10/100/1000Base-T to Dual 1000Base
Contents
1. seeeseeeeeeeeeneee 15 1 Introduction 1 1 Check List Check the contents of your package for following parts 1205 x 1 5V 2A AC DC Power Adapter x 1 User s Manual x 1 GT 1205A is with two vacant SFP module slot The 1000Base X SFP module is not bundled with in the package 1 2 Introduction To GT 1205A Thank you for choosing the 10 100 1000Base T to Dual 1000Base X SFP Media Converter The GT 1205A is a 3 Port Media Converter which supports conversion between 10 100 1000Base T 1000Base X network Different with the other one port channel media converter the Media Converter is designed for critical networks that require fiber or copper link such as ISP telecom hospital banking and enterprise PLANET 3 Port Gigabit Media converter is shown as following With the 3 Port switch mode they work in high performance Store and Forward mechanism also can prevent packet loss with IEEE 802 3x Flow Control Full Duplex and Back Pressure Half Duplex With 1000Base X SFP ports the GT 1205A is with high reliability and flexibility to extend the distance up to 550m 10Km 20Km or longer The Media Converter can be used as a stand alone unit or as a slide in module to the PLANET Media Converter Chassis MC 700 and MC 1500 series it could be hot swappable in MC Chassis 1 3 Key Features W Standard Complies with IEEE 802 3 IEEE 802 3u IEEE 802 3ab 10 100 1000Ba2. 7 White Brown 8 Brown Cross Over Cable 12345678 SIDE1 ell 12345678 SIDE2 SIDE 1 1 White Orange 2 Orange 3 White Green 4 Blue 5 White Blue 6 Green 7 White Brown 8 Brown SIDE 2 1 White Orange 2 Orange 3 White Green 4 Blue 5 White Blue 6 Green 7 White Brown 8 Brown SIDE 2 1 White Green 5 White Blue 6 Orange 7 White Brown 8 Brown Figure A 1 Straight Through and Crossover Cable Please make sure your connected cables are with same pin assignment and color as above picture before deploying the cables into your network A 3 Fiber Optical Cable Connection Parameter The wiring details are as below W Fiber Optical patch Cables Diameter Modal Max Standard Fiber micron Bandwidth Distance MHz km meters 62 5 100 220 62 5 200 275 1000Base SX Multi mode 50 400 500 50 500 550 62 5 5 550 Multi mode 150 4 1000Base LX 50 5 Single mode 9 N A 5000 13 H The IEEE 1000Base LX standard supports up to 5000 meters however with various SFP modules the actual link distance may vary Please check appendix for the available modules A 4 Power Information The power jack of the Gigabit Media Converter is with 2 5mm in the central post and required 5V DC power input It will conform to the bundled AC DC adapter and PLANET s Media Chassis If you have issue to make the p
3. IEEE 802 3 10Base T IEEE 802 3u 100Base TX Standards IEEE 802 3ab 1000Base T IEEE 802 3z 1000Base SX LX IEEE 802 3x Flow Control 2 2 LED Indicator The LED indicators give you instant feedback on status of the converter 7 1 E System LED Color Function PWR Green Lit Power on W GT 1205A 10 100 1000Base T Port LED Color Function Lit Indicate that the fiber optical port is link up Blink Indicate that the converter is actively sending 1 Green or receiving data over that port Indicate that the fiber optical port is link Off down Lit Indicate that the fiber optical port is link up Blink Indicate that the converter is actively sending 2 Green or receiving data over that port Indicate that the fiber optical port is link Off down Lit Indicate that the copper port is link up LNK Indicate that the converter is actively sending ACT Orange Blink or receiving data over that port Off Indicate that the copper port is link down Indicate that the copper port is operating at Lit 1000Mbps 1000 Green ps Indicate that the copper port is link down 10 100Mbps 3 Installation 3 1 Product Outlook W Front Panel 10 100 1000Base T to Dual 1000Base X SFP Port 1 1000Base X SFP slot Port 2 1000Base X SFP slot Port 3 10 100 1000Base T copper connector Rear Panel
