BCS25 Manual EN/ rev 05-23-06
Contents
1. lt nO lt nO G NO jc Els eg eg ik Me ee ee oz Az es o2 ef Me J8 J8 J8 Fig 6 Fig 7 Fig 8 Jumpers J8 and J9 select the type of operation It is possible to choose between faderstart figure 6 buttonstart figure 7 or the fader switch combinaton figure 8 On air channels The BCS25 has two on air groups This makes it possible to drive an indicator when the microphones are opened The output will be activated when one or more channels that belong to the on air group are opened With jumper J12 a channel is configured as on air 1 or on air 2 channel When a channel is configured as on air 1 the studio output will be muted when the channel is active The on air 1 output on the master also will be activated A channel configured as on air 2 will not mute the studio but only activate the on air 2 output on the master EIN Dateq BCS25 manual BCS26 E telephone input module Master cue Each channel can activate the master cue function When the cue button is pressed the master module automatically selects the CUE bus as input This function can be activated with J10 J10 J10 Om EN CUE OFF CUE OFF DJ Mode When jumper J11 is set to DJ the control room will be muted when the channel2. 1351 JG ALMERE The Netherlands Niederlande Pays Bas
3. A GEBRUIKSAANWIJZING gt USER MANUAL ES GEBRAUCHSANWEISUNG p MODE D EMPLOI DJAJTJEJQ Gade tect gus EN Dateq BCS25 Manual Safety instructions EN Safety instructions 1 2 3 4 5 10 11 12 13 14 15 16 All safety instructions warnings and operating instructions must be read first All warnings on the equipment must be heeded The operating instructions must be followed Keep the operating instructions for future reference The equipment may never be used in the immediate vicinity of water make sure that water and damp cannot get into the equipment The equipment may only be installed or fitted in accordance with the manufacturers recommendations The equipment must be installed or fitted such that good ventilation is not obstructed in any Way The equipment may never be installed in the immediate vicinity of sources of heat such as parts of heating units boilers and other equipment which generates heat including amplifiers Connect the equipment to a power supply of the correct voltage using only the cables recommended by the manufacturer as specified in the operating instructions and or shown on the connection side of the equipment The equipment may only be connected to a legally approved earthed mains power supply The power cable or power cord must be positioned such that it cannot be walked on in normal use and objects which might damage the cable
4. DATEQ beh lt sich das Recht vor Garantieleistungen abzulehnen wenn nach dem Ersterwerb des Ger tes durch den Verbraucher oder den Handler diese Angaben oder das Seriennummer entfernt oder ge ndert worden sind 2 Diese Garantie deckt keinen der folgenden Punkte a regelm ftige Inspektionen Wartung bzw Reparatur oder Austausch von Teilen bedingt duch normalen Verschlei b Transport Fahrtkosten und risiken die unmittelbar oder mittelbar mit ser Ger tegarantie zusammenhangen c Sch den an diesem Ger t die verursacht worden sind durch Mi amp brach und Fehlgebrauch insbesondere Gebrauch dieses Ger tes f r andere als seinen normalen Zweck bzw unter Nichtbeachtung der DATEQ Bedienungs und Wartungsanleitungen und den Anschlu oder Gebrauch dieses Ger tes in einer den in dem Land in dem das Ger t bebraucht wird geltenden technischen oder sicherheitstechnischen Anforderungen nicht entsprechenden Weise Reparaturen duch nicht autoi rte Werkstatten Unfalle h here Gewalt oder andere von DATEQ nicht zu verantwordende Ursachen insbesondere Blitzschlag Wasser Feuer St rungen der ffentlichen Ordnung und unzureichende Bel ftung CONDITIONS DE GARANTIE DATEQ garantit que ce produit est exempt de d fautde mati re et de fabrication existantlors de l acquisition originale parle client pour un d lai d un an Si ce produit s av re d fectueux pendant la p riode de garantie en raison de mati re ou de fabricati
