needle valve will enable the operator to minimize peak retention drift and create a consistent chromatogram 7 5 Effects of Temperature and Flow on Analytical Columns The normal chromatogram can be affected by changes in column flow and temperature Be aware that changes of operating parameters from final test conditions can require parametric adjustments i e peak detection parameters response factors valve timing within the analyzer Page 72 Peak Performer 1 Users Manual Name Conc Area R Time R Factor A Type Hz 4270 35 1341021 45 58 3191 V CO S47 5 4616126 106 8 13283 V 16 5 Uni 1S 81 MS13X SPEAK Column Temperature 105 C Carrier Flow 20 5 mifmin N2 OFFSET e ATTEN ize SPAN z i i Figure 54 Standard chromatogram The normal PP1 chromatogram Figure 55 is affected by changes in column temperature as illustrated in comparison with the chromatogram of Figure 56 In the circumstance of column temperature change an increase of 30C has shifted t
17. the ignition probe for 20 seconds Bias Toggles the negative accelerating voltage within the FID to ON BIAS or OFF V1 Toggles Valve 1 between CW and CCW positions V2 Toggles Valve 2 between CW and CCW positions Esc Exits from the Manual sub screen to the Run screen 4 7 4 Display Screen Sub Screen of the Run Screen The Display sub screen allows the operator to adjust the horizontal scale vertical scale and baseline offset of the chromatogram These functions mimic those of a standard chart recorder Single lt U0ff 188 Hatt UOFt Attn Attn Sean Ese Figure 30 Run Display screen 4 7 4 1 Display Screen Button Functions VOff Scrolls the screen up maximum Voff 11 without changing the scale VOff scrolls the screen down minimum Voff 0 without changing the scale Atin Toggles the attenuation vertical scaling max Attn 11 up Attn Toggles the attenuation vertical scaling min Attn 1 down Span Toggles the window view horizontal scaling in seconds Esc Exits from the Display sub screen to the Run screen Page 43 Peak Performer 1 Users Manual 5 0 Peak View Software The Peak View software has two main capabilities Primary functions concern acquisition and archiving of compound concentration and acquisition and collection of the chromatogram data The software also provides the ability to display and print the data from a remote computer platform Peak Vi
18. will begin flow of purified gas through the sample loop 2 Wait 10 minutes to purge the analyzer completely of any residual gas samples 3 Initiate a standard sampling run in CYCLE mode 4 Collect 5 sample runs with Peak Viewer 5 Average the concentration data of the 5 runs for each peak of interest 6 Average readings higher than 1 ppb for any compound indicates a loss of valve seal integrity and possibly suggests valve head replacement is necessary Page 97 Peak Performer 1 Users Manual 9 4 Start up Sequence for Replacement Methanizer 1 Allow the methanizer heater zone to cool to 60 C Turn off power to analyzer Unplug the AC power cord Turn off the FID H2 and FID Air supplies to the analyzer Leave carrier gas flowing at normal pressures Remove the PP1 top cover Locate the FID Module in the rear of the PP chassis a SF Ve a lt lt gt k TTEN CS a i d z is R m E Figure 77 FID Module 6 Remove the FID oven Cover Figure 78 FID Module with cover removed Page 98 Peak Performer 1 Users Manual 7 Remove the methanizer insulation and stuffing from the front of the methanizer heater block Figure 79 FID Module with insulation removed 8 Use a 2 Phillips screwdriver to remove the methanizer cover retaining screw Remove the cover and expose the methanizer Figure 80 Removing the retaining screw Page 99 Peak Performer 1 Users Manual
19. 30 ID for 3 16 cc to 1 2 cc loops 0 020 ID for 50 uL to 1 4 cc loops Note the shortest practical length of tubing for a sample loop is about 8 inches Note Do not use tubing less than 0 016 ID as it acts like a flow restrictor instead of a sample loop 3 The correct length for the loop tubing is calculated as follows Internal volume V in cc s 3 142 x ID 2 in inches x L in inches x 16 38 4 re arranging L in inches 0 777 x V in cc s ID 2 in inches an example for a 1 cc loop L inches 0 777 x 1cc 0 040 2 49 inches tube length 4 Measure to length cut and install VICI fittings 5 Blow the tube out with compressed air to remove any particles Page 103 Peak Performer 1 Users Manual 9 7 Testing the Heater Resistance MINMAX RANGE Figure 83 Heater Resistance for 90 120 VAC AC Service 177 AUS AAS AA TaT Figure 84 Heater Resistance for 200 240 VAC AC Service Page 104 Peak Performer 1 Users Manual 9 8 Main DC Power Supply Replacement Main DC Power Supply Replacement Purpose Replace upgrade Phihong PSA4531 DC Supply with Power One MAP40 300 DC Power Supply Procedure Power off analyzer if gas umbilical tubing is used it is not necessary to cool down the analyzer Maintain normal gas supplies Disconnect AC power cord Remove top cover Locate the main DC power supply in the right rear portion of the chassis see Figure 1 5 r A if 4 M
20. 4 to 12 hours After the stabilization period lower Methanizer heater zone temperature to 295 C Allow the Methanizer heater zone temperature to stabilize at 295 C for at least 15 minutes before running samples NOTE Full re calibration is recommended after methanizer replacement Refer to Section 3 6 Page 101 Peak Performer 1 Users Manual FERC cake siditienteceetie aF LE ae Sere ee ee es a a a C Coa a a a a iF a rid g m 5 oe oe 3 RER RR PERAE R 3 a rae ee eee er a e k ji Cm DO a tA ons i i ls riike a es T i F LELET T ET RA TELT r ee ee p T emmeliue Adjust this potentiometer to change display instensity and contrast Figure 82a View of the MCPU Showing the LCD Contrast Potentiometer MCPU adjustments for software versions 1 3 Adjust this potentiometer to change display instensity and contrast Figure 82b View of the MCPU Showing the LCD Contrast Potentiometer MCPU adjustments for software versions 4 and above Page 102 Peak Performer 1 Users Manual 9 6 ALTERING THE ANALYTICAL RANGE OF THE INSTRUMENT Sample loops are very easy to customize 1 Determine the desired loop volume Analytical range is directly proportional to sample loop size 2 Select tubing tube internal diameter to use In general use the largest ID tube possible to avoid flow restrictions Guidelines 0 040 ID for 3 8 cc to 2 cc loops 0 0
21. 40098 40099 Spare S oo d o Table 3 Modbus Holding Registers Supported by the PP1 Page 63 Peak Performer 1 Users Manual 6 5 Trend Analog Outputs There are seven independent analog outputs on the back of the PP1 The first six are tied to the six impurities as trend outputs and the last channel is a simple recorder output These trend outputs are provided via 0 1 0 VDC screw terminals Each impurity can be independently scaled by entering the desired range e g 0 gt 1000 0 to 1000 ppb 0 1 VDC scale At the end of each run the analog trend signal is updated and holds until the end of the next run is completed As an accessory Peak can provide standard commercial VDC to mA converters as needed 6 6 Setting up a RS485 Network The RS 485 specification supports two wire half duplex communications only one unit may transmit at a time but allows up to 32 users on a party line network NOTE The RS 422 specification supports four wire full duplex communications two units may transmit at a time and also allows up to 32 users on a party line network The following information is provided to enable the users to install the Peak Performer 1 intoa RS 485 network This system diagram consists of the PP1 RS 232 to RS 485 converter and master host controller pd COM2_ f RS232 to RS485 RX Converter P g Io Master Controller ee TX COM2 RS232 to RS485 PP1 Converter P OWE h aen Power Supply
22. 6041 Factor oo Wah Ara Flame Temperature Run Type System Alarm Analysis Index Figure 36 Viewer Detail screen showing raw analysis data The information on the screen is linked to run 16 33 displayed in figure 35 5 5 2 Start Menu on the Viewer Taskbar Single Run Cycle Run Stream Run Figure 37 Start menu on the taskbar Page 49 Peak Performer 1 Users Manual The Start menu contains the following commands ee Single Run selection commands the PP1 to start a Single Run Cycle Run Cycle Run option commands the PP1 to start a continuous Cycle Run stream Run selection commands the PP1 to start a Stream Selection Run This operation only function if the Stream Selection option is installed 5 5 3 Stop Command on the Viewer Taskbar The Stop Command selection instantly sends a command the PP1 to terminate the current run immediately 5 5 4 Chrom View Menu and Chromatograph Viewer Window The Chrom View menu selection opens the Chromatograph Viewer window Two methods can open the Chrom Viewer window 1 The first method is to select the Chrom View menu selection from the Viewer taskbar and then select a chm file to display 2 The second method of opening the Chrom Viewer is double clicking one of the concentration values displayed in the Viewer window Using either method after the chromatogram data is loaded the display can be adjusted by the Offset Attenuation and Span scroll bars ze
23. 8 chm Viewer Analysis DB Open SUN 256 SRAN 400 Cons Poly n d po qd P Co D L Chromo Print L Offset Exit R Offse Peak Bi Peak Area co2 NMHC Peak Cons Fact Flame Temp 145 5 Analysis Type Figure 39 Baseline Selected Page 51 Peak Performer 1 Users Manual z Chrom Viewer 2014 02 05 1528 chm Viewer Analysis DB Open 2 2 SPAN 400 Cons Poly d iH d H Save s D L Chromo d BaseLine m Print j L Offset Exit R Offset Peak Height Peak Area Peak Cons Resp Fact Flame Temp 145 5 Analysis Type Figure 40 Baseline Deselected The File menu offers the following commands Fonon Dente open Opens a chromatogram file Use this command to open and load the chromatogram data for display Save the chromatogram data that is currently displayed Enables display of compound name and integration baseline information em a 5 5 4 3 Viewer Menu on the Chrom Viewer Taskbar The Viewer menu selection returns the user to the original Viewer window See Figure 36 Page 52 Peak Performer 1 Users Manual 6 0 Communication Port Protocol and Formats There are two serial communications ports on the rear of the PP1 COM1 isa multifunctional serial port COM2 port is a dedicated PLC output port 6 1 COM1 COM2 Port and Cable Wiring The cable connected from the PC to the PP1 should be a straight through wired 9 pin M
24. C Slave Modbus a Register As you can see from the response packet above the response is the echo of the requested packet 6 4 4 Modbus Data Format The PP1 is capable of exporting all holding registers into the Modbus protocol The PP1 data available in a contiguous set of Modbus holding registers The PP1 output registers are located in the Modbus register map from 40001 to 40099 The actual location is defined in table 3 below Six Data Formats Used in the PP1 Analyzer UINT16 16 bit unsigned integer 0 to 65 535 INT 16 16 bit signed integer 32 768 to 32 767 UINT32 32 bit unsigned integer 0 to 4 294 967 295 INT32 32 bit signed integer 2 147 483 648 to 2 147 483 647 Boolean Packed Boolean Format 8CharString 8 character string format 16 bit Integer Format Unsigned and signed 16 bit integer formats are the simplest formats Each PP1 address corresponds to one Modbus Holding Register If the format is unsigned the value range for the output registers is 0 to 65535 If the format is signed the value range is 32767 to 32767 32 bit Integer Format To accommodate values that can reach beyond the 16 bit range the Modbus Slave provides 32 bit integer format as an output option In signed and unsigned 32 bit integer formats each PP1 address corresponds to two 16 bit Modbus Holding Registers A 32 bit register represented in 32 bit integer format is passed via communications as two 16 bit registe
25. COM2 Port and Cable Wiring Viewer Software Window File Menu on the Viewer Taskbar Communication Setting Window Viewer Line Details Window Start Menu on the Viewer Taskbar Stop Command on the Viewer Taskbar Chrom View Window and Chromatogram Viewer Window Chromatogram Files File Menu on the Chrom Viewer Taskbar Viewer Menu on the Chrom Viewer Taskbar Communication Port Protocols and Data Formats COM1 COM2 Port and Cable Wiring Port 1 Protocol COM 1 Port Settings Peak View Output Columns format in CSV file Detector Output External Start Command String Detector Signal Data String Port 2 Protocol COM 2 Settings COM 2 Port PLC Output Format Modbus Protocol and Register Map for Peak Devices Mode of Transmission Modbus Packet Structure Packet Communications Peak Performer 1 Users Manual 6 4 4 Modbus Data Format 60 6 4 5 Broadcast Packets 61 6 5 Trend Analog Outputs 64 6 6 Setting up a RS485 Network 64 6 6 1 RS232 to RS485 Converters 64 7 0 Chromatographic Principles 65 TA Sample Injection 65 7 2 Carrier Gas Purification 65 7 3 Component Separation 66 7 4 Venting and Flow Balancing 69 7 9 Effects of Temperature and Flow on Analytical Columns 72 7 6 Peak Identification and Quantification ihe 7 6 1 Peak Quantification Fixed Mode 79 7 6 2 Peak Quantification Forced Baseline Mode 79 7 6 3 Peak Quantification Variable Mode 80 7 1 Chromatographic Stabilization of the Analyzer When Injecting 84 O2 Samples 8 0 Fla