4. 5v Dc One DC jack for DC 5V 2A power input oco 3 2 Stand alone Installation GT 1205A is with high reliability and flexibility to extend the distance up to 550m and 10 15 20 30 40 50 60 70 120km It depends on the 1000Base SX LX SFP transceiver modules The SFP transceiver is hot pluggable and hot swappable You can plug in and out the transceiver to from any SFP port without having to power down the converter To install a GT 1205A stand alone on a desktop or shelf simply complete the following steps Step 1 Turn off the power of the device station in a network to which the GT 1205A will be attached Step 2 Ensure that there is no activity in the network Step 3 Slot in the 1000Base X SFP Make sure both side of the SFP transceiver are with the same media type for example 1000Base SX 550m multi mode to 1000Base SX 550m multi mode 1000Bas LX 10km single mode to 1000Base LX 10km single mode 9 1 LC Fiber 1000Base X SFP a M Pp A T 2 1000 1000Base X 5V DC power LC Fiber Figure 3 1 GT 1205A Media Converter Stand Alone Installation Step 4 Step 5 Step 6 Step 7 1 10 Connect the fiber cable Attach the duplex LC connector on the network cable into the SFP transceiver Attach fiber cable from the GT 1205A to the fiber network TX RX must be paired at both ends Connect the 5V DC power adapter to the GT 1205A and verify that the
5. Address 10F No 96 Minquan Rd Xindian Dist New Taipei City 231 Taiwan R O C Person responsible for making this declaration Name Surname Kent Kang Position Title Product Manager pen Taiwan 30 Sep 2011 Place Date Legal Signature PLANET TECHNOLOGY CORPORATION e mail sales planet com tw _http www planet com tw 10F No 96 Minquan Rd Xindian Dist New Taipei City Taiwan R O C Tel 886 2 2219 9518 Fax 886 2 2219 9528
6. Power LED lights up Turn on the power of the device station the LINK LED should light when all cables are well attached 1 It is recommends using PLANET MGB series SFP modules for the converter If you insert a SFP trans ceiver that is not supported the converter will not recognize it Please check appendix or go visit our WEB site for details specification information http www planet com tw 2 To prevent from optic acceptor malfunction check the both wires transmitter before power on the con verter 3 To remove the SFP module please remove the fiber connectors in advanced and push the belt or letch of the module Pull out the module with violent may damage the module and the converter 3 3 Chassis Installation And Rack Mounting To install the media converter in a 10 inch or 19 inch with standard rack follow the steps described below Step 1 Find an available slot from your PLANET MC Chassis Step 2 Follow Figure 3 2 carefully slide in the converter fully and firmly fitted to the Figure 3 2 Insert GT 1205A slot of the chassis Media Converter into an The Power LED of the available slot converter will turns ON 1 Never push the converter into the slot with violent it could damage the chassis 2 The Media Converter Chassis supports hot swap there is no need to turn off the whole chassis before slide in the new converter 3 4 Din Rail Installation The GT 1205A also suppor
7. 10 100 1000Base T to Dual 1000 SFP Media Converter GT 1205A User s Manual Trademarks Copyright PLANET Technology Corp 2011 Contents subject to which revision without prior notice PLANET is a registered trademark of PLANET Technology Corp All other trademarks belong to their respective owners Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications and makes no warranty and representation either implied or expressed with respect to the quality performance merchantability or fitness for a particular purpose PLANET has made every effort to ensure that this User s Manual is accurate