5. POWER BCS25 control room 2x TRS Jack 3p BCS25 On air 2x TRS Jack 3p Pin Function Type Pin Function Type BCS25 Program 2x XLR 3p male BCS25 Program 2x TRS Jack 3p Pin Function Type Pin Function Type 22 Dateq BCS25 manual BCS27 Master module Talkback functions AUTOGAIN The talkback input has an autogain function The amplification can be adjusted with JP2 When low is selected the autogain range is 10dB When high is selected the range is 30dB When jumper JP2 isn t placed an external microphone source can be connected to the EXT MIC connector O Dateq BCS25 manual Technical specifications INPUTS AUX1 AUX2 HYBRID TELOS HYBRID electronically balanced 300 Ohm nominal 54 16dBm 127dB 46 12dB electronically balanced 20 kOhm nominal 12 20dBm 0dBm nominal lt 80dB 46 12dB unbalanced 24 kOhm nominal 18 20dBm 6dBm nominal lt 80dB 46 12dB pre fader variable pre or post fader fixed 15 6dB externally adjustable internally adjustable Triple Dynamical Mix Minus 30dB 300 3kHz electronically balanced 20 kOhm balanced OdBm 600 Ohm 80dB MASTER MONITOR INPUTS OUTPUTS unbalanced 12 kOhm nominal 14 6dB pre trimmer unbalanced 22 kOhm nominal 0dB electronically balanced and unbalanc
6. is activated all CUE functions will be turned off and the master module will select program or audition depending on the routing switches J11 DJ J11 DJ o ON OFF OFF Cleanfeeds Auxiliary bus The BCS26 E module contains 2 mono bus outputs which can be used to create a return signal to for example an ISDN codec The signal at these busses is post fader At each individual channel of the console can be selected if they belong to one or both of the cleanfeeds by setting jumpers J4 and J5 in the right position The first example shows a channel that doesn t belong to a cleanfeed The second example belongs to cleanfeed one and not to cleanfeed two F 2 3 2 F HA o 5 lo ON ON The BCS25 had two auxiliary busses The first bus is always pre fader the second bus can be configured to be pre or post fader This is done with J2 ad J3 AUX2 AUX2 515 513 EN Dateq BCS25 manual BCS26 E telephone input module KE Internal or external hybrid The BCS26 E module handles incoming telephone calls over the built in hybrid but is also able to remote control an external digital hybrid or talk show system With jumper J6 J7 and J1 it s possible to select the type of operation Jumper J6 and J7 are used to switch between the intern
7. 9 AUdoGND AGND 22 Line2Audioleft These inputs are available when the optional balanced input module or the RIAA correction amplifier are inserted The line 2 unbalanced inputs are to be discarded When a RIAA correction amplifier is mounted use pins 6 and 18 for the signal Pins 5 and 17 are internally connected to the ground 8 Dateq BCS25 manual BCS25 E dual line microphone input module Phantom power Non dynamically microphones usually need an external power supply for its built in pre amplifier If this power has to be supplied by the BCS25 place jumper J1 in the ON position 48Vdc will be supplied to both signal wires related to the cables shielding Jumper J1 is situated on the left side of the bussconnector The factory default setting for this jumper is OFF See picture below ON OFF ON OFF 48V HN O 48V O JI Dynamically microphones don t need a phantom power supply When the correct cables are used it will not damage the microphone when the phantom power supply is turned on So it is not really dangerous to turn the phantom power on for all types of microphones Faderstart buttonstart The BCS25 E module is able to remote start connected equipment by faderstart buttonstart or a combination of these two options By changing jumpers you easily select one of these settings The jumpers for remote start settings can be found at
8. CUE button input 50 kOhm normally open line 1 only Remote outputs solid state driver 15Vdc 10 mA ON AIR lamp output solid state driver 15Vdc 10 mA SUPPLY Supply voltage 90 to 260 Vac 50 60 Hz 30 Watt GENERAL Dimensions 445 x 395 x 110 mm W x H x D Weight 7 9 kg nett VERKLARING VAN OVEREENSTEMMING acc to art 10 1 EMC directive 89 336 EEC Wij DATEQ Audio Technologies b v de Paal 37 1351 JG ALMERE Nederland verklaren uitsluitend op onze verantwoordelijkheid dat dit produkt Type BCS25 Serienummers 76 XXXX waarop deze verklaring betrekking heeft in overeenstemming is met de volgende geharmoniseerde Europese normen EN 50081 1 en EN 50082 1 Volgens de bepalingen van de EMC richtlijn 89 336 EEG gewijzigd door de richtliin 91 263 EEG 92 31 EEG en 93 68 EEG EN 60065 Volgens de bepalingen van IEC 65 1985 A1 1987 A2 1989 A3 1992 mod Ratificatie 1993 07 06 Almere 5 februari 1999 J H Kloppenburg Directeur stempel handtekening ando De Paal 3 1351 JG Almere tel 036 5472222 fax 036 5317776 tel 036 5472222 fax 036 5317776 DECLARATION OF CONFORMITY acc to art 10 1 EMC directive 89 336 EEC We DATEQ Audio Technologies B V de Paal 37 1351 JG ALMERE THE NETHERLANDS hereby declare exclusively to our responsibility that this product Type BCS25 Serialnrs 76 XXXX to which this dec