26. Chrom Viewer 2014 02 05 1528 chm Viewer Analysis DB Open SaveAs D L Chromo gt BaseLine Print R Offsel Peak Height Peak Area Peak Cons Resp Fact Flame Temp 145 5 Analysis Type Figure 38 Chromatogram Viewer Window Page 50 Peak Performer 1 Users Manual NOTE Viewer window scaling does not match the analyzer s display scaling A higher degree of resolution is available in the Viewer window For instance Viewer ATTN 8 approximately is equivalent to analyzer display ATTN 1 5 5 4 1 Chromatogram Files Chromatograms are archived on the host computer as text files suffixed chm The text files can be imported into most common laboratory analysis soreadsheet and word processor programs as needed Data points in the chromatogram file are time sequenced at 0 2 seconds per data point The filename of the chromatogram file is generated by time of day on the host computer and the file is stored in a folder that corresponds to the date of collection A corresponding Viewer data file is created and or updated at the time the chromatogram file is created As an example the fourth chromatogram shown in Figure 36 would be archived on the host computer as follows Main directory C Viewer Sub directory 2013 12 05 YYYY MM DD of archive creation Viewer filename 2013 12 05 csv Filename 0851 chm 5 5 4 2 File Menu on the Chrom Viewer Taskbar i i Chrom Viewer 2014 02 05 152
27. Concentration lt 10 ppm CO Concentration lt 10 ppm CO Concentration lt 10 ppm H2O Concentration lt 100 ppm CAUTION High moisture content in the FID H gas supply has been shown to irreversibly damage the methanizers ruthenium catalyst Page 15 Peak Performer 1 Users Manual 2 5 2 1 FID H Gas Generators Peak recommends only the use of Palladium Transfer Tube or Regenerative Drying Hydrogen Generators Hydrogen produced by electrolytic decomposition of water is extremely humid at nearly 100 relative humidity H generators using only single stage gas H2 dryers molecular sieves will saturate with moisture within a week or two of normal use and therefore require frequent manual exchange and regeneration to maintain acceptable H gas quality 2 5 2 2 FID H2 Gas Cylinders Cylinder sources suitable for use as FID H2 include UHP and Zero Quality grades Nominal UHP Grade lt 10 ppb THC 2 5 3 FID Zero Air Gas Supply Oxygen bearing gas must be supplied to the Flame lonization Detector for combustion support The PP1 FID Air gas connection utilizes a 1 16 female VICI bulkhead labeled FID AIR on the rear panel FID Zero Air Gas Specifications High Pressure Cylinder or Zero Air Generator Gas Type 79 N gt 2 21 O2 Maximum Flow rate lt 500 cc min THC Concentration lt 10 ppm CO Concentration lt 10 ppm CO Concentration lt 1000 ppm H2 H2
28. ECORDER REMOTE START FID FLAME GEN ALARM Figure 19 Analog Output Connections 0000000000 COMMON GND COMMON GND COMMON GND COMMON GND COMMON GND COMMON GND COMMON GND COMMON GND FID FLAME GEN ALARM NOTE The analog outputs are locked if the Port 1 Protocol on the MAIN SCREEN is set to DETECTOR See Section 6 2 Peak Performer 1 Users Manual 4 2 3 Analog Interface Wiring Breakdown There are 10 total terminal connectors from the top the connectors ID s are Terminals 1 6 e Impurity Trends All channels are mapped to the calibration database All channels are 0 1 VDC All channels signals are updated at the end of run and held All channels are manually scalable on the ANALOG INTERFACE SCREEN e g 0 gt 1000 0 to 1000 ppb 0 1 VDC scale Maximum scale is 999 999 Optional converters to provide other current voltage outputs are available Please contact your local Peak representative for additional information Terminal 7 e Analog recorder raw signal 0 1 VDC range Terminal 8 e Remote Start Input The remote start input is activated by shorting the terminal 8 to COMMON GND for at least 100ms The remote start input must then return to an open state unshorten Terminal 9 e FID Flame Switch Relay The FID Flame and General Alarm switch relays are SPST N O and rated for 0 5 amps 200VDC 10VA Terminal 10 e General Alar
29. ERNAL EXTERNAL HETTER PURFER FA D REAA PANEL TO PLET ADE WARIO Ai TO FO DETECTOR Ra IVPASS OUT amp FRONT PANEL See i yi vk Fa ANFLE OUT REAR PANEL INTERRAL ETERNAL SAMPLE ill chlen SAMPLE CLT FRONT PANEL VALVE 1 SAMPLE IN REAA PANEL ilies i aaa i NTERNAL EXTERMAL Figure 43 Typical FID plumbing diagram Immediately after injection the entire contents of the sample loop are moved to the head of the column s and component separation begins Figure 44 Peak Development on the Analytical Column Soon After Injection Page 67 Peak Performer 1 Users Manual E EETA o eee Figure 45 Peak Development Midway on the Analytical Column EREN SE Bae BR riii Figure 46 Peak Development Midway on the Analytical Column Analytes of interest can be allowed to continue on to the detector as long as desired In some cases the resulting chromatogram can become quite long in duration In other circumstances it is not necessary to quantify all possible peaks and the remaining balance of the sample is back flushed to vent or detector Page 68 Peak Performer 1 Users Manual DUS Roo OAA AAAA 1 fy BORER SSeS AOA aeres I Sesseseaseeqtecsestensesessees 1 PCy Ho th Mira imh L I Figure 47 Peak Development on the Analytical Column After Backflush LI A G 2 O JA ee T E ETA N a a E EF E EA T r ro ARE
30. Electrometer Housing NS Gas Vent amp Drain Vent Cap ja _ Tower Collector Probe CT S Flame Out Sensor ree D See a Insulator ae TTA K E e LO r x Flame Tip Base Column r Hydrogen Figure 69 Standard FID Section Page 88 Peak Performer 1 Users Manual Normal life of the methanizer is approximately 84 months under continuous use Replace and dispose of properly in accordance with local and federal regulations 8 2 Temperature Effects Within The Methanizer and FID Tower The FID Tower is heated indirectly by the methanizer block to roughly 95 C to minimize moisture condensation It is critical to allow the FID Tower to heat thoroughly before igniting the flame Failure to do so may trap moisture within the FID Tower and compromise the ceramic insulators Between the temperatures of 250 C and 325 C this reaction on the surface of the Ruthenium Oxide catalyst can proceed CO 4H2 gt CH 2H20 and CO 3H2 gt CH H2O The rate and completion of these reactions is dependent upon temperature and residence time It is critical to note that the catalyst reaction can halted by the presence of moisture in the gas stream particularly if the hydrogen for methanization has high moisture content Above 360 C CO thermally decomposes on the catalyst surface and methanization is not possible A The Peak Lab FID methanizer has been optimized for methanization of CO2 s
31. F cable attached to the PC s COM port and the PP1 s COM port PC MALE PP 1 FEMALE 9 Pin Cable from PC to PP 1 Figure 41 COM Cable Wiring Peak Labs recommends limiting cable lengths to 25 feet maximum 6 2 Port 1 Protocol There are two COM1 output formats Peak View and Detector Proper selection of protocol is determined by the application in use on the host computer 6 2 1 COM 1 Port Settings The RS 232 settings for COM 1 port are 38400 baud rate 8 bit data 1 stop bit and no parity These settings are fixed and are not user selectable Page 53 Peak Performer 1 Users Manual 6 2 2 Peak View Output Columns Format in CSV file The Peak View software stores information in a common text format Comma Separated Variable CSV CSV files can be opened in common spreadsheet applications for further analysis The column format in the CSV files are A Data Time B Run Mode C Analysis Buffer Number and Stream Number D General Error Alarm E RCP Lamp Voltage or FID Flame Temperature NOTE No values to be measured for TCD or PDD and will show up as 0 F Compound Name G Retention Time H Left Point Offset Right Point Offset J Area K Response Factor L Processing Flag V F or B Columns F to L are repeated for M to S T to Z and AA to AG for the next five compounds listed in the Calibration Data Base 6 2 3 Detector Output The detector output format of the COM1 interface curren
32. LIBRATION DATA BASE screen Place the at the first compound of interest and press the EDIT key use the up down left and right arrow keys to enter the span gas concentration in the CONC field Be certain to use the right arrow key to fully exit the CONC field or all updates will be lost With the before the compound name press the UPDATE key The analyzer will recalculate the appropriate response factor for the compound based upon the span gas concentration and analyzer area response using the following formula RESPONSE FACTOR AREA RESPONSE SPAN GAS CONCENTRATION NOTE The LED on the analyzer s front panel will change from green to red to remind the user that the current calibration information is stored in volatile temporary memory only and will need to be saved to permanent memory at a later time Repeat the sequence for each of the compounds shown on the CALIBRATION DATA BASE screen Repeat analysis of the span gas sample and verify that the analyzer reports data values within normal calibration tolerances i e 5 3 7 Shutdown and Transport Shut off H2 supply Allow the temperature zones to cool below 50 C approximately 2 hours Allow carrier to flow during cool down time Shut off carrier after cool down time and plug the CARRIER IN FID H2 FID AIR ports on the rear of the analyzer Power off analyzer 6 Cap the SAMPLE IN SAMPLE OUT and ACTUATOR IN ports e O N O1
33. O Concentration lt 100 ppm Page 16 Peak Performer 1 Users Manual Synthetic air sources suitable for use as FID Air include Zero and Breathing Quality grades CAUTION Compressed room air is not recommended 1 Connect the Zero Air gas supply to the bulkhead and set the source regulator to approximately 20 psig 2 There are no internal regulators in the standard FID PP1 all gas pressures are controlled by external regulators customer supplied 2 5 4 Actuator Gas Supply The actuator supply is attached at the rear panel of the instrument Attach the air or inert gas actuator supply to ACTUATOR IN port on the rear panel Preset the source to 60 80 psig Nominal Clean Dry Air lt 10 ppm l 2 5 5 Sample Gas Supply Sample lines are normally attached to the rear panel of the instrument Attach sample or span gas lines to the SAMPLE IN port on the rear panel The SAMPLE OUT port must be unrestricted Sample gas must be supplied to the analyzer at low pressure 0 3 to 1 0 psig and moderate flow 30 to 120 ml min The analyzer does not have any sample gas pressure flow regulation equipment Higher sample pressures can be used if a fixed restrictor is set and calibrated to the incoming pressure Please contact the factory for sample handling instructions if these input conditions are not available SAMPLE GAS SUPPLY OO TOPP a 9 a TL FLOW RESTRICTOR 30 60 seem ATMOSPHERIC
34. PRESSURE Figure 7 Sample Supply Flow Schematic Page 17 Peak Performer 1 Users Manual 2 5 5 1 External Calibration Gas Supply Certified calibration standards must be connected periodically to the PP1 for verification of analyzer response When using a mobile calibration gas source such as high pressure cylinder the plumbing arrangement shown in figure 7 is recommended The calibration source can be connected to the SAMPLE IN port on the analyzer front panel or alternatively make sure the front panel jumper between SAMPLE OUT and SAMPLE IN is installed and connect the calibration source to the rear panel SAMPLE IN port The SAMPLE OUT port must be unrestricted when using either method 2 5 5 2 Second Sample Gas Supply Peak Labs offers an optional second sample inlet stream for most analyzers Connection to the SAMPLE 1 IN and SAMPLE 2 IN ports should replicate Figure 7 Sample lines are normally attached to the rear panel of the instrument Attach sample or span gas lines to the SAMPLE IN ports on the rear panel The SAMPLE OUT ports must be unrestricted 2 5 6 Calibration Gas Connection for Analyzers Equipped with the Optional Internal Span Gas Blender Peak Labs offers an optional internal span gas blender for most analyzers Connection to the SPAN GAS IN port should replicate Figure 8 Nominal inlet soan gas pressure is 50 psig and flow through the internal blender is preset within the analyzer External restrictors are not require
35. Peak Performer 1 Users Manual NOTE The least significant decimal of the concentration resolution represents 0 1 ppb CONC reading of 1 represents a 0 1 ppb concentration level 6 4 Modbus Protocol and Register Map for Peak Laboratories Devices This section describes the Modbus protocol for Peak Laboratories PP1 analyzer It is assumed that the reader is familiar with the Modbus protocol and serial communications in general The following rules define the protocol for information transfer between a Modbus MASTER device and the Modbus SLAVE The MASTER initiates and controls all information transfer on the communications channel A SLAVE device never initiates a communications sequence All communications activity occurs in the form of PACKETS A packet is a serial string of 7 bit ASCII bytes All PACKETS transmitted by the MASTER are REQUESTS All PACKETS transmitted by a SLAVE device are RESPONSES At most one SLAVE can respond to a single request from a MASTER The PP1 does not support broadcast request packets The PP1 shall only support the ASCII mode Modbus protocol The PP1 is only a SLAVE device The PP1 does not conform to all stated requirements according to the MODBUS Application Protocol Specification v1 1b3 and MODBUS over Serial Line Specification and Implementation Guide V1 02 6 4 1 Mode of Transmission The PP1 only supports the ASCII mode Modbus protocol The PP1 analyzer requires the serial communications
