User Manual For Digital Keypad Compact Safe
Contents
1. Save You will hear a consistent beeping sound and red light flashes 3 times Repeat steps 1 3 Changing 2nd Personal Pin Code 1 With safe lid open press and release the reset button wait 2 seconds and press and release the reset button again You will hear 2 beeps and indicator light will be consistently green 2 Follow steps 2 3 above INSTALLING THE CABLE Included with the safe is a steel cable that may be attached to any stationary item for increased security The cable hole is located on the side of the safe 1 Locate the stationary item you would like the safe to be attached to and wrap the cable around the stationary item Installing the Cable 2 Thread one end of the cable through the other loop of the cable The loop that was just created in this step should o be wrapped around the stationary item on d 3 Open safe by using the personal pin code or access key 4 Locate the cable slot 5 Place the unused loop of the steel cable with the with the metal stopper portion in the safe through the cable slot 6 Close safe and ensure that the safe is locked 7 Slightly tug on the cable to ensure that the cable is securely attached to the safe Removing the Cable 1 Open safe by using the personal pin codes or access key 2 Lift steel cable out of the cable slot 3 Pull the one end of the cable through the other loop of the cable 4 Store cable in a safe place MOUNTING The safe2. may be mounted to a wall or to the floor The three pre drilled mounting holes are located under the safe and can be exposed by gently removing the rubber pads out of it s place NOTE On Wall Mounting When mounting to a wall be aware of the load bearing to ensure safety of safe and contents Failure to do so could result in the safe falling and damaging property and or people DO NOT mount safe without anchoring to the wall behind the safe When mounting to a wall check the wall or cabinet for structural soundness 1 Check location for concealed items such as wires pipes etc 2 Get the appropriate anchors for the type of floor or wall you will be mounting the safe to wood tile concrete etc 3 Mark the surface to drill holes for the anchors you will be using 4 Drill the appropriate size hole for the anchors you will be using 5 Once mounted test the strength to make sure the safe is securely mounted CARE AND MAINTENANCE If necessary use a damp cloth to clean the safe DO NOT use chemicals or cleaning agents Keep liquids away from the control panel Spills on the control panel will cause damage and possibly electric shock Secure safe in a proper area to prevent it from falling and causing damage or injury For security purposes change the factory default code as soon as possible DO NOT over stuff the contents of the safe it can damage the motor mechanism or the contents DO NOT disassemble the produ
3. S BARSKA User Manual For Digital Keypad Compact Safe PARTS OF THE SAFE Parts of the Safe A Key Entry B Key Pad C Indicator Light D Reset Button E Battery Compartment and Cover F Cable Slot G Mounting Holes located under the safe WARNING Avoid leaving safe door open and unattended it will allow unauthorized individuals to reprogram the safe gaining full access to the safe and the contents OPENING THE SAFE WITH ACCESS KEY 1 Insert access key into key entry turn clockwise to open partially lift lid of safe and remove access key by turning it counter clockwise 2 Open safe by lifting the lid of the safe NOTE Store access keys in a secure place NOT inside of safe When calling for replacement or additional access keys have the access key code number ready The access key code is etched in the key entry and on the access keys BATTERIES 1 Locate the battery compartment and remove battery cover 2 Gently slide battery holder out of the compartment 3 Place 4 AA batteries and pay attention to the polarity of each battery 4 Gently slide battery holder back into place 5 Replace battery cover REPLACING BATTERIES The red indicator light will start flashing and a continuous beeping sound will be heard This indicates that the batteries are low 1 Open safe by using the access key turn clockwise 2 Repeat steps 1 5 of Batteries to replace batteries 3 Close safe and ensu