9. UE function is activated With an internal jumper the master cue function can be dis activated On off switch It is possible to select faderstart buttonstart or a combination of both with an internal jumper The yellow LED is lighted when the channel is on 100mm long volume control Depending on a jumper setting the signal on the AUX2 bus is pre or post fader Dateq BCS25 manual BCS26 E telephone input module BCS26 E connector board DB25 F connector All connections are made on this connector The function of the various pins can be found in the table Telephone input BCS 26 BCS26 E Audio and Control Input Output Sub D 25 pins female Pin Function Type ER HA el Line A telephone line I Line B telephone line i AAA Ge m EU Out 3 C 5 Off hook On 15V 10 mA Out Ring 15V 10 mA AE Remote hybrid out Optocoupler output 7 Remote hybrid on Optocoupler output 2 0 In Co 4 5 6 7 8 9 1 3 1 2 5 HE EE GE 6 1 EN Dateq BCS25 manual BCS26 E telephone input module KEN Faderstart buttonstart The BCS26 E module is able to remote start connected equipment by faderstart buttonstart or a combination of these two options By changing jumpers you easily select one of these settings The jumpers for remote start settings can be found at the main PCB above the bussconnector jumper J8 and J9 see drawing
10. UE bus as input This function can be activated with J10 J10 J10 Om EN CUE OFF CUE OFF DJ Mode In a self support configuration the control room has to be muted when the microphone is opened The announcer has to use a headphone so that acoustical feedback is impossible When jumper J11 is set to DJ the control room will be muted when the channel is activated all CUE functions will be turned off and the master module will select program or audition depending on the routing switches J11 DJ J11 DJ OEA ON OFF OFF Cleanfeeds Auxiliary bus The BCS25 E module contains 2 mono bus outputs which can be used to create a return signal to for example an ISDN codec The signal at these busses is post fader At each individual channel of the console can be selected if they belong to one or both of the cleanfeeds by setting jumpers J4 J7 in the right position In the example below the signal of this channel is send to cleanfeed bus 1 only J5 mE 2 OFF CUE OFF AIR Beside the cleanfeeds the BCS25 E module has 2 auxiliary busses The first auxiliary is always pre fader Auxiliary 2 can be switched between pre and postfader by jumper J2 and J3 AUX2 AUX2 c c 515 POST POST Dateq BCS25 manual BCS26 E
11. ain PCB above the bussconnector in the middle selects between a continue or pulse signal at the remote output PLS CON mm O PLS CON Fig 4 Fig 5 In the pulse position the remote outputs will generate a pulse of 100msec When the continues mode is selected the on output will provide a high level signal when the channel is switched on and a low level signal as soon as the channel is switched off The remote outputs only work when line input 1 is selected On air channels The BCS25 has two on air groups This makes it possible to drive an indicator to indicate that the microphones are opened The output will be activated when one or more channels that belong to the on air group are opened With jumper J12 a channel is configured as on air 1 or on air 2 channel When a channel is configured as on air 1 the studio output will be muted when the channel is active The on air 1 output on the master also will be activated A channel configured as on air 2 will not mute the studio but only activate the on air 2 output on the master N N N O mm m 211 OFF 211 OFF 2_ 1 or ON AR ON AR ON AR Dateq BCS25 manual BCS25 E dual line microphone input module Master cue Each channel can activate the master cue function When the cue button is pressed the master module automatically selects the C