36. Peak Performer 1 Users Manual Peak Performer 1 FID 920 Series User Manual Peak Laboratories LLC www peaklaboratories com 650 691 1267 Version 5 1 6 18 14 Page 1 Peak Performer 1 Users Manual Forward This manual is a reference guide for the operation of the Peak Performer 1 series of gas analyzers The Peak Performer 1 should only be operated by trained personnel familiar with the safe operating procedures of the analyzer The following cautions should always be considered High voltages are required for proper detector operation and are present when the unit is energized chromatographic operation Hot surfaces may be present when the unit is energized Illustrations and photographs contained herein are for example only Actual configurations may vary depending on specific application and installed options Improper installation operation or service of the analyzer can cause permanent damage to the instrument The analyzer is designed to be operated with all covers installed connected to a properly grounded 3 conductor AC line source AN High operating temperatures are required for proper detector and In event of fire Class A B or C fire extinguishers can be used The Peak Performer 1 must have standard electrical power and applicable gas supply pressures as noted on the test documentation for proper operation Permanent damage and voiding of the warranty may result Operators should not attempt t
37. Single Computer For Using Viewer Software Installation of Multiple Analyzers via USB 1 Connect DB9M to DBYF extension cables to analyzers 2 Power up analyzers do not heat Page 109 Peak Performer 1 Users Manual Set Port 1 Protocol on the analyzers to Viewer 4 Insert 4 port USB hub into computer USB port your computer should detect the connection and automatically install any required Windows drivers for USB hubs Connect the USB to DB9 adapters to the DB9 extension cables 6 Insert first USB to DB9 adapter into 4 port USB hub your computer should detect the connection and launch the hardware installation program 7 Insert USB to DBY adapter INSTALL CD in CD drive it will launch automatically if autoplay in enabled on your computer 8 Follow installation instructions that come with USB to DB9 adapter I confirm that it is okay to click the Continue anyway box 9 Your computer may prompt to install the USB to DBY adapter a second time do not cancel it is best to let the computer re install the software again 10 Create a new Desktop folder for each analyzer that you will connect with a USB to DB9 adapter Be sure to give the folders a name that relates to the analyzer that you will connect to that adapter 11 Copy the Viewer exe files into each new folder Open one of the new folders and select the Viewer exe file 12 Double click to launch a Viewer window 13 Go to Windows Device Manag
38. Slave Address 92 5C Hex Modbus Function 03 03 Hex Starting Register 12 000C Hex Num of Register 02 0002 Hex LRC Checksum 109 93 Hex 39 33 ASCII Request Packet non shaded background denotes the DATA field of the packet Starting Register Num of Registers 40013 2 Response Packet Slave Modbus Byte Register 1 Register2 check Address Function Count Address 12 Address 13 The Master device receives the above data packet in response to the request packet Modbus Register 40013 4E38 Hex 20024 Modbus Register 40014 2A60 Hex 10848 Function 06 Preset Single Register Preset a value into a single holding register Place specific values into a single holding registers in the PP1 There is only one holding register that can be written to the PP1 See PP1 register map below Preset Single Register Packet Example In the next example the PP1 s Modbus slave address is 143 and the master requests to write the value of 3 to Modbus register 40004 In accordance with the Modbus protocol register 40004 is numbered as address 3 when requested Slave Address 143 8F Hex Modbus Function 06 06 Hex Starting Register 3 0003 Hex Page 59 Peak Performer 1 Users Manual Preset Data 3 0002 Hex Request Packet non shaded background denotes the DATA field of the packet i LRC Slave Modbus Starting Register COCASDES 2jo o o ete Response Packet LR
39. T 2 Use the t and keys to navigate and alter the SET value for the Column heater zone to 180 to 200 C 3 After 8 to 12 hours of stable conditioning temperature the column temperature may be restored to the original factory setting See the Final Test Data shipped with the analyzer 4 After normal operating temperature is achieved the front jumper tube may be reconnected between SAMPLE IN and SAMPLE OUT 5 After a 5 10 minute detector re equilibration period samples may be run Normal operating temperatures vary with specific application Consult the Final Test Data for special settings special reconditioning requirements etc for your application 3 3 Detector Conditioning CAUTION The maximum detector operating temperatures for the FID is A 350 C The FID does not normally require conditioning treatment however it does require 8 to 12 hours at normal operating temperature to achieve optimum stable performance Normal detector operating temperature for the FID is 295 C although operating temperatures may vary with the specific application greater than 90 C 1 CAUTION Do not ignite the flame unless the FID FLAME reading is See Section 8 for details concerning the effects of operating parameters temperature and flow on FID detector performance Page 21 Peak Performer 1 Users Manual 3 4 Igniting the FID Flame 1 Verify that Carrier FID H2 and FID Air supply pr
40. UT port is plugged During column reconditioning the plug may be removed and the SAMPLE IN switched to the bypass flow In this manner column reconditioning may be performed without requiring a shutdown of the sample gas flow avoiding the lengthy re equilibration period Page 14 Peak Performer 1 Users Manual 2 5 2 FID Hydrogen H2 Gas Supply H venting He shut off valve and H supply safety equipment must be supplied by customer The analyzer provides a NORMALLY OPEN switch contact for H2 safety purposes The analyzer will close the switch contact CLOSED position temporarily for 120 seconds any time the IGNITE command in invoked lf the FID Flame temperature is greater than the set point value the switch contact will remain closed Any time the FID Flame temperature is less than the set point value the switch contact will revert to the NORMALLY OPEN position automatically see Section 4 7 3 Combustion fuel must be supplied to the Flame lonization Detector The PP1 FID H2 gas connection utilizes a 1 16 female VICI bulkhead labeled FID H on the rear panel 1 Connect the Hydrogen gas supply to the bulkhead and set the source regulator to approximately 25 psig 2 There are no internal regulators in the standard FID PP1 all gas pressures are controlled by external regulators customer supplied FID Hydrogen Gas Specifications High Pressure Cylinder or Hydrogen Generator Gas Type Hydrogen THC
41. W Moves V1 to the Inject position V1 CCW Moves V1 to Load position V2 CW Moves V2 to the In line position V2 CCW Moves V2 to the Vent position ZERO Invokes the detector ZERO command END Ends the Event Program and prepares the analyzer for the next run HEAT ON Not currently in use HEAT OFF Not currently in use Page 38 Peak Performer 1 Users Manual 4 5 2 Event Editor Screen Button Function rs Moves the cursor upwards Moves the cursor downwards Load 1 Allows the user to load the event program 1 Toggle Allows the user to scroll through event program choices Page Advances the user to the next screen 4 6 Stream Selector Program Editor Screen Purchased Option Peak offers a dual sample stream option for most analyzers The selection and timing of sample streams can be pre programmed on this screen NOTE This screen will only appear when the STREAM method of analysis is selected on the RUN screen 12 Stream Selector Program Editor Figure 25 Stream Selector Sequence Screen 4 6 1 Stream Selector Commands The selection of sample streams and appropriate Event Program can be run in a pre programmed sequence Stream Establishes which sample stream to be utilized for analysis Event Prog Establishes which Event Program to be utilized for the sample stream Cycles Establishes the number of repeat analysis before switching to other stream Page 39 Peak Performe
42. a in this field is contained in 16 bit registers Registers are transmitted in the order of high order byte first low order byte second Example e A 16 bit register contains the value 62BE Hex four ASCII characters e High order byte 62 Hex two ASCII characters e Low order byte BE Hex two ASCII characters e This register is transmitted in the order 6 2 B E four ASCII characters e Error Check Field LRC Checksum two ASCII characters Error Check Field In Modbus ASCII mode an 8 bit Longitudinal Redundancy Check LRC algorithm is used to compute the checksum byte The checksum field enables the receiving device to determine if a packet is corrupted with transmission errors The sending device calculates the checksum 8 bit value based on every byte in the packet using the LRC algorithm The calculated value is inserted in the error check field The receiving device performs the same calculation without the error check field on the entire packet it receives The resulting value is compared to the error check field Transmission errors are indicated when the calculated checksum does not equal the checksum stored in the incoming packet The receiving device ignores a bad packet To calculate the LRC 1 Add up all the data bytes in the message before converting to ASCII and without the initial colon and final CR LF 2 Throw away any bits that carry over 8 bits 3 Make the result negative by twos complement to get the LRC by
43. ablish starting and ending points for mathematical analysis of the baseline Page 77 Peak Performer 1 Users Manual All modes of peak are calculation require locating the peak top usually the point of maximum peak signal In cases where the detector signal is strong locating the peak maximum value is straightforward Often the concentration regime of interest is the opposite case where it is desirable to detect and extract the smallest possible peak signal Under these circumstances it is advantageous to utilize signal processing techniques that magnify signal differences Mathematical convolution is one such method Convolution rolls two waveforms together as the product of data matrices with the resulting new waveform having exaggerated characteristics Detector Baseline Cross Multiplied by the Convolution Filter Yields the Resultant Baseline Figure 61 Convolution to Enhance Signal Characteristics As seen in Figure 61 it is much simpler to identify the peak maximum on the convolved baseline Convolution functions work best when the convolving peak filter width closely matches the expected chromatographic peak width Page 78 Peak Performer 1 Users Manual Chromatographic peak width can vary significantly depending upon column selection detector characteristics sample loop size etc Consequenily there are several different convolving peak widths available in the PP1 s mathematics p
44. ackage Flt 1 is the narrowest filter width Flt 8 is the widest filter width NOTE Final determination of the optimum filter width is best performed by re processing chromatograms representing typical peaks 7 6 1 Peak Quantification Baseline Mode When the PkHgt variable is set to zero the Baseline Mode of detector baseline is enabled In this mode the normal detector baseline is calculated very simply Peak start time PkKCen LW Peak end time PkCen RW All other possible aspects of peak start and end time determination are disabled and the normal detector baseline is rigidly established only by the Peak Database parameters Figure 62 Baseline as Established in Baseline Mode Peaks quantified using this method are denoted with an B in the last column of the data report 7 6 2 Peak Quantification Fixed Width Mode The Fixed Width Mode is enabled when the maximum detector signal value at the calculated peak maximum signal is less than the PkHgt parameter value but is greater than zero Page 79 Peak Performer 1 Users Manual The time associated with the peak maximum signal must be within the time regime of interest PkKCen 12 PkWin for any peak quantification to occur In Fixed Width Mode the normal detector baseline is calculated based upon the peak maximum signal time value rather than the PkCen value Peak start time Peak signal maximum time value LW Peak end t
45. ally stored in the folder that matches where the Viewer exe file is stored Page 111
46. c peak The tolerance window is centered upon the PkCen value Variable for establishing the cross over point in peak detection modes Chromatographic peaks higher than this parameter will be quantified using the Variable mode heights peaks with height less than or equal to PkHgt will be quantified using the ForceB mode Convolution filter value expressing the overall peak shape Fit 2 is recommended for sharp narrow peaks such as H2 and FIt 8 is recommended for broad peaks such as CO Valco Instruments Company Inc www vici com Peak Performer 1 Users Manual Table of Contents Introduction Installation Considerations Unpacking Instructions General Considerations Electrical Connections Rack Mount Specifications Gas Supplies and Connections Carrier Gas Supply Carrier Gas Purity Carrier Gas Purity Requirements Carrier Gas Connection FID Hydrogen Gas Supply FID Hydrogen Gas Generators FID Hydrogen Gas Cylinders FID Zero Air Gas Supply Actuator Gas Supply Sample Gas Supply External Calibration Gas Supply Second Sample Supply Calibration Gas Connection for Analyzer with Internal Blender Span Gas Supply For Internal Span Gas Blender Standard Start up Procedure Quick Start Sequence Column Conditioning Detector Conditioning Igniting the FID Flame Sample Analysis Calibration Establishing New Instrument Response Factors Shutdown and Transport Peak Performer 1 Operator Inte