4. ave You will hear 1 short and 1 long beep and green light flash You will hear the safe unlock Unsuccessful Save You will hear a consistent beeping sound and red light flashes 3 times Repeat steps in Creating Personal Pin Codes 2 With safe lid open enter in the 2nd set of the personal pin code on the key pad See Successful Save and Unsuccessful Save above 3 Close safe and ensure that the safe is locked OPENING SAFE WITH PERSONAL PIN CODES 1 Enter in either of the personal pin codes on the key pad 2 You will hear 1 short and 1 long beep and green light will flash 3 Open safe by lifting the lid of the safe 4 Close safe and ensure that the safe is locked LOCK OUT When the wrong personal pin code is entered 3 times the safe will be in lock out mode Lock out mode will last 30 seconds After 30 seconds try entering your personal pin code again 3 13 See reverse side for more information BC287 S BARSKA User Manual For Digital Keypad Compact Safe CHANGING PERSONAL PIN CODES Open safe by entering either of the personal pin codes or by using the access key Changing 1st Personal Pin Code 1 Press and release the reset button You will hear 1 beep and indicator light will be consistently green 2 Enter in your 3 8 digit personal pin code on the key pad 3 Press and release the reset button Successful Save You will hear 1 short and 1 long beep and green light flash Unsuccessful
5. ct For all repairs and maintenance contact authorized service centers or distributor BARSKA Customer Service DO NOT place emergency keys inside of safe gt BARSKA 1 YEAR LIMITED WARRANTY COMPACT SAFE BARSKA warrants this new safe to be free of original defects in material and or workmanship under normal use for a period of twelve 12 months from the date product is received by purchaser This warranty does not include damage caused by improper installation or maintenance Damage from misuse abuse accident such as dropping normal wear and tear fire flood or acts of nature Damage from service or repairs other than those performed by BARSKA Labor cost and shipping charges for the removal and replacement of defective parts beyond the initial twelve month warranty period All transportation and shipping charges Removing or altering the seal under any circumstances will automatically void the warranty This warranty is limited to original purchaser and is not transferable This warranty applies only to products purchased in the United States Please email info barska com or call 1 888 666 6769 for Return Merchandise Number RMA before any returns The RMA number must appear on the outside of the shipping package Product must be packed carefully and sturdily in its original packaging to prevent damage in transit and returned freight pre paid to BARSKA OPTICS Repair Department 855 Towne Center Drive Pomona CA 91767 P
6. lease include all of the following when returning BARSKA products for service and or replacement 1 Please write your complete details Name Address Telephone E mail address RMA etc 2 Purchase receipt or Proof of Purchase Original Copy 3 A brief explanation of the defect 4 A Check Money Order of 20 00 to cover inspection shipping and handling Please allow 6 8 weeks for delivery BARSKA will examine and test returned product and repair or replace defective part s or units with new part s or a new unit if necessary within the warranty period Purchaser is required to remit 20 00 to BARSKA for return shipping and handling at time product is returned If repair is required after warranty period expiration purchaser will be charged for replacement parts and return shipping BARSKA Optics shall not be liable for any consequential incidental and or contingent damages whatsoever We will not pay shipping insurance or transportation charges from you to us or any import fees duties and or taxes This warranty supersedes all previous BARSKA Optics warranties 2013 BARSKA Pomona CA 91767 USA t 888 666 6769 f 909 445 8169 www barska com Replacement Keys When calling for replacement or additional access keys have the access key code number ready The access key code is etched in the key entry AND on the access keys
7. re that the safe is locked NOTE After replacing the batteries safe retains the last personal pin codes saved CREATING PERSONAL PIN CODES For security purposes change the factory default codes as soon as possible and before placing valuables in the safe NOTE Safe retains only two 3 8 digit pin codes NOTE 1st default pin code is 1234 2nd default pin code is 1234 1st Personal Pin Code 1 With safe lid open press and release the reset button You will hear 1 beep and indicator light will be consistently green 2 Enter in your 3 8 digit personal pin code on the key pad and press and release the reset button Successful Save You will hear 1 short and 1 long beep and green light flash Unsuccessful Save You will hear a consistent beeping sound and red light flashes 3 times Repeat steps 1 3 2013 BARSKA Pomona CA 91767 USA t 888 666 6769 f 909 445 8169 www barska com 2nd Personal Pin Code For security purposes you must change the 2nd pin code set 1 With safe lid open press and release the reset button wait 2 seconds and press and release the reset button again You will hear 2 beeps and indicator light will be consistently green 2 Follow step 2 in 1st Personal Pin Code NOTE Be sure to write down these codes immediately and store in a secure place TESTING THE PERSONAL PIN CODES 1 With safe lid open enter in 1st set of the personal pin code on the key pad Successful S
Download Pdf Manuals
Related Search