PLANET disclaims liability for any inaccuracies or omissions that may have occurred Information in this User s Manual is subject to change without notice and does not represent a commitment on the part of PLANET PLANET assumes no responsibility for any inaccuracies that may be contained in this User s Manual PLANET makes no commitment to update or keep current the information in this User s Manual and reserves the right to make improvements to this User s Manual and or to the products described in this User s Manual at any time without notice If you find information in this manual that is incorrect misleading or incomplete we would appreciate your comments and suggestions FCC Warning This device has been tested and found to comply with the limits for a
8. Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the Instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at whose own expense CE Mark Warning This is a Class B product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Energy Saving Note of the Device This power required device does not support Standby mode operation For energy saving please remove the DC plug to discon nect the device from the power circuit Without removing the DC plug or switch off the device the device will still consume power from the power source In the view of Saving the Energy and reduce the unnecessary power consuming it is strongly suggested to power off or to remove the DC plug for the device if this device is not intended to be active WEEE Warning To avoid the potential effects on the environment and XI human health as a result of the presence of hazardous substances in electrical and electronic equipment end
9. ower connection please contact with your local sales dealer Please keep the AC DC adapter as spare parts when your Media Converter is installed to a Media Chassis 2 5mm gt Receptacle 2 5mm 5V for each slot oco DC receptacle is 2 5mm wide that conforms to and matches the Media Converter 2 5mm DC jack s central post Do not install any improper unit model of the Media Converter A 14 5 Available Modules The following list the available Modules for GT 1205A MGB GT SFP Port 1000Base T mini GBIC module MGB SX SFP Port 1000Base SX mini GBIC module 550meters MGB LX SFP Port 1000Base LX mini GBIC module 10km MGB L30 SFP Port 1000Base LX mini GBIC module 30km MGB L50 SFP Port 1000Base LX mini GBIC module 50km MGB L70 SFP Port 1000Base LX mini GBIC module 70km MGB L120 SFP Port 1000Base LX mini GBIC module 120km SFP Port 1000Base LX mini GBIC module MGB LA10 c wDM TX 1310nm SM 10km SFP Port 1000Base LX mini GBIC module MGB LB10 c wh TX 1550nm SM 10km SFP Port 1000Base LX mini GBIC module MGB LA20 TX 1310nm SM 20km SFP Port 1000Base LX mini GBIC module MGB LB20 c wom TX 1550nm SM 20km SFP Port 1000Base LX mini GBIC module MGB LA40 c WEM TX 1310nm SM 40km SFP Port 1000Base LX mini GBIC module MGB LB40 i e WDM TX 1550nm SM 40km SFP Port 1000Base SX mini GBIC mod
10. se T IEEE 802 3z 1000Base SX LX IEEE 802 3x Full Duplex Flow Control Back Pressure in Half Duplex eliminate packets loss Interface Dual 1000Base SX LX SFP Fiber optic One 10 100 1000Base T Copper Auto Negotiation for 10 100Base TX Half Duplex or 10 100 1000Base T Full Duplex Auto MDI MDI X W Mechanical 5V 2A DC power supply LED indicators for easy network diagnose Co work with PLANET MC family Media Chassis MC 700 1500 1500R 1500R48 2 Product Specification 2 1 Functional Specifications Model GT 1205A Copper 1 x 10 100 1000Base T port Fiber 2 x 1000Base X SFP interfaces Optic Interface SFP 10Base T 2 UTP 3 4 5 up to 100 meter 100Base TX 2 Pair UTP CAT 5 5e up to 100 meter 1000Base T 4 Pair UTP CAT 5e 6 up to 100 meter 50 125 or 62 5 125 multi mode fiber cable up to 220 amp 550 meters Fiber optic 9 125um single mode cable cable provide long distance for 10 15 20 30 40 50 60 70 120km or longer vary on SFP module Twisted pair Cable Switch Processing GR ENTIS Store and Forward Switching Fabric 6Gbps non blocking System One Power LED LED indicator TP Port One Speed One LNK ACT Fiber Port Two LNK ACT Dimension W x D x H 94 x 70 x 26 mm Weight 191g device only Power Requirement 5V DC 2A max Power Consumption 5 4Watts 18 5 BTU per hour max