47. ceive the same request command from the master A broadcast request packet is the same as a normal request packet except the slave address field is set to zero 0 All Modbus slave devices receive and execute a broadcast request command but no device will respond The PP1 does not support broadcast request packets Exception Responses lf a Modbus master device sends an invalid command to a PP1 or attempts to read an invalid holding register an exception response is generated The exception response follows the standard packet format The high order bit of the function code in an exception response is set to 1 The data field of an exception response contains the exception error code The table below describes the exception codes supported by the PP1 and the possible causes Return Function Function Description 01 An invalid command is contained in the function field of the request packet The PP1 only supports Modbus functions 03 and 06 Page 61 Peak Performer 1 Users Manual The address referenced in the data field is an invalid address for the specified function This can also indicate that the registers requested are not within the valid register range of the PP1 The value referenced in the data field is not allowed for the referenced register Oo M The LRC checksum is invalid Table 2 Exception Codes supported by the PP1 Exception Response Packet Slave Modbus SS SE PP1 Modbus Registers Map
48. common contaminant in commercial nitrogen sources Hydrogen Carbon Monoxide Carbon Dioxide Hydrocarbons and Moisture carrier gas impurities can be reduced to less than 1 ppb by this type of purifier Page 65 Peak Performer 1 Users Manual Gas Purifier Specifications Heated Reactive Metal Getter Maximum Flowrate gt 300 cc min lt 5 L min Gases Purified N2 Ar He alternative THC Concentration outlet lt 1 ppb CO CO Concentration outlet ee H2 H2O Concentration outlet PR Expected Life Consult Manufacturer 7 3 Component Separation Component separation is normally performed by isothermal packed analytical columns Column materials vary by application and are noted in the test report documentation Contact Peak Laboratories for additional details specific to your application In general applications samples are introduced into the instrument through the SAMPLE IN connection A controlled portion of the sample gas is injected via the pneumatically actuated gas sampling valve into the carrier flow path The injected sample passes onto the head of the analytical column s inside the isothermal column oven and moves through the analytical column where the separation of the components begins The analytes of interest are further refined and methanized on the optional Ruthenium catalyst and continue on to the detector for quantification Page 66 Peak Performer 1 Users Manual CARRIER IN REAR PANEL FFRI INT
49. d It is important to measure the pressure applied to the SPAN GAS IN port as closely to the analyzer rear panel as possible 2 5 6 1 Span Gas Supply Optional For internal span gas blender units only Peak Labs offers an optional internal span gas blender for most analyzers Connection to the SPAN GAS IN port should replicate Figure 8 It is important to measure the pressure applied to the SPAN GAS IN port as closely to the analyzer rear panel as possible Nominal inlet span gas pressure is 50 psig and flow is restricted inside the analyzer External restrictors are not required for these units SPAN GAS FEED SUPPLY Gage TO PP1 SPAN GAS INLET Poke Figure 8 Span Gas Supply Flow Schematic Page 18 Peak Performer 1 Users Manual 3 0 Start up Procedure Peak Labs recommends that the user read the entire operating manual prior to using the Quick Start sequence CAUTION Do not begin detector heating without carrier gas flow Damage to the detector may result 3 1 Quick Start Sequence 1 Confirm that all gas connections and supplies are properly made 2 Remove the top cover of the instrument Figure 9 FID Detector Pressurize the carrier gas supply line to 60 psig Pressurize the FID H2 gas supply to 25 psig Pressurize the FID Air gas supply to 20 psig Pressurize the Actuator gas supply to 65 psig Verify that sample is flowing freely through loop exit flow from the rear SAMPLE OUT port should be 20 t
50. ds from the instrument n Reinstall the analyzer s top cover Page 93 Peak Performer 1 Users Manual Figure 75 Chassis Overview PEAK PERFORMER 1 FID COMPONENT LAYOUT MCPU PCB ASSEMBLY LCD TOUCHSCREEN ASSEMBLY FLOW CONTROL NEEDLE VALVE ASSEMBLY VALVE 1 10 PORT VALVE 2 4 PORT FID H INLET TO FID BASE COLUMN OVEN WITHOUT COVER FID CONTROLLER OCB ASSEMBLY AND COVER _ FID DETECTOR WITH COVER _ FID AIR INLET TO FID BASE REAR PANEL PCB ASSEMBLY INCLUDES MAIN DC POWER SUPPLY O CON DM BWHN PF e e e Page 94 Peak Performer 1 Users Manual 9 1 Peak Performer 1 System Block Diagram Detector oo Power Distribution PCB TOCO uovu cuvAZ Zmmaan Figure 76 PP1 Functional Block and Interconnect Diagram Page 95 Peak Performer 1 Users Manual 9 2 Monitor Regulator Pressures Carrier supply settings should not vary Carrier and Actuator Air settings may shift when supply cylinders run low due to regulator creep and should be checked periodically to maintain consistent gas flows and peak retention times Varying carrier pressures can cause peaks to shift out of set retention times and not be flagged properly Critical operating parameters are listed on the top page of the Final Test Data shipped with the analyzer Peak Labs recommends the user create a logbook of critical parameters on a routine basis as an aid to troubleshooting Suggested
51. ds until the next run is completed As an accessory Peak can provide standard commercial VDC gt mA converters as needed In lieu of a specific concentrations range the RANGE button for the recorder function toggles through choices of raw signal attenuation X1 X2 X4 X8 X16 X64 This function is similar to the RANGE switch on a chart recorder This function only affects the recorder output not the individual compound trends Temporarily over rides the signal output with a known output voltage for test purposes Four MANSET options are available 0 00 VDC 0 25 VDC 0 5 VDC and 1 VDC There is not any zero offset or full voltage scale adjustment within the PP1 if this function is a requirement Peak Labs recommends the use of standard commercial voltage converters attached externally to the analyzer Analog Interface Connections All analog interface connections are made via the rear panel DIN connector To make a proper connection strip all wires back approx 3 8 unscrew the terminal locking screw fully insert the wire and tighten A common error is insufficient length of bare wire creating the condition where the terminal contacts only the wire insulation COM2 A Page 32 e _ SAMPLE SAMPLE 1 N QUT SAMPLE 2 SAMPLE 2 IN uT 9 S 7 6 O U ARIER FID l AJA H2 TO FROM ATOR c N IN NIN crt PA ANALOG 1 ANALOG 2 ANALOG 3 ANALOG 4 ANALOG 5 ANALOG 6 R
52. e Larger sample loops require a long time period to fully inject e The relative values of LW and RW are dictated by the skew factor of the peak e Peaks need about 25 30 data points minimum to be well measured at 5 data points per second this means total peak width should be greater than 6 seconds Therefore it is recommended to use a substantial calibration peak concentration to facilitate easy LW and RW measurements 4 4 2 Analysis Screen Button Function ee Moves the cursor upwards J Moves the cursor downwards Edit Allows the user to enter new peak compound name or analysis parameters Page Advances the user to the next screen Page 37 Peak Performer 1 Users Manual Analysis Averaging When enabled one two or four chromatograms are averaged data point by data point to create a composite chromatogram which is then quantified using normal techniques Analysis averaging does not average concentration data values From analysis start it will take approximately 30 minutes to obtain the best averaged results 4 5 Event Program Editor Screen The Event Program Editor screen stores critical information regarding pre programmed instrument actions needed to perform an analysis Figure 24 Event Editor Screen 4 5 1 Event Program Commands The instrument actions can be pre programmed to create an analysis method or Event Program The analyzer stores up to 4 distinct Event Programs V1 7 C
53. e O2 with polymers at elevated temperatures can easily destroy the valve seals and column packing materials If O2 is being sampled do not exceed 100C for the FID s Column temperature zone and 325C for the Methanizer temperature zone To achieve maximum analyzer performance when measuring O2 samples Peak Labs recommends continuous O2 sample cycling to minimize surface carbon reactions Page 86 Peak Performer 1 Users Manual 8 0 Flame lonization Detector FID CAUTION Do not begin detector heating without carrier gas flow Damage to the detector may result CAUTION The maximum Column temperature is 200 C CAUTION The normal FID operating temperatures is 295 C Maximum temperature is 350 C The FID detector does not normally require conditioning treatment however it does require 8 to 12 hours at normal operating temperature before flame ignition to achieve optimum stable performance Normal detector operating temperature for the FID is 295 C although operating temperatures vary with the specific application The table below illustrates some typical compounds and detection capabilities of the FID Detected Compound Typical Detection Limit Hydrogen No Significant Response Carbon Monoxide lt 10 ppb Carbon Dioxide Other Hydrocarbons Argon Oxygen 8 1 Flame lonization Detector Principles Carrier gas containing the compounds from the column passes directly into mixing tee where H2 for combu
54. e peak area increases by more than 0 5 the mathematics package repeats the process The net effect is illustrated in Figure 66 where multiple hypothetical peak start points were evaluated The final value is represented by point 5 when the change in peak area became less than 0 5 Page 81 Peak Performer 1 Users Manual The trial evaluation of peak area continues for the peak ending point again using a fixed percentage of the LW and RW values as intial baseline points again illustrated as the hypothetical baseline between points L and R in Figure 67 The first hypothetical calculation of the peak end time is labeled 1 in Figure 67 After calculating the hypothetical peak area the mathematics package makes another peak area calculation using a slightly later time value The peak areas of the two calculations are compared and if the peak area increases by more than 0 5 the mathematics package repeats the process The net effect is illustrated in Figure 67 where multiple hypothetical peak start points were evaluated The final value is represented by point 6 when the change in peak area became less than 0 5 Peak Maximum 5 Oo 5 o o N N PEAK START PEAK END Figure 66 Progression of Peak End Time Calculation Using the newly established peak start and end times the mathematics package determines the normal detector baseline as illustrated in Figure 68 The signal
55. econds Minimum value is 3 maximum is 35 RW The typical time span measured from the peak s apex PkCen to the end of the peak s baseline decline in seconds Minimum value is 3 maximum is 35 PkWin Total tolerance window in seconds for assignment of a Name to a quantified chromatographic peak The tolerance window is centered upon the PkCen value PkHgt A variable for establishing the cross over point in peak detection modes Chromatographic peaks higher than this parameter will be quantified using the Variable mode heights peaks with height less than or equal to PkHgt will be quantified using the ForceB mode JJ Fit The convolution filter value expressing the overall peak shape Fit 2 is recommended for sharp narrow peaks such as H2 and Flt 8 is recommended for broad peaks such as CO As a general rule LW and RW values do not change significantly with peak concentration so calibration peak size is not critical in determining proper LW and RW values Page 36 Peak Performer 1 Users Manual T aLeft Width Right Width SF Left Width at Right Width Pag he Width tees rectal Figure 23 Left and Right Peak Width as a Function of Concentration e Total peak width LW RW is primarily a function of sample loop unloading
56. ed Detector Zeroing Target Error Vlamp Low Voltage Out of Range RCP Analyzers Only FID Flame Temperature Out of Range FID Analyzers Only Event Program Load Error Stream Selector Program Error Detector Power Disabled System Parameters Corrupted Parameter Change Update Needed Detector Power Disabled For PDHID amp TCD only 28 Peak Performer 1 Users Manual SN Tr 2014 FEB 05 Methanizer Cio Lurie FIT Flame F I Ul Ll ma t Saud ia at it est t 4 Figure 15 Typical FID Flame Out Error Message All error messages except PARAMETER UPDATE can be cleared at any time by pressing the ACCEPT button However if the error condition continues to exist the error message may re appear Accept Allows the user to acknowledge and clear error messages ie Moves the cursor upwards J Moves the cursor downwards Page Advances the user to the next screen 4 1 4 2 1 Set up Screen Lower Section Button Functions The PARAMETER CHANGE UPDATE NEEDED error message can only be cleared when the analyzer is not performing an analysis i e is in IDLE mode The parameter update action forces a complete re write of permanent memory and is irreversible Peak Labs recommends reviewing all parameter screens before performing a parameter update Page 29 Peak Performer 1 Users Manual Figure 16 Parameter Change Error Message Accept Allows the user to initiate permanent updates t