12. al or external hybrid J1 switches the bandpass filter on or off When a hybrid with built in band pass filter is connected J1 should be placed in the OFF position The drawing below only shows J1 and J7 J6 can be found above the transformer see the autogain drawing at the bottom of this page er 7 Fig 9 Internal hybrid bandpass filter on J7 Fig 10 External hybrid bandpass filter off Autogain The BCS26 E is equipped with a special feature that reduces the signal from the hybrid by 6dB when audio is sent from the mixer to the hybrid This means that the caller is dimmed by 6dB when the announcer in the studio speaks This feature improves the side tone reduction with 6dB so creating the best possible speech intelligibility The consequence of this auto gain feature is that when the caller and announcer are talking at the same time double talk the announcer in the studio will slightly drown the voice of the caller This function can be disabled with jumper J13 In the first example the autogain function is enabled O GAN O Hi J13 J13 EIN Dateq BCS25 manual BCS26 E telephone input module TDM The hybrid automatically gets the correct N 1 return from the CUE PGM or AUD bus This
13. ed 6dBm 600 Ohm OdBm 600 Ohm unbalanced variable OdBm 600 Ohm unbalanced variable OdBm 600 Ohm electronically balanced variable OdBm 600 Ohm Technical specifications 24 Dateq BCS25 manual Technical specifications ANN GUEST1 GUEST2 stereo headphone variable E 2x 0 5 W 4 Ohm STUDIO unbalanced variable ene OdBm 600 Ohm CLEANFEED1 2 unbalanced level iue OdBm 600 Ohm xr etat 6dB octave point 80 Hz fixed LINE ERES 6dB octave 3dB point 10 Hz fixed EQUALIZER E version only MIC LINE HIGH EE 12dB 12 kHz shelving MID oet 12dB 1 3 kHz bell 12dB 60 Hz shelving TEL HGH RE 12dB 3 5 kHz shelving LOW 12dB 600 Hz shelving GENERAL Frequency response Mic to master 80 Hz 30 kHz 0 0 5dB rest to master 20 Hz 30 kHz 0 0 5dB THD IM 0 05 nominal Crosstalk L lt gt R lt 73dB 1 kHz Crosstalk 1 lt gt 2 80dB 1 kHz NOISO3 lt 100dB inputs OFF 80dB inputs ON Overload indication 6dB below clip level Clip level 20dB METER type range Peak Hold 40 6dB barlength 40 LEDs INPUT CONTROL I O ON Lamp output 15Vdc 100mA line 1 only
14. iary 1 and auxiliary 2 can be found AIR SP1 SP2 9 pins female sub D connector to which the air spare 1 and spare 2 signals can be connected The level of the air input can be adjusted with two trimmers one for the left signal level and one for the right signal level MCA 100 Connector for Dateq s MCA 100 headphone amplifiers so that more headphones for announcers and guests can be connected each with their own volume control and cough speak button CR R 8 CR L Balanced control room outputs OA On air outputs On air indicators such as Dateq s OA1 can be connected PGM XLR 3 male Balanced program outputs Jack Two unbalanced stereo program outputs 20 Dateq BCS25 manual BCS27 Master module BCS25 GST ANN STD CF1 CF2 DB15 F connector Pin Function Type 9 AudoGND 1 1 1 OAND 6 Studiolet Out 8 Clearfeed1 Out _ BCS25 AUD AUX1 AUX2 DB9 F connector Pin Function Type 6 AudoGND AGN 8 ___ _ _ 9 ____ AGND BCS25 AIR SP1 SP2 DB9 F connector Pin Function Type 6 AudioGND AGN 8 Spare2left i 9 AudoGND 1 1 01 O AGND EN Dateq BCS25 manual BCS27 Master module BCS25 100 DIN 6p 270 female Pin __ Function Type Stereo 1 Left default Announcer Left Stereo 1 Right default Announcer Right 6 12V DC do not connect when an external supply is being used
15. is the so called Triple Dynamic Mix Minus system shortened to TDM Since the BCS26 generates the N 1 signal itself separate cleanfeeds are not necessary The number of BCS26 modules which can be used at the same time is therefore theoretically unlimited In practice the number of telephone lines which can be used at the same time is limited by the quality of the telephone hybrids being used If AUD is selected as well as PGM the return from the PGM bus has priority over the return from the AUD bus CUE has the highest priority when the channel is off As soon as CUE is selected on a BCS26 module the hybrid gets the return from the CUE bus Dateq BCS25 manual BCS27 Master module BCS27 Master module The BCS27 master module has a microprocessor that handles the audio matrix This matrix routes the audio outputs The second function of the microprocessor is controlling the VU meter TB MIC Connector for the Talk Back microphone Meter Source selector for the VU meter The meter switches between PGM of control room AUX1 Volume control for the auxiliary 1 output AUX2 Volume control for the auxiliary 2 output AUD Volume control for the audition output Air Cue Selection of the signal on the control room and the CUE output The active selection is indicated with a yellow LED under the button Mute The LED lights up RED if the control room output is automatically switched off CR Volume control for the control room out