11. ts din rail installation the option kit RKE DIN can help to mount the converter to the Rail system please follow the steps below Step 1 Use the bundled screw to fix the RKE DIN to the converter Step 2 Hook the converter to the DIN Rail You must use the screws supplied with the RKE DIN Damage caused to the parts by using incorrect screws would invalidate your warranty 11 41 4 Appendix A A 1 Device s RJ 45 Pin Assignments m 1000Mbps 1000Base T RJ 45 Connector pin assignment Contact MDI MDI X Contact MDI MDI X 1 BI_DA 5 BI DC BI DD 2 BI DA BI DB 6 BI DB BI DA 3 BI BI_DA 7 BI_DD BI_DC 4 BI_DC BI_DD 8 BI_DD BI_DC m 10 100Mbps 10 100Base TX RJ 45 Connector pin assignment Contact MDI Media Dependant MDI X Media Dependant Interface Interface Cross 1 Tx transmit Rx receive 2 Tx transmit Rx receive 3 Rx receive Tx transmit 4 5 Not used 6 Rx receive Tx transmit 7 8 Not used A 2 RJ 45 Cable Pin Assignment Ce A 12 The standard RJ 45 receptacle connector There are 8 wires on a standard UTP STP cable and each wire is color coded The following shows the pin allocation and color of straight cable and crossover cable connection SIDE 1 SIDE 1 1 White Orange 2 Orange 3 White Green 4 Blue 5 White Blue SIDE2 6 Green
12. ule MGB TSX 550meters 40 75 C SFP Port 1000Base LX mini GBIC module 10km MGB TLX 40 75 C SFP Port 1000Base LX mini GBIC module 30km MGB TL30 40 75 C SFP Port 1000Base LX mini GBIC module 70km MGB TL70 40 75 C 15 H GQ PLANET Networking amp Communication EC Declaration of Conformity For the following equipment Type of Product 10 100 1000Base T to Dual 1000Base X SFP Media Converter 1 TP 2 SFP Model Number GT 1205A Produced by Manufacturer s Name Planet Technology Corp Manufacturer s Address 10 No 96 Minquan Rd Xindian Dist New Taipei City 231 Taiwan is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive on 2004 108 EC For the evaluation regarding the EMC the following standards were applied EN 55022 CLASS A 2006 A1 2007 EN 61000 3 2 2006 A2 2009 EN 61000 3 3 2008 EN 55024 1998 A1 2001 A2 2003 IEC 61000 4 2 2008 IEC 61000 4 3 2008 IEC 61000 4 4 2004 IEC 61000 4 5 2005 IEC 61000 4 6 2008 IEC 61000 4 8 2009 IEC 61000 4 11 2004 Responsible for marking this declaration if the Manufacturer Authorized representative established within the EU Authorized representative established within the EU if applicable Company Name Planet Technology Corp Company
13. users of electrical and electronic equipment should understand the meaning of the crossed out wheeled bin symbol Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately Revision PLANET Gigabit Ethernet Redundant Media Converter User s Manual FOR MODEL GT 1205A Revision 1 0 Augest 2011 Part No 2350 AA4530 000 Table of Contents 9 euo 5 1 1 CHECK BISE crece eap IS S ER ep ede etu seu 5 1 2 Introduction GT 1205A eee eise ono eterne onere net 5 1 3 Key Features uiscera sene per ta VK EE EN CREER EE 6 gt Product Specification du 6 2 1 Functional Specifications iisisti 6 2 2 WED Indicator iui esee pa hne PR sn thu i eph E pie Ua 7 o AMSA ACO M 8 3 1 Product OUtlook 2 8 3 2 Stand alone Installation eniro pio 9 3 3 Chassis Installation And Rack Mounting 11 3 4 Dim Rail Installation ruo epo ce onore 11 Nera E 12 1 Device s RJ 45 Pin Assignments 12 A 2 RJ 45 Cable Pin Assignment sees 12 Fiber Optical Cable Connection Parameter 13 4 Power Information uucn ido enaa 14 A 5 Available Modules
Download Pdf Manuals
Related Search