57. ens a CSV file that was created by the Viewer software Use this command to open a CSV file to view the concentration data Opens serial communication settings window for setting RS 232 Port Settings configurations between the Host PC and the PP1 As shown in figure 34 g NOTE Port number is controlled by host computer and cannot exceed Port 16 Prit Prints all concentration data of selected CSV file O Ei Exit Viewer application 5 5 1 1 Communication Setting Window The Communication Settings window is shown in figure 34 This screen displays the serial communication settings used by the PC to communicate to the PP1 The baud rate data bits and stop bits settings should match all of the settings in figure 16 baud rate 38400 data bit 8 stop bit 1 The COM port number must match the COM port designated by the PC s terminal The COM Port number is determined by which COM port the serial cable is plugged into on the PC not the PP1 Clicking the OK button will configure the COM port to the correct options and save the settings in a file on the computer a Communication Settin Com Port 16 5 F Cancel Baud Rate C 600 f 19200 i 38400 Data Bits Stop Bits i TeS m 2 Figure 34 Viewer Software Communications Setting screen Page 47 Peak Performer 1 Users Manual Once the CSV file is opened the Viewer window automatically updates and shows concentration data Figure 35 is an
58. er Seitings gt Control Panel gt System gt Hardware gt Device Manager to see what the port assignments on your computer are 14 In the Device Manager click on Ports to expand heading so you can see what COM port number your computer gave to the USB to DB9 adapter 15 Note which COM port number is now assigned to the new USB to Serial RS232 Port adapter it s COM4 on most computers 16 Go back to the Viewer window 17 Under File on toolbar select Port Settings 18 Enter COM number assigned to first USB to DB9 adapter probably COM4 check that Baud Rate 38400 Data Bits 8 Stop Bits 1 19 Click OK box to save these settings 20 Communications settings for that USB to DB9 adapter will be saved in the folder and will be used automatically every time you launch the Viewer software in that folder 21 Leave the first Viewer window open 22 Insert second USB to DB9 adapter into USB hub your computer should detect the connection and launch the hardware installation program 23 Insert USB to DBY adapter INSTALL CD in CD drive it will launch automatically if autoplay in enabled on your computer 24 Follow installation instructions that come with USB to DB9 adapter confirm that it is okay to click the Continue anyway box 25 Your computer may prompt to install the USB to DBY adapter a second time do not cancel it is best to let the computer re install the software again 26 Open the seco
59. essures and flows match those listed in the final test report Verify that the FID FLAME temperature is greater than 90C Press the PAGE command 4 times to reach the RUN SCREEN Press the MANUAL command once PN 5 Press the IGNITE command once wait 30 seconds and press the IGNITE command again Press the ESC command once Press the PAGE command once Verify that the FID FLAME MEAS reading is greater than the FID FLAME SET reading if not repeat steps 3 through 8 9 Press the PAGE command 4 times to reach the RUN SCREEN 10 Press the MANUAL command once 11 Press the BIAS command once The screen will display BIAS to indicate that the bias voltage 140 VDC has been turned on OS 3 5 Sample Analysis Verify that sample is flowing freely through loop exit flow from the rear SAMPLE OUT port should be 30 to 120 cc min Press the ESC or PAGE commands as needed to navigate to the RUN screen If multiple sample runs are desired press the SINGLE command to toggle to CYCLE repetitive analysis mode Press the RUN key to initiate analysis the P1 event program will be loaded automatically and executed Allow the analyzer to fully execute the event program Current concentration data will be displayed as an overlay on the RUN screen as peaks are identified and quantified 3 6 Calibration The Peak Performer 1 chro
60. ew software is written specifically for the Peak Laboratories Peak Performer 1 PP1 gas analyzer covering communications port protocols and data formats and is not intended for use with other manufacturer s analyzers 5 1 System Requirements 1 2 GHz 20 GB 256 Mb RAM 1 USB port Windows XP or Windows Vista Windows 7 Windows 8 USB to DBY RS232 Adapter Maker Gigaware Model 26 949 or equivalent DB9 Extension cable DB9M to DB9YF wired straight through 10 feet Optional USB 4 port self powered Hub Inland 08302 or equivalent 5 2 Installing the Peak View Software 1 Place Peak View software CD ROM disk into CD ROM drive 2 If Auto run is enabled follow the installation screen prompts 3 If the CD ROM does not automatically launch select SETUP from CD ROM disk 4 The installation software will auto install the Viewer in a folder under the PC s main drive as the default The user has options from the installation process to create a new folder and install in a new location 5 3 Starting the Peak View Software 1 Double click the Peak View icon on the Desktop or 2 Select START button on the bottom Taskbar 3 Select PROGRAMS select PEAK VIEW and double click to launch move to Peak View 5 4 COM1 COM2 Port and Cable Wiring The cable connected from the PC to the PP1 should be a straight through wired 9 pin M F cable attached to the PC s COM port and the PP1 s COM port See Sec
61. f symptoms e Unstable detector baseline e False positive peaks when measuring pure O2 samples e Difficult small peak quantification e Transient peaks in the chromatogram The chromatographic parameters for the FID O2 analyzers are adjusted to minimize this reactivity the 93 HayeSep D columns used for O2 analysis are unique undergoing an extensive set of proprietary processes for stabilizing the material for O2 service Do not use HayeSep D columns intended for Inert gas sampling in an FID O2 PP1 the detection limit of the analyzer will be severely compromised Additionally the analytical cycle time for the FID O2 analysis is longer than normal The column temperature for FID O2 analyzers is set at 45C to retard the carbon reactions and this creates a longer chromatographic cycle Page 84 Peak Performer 1 Users Manual FID PP1 Stabilization to O2 Samples 600000 O2 Upset Unvented CH4 Peak 500000 At the Start of O2 Sampling 400000 After 0 8 Hours of O2 Sampling After 16 5 Hours of O2 Sampling 300000 After 19 Hours of O2 Sampling Detector Signal Vout 200000 CO2 Peak 100000 0 50 100 150 200 250 300 Time seconds Figure 68 A Sequence of O2 Sample Chromatograms Showing Improvements With Additional Injections Figure 69 overlays several O2 chromatograms over a period of 19 hours The overall chromatogram undergoes a significant shift as more O2 sam
62. gas paths Studying the schematic it can be seen that the detector flow can be adjusted by changing the amount of gas that is allowed to exit via the excess flow vent as more gas exits the excess flow vent less gas is available to flow towards the detector The controlling needle valves for detector flow rate and column venting are co mounted in the chassis for convenience see Figure 61 The detector flow control needle valve is color coded red Differences in DETECTOR flow during normal and venting valve positions can be expressed as shifts in detector baseline Careful adjustment of the detector flow control needle valve will enable the operator to minimize baseline drift and create a smooth chromatogram paca Z 3 far Y alil eee Bes Se C Figure 50 Properly Flow Balanced Detector Baseline Page 70 Peak Performer 1 Users Manual Figure 51 High FID flow from NV1 note rise after the V2 CCW command OFFSET me Aam 3 SPAN in Cone Poi 4 fJ f isl io nm 2 NS Ne L Oftset q 3 E 3 gt se kas IFEI 53 0 Hl i SG Ora Figure 52 Low FID flow from NV1 note drop after the V2 CCW command Differences in COLUMN flow during normal and venting valve positions will be expressed as shifts in peak retention time compared to a chromatogram without any venting action Page 71 Peak Performer 1 Users Manual NV2 Flow 59sccm NV2 Flow 39 sccm _NV2 How 79
63. hanumeric characters A Z 0 9 PkCen The normally expected peak retention time in seconds used for assigning the appropriate Name LW The typical time span measured from the start of the peak s baseline rise to the peak apex PkCen in seconds Minimum value is 3 maximum is 35 RW The typical time span measured from the peak s apex PkCen to the end of the peak s baseline decline in seconds Minimum value is 3 maximum is 35 PkWin Total tolerance window in seconds for assignment of a Name to a quantified chromatographic peak The tolerance window is centered upon the PkCen value NOTE The peak top detection algorithm processes only the data within this window PkHgt A variable for establishing the cross over point in peak detection modes Chromatographic peaks higher than this parameter will be quantified using the Variable mode heights peaks with height less than or equal to PkHgt will be quantified using the ForceB mode JJ Fit The convolution filter value expressing the overall peak shape Flt 2 is recommended for sharp narrow peaks such as H2 and Flt 8 is recommended for broad peaks such as CO For good peak quantification it is important to consistently determine when the peak begins the positive increase in detector signal when the signal maximum occurs and when the peak ends the return to stable detector signal PkCen LW and RW are used to est
64. he late eluting peak carbon monoxide forward Early eluting peaks such as hydrogen are not significantly affected by changes in column temperature as interaction with column packing is minimal Page 73 Peak Performer 1 Users Manual Name Conc Area R Time R Factor A Type H2 413 5 1319343 49 2 3191 V co 343 2 4558519 90 2 13283 V 16 5 Uni 15 81 MS13X FEAK Column Temperature 135 C Carrier Flow 20 5 mi min N2 OFFSET m ATTEN 43a SPAil H r l ma Sem i a ZA H i l wI fi i Fig Lamp Yolahga j E A ae es Analysis Type i TO nen M Variabie wath al el i P a l a Figure 55 Effect of 30C Increase in Column Temperature Column flow rate changes can directly affect peak retention times as peaks are pushed down the column faster or slower Comparison of Figure 57 with Figure 55 shows the decreased peak retention times SS Name Conc Area R Time R Factor A Type H2 136 8 436425 32 4 3191 W CO 201 5 2675877 T1 13283 W 16 5 Uni 15 81 MS13X ASEAK Column Temperature 105 C Carrier Flow 41 2 mlimin N2 oreset ATT 128 spam ne Cons Poly l mn i He a Figure 56 Effect of 2X Increase in Column Flow Rate Page 74 Peak Performer 1 Users Manual 7 6 Peak Identification and Quantification A typical chromatographic peak is generated by the detector s electronic signal as a function of time Vout 2000000 Vout
65. howing Random Baseline Spikes Due to Moisture Page 91 Peak Performer 1 Users Manual 8 4 1 Restriction of Water Flow Out of the FID Drain Line Cause Any restriction or reduction in size lt 4 inside diameter or sagging portion of the FID Drain line can create the opportunity for water bubbles to form with the FID Drain Line These bubbles can create momentary back pressure within the entire FID as they are forced down the drain line to the exit point The induced pressure variations will create random momentary spikes on the FID chromatogram Corrective Actions a Examine the entire FID Drain Line and verify that no reduction in internal diameter occur along it s entire length b Examine the FID Drain Line over it s entire length and verify that no horizontal or Sagging sections where bubbles can form exists c Verify that the exit of the FID Drain Line is not submerged 8 4 2 Moisture Trapped Within the FID Tower Cause The flame within the FID Tower is ignited prematurely at FID Flame lt 90 C or power was lost and the FID Tower temperature dropped below 100 C while the flame was still lit Under these circumstances condensed moisture can become trapped within the FID Tower Trapped moisture can compromise the electrical insulators inside the FID Tower and create false signal readings Corrective Action a Reduce only the FID H2 pressure to zero to eliminate the FID Flame this eliminates the source of mois
66. ime Peak signal maximum time value RW E E 3 x co a Figure 63 Baseline as Established in Fixed Width Mode Peaks are quantified using this method are denoted with an F in the last column of the data report 7 6 3 Peak Quantification Variable Mode If the peak maximum signal value exceeds the PkHogt value the Variable Mode is enabled for determination of peak start and end points The time associated with the peak maximum signal is always calculated first for Forced Baseline and Variable modes by using the convolution filter to find the maximum detector signal point Page 80 Peak Performer 1 Users Manual Oo 5 V N N Figure 64 Initial parameters for Baseline Determination Initially the mathematics package makes a trial evaluation of peak area using a fixed percentage of the LW and RW values as initial baseline points illustrated as the hypothetical baseline between points 2 3 of LW and 2 3 of RW in Figure 65 The hypothetical calculation of the peak start time is labeled L in Figure 66 Peak Maximum a 5 So aed N N PEAK START Figure 65 Progression of Peak Start Time Calculation After calculating the hypothetical peak area based upon the L and R values the mathematics package makes another peak area calculation using a slightly earlier time value The peak areas of the two calculations are compared and if th