16. l with or without equalizer the build in power supply and an extensive mastersection with LED PPM s Input modules The universal BCS25 E input channel features 3 inputs line 1 line 2 and mic a gaincontrol a 3 band equaliser option without and a balance control The input signal can be routed to two stereo mix busses with the audition and program select buttons This enables the engineer to set up two different output mixes or to use the console for two different jobs running simultaneously The auxiliary 1 is pre fader and has a volumecontrol on the module The auxiliary 2 bus sends the signal directly to the master section the signal may be selected pre or post fader The cue button enables pre fade listening of the input source A fader button start feature is standard fader or button function is set by an internal jumper The 100 mm fader is not in the audio signal path but only controls the VCA this prevents any signal distortion and increases reliability Telephone hybrid There is also a special telephone channel available with integrated analogue telephone hybrid This channel can also be used as a remote for an external hybrid The ON OFF buttons can be used for the remote control for the external hybrid The BCS26 E is equipped with an intelligent electronic circuit to generate a mix minus signal Dateq s unique TDM This makes it possible to have more than one hybrid in the mixer BCS27 Master module The master sec
17. laration applies is in accordance with the following harmonized European norms EN 50081 1 and EN 50082 1 According to the regulations of the EMC directive 89 336 EEG amended by directive 91 263 EEG 92 31 EEG and 93 68 EEG EN 60065 According to the regulations of IEC 65 1985 A1 1987 A2 1989 A3 1992 mod Ratification 1993 07 06 Almere Februari 5 2001 J H Kloppenburg managing director stamp signature DJAITIEJQ De Paal 37 1361 JG Almere DIAITIEIQ GARANTIE BEPALINGEN DATEQ garandeert dat dit produkt vrij is van defecten in materialen en of contructie gedurende 12 maanden na aankoop Indien gedurende deze periode het produkt defecten vertoont tengevolge van ondeugdelijke materialen en of constructie zal DATEQ zonder berekening van kosten voor arbeidsloon of onderdelen het produkt repareren volgens de voorwaarden zoals hierna uiteen zijn gezet 1 Garantie wordt verleend uitsluitend op vertoon van de garantiekaart tezamen met de originele door de dealer afgegeven factuur kassabon DATEQ behoudt zich het recht voor garantie af te wijzen indien de hierboven genoemde gegevens of het serienummer van het produkt zijn verwijderd of veranderd na de oorspronkelijke aankoop 2 Deze garantie dekt niet a periodieke controles onderhoud en reparatie of vervanging van onderdelen door normale slijtage b kosten en risico van transport alsmede voorrijkosten direct of indirect verband houdende met de garantie van dit
18. lume pre setting Range 46dB to 12dB High tone control BCS25E only Shelving 12dB 12kHz Mid Mid tone control BCS25E only Bell curve 12dB 1 3kHz Low Low tone control BCS25E only Shelving 12dB 60Hz E AUD PGM Bus routing switches When a switch is pushed yellow LED UN ms is lighted the signal will be routed to the selected output AUX Volume control for AUX1 level The AUX1 bus is pre fader BAL Balance control The signal is placed at the desired position in the stereo image CUE Pre fader listening The LED lights up green when the CUE function is activated With an internal jumper the master cue function can be dis activated ON On off switch It is possible to select faderstart buttonstart or a combination of both with an internal jumper The yellow LED is lighted when the channel is on Fader 100mm long volume control Depending on a jumper setting the signal on the AUX2 bus is pre or post fader EN Dateq BCS25 manual BCS25 E dual line microphone input module BCS25 E connector board DB25 F connector All connections are made on this connector The function of the various pins can be found in the table Universal input BCS 25 BCS25 E Audio and Control Input Output Sub D 25 pins female Pin Function Type 2 jExemalCUE Lne1 h 5 Line2Audioright In 6 Line2Audioright h 8 Microphone Audio h
19. n channel for example to a second studio This function can be enabled by simultaneously pressing the AIR and talk to guest buttons The guest output will be muted The only signal on the guest output is the talk signal By default this function is disabled It is possible to enable or disable the talk to cleanfeed function This is done by simultaneously pressing the AIR and talk to cue buttons When the talk to cue button is pressed the talkback signal will be routed to the cue and the cleanfeed buss By default this function is disabled The DJ mode has three settings These settings can be selected by pressing the AIR and PGM simultaneously 1 The master automatically switches to PGM or AUD depending on the selected buss on the microphone input 2 The master automatically switches to AIR 3 DJ mode disabled The source will not change EN Dateq BCS25 manual BCS27 Master module BCS27 connector board The BCS27 connector board has the connectors for the in and outputs There are three spares for extra jack connectors AUD AIR AUX1 SP1 AUX2 SP2 9t MEE MCA 100 GST ANN STD CF1 CF2 15 pins female sub D connector with the signals for the guest announcer studio and two cleanfeeds The guest and announcer outputs have headphones drivers The studio and cleanfeed outputs are at line level AUD AUX1 AUX2 9 pins female sub D connector On this connector the outputs for the audition auxil
20. on incorrecte DATEQ prendra en charge le produit ou d faut DATEQ sous les conditions expos es ci apr s 1 La garantie sera seulement assur e si la facture origiale et la carte de garanti remises au consommateur par le distributeur sont pr sent es DATEQ se r serve le droit de refuser sa garantie si tout ou partie de ces mentions ou le numero de s rie de l appareil a t ou modifi apr s l acquisition originale du produit par le client chez le distribiteur 2 Cette garantie ne couvre aucun des points suivants a les contr les p riodiquies l entretien la r paration et le remplacement de pi ces par suite d usure normale b les frais et les risques de transport directs ou indirects ala mise en oeuvre de la garantie de ce produit c l endommagement dui produit r sultantd abus et de mauvais usage en particulier mais non de facon exclusieve la n gligence ou faute l utilisateur et l installation ou l utilisation de ce produit en contradiction avec les standards techniques ou de s curit en vigueur dans le pays o le produit est utilis reparations faites par les r parateurs non agr s d accidents de cas de force majeure ou de toute autre cause hors du contr le de DATEQ en particulier mas non de facon exclusieve la foudre l inondation incendie les troubles publics des piles qui ont coul une mauvaise ventilation postzegel stamp briefmarke timbre DATEQ B V De paal 37
21. or cord cannot be placed on it or against it Special attention must be paid to the point at which the cable is attached to the equipment and where the cable is connected to the power supply Ensure that foreign objects and liquids cannot get into the equipment The equipment must be cleaned using the method recommended by the manufacturer If the equipment is not being used for a prolonged period the power cable or power cord should be disconnected from the power supply In all cases where there is a risk following an incident that the equipment could be unsafe such as if the power cable or power cord has been damaged if foreign objects or liquids including water have entered the equipment if the equipment has suffered a fall or the casing has been damaged if a change in the performance of the equipment is noticed it must be checked by appropriately qualified technical staff The user may not carry out any work on the equipment other than that specified in the operating instructions audo technologies Dateq BCS25 manual Introduction Introduction The BCS 25 is specifically designed for applications requiring a full featured mixing console while being restricted by dimensional and or financial limits Post production rooms OB vans on location transmission studios and secondary studios are only a few of the possible uses for the BCS 25 The BCS 25 frame is supplied with 8 input channels optiona
22. or replacements of parts due to normal wear and tear b home service transport costs and other costs and risks of transport relating directly or indirectly to theguarantee of this product c damage to this product resulting from abuse and misuse including but not limited to the failure to use this product for its normal purposes or in accordance with DATEQ s instructions on the proper use and maintenance of this product and the installation or the use of this product in a manner inconsistent with the technical or safety standards in force in the country where the product is used repairs done by non authorised service stations lents acts of God or any cause beyond thecontrol of DATEQ including but not mited to