67. ince under normal FID chromatographic applications the CO peak is not chemically distinct Peak Labs recommends the use of the RCP models for the measurement of CO as the RCP applications provide chemical specificity for CO measurement Low Level Linearity Measured Concentration as a Function of Blended Concentration Single Mode Flame lonization ppb Measured Concentration O 10 20 30 40 50 60 70 80 90 100 Blended Concentration ppb Figure 70 FID Linearity lt 100 ppb CO CH CO and NMHC Page 89 Peak Performer 1 Users Manual Dynamic Range Measured Concentration as a Function of Blended Concentration Single Mode 20000 18000 Flame lonization Detector 16000 14000 A 12000 10000 5 CO 8000 6000 m CH4 4000 A CO2 a NMHC Measured Concentration ppb O 2000 4000 6000 8000 1000 1200 1400 1600 1800 2000 0 0 0 0 0 0 Blended Concentration ppb Figure 71 FID Response Curve Showing Linear Range 8 3 Detector Flow Rate Effects Carrier gas flow rate through the FID does not influence the rate of CH ionization However the detector response can be influenced by the relative amounts fuel combustion oxygen and inert carrier gas present FID Response With Varying H2 Flow FID Air 200 sccm amp Carrier 55 sccm 140 0
68. key is pressed ReRun Toggle Starting a run in the ReRun mode will recompute the area and concentration based on the parameters in the analysis data base Stream Toggle Starting a run in the Stream mode will configure the PP1 to initiate the Stream Selector Sequence until the Idle key is pressed Page Advances the user to the next screen 4 7 2 Continuous Monitoring Analysis Continuous monitoring is intended for on line analysis or other applications which ReRun analysis is not required Use the PAGE key to scroll to reach the Run screen Toggle the Single Cycle ReRun key until Cycle appears see Figure 28 Press Run to initiate a repetitive analytical cycle By pressing the RUN key event program 1 P1 is automatically loaded and the system will begin to collect data in repetitive mode see Figure 28 To halt the cycle pressing the IDLE will cause the analysis run to cease immediately Toggle between the Single Cycle Rerun or optional Stream to select the next mode of analysis 4 7 3 Manual Screen Sub Screen of the Run Screen The Manual sub screen allows the operator to invoke all the event program commands on demand Zero Ignite Bias vi U2 a Ese Figure 29 Run Manual screen Page 42 Peak Performer 1 Users Manual 4 7 3 1 Manual Screen Button Functions Zero Pressing this key will electronically zero the detector Ignite Pressing this button applies power to
69. l y 7 Figure 85a Main DC Power Supply Location Remove the 4 each 6 32 screws that hold down the plastic protective shield to expose the DC power supply see Figure 84 Figure 85b Main DC Power Page 105 Peak Performer 1 Users Manual Figure 86 Main DC Power Supply with Shield Removed Unscrew the 4 each 4 standoffs that retain the DC power supply to the rear panel circuit board Disconnect only the two cable assemblies that attach the DC power supply to the rear panel circuit board it is recommended to disconnect the cables at the circuit board connector end Remove the DC power supply by sliding it under the overlayed cable assemblies do not remove the other cable assemblies see Figure 85 Page 106 Peak Performer 1 Users Manual ONN A a CE z TA pee yee ee al 1 eomma a ei st E othe ER meee Tl toad PEAK LABORATORIES REAR PANEL INTERCONNECT 484 001 Rev Figure 87 Main DC Power Supply Fully Removed Lay the old DC power supply on the workbench aside the new Power one DC power supply Orient such that the 6 pin and 2 pin connectors are aligned see Figure 86 Old Versions of DC Power Supplies Figure 88 Correct Alignment and Cable Transfer from Old to New DC Power Supply Transfer the two cable assemblies from the old power supply to the new supply Install the new DC Power Supply by reversing the disassembly sequence After ins
70. m Relay The FID Flame and General Alarm switch relays are SPST N O and rated 0 5 amps 200VDC 10VA Viewer NOTE The Analog recorder signal is only active when the COM1 setting is set to DETECTOR OUT REMOTE START FLAME SW GENERAL ALARM SW GENERAL ALARM AND FLAME SWITCH RATED AT 0 5 A 120V Figure 20 Analog are Wiring Schematic Channels 1 7 output voltage can be tested manually by pressing the MANSET key to send a temporary signal for diagnostics Page 33 Peak Performer 1 Users Manual 4 3 Calibration Database Screen The Calibration Database screen stores critical information regarding calibration Span gas concentrations and instrument response and provides tools to easily update the response factors Po 4 s CANDIL 0 JEOLN Ji Update Figure 21 Calibration Database Screen 4 3 1 Calibration Screen Button Function Update Allows the analyzer to calculate new RFactor ie Moves the cursor upwards Le Moves the cursor downwards Edit Allows the user to change concentration data or response factor Page Advances the user to the next screen 4 3 2 Calibration The Peak Performer 1 chromatograph determines concentration peak area to quantify the amount of contaminants in the sample gas The direct instrument response in units of uV sec is reported simultaneously as an overlay on the RUN CHROMATOGRAM SCREEN and in the AREA column on the
71. matograph determines concentration peak area to quantify the amount of contaminants in the sample gas The direct instrument response in units of uV sec is reported simultaneously as an overlay on the RUN CHROMATOGRAM SCREEN and in the AREA column on the CALIBRATION DATABASE SCREEN As the concentration peak area is determined the analyzer applies the pre programmed response factor as an inverse proportional factor to generate the reported concentration value PEAK CONCENTRATION PEAK AREA RESPONSE RESPONSE FACTOR Page 22 Peak Performer 1 Users Manual 3 6 1 Establishing New Instrument Response Factors Connect a known calibration standard gas span gas to the analyzer at the SAMPLE IN port on the front panel If soan gas connection is made at the rear panel SAMPLE IN port ensure that the front jumper is connected between SAMPLE OUT and SAMPLE IN on the front panel Verify that sample is flowing freely through loop exit flow from the SAMPLE OUT should be 30 to 120 cc min Press the ESC or PAGE keys as needed to navigate to the RUN screen Press the SINGLE CYCLE RERUN key to toggle to SINGLE mode Press the RUN key to initiate analysis the P1 event program will be loaded automatically and executed Allow the analyzer to fully execute the event program Current concentration data will be displayed as an overlay on the RUN screen as peaks are identified and quantified Press the PAGE key as needed to toggle to the CA
72. me lonization Detector FID 87 8 1 Flame lonization Detector Principles 87 8 2 Temperature Effects Within the Methanizer and FID Tower 89 8 3 Detector Flow Rate Effects 90 8 4 Resolving Random Spikes on the FID Baseline 91 8 4 1 Restriction of Water Flow Out of the FID Drain Line 92 8 4 2 Moisture Trapped Within the FID Tower 92 9 0 Analyzer and FID Maintenance and Service Procedures 94 9 1 Peak Performer 1 System Block Diagram 95 9 2 Monitor Regulator Pressures 96 9 3 Verifying Valve Integrity Carrier Blank Zero Gas 97 9 4 Start up Sequence for Replacement Methanizer 98 9 5 Adjusting the Display Contrast 102 9 6 Altering the Analytical Range of the Instrument 103 9 7 Testing the Heater Resistance 104 9 8 Main DC Power Supply Replacement 105 9 9 Adjusting the 5 Volt DC Power Supply 108 9 10 COM 1 Viewer Connections on Multiple Analyzers to a 109 Single Computer Page 6 Peak Performer 1 Users Manual PEAK PERFORMER 1 keb BAR 1 0 Introduction The Peak Laboratories Peak Performer 1 PP1 FID gas analyzer is a trace level gas analysis system capable of detecting part per trillion ppt concentrations of Hydrocarbons gases in a variety of sample matrices Due to the specific nature of the detection method analysis times are rapid and chromatographic complexity is minimized The result is a simple and reliable system capable of following rapid trends in component concentration in laboratory field and process gas applications
73. nd new folder and select the Viewer exe file in that folder 27 Double click to launch Viewer exe you might get a COM port error message window simply click OK and proceed 28 Go to Windows Device Manager gt Settings gt Control Panel gt System gt Hardware gt Device Manager to see what the additional port assignment on your computer is 29 In the Device Manager click on Ports to expand heading so you can see what COM port number your computer gave to the second USB to DB9 adapter it will be displayed directly under the note for the first USB to DB9 adapter Page 110 Peak Performer 1 Users Manual 30 Note which COM port number is now assigned to the second USB to Serial RS232 Port adapter its COM5 on most computers 31 Go back to the Viewer window 32 Under File on toolbar select Port Settings 33 Enter COM number assigned to second USB to DB9 adapter probably COMS check that Baud Rate 38400 Data Bits 8 Stop Bits 1 34 Click OK box to save these settings 35 Communications settings for that USB to DB9 adapter will be saved in the folder and will be used automatically every time you launch the Viewer software in that folder 36 Viewer should automatically connect to the other analyzer At this point you should have two Peak Host windows open connected to the different analyzers If you run the analyzers the chromatographic data for each analyzer will be automatic
74. ntration sample balance peaks For optimum performance the carrier gas must match the balance gas of your analytical sample although other carrier gases can be used for specific applications with factory assistance PLEASE CONSULT THE TEST DATA ATTACHED TO YOUR ANALYZER IF UNCERTAINTY OF CARRIER GAS SELECTION EXISTS Page 12 Peak Performer 1 Users Manual 2 5 1 1 Carrier Gas Purity Chromatographic instrument detection limit is directly related to carrier gas purity Improved carrier gas purity enables improved sensitivity Typical Nitrogen 5N Gas Specifications Pre Purification High Pressure Cylinder or Liquid Dewar Gas Type No Ar He alternative Consequently the analyzer s minimum detectable quantity MDQ would be quite high gt 10 ppm unless the carrier gas is purified Peak recommends use of the best quality heated metal getter purifier available for carrier gas purification This style of purifier typically has a hot catalyst element ahead of the heated getter material for complete removal of methane hydrocarbon CH3 a common contaminant in commercial nitrogen sources Hydrogen Carbon Monoxide Carbon Dioxide Hydrocarbons and Moisture carrier gas impurities are reduced to less than 10 ppt by this type of purifier Typical Heated Metallic Getter Purifier Specifications No Ar He alternative CO CO Concentration outlet SIPPY H2 H2O Concentration outlet SARPA Expected Life Consult Manufact
75. o 120 cc min 8 Verify BYPASS OUT flow gt 20 cc minute 9 Verify the analyzer is connected to the correct line voltage supply 10 Energize the main power switch located to the right of the power cable see Figure 1 11 After energizing the instrument will display the MAIN screen in the IDLE state So 2 Page 19 12 13 14 15 Peak Performer 1 Users Manual Set Date and Time Press command three times to position the cursor in the middle 1 3 of the screen Press the HEAT command once to activate heater zones Allow the 4 6 hours for the analyzer to thoroughly stabilize the heated zones After temperature stabilization 16 17 18 19 20 21 22 23 24 20 26 A 21 3 2 Verify that the FID FLAME reading is greater than 90 C lf the analyzer has been stored or idle without carrier gas flow for more than a few days consider column conditioning as described in Section 3 2 Press the PAGE command 4 times to reach the RUN SCREEN Press the MANUAL command once Press the IGNITE command once wait 30 seconds and press the IGNITE command again Press the ESC command once Press the PAGE command once Verify that the FID FLAME MEAS reading is greater than the FID FLAME SET reading if not repeat steps 18 through 22 Press the PAGE command 5 times to reach the RUN SCREEN lf automatic sample cycles are desi
76. o non volatile memory 1 Moves the cursor upwards J Moves the cursor downwards Page Advances the user to the next screen Pressing the ACCEPT button alters the screen appearance SN TT Methanizer LoL urnir FID Flame FID Hout Parameter Figure 17 Parameter Change Prompt Page 30 Peak Performer 1 Users Manual Save Allows the user to make changes to permanent non volatile memory Esc Aborts updates to non volatile memory 4 2 Analog Interface Trend and Recorder Output Screen The compound or Channel information for the ANALOG INTERFACE screen is automatically populated using the information from the ANALYSIS DATABASE screen NOTE The analog outputs are locked if the Port 1 Protocol on the MAIN SCREEN is set to DETECTOR See Section 4 1 1 Analog signals generated from this information appear on the rear panel s green DIN terminal blocks See Figure 19 Figure 18 Analog Interface Screen 4 2 1 Analog Interface Screen Button Function ier Moves the cursor upwards Moves the cursor downwards Range Allows the user to select the full scale concentration range associated with the maximum 1 00 VDC signal for each compound The ranges are user selectable e g 0 1000 ppb readings in the analyzer 0 1 00 VDC output scale Page 31 4 2 2 Manset Peak Performer 1 Users Manual At the end of each run the analog signal is updated and hol