lightning water fire public disturbances and improper ventilation GARANTIE BEDINGUNGEN DATEQ gew hrleistet f r die Garantiezeit dieses Ger t ab dem Zeitpunkt des Ersterwerbs keine Material und Verarbeitungsfehler aufweist Die Garantiezeit betr gt 12 Monate Sollten sich w hrend der Garantiezeit M ngel des Ger tes herausstellen die auf Material oder Verarbeitungsfehlem beruhen wird gem den nachstehenden Bedingungen DATEQ ohne Berechnung der Arbeits und Materialkosten das Ger t oder seine schadhaften Teile reparieren 1 Garantieleistungen werden nur erbracht wenn die Garantiekarte zusammen mit der Originalrechnung bzw dem Kassenbeleg die der Handler dem Verbraucher ausgestellt hat vorgelegt wird
23. produkt c schade aan dit product ten gevolge van mistbruik of verkeerd gebruik met inbegrip van maar niet beperkt tot abnormaal gebruik niet in overeenstemming met de DATEQ instructies over juist gebruik en onderhoud van het produkt en het installeren of gebruiken van dit produkt tegenstrijd met de technische of veiligheidsnormen zoals die van kricht zijn in het land waar het produkt wordt gebruikt reparaties uitgevoerd door niet erkende service stations ongevallen force majeur of welke oorzaak dan ook buiten de macht van DATEQ met inbegrip van maar niet beperkt tot bliksem water vuur publieke oproer en ondeugdelijke ventilatie GARANTEE CONDITIONS DATEQ guarantees this product to be free of defects in materials and workmanship at the time ofits original purchase for the period of 12 months If during this period of guarantee the product proves defective due to improper materials or workmanship DATEQ will repair or this product or its defective parts on the condetions explained hereafter 1 The guarantee will be granted only if the correctly filled out guarantee card is presented together with the original invoice cash ticket issued to the consumer by the retailer DATEQ reserves the right to refuse guarantee service if this information or the products serial number has been removed or changed after the original purchase of the product 2 This guarantee covers none of the following a periodic check ups maintenance repair
24. put VU meter The VU meter indicates the level of the selected source The upper LED s will blink when the level in the master module is too high the limit is 6dB under clip level Fader 100mm long volume control for the program signal Dateq BCS25 manual BCS27 Master module PGM TBK Source selector for the guest output Switches between program and talkback GST Volume control for the guest headphone output ANN Volume control for the announcer headphone output STUD Volume control for the studio output AIR CR Source selector for the studio announcer and guest outputs CUE Volume control for the CUE headphone output PGM ALL Talk buttons These buttons enable the talkback function to the selected source The ALL button talks to Guest announcer CUE and CF when this function is enabled CUE Headphones output Special functions The studio output can be toggled to follow the program signal or the selection indicated on the source selector Toggle between these functions by pressing the AIR and the CR button simultaneously By default the studio output will follow the program signal It is possible to enable or disable the talk to program function This is done by simultaneously pressing the AIR and talk to program buttons When the talk to program function is activated the control room will be muted By default this function is disabled The guest output can be used as an external communicatio
25. stalling the mixer unit The BCS25 is supplied as standard without a cabinet or connector cables It is possible to make cables for connecting to the Sub D connectors of the various input and output modules in house Only use connectors with metal cans and shielded cables for optimal HF rejection Installing into a cabinet The BCS25 frame fits into an opening of 445 x 395 x 110 mm W x H x D 395 445 110 To Be MCA 100 EE Dateq BCS25 manual BCS25 E dual line microphone input module BCS25 E dual line microphone input module The BCS25 E input module is available with or without 3 band equaliser The module can handle up to 3 different signals 2 stereo line and a mono microphone Line input 1 and the microphone input of this module are electronically balanced Line input 2 is unbalanced but can be turned into a balanced input by use of an extra pushon balanced line input module The microphone input is equipped with phantom power which can be switched off Line 1 Line 2 Input selector When the switch is pushed green LED is e lighted line 2 is selected Mic Input selector When the switch is pushed green LED is lighted the microphone input is selected regardless of the inputselector for line 1 or line 2 Overload The LED in the mic switch lights up red when the signal level anywhere in the module is too high and distortion can occur the limit is 6dB under cliplevel Gain Vo
26. telephone input module BCS26 E telephone input module The BCS26 E telephone input module is available with or without 2 band equaliser The module is equipped with a built in analogue telephone hybrid Telephone lines can be directly connected to this channel Besides the built in hybrid an external hybrid or talk show system can be connected In that case the BCS26 E channel operates as remote control only Galea BCS26E ringer overload 3 p l GAIN Pp 15 TUR 6 55 NY 1 AUX EN 30 00 2 1 1 y BAL ze 3 3 On Off Overload Gain R bal High Low AUD PGM AUX BAL CUE ON Fader Switches the external hybrid on or off The green LED will light up at an incoming ringer signal The LED in the off switch lights up red when the signal level anywhere in the module is too high and distortion can occur the limit is 6dB under cliplevel Volume pre setting Range 15dB to 6dB Compensation for the resistive part of the line impedance High tone control BCS26E only Shelving 12dB 3 5kHz Low tone control BCS26E only Shelving 12dB 600Hz Bus routing switches When a switch is pushed yellow LED is lighted the signal will be routed to the selected output Volume control for AUX1 level The AUX1 bus is pre fader Balance control The signal is placed at the desired position in the stereo image Pre fader listening The LED lights up green when the C
27. the main PCB above the bussconnector jumper J8 and J9 see drawing G NO FSC OFF G NO FSC OFF G NO FSC OFF Come MM FSC SW FD FSC SW FD meee me FSC SW FD c c 55000 T amp T Q N T amp Jumpers J8 and 9 select the type of operation It is possible to choose between faderstart figure 1 buttonstart figure 2 or the fader switch combinaton figure 3 EN Dateq BCS25 manual BCS25 E dual line microphone input module FADER SWITCH COMBINATION When the fader switch combination is selected the connected equipment can be started in two different ways 1 Pushing the startbutton when the fader is closed The connected equipment will start as soon as the fader is opened 2 Opening the fader The connected equipment will start as soon as the button is pressed To start the connected equipment 2 conditions have to be fulfilled When just one of the conditions is fulfilled the LED in the button will light up dimmed to indicate that the equipment will be started as soon as the fader is opened the ON is pressed The equipment will stop as soon as the button is pressed or the fader is closed Remote control output The BCS25 E module can generate a continues or pulsed start stop signal Jumper J13 at the m
28. tion is extremely well equipped It has a 40 segment LED VU meter with peak hold function that can be linked to PGM out or each of the other sources In addition the BCS27 has a master fader for PGM out an adjustable headphone output for monitoring any signal level controls for other outputs such as aux audition etc Any signal can be selected to the monitor outputs control room or headphone by means of the switching matrix The dedicated guest and the presenter outputs have a very practical feature The engineer is able to send a different signal mix than the actual PGM to each of those two outputs This enables him her to perform simple timesaving post production during transmission type of operations Communication between engineer guest and presenter is completely handled by the console offering numerous possibilities The most interesting one is the ability to rout the communication signal to the PGM output This option has been specifically implemented for live on location OB transmissions it presents a direct and easy communication channel with the studio engineer while news and commercials are broadcast from the home base studio Product support If you have any questions concerning the BCS25 its accessories or other products please contact Dateq Audio Technologies B V De Paal 37 Telephone 31 36 54 72 222 NL 1351 JG Almere Fax 31 36 53 17 776 The Netherlands E mail info dateg nl Internet www dateg nl In
Download Pdf Manuals
Related Search