77. o repair the instrument except under directed to do so by factory trained service technicians Permanent damage and voiding of the warranty may result of improper operation The FID utilizes low flows of pure hydrogen and clean air to generate a small continuously burning flame within the FID Tower Use standard gas handling practices for combustible gases when working with the FID equipped PP H2 venting H2 shut off valve and H2 supply safety equipment must be supplied by customer Page 2 Peak Performer 1 Users Manual Glossary and Terms FID Methanizer HSD Molecular Sieve Unibeads Gas Purity Gas Response Factor Name PkCen LW RW PkWin PkHgt Fit VICI Page 3 Flame lonization Detector Ruthenium Oxide Catalyst HayeSep D column packing material Zeolite column packing material Silica column packing material Amount of undesired elements in a gas supply Span Gas supply with known certified amounts of specific compounds Proportionality factor between area count units and concentration units Peak identification tag Expected peak retention time in seconds Typical time span measured from the start of the peak s baseline rise to the peak apex PkCen in seconds Typical time span measured from the peak s apex PkCen to the end of the peak s baseline decline in seconds Total tolerance window in seconds for assignment of a Name to a quantified chromatographi
78. of adequate ventilation and make sure the cooling fan inlet is unobstructed The operating environment for the PP1 analyzer should be maintained between 15 C and 30 C 2 4 Rack Mount Specifications The PP1 is designed for mounting in a standard 19 instrument rack The analyzer occupies 4U 6 9 of panel height 26 in depth Rack retaining flanges provided with the Peak rack mount kit attach via the analyzer top cover to provide secure connection to the instrument rack rails Peak recommends use of high quality 26 full extension ball bearing slides for instrument mounting such as Jonathan QD375 26 or equivalent Figure 2 Rack Mount Front View with Dimensions Peak Performer 1 Users Manual aACTUATOR i i f BAS j IN f CARRIER i ff IN H F ADAIR if eee oa oe oe ote oe Figure 3 Rack Mount Rear View with Dimensions Figure 4 Rack Mount Top View with Dimensions Page 10 Peak Performer 1 Users Manual 2 5 Gas Supplies and Connections All plumbing connections are 1 16 female VICI bulkhead fittings The Peak Performer 1 is shipped with tubing and fittings required to connect the analyzer to gas sources Replacement materials are available from Peak Laboratories or may be purchased directly a Standard gas fittings are 1 16 VICI compression fittings VICI P N ZN1 amp ZF1 b Supply tubing is 1 16 O D x 0 03 I D cleaned and baked T300 stainless
79. parameters for frequent logging are e Analyzer S N e Date and Time e Carrier Gas Type e Carrier Gas Supply Pressure e Carrier Gas Flow at Front Panel Bypass Out Port e Carrier Gas Flow at NV1 Outlet V1 CCW e Carrier Gas Flow at NV2 Outlet V1 CCW e FID H2 Gas Supply Pressure e FID Air Gas Supply Pressure e Actuator Gas Supply Pressure e Sample Gas Type e Sample Gas Flow at Rear Panel Sample Out Port e Column Set point and Measured Temperature e Detector Set point and Measured Temperature e FID Vout Signal after zeroing e FID Flame Reading e Rfactor for compounds 1 2 3 amp 4 from Calibration Database screen e PkCen for compounds 1 2 3 amp 4 from Analysis Database screen Other critical parameters that should be verified occasionally e Actuator Gas Type e Port 1 Protocol Setting e Port 2 Protocol Setting e Calibration Database Screen Parameters all e Analog Interface Screen Parameters all e Analysis Database Screen Parameters all e Event Program Editor Screen Parameters for all active Event Programs Page 96 Peak Performer 1 Users Manual 9 3 Verifying Valve Integrity Carrier Blank Zero Gas In addition to periodic calibration checks the integrity of the rotary valve seal must be tested Determination of valve seal quality is performed by analyzing known purified gas as a sample 1 Connect the front panel SAMPLE IN port to the front panel BYPASS OUT port This
80. ples are taken e Decreasing magnitude of the O2 upset e Improved baseline resolution at the CH4 peak leading edge e Improved baseline stability at the CH4 peak trailing edge e Improved baseline stability at the CO2 peak retention time Each of these chromatographic changes will directly enhance the lower detection limit of the analyzer by making it easier to clearly define peak start end points and peak magnitude These chromatographic improvements occur as the free carbon on the internal surfaces of the analyzer system is consumed Many of the sources i e polymeric valve seals do not become carbon free over time however the available surface carbon can become greatly diminished with continuous exposure to O2 Free carbon may reside within the main body of materials in the system and diffusion forces may bring this carbon load to the surface again during idle analyzer times Consequently it is not unusual to see these instabilities reappear in a previously clean system after extended periods of inactivity The new free carbon can again be diminished by continuous exposure to O2 CAUTION Under certain circumstances the reduction of the analyzer surface carbon may be accelerated with above normal operating temperatures Page 85 Peak Performer 1 Users Manual and continuous exposure to O2 As a general rule O2 conditioning temperatures are much lower than standard conditioning temperatures the high reactivity of pur
81. r 1 Users Manual 4 6 2 Stream Selector Program Editor Screen Button Function ie Moves the cursor upwards J Moves the cursor downwards Edit Allows the user to chose event program and of repetitions Page Advances the user to the next screen 4 7 Run Chromatogram Screen The Run Chromatogram screen provides the real time display and data processing of sample analysis The screen displays the running chromatogram peak markers and concentration data The information displayed on this screen is useful for evaluating instrument health event program validity and analytical stability Figure 26 Run Chromatogram screen in the Idle state and the mode displayed upon initial power up Page 40 Peak Performer 1 Users Manual Figure 27 Run screen in Single mode with chromatogram being drawn wort 10 Attn 7 192 sec 4267319 1806 4 ro I nitel Bias U1 U2 a lEse Figure 28 Run screen in Idle mode at end of run 4 7 1 Run Screen Button Functions Run Loads a standard event program and runs an analysis in the mode selected Idle Stops the analysis immediately Manual Opens the Manual Run Screen Disp Opens the Display Screen Single Toggle Starting a run in the will command the PP1 to run one time and return to the idle mode Page 41 Peak Performer 1 Users Manual Cycle Toggle Starting a run in the Cycle mode will configure the PP1 to run continuously until the Idle
82. r section 3 lines contains commands related to analyzer set up 2 The middle section 5 lines contains commands related to temperatures zones and detector parameters 3 The lower section is reserved for error messages and non volatile memory updates 4 1 1 Set up Screen Upper Section Figure 11 Main or Setup Screen Upper Section 4 1 1 1 Set up Screen Upper Section Button Functions Ts Moves the cursor upwards 3 Moves the cursor downwards Edit Allows the user to change the Date Time or Protocols Page Advances the user to the next screen Page 25 Peak Performer 1 Users Manual 4 1 2 Set up Screen Middle Section Power up The middle section of the Setup screen is concerns temperature zone and detector function Ver 3 88 oH rr DateTime 2614 FEB G6 ljewer Auto flebharnizer Column FID Fl ane FID Hout Figure 12 Screen Commands Upon Power up NOTE The heater zones are not energized automatically upon power up and the detector electronics are not fully initialized until the ZERO command is invoked 4 1 2 1 Set up Screen Middle Section Button Functions Power up If both heater zones are de energized the following command buttons are available Zero Allows the initialize the detector electronics and establish a consistent baseline signal Moves the cursor upwards Moves the cursor downwards Edit Allows the user to energize each heate
83. r zone or change heater setpoint temperatures Heat Energizes all the heater zones Page Advances the user to the next screen Page 26 Peak Performer 1 Users Manual 4 1 3 Set up Screen Middle Section Normal The middle section of the Setup screen concerns temperature zone and detector function Figure 13 Screen Commands After Warm up 4 1 3 1 Set up Screen Middle Section Button Functions Normal Zero Allows the initialize the detector electronics and establish a consistent baseline signal i Moves the cursor upwards ie Moves the cursor downwards Edit Allows the user to energize de energize each heater zone or change heater set point temperatures Page Advances the user to the next screen Page 27 Peak Performer 1 Users Manual 4 1 4 Set up Screen Lower Section The lower portion of the Setup screen is reserved for error messages and non volatile memory updates 4 1 4 1 Error Messages on the Set up Screen Lower Section All error conditions are enunciated by a RED color on front panel LED and a shift in the ERROR FLAG parameter transmitted through the COM1 and COM2 output ports see section 6 1 for additional details Figure 14 Set up Screen Displaying an Error Message There are eleven individual error conditions that can cause the status LED on the front panel to glow red Page Detector Communication Error Temperature Zone Out of Range Temperature Zone Disabl
84. red press the SINGLE command once to change the setting to CYCLE To initiate sampling press the RUN command once The FID bias voltage will be energized automatically and the P1 event program will be automatically loaded and run Cycle samples with SAMPLE IN connected to BYPASS OUT on the front panel See Step 17 to start CYCLE process NOTE To display concentration data only press the upper right corner of the RUN screen once this will hide the chromatogram and display data in large text format To reveal the chromatogram again press the upper right corner of the RUN screen again To halt sampling press the IDLE command once Column Conditioning Conditions warranting column reconditioning are a Start up after storage shipment b Reduced detector response c Unstable baseline d Merging of peaks Normal column operating temperatures are 45 to 90 C The maximum PP1 FID column operating temperature is 105 C when exposed to oxygen bearing gases A CAUTION Never energize heaters of the instrument unless carrier gas flowing Page 20 Peak Performer 1 Users Manual CAUTION The maximum PP1 FID column operating temperature is 105 C when exposed to oxygen bearing gases Do not exceed 210 C of column oven temperature at any time Temperatures in excess of 210 C can destroy column material 1 Connect the front jumper tube between SAMPLE IN and BYPASS OU
85. rface Set up Screen Set up Screen Upper Section Set up Screen Upper Section Button Functions Set up Screen Middle Section Power up Set up Screen Middle Section Button Functions Power up Set up Screen Middle Section Normal Set up Screen Middle Section Button Functions Normal Set up Screen Lower Section Error Messages on the Set up Screen Lower Section Clearing Error Messages on the Set up Screen Set up Screen Lower Section Button Functions Analog Interface Trend and Recorder Output Screen Analog Interface Screen Button Function iN Oo N h Page 5 Peak Performer 1 Users Manual Analog Interface Connections Analog Interface Wiring Breakdown Calibration Database Screen Calibration Screen Button Functions Calibration Establishing New instrument Response Factors Analysis Database Screen Analysis Database Parameters Analysis Screen Button Function Event Program Editor Screen Event Program Commands Event Editor Screen Button Function Stream Selector Sequence Editor Screen Optional Stream Selector Commands Stream Selector Program Editor Screen Button Function Run Chromatogram Screen Run Screen Button Functions Continuous Monitoring Analysis Manual Screen Sub Screen of Run Screen Manual Screen Button Functions Display Screen Sub screen of Run Screen Display Screen Button Functions Peak View Software System Requirements Installing the Viewer Software Starting the Viewer Software COM1
86. rs High Order Register value 65536 Low Order Register value modulus 65536 Page 60 Peak Performer 1 Users Manual Example Unsigned 32 bit Value 12345678 is passed in unsigned 32 bit integer format 12345678 0OBC614E Hex High Order OOBCHex Low Order 614EHex Example Signed 32 bit Value 12345678 is passed in signed 32 bit integer format 12345678 FF439EB2 Hex High Order FF43 Hex Low Order 9EB2 Hex Packed Boolean Format Boolean registers are packed into a single Modbus register The boolean outputs corresponds to one bit in the single output register of the module The relationship is left to right the first input register corresponds to the left most bit in the 16 bit output register etc Example Packed Boolean Format Six Boolean registers are linked to a single Modbus register which is configured for Packed Boolean output format If the first three are valued False and the remaining three are valued True the output register value is Register 0001110000000000 Bin 1C00 Hex lf the first input register became True the output register value changes to Register 1001110000000000 Bin 9C00 Hex 8CharString Format The 8CharString or eight character string register format is four 16 bit Modbus Holding Registers that hold a total of eight ASCII characters 6 4 5 Broadcast Packets The purpose of a broadcast request packet is to allow all slave devices to re
87. stion and methanization is added At the heated flame tip with the FID tower this gas stream is bathed in a cylindrical flow of combustion air and the H2 O2 flame is ignited Within this flame the following general reactions occur reactions are left unbalanced for simplicity Page 87 Peak Performer 1 Users Manual H gt Oo gt H2O Heat and CH Oo Heat gt CHO HO Depending upon operating parameters this reaction releases electrons until the end reaction products are reached These electrons are collected and the resulting current measurement is used for quantification The net result is in simplest terms that electrons are released in direct proportion to the number of carbon atoms present C3Hs Oo Heat gt S3CHO HO 3e Therefore instrument response is directly proportional to the number of carbon atoms present in the compound being measured Unfortunately the ionization efficiency of the flame is relatively low and roughly 1 in 10 000 hydrocarbon molecules follows the electron liberating reaction path described The vast majority of combustion reactions follow the direct net product reaction 2CH 402 gt 2C0O 2 4H20 Heat This reaction sequence is applicable to any hydrocarbon It can be seen that the FID is a mass flow type of detector the number of ions created is independent of carrier flow therefore detector response is the same regardless of carrier flow rate
88. t the CONC field or all updates will be lost With the before the compound name press the UPDATE key The analyzer will recalculate the appropriate response factor for the compound based upon the span gas concentration and analyzer area response using the following formula RESPONSE FACTOR AREA RESPONSE SPAN GAS CONCENTRATION NOTE The LED on the analyzer s front panel will change from green to red to remind the user that the current calibration information is stored in volatile temporary memory only and will need to be saved to permanent memory at a later time Repeat the sequence for each of the compounds shown on the CALIBRATION DATA BASE screen Repeat analysis of the span gas sample and verify that the analyzer reports data values within normal calibration tolerances i e 5 Page 35 Peak Performer 1 Users Manual The Analysis Database screen stores critical information regarding peak identification and quantification parameters Analysis Database 2 AAA SAAG 18686 6 dr Analysis Averading 1 tt ea Figure 22 Analysis Database Screen 4 4 1 Analysis Database Parameters Name The peak identification tag expressed as 5 alphanumeric characters A Z 0 9 PkCen The normally expected peak retention time in seconds used for assigning the appropriate Name LW The typical time span measured from the start of the peak s baseline rise to the peak apex PkCen in s
89. ta command to Host from PP1 6 3 Port 2 Protocol There are two COM2 protocol formats PLC programmable logic controller and MODBUS protocols There are three modes of operation AUTO POLL and MODBUS PLC protocol can operate in 2 modes AUTO or POLL The MODBUS Protocol mode is predefined and not user changeable Proper selection of protocol is determined by the application in use on the host computer 6 3 1 COM 2 Port Settings The RS 232 settings for COM 2 port are 9600 baud rate 8 bit data 1 stop bit and no parity for AUTO and POLL modes The RS 232 settings for COM 2 port in MODBUS mode are 9600 baud rate 7 bit data 1 stop bit and even parity for Page 55 Peak Performer 1 Users Manual Three modes of transmission are available AUTO or POLL or MODBUS e In AUTO mode the current PLC data string is transmitted at the end of analytical cycle without any request from the host computer e In POLL mode the PP1 will transmit the latest PLC data string only when prompted by the host computer This mode is recommended for use in a RS 485 network but can also be used for RS 232 connections e In MODBUS mode the PP1 will transmit the latest PLC data string only when prompted by the host computer See MODBUS uses manual for operational details Selecting the POLL mode on the MAIN SCREEN configures the PP1 to wait for a request before transmitting The master controller of the RS 485 network must first request data from the PP1
90. tallation and power up it may be necessary to re adjust the contrast on the front panel display it may be too light or too dark Page 107 Peak Performer 1 Users Manual 9 9 Adjusting the 5 Volt DC Supply Adjust this potentiometer so that the volatge is between the RED and BLACK wires at 5 1 to 5 2 VDC Ji4 J3 AC DET AC CAP OVEN Please Note Adjustments are not applicable for newer analyzers Rev L and above Please contact your local representative for details Figure 89 Adjusting the 5 Volt DC Supply Page 108 Peak Performer 1 Users Manual 9 10 COM 1 Viewer Connections on Multiple Analyzers to a Single Computer Equipment 1 each Computer 1 2 GHz 20 Gb Hard drive 256 Mb RAM CD R drive with at least 1 USB port Dell Inspiron 8500 laptop or equivalent Operating System Windows XP Home Edition v2002 Service Pack 1 1 each USB Hub Inland 4 Port USB Hub Self powered Stock 08302 manufactured by Inland International www inland products com 2 each USB to DBY RS232 Adapter SIIG Inc USB to Serial Adapter Model US2308 Part JU CB1S12 manufactured by SIIG Inc www siig com Comes with installation software 2 each DBY Extension Cable DB9M to DBYF wired straight through 10 feet long GQ Cables 10 Mouse Keyboard Extension DB9M to DB9YF Part M05 103 a USB Hub USB to DB9Y aes A T TTN oooo oooo Figure 90 Multiple Analyzers Connected to a
91. te 4 Convert from the 8 bit hex value to two ASCII characters 6 4 3 Packet Communications The PP1 analyzer only supports two Modbus functions Read Holding Registers and Preset Single Register Function codes 03 06 respectively Modbus Function ModBus Description Function Description Read Holding Fetch the current value in one or more holding registers Registers from the PP1 Preset Single a a oe a P an aai values into a single holding register to the Table 1 Modbus Functions Supported by the PP1 as a Slave Function 03 Read Holding Registers To read PP1 parameter values a Master must send the PP1 a Read Holding Registers request packet The Read Holding Registers request packet specifies a starting Page 58 Peak Performer 1 Users Manual address and the number of 16 bit registers to read The Modbus registers are numbered from 40001 to 49999 This Modbus numbering corresponds to an address map of 0 to 9998 The PP1 responds with a packet containing the values of the registers in the range defined in the request See PP1 address map table to verify address range and content Read Holding Registers Packet Example The next example the PP1 s Modbus slave address is 92 and the master requests to read two parameters from the PP1 These two parameters are requested from Modbus registers 40013 and 40014 In accordance with the Modbus protocol holding register 40013 is numbered as address 12 when requested
92. tion 6 for details on communications protocols Page 44 Peak Performer 1 Users Manual 5 5 Viewer Software Window The Viewer window shown in Figure 33 shows the main Viewer screen with a RED DOT in the upper right corner This RED DOT signifies that there is a connection problem with the PC and the PP1 Verifying the following can solve this connection problem Communication Settings Connection of 9 pin cable between PC and PP1 RS 232 cable plugged into the PP1 s COM 1 port PP1 is powered off After the connection problem has found and corrected the RED DOT should be CLICKED to verify if communication between the PC and PPican be properly established a PeakView Ver 5 File Start Stop Chrom View Event Info Upload Run Time Stream Figure 31 Viewer main window showing Communications Error The Viewer window shown in Figure 32 shows the viewer screen without the RED DOT This signifies the communication connection between the PC and the PP1 is function correctly Page 45 Peak Performer 1 Users Manual File Start Stop Chrom View Event Info Upload Run Time Stream Figure 32 Viewer main window showing no Communications Error 5 5 1 File Menu on the Viewer Taskbar ri PeakView Ver 5 08 Start Stop Chrom View Event Info Upload Open Port Settings Print Figure 33 File Menu on the taskbar Page 46 Peak Performer 1 Users Manual The File menu contains the following commands Op
93. tly supports one command from a host computer system This command remotely starts a RUN The PP1 system processes the external start command only if the analyzer is in IDLE mode Not running a sample Upon receipt of the external start command the PP1 performs the following functions e Sets system run mode to SINGLE RUN mode e Loads event program P1 e Starts a Single Run e Sends Detector Signal Data stream i e Vout reading to the COM1 port e Atthe end of the run the PP1 sends an End Of Data string to identify the end of the data stream e Sets analyzer to IDLE mode and waits for the next start command 6 2 3 1 External Start Command String The External Start Command string format transmitted by host computer must consist of three ASCII characters Below are four forms of the same command Form 1 Start Of Text S End Of Text Form 2 STX S EXT Page 54 Peak Performer 1 Users Manual Form 3 SB S Form 4 02 53 03 6 2 3 2 Detector Signal Data String The PP1 Detector Signal Data string format is a decimal number followed by a carriage return CR and line feed LF An example 104345 104763 104832 The End Of Data string format consists of three ASCII characters The following are four forms of the same command Form 1 Start Of Text E End Of Text Form 2 STX E EXT Form 3 ABE AC Form 4 02 45 03 An example 104345 104763 104832 Last sample sent to Host BE C End Of Da
94. ture within the FID Tower Keep all other flows as normally specified b Increase the Methanizer temperature to 350 C for 8 to 16 hours to thoroughly heat the FID Tower and drive out trapped moisture c After 8 to 16 hours restore the Methanizer temperature to 295 C restore FID H2 flow and re ignite the flame On occasion moisture can also become trapped under the FID Tower Cap at the O ring seal This moisture can be eliminated by simply removing and restoring the FID Tower Cap the act of removal shifts the O ring enough that the moisture is ejected To perform this action d Reduce only the FID H2 pressure to zero to eliminate the FID Flame this eliminates the source of moisture within the FID Tower Keep all other flows as normally specified e Remove the analyzer top cover f Remove the single retaining screw on the top of the FID Oven Cover g Gently pull back any insulation that covers the top of the FID Tower h Remove the 14 hexagonal standoff that retains the FID Tower Cap i Using a pair of pliers the cap is roughly 100 C gently rock and lift the FID Tower Cap approximately 1 2 until it is completely clear to the FID Tower top surface Page 92 Peak Performer 1 Users Manual j Replace the FID Tower Cap on the FID Tower and rock gently the cap down into position k Reinstall the 1 hexagonal standoff Replace any insulation m Reinstall the FID Oven Cover Vacuum any loose insulation shre
95. urer Page 13 Peak Performer 1 Users Manual 2 5 1 2 Carrier Gas Purity Requirements Gas Supply a Purity Soldat Typical Flow Nitrogen l lt 1 ppb total Carrier ph Seni a i 60 psig 150 sccm UHP Grade lt 10 ppb THC Oo PeO Hydrogen lt 1 ppm H2O 29 psig Combustion Medical Clean Dry Air lt 10 ppm Heated reactive metal getters are the only proven reliable technique for generating the specified carrier gas purification Cold metallic getters and absorption getters do not reliably remove all common critical bulk gas contaminants 2 5 1 3 Carrier Gas Connection The PP1 carrier gas connection utilizes a 1 16 female VICI bulkhead labeled CARRIER IN on the front or rear panel 1 Connect purified N2 carrier gas supply gas Ar He alternative to the carrier bulkhead and set the source regulator to the settings shown in final test data 2 There are no internal regulators in the standard FID PP1 all gas pressures are controlled by external regulators customer supplied 3 Verify detector flow with a flow meter to roughly match the settings in the final test data 4 Verify the BYPASS OUT port is flowing approximately 25 35 sccm Carrier flow within the analyzer is split with a portion of the flow passing through a gas sampling valve the other portion passes through a restrictor tube terminating at the location of the BYPASS OUT port Under normal operating conditions the BYPASS O

Download Pdf Manuals

Related Search

Related Contents

Ramonage Outillage Étanchéité Traitement eau  EMC TEST REPORT - Synocean Technology Co. Ltd  Sony NV-U44/S Marketing Specifications  取扱説明書 - 日立製作所  Gamber-Johnson 7170-0142 mounting kit  Manual - B&B Electronics    DYE-SUBLIMATION - Australian Graphic Supplies  

Copyright © All rights reserved. Failed to retrieve file