User manual - COMM-TEC
Contents
1. ShowMe button of a DaisyNET TX working at HDBT Pass through status the very DaisyNET TX worked at Local Input status before will change to HDBT Pass through status To cancel this operation mistake press ShowMe button for more than 3 seconds and all DaisyNET TXs will recover their statuses before the press action 2 RS232 Control For the command set please ask your certified dealer Page 11 Vers 1 0 COMM TEC 3 Control Software 1 The Interface of PC Control Software rotary switch at 0 6 O HDMI O DP VGA HDBT Figure 7 2 Connect COM Port Connect RS232 port to PC Select COM Port and Click Connect button if the COM Port is correct the Connect status will change to Connected Figure 8 3 Set Rotary Switcher to position 9 Assign Address Type a 2 digit HEX number from 00 to FF in address column click Write to set Vers 1 0 Page 12 COMM TEC address Click Read button to get address RX LongCable Setting only for DaisyNET RX Turn ON or Turn OFF LongCable mode FACTORY RESET Click Reset button to recover to factory settting rotary switch at9 rotary switch at 0 6 Assign Address RX LongCable Setting FACTORY RESET Address o 8 ON 28 OFF Figure 9 4 Set Rotary Switcher to position 0 6 recommend 6 Port Select only for DaisyNET TX Enter Address of DaisyNET TX you want to control If unit has no address you must assign an address Cl2. 100M Ethernet with the HDMI signal RS232 Port for firmware update or RS232 control This model could be cascaded Vers 1 0 Page 6 25 Notice d D i P if iY M Vw A D bk TI W PT V W D d J H i EK H ha COMM TEC reserves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice A Warning To reduce the risk of fire electric shock or product damage 1 Do not expose this apparatus to rain moisture dripping or I splashing and that no objects filled with liquids such as vases shall be placed on the apparatus 2 Do not install or place this unit in a bookcase built in cabinet or confined in another space Ensure the unit is well ventilated 3 To prevent risk of electric shock or fire hazard due to overheating do not obstruct the unit s ventilation openings with newspapers tablecloths curtains and similar items 4 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 5 Do not place sources of naked flames such as lighted candles on the unit Page 7 6 Clean this apparatus only with dry cloth 7 Unplug this apparatus during lightning storms or when unused for long periods of time 8 Protect the power cord from being walked on or pinched particularly at plugs 9 Only use attachments accessories
3. HD DLP to DaisyNET RX1 and DaisyNET RX2 Connect a CAT 5E 6E AWG 23 cable from UTP output of DaisyNET TX1 to UTP input of DaisyNET TX2 Connect a CAT 5E 6E AWG 23 cable from UTP output of DaisyNET TX2 to UTP input of DaisyNET RX1 Connect a CAT 5E 6E AWG 23 cable from UTP output of DaisyNET RX1 to UTP input of DaisyNET RX2 Connect Ethernet Port of DaisyNET TX RX to PC Network Switch Router Attention Please insert and extract cables gently Connections Diagram DaisyNET TX DaisyNET TX DaisyNET RX DaisyNET RX 1 2 1 2 HOMI DisplayPort VGA HOMI DisplayPort VGA Cable Cable Cable Cable Cable Cable HD DVD LAPTOP HD DVD LAPTOP HD LCD HD LCD Figure 6 Vers 1 0 Page 10 Operation Instruction 1 ShowMe Button DaisyNET TX has two statuses HDBT Pass through and Local Input At HDBT Pass through status DaisyNET TX is used as a HDBT Extender All input led indicators go out at this status Press ShowMe button to change to Local Input status At Local Input status DaisyNET TX is used as a 3 Input Switcher Press ShowMe button to select input port To change back to HDBT Pass through status you must press ShowMe button for more than 3 seconds X ShowMe button also has an operation cancel function For example several DaisyNET TXs are connected together there is always one DaisyNET TX working at Local Input status and others working at HDBT Pass through status If you mistakenly press
4. specified by the manufacturer 10 Refer all servicing to qualified service personnel Vers 1 0 m Package Contents Transmitter 4 Main unit NO 1 P N_DaisyNET TX 2 Operating instructions P N INS DaisyNET TX RX 3 5VDC power supply DIN VDC0503 m Package Contents Receiver 1 Main unit NO 2 DIN DaisyNET RX 2 Operating instructions P N INS DaisyNET TX RX 3 5VDC power supply DIN VDC0503 m Panel Descriptions 1 DaisyNET TX CON DD OF W YP Front Panel Figure 2 5VDC Power and Indicator HDMI Input and Indicator Displayport Input and Indicator VGA and Audio Input and Indicator Ethernet Port ShowMe Button and Extend Port EDID and Update Switcher RS232 Port Vers 1 0 Page 8 Side Panel Link gt lt Act LINK OUT Link gt I lt Act LINK IN Figure 3 1 UTP Input 2 UTP Output 2 DaisyNET RX Front Panel Figure 4 5VDC Power and Indicator HDMI Output and Indicator Ethernet Port Update Switcher RS232 Port O A O N 2 Side Panel Link gt CH lt AC LINK OUT Link gt CH lt Act LINK IN Figure 5 1 UTP Input 2 UTP Output Page 9 Vers 1 0 m Connections and Operations 7 Use two DaisyNET TXs and two DaisyNET RXs for example Connect the HDMI Displayport VGA input source 3 such as HD DVD PS3 STB PC etc to DaisyNET TX1 and DaisyNET TX2 Connect the HDMI sink 3 such as HD LCD
5. 5 SYSTEM MIT 1 SENDER UND I EMPF NGER ccccssscccceeeccceesececeeeccecaeceeeeeeeeeaes 23 SYSTEM MIT MEHREREN SENDERN UND EINEM EMPF NGER vuuneeeessseessssenesennesenn 23 SYSTEM MIT MEHREREN SENDERN UND MEHREREN BMDPANGERN 24 OC SG NE EE 24 EINSCHALTEN see 25 QUELLEN ANSCHLIEBEN SENDER 0ccccceeecccessccccesccecesececeesececeesecseeeceeeueeseeees 25 EXTERNEN TASTER ANSCHLIEBEN LGSENDER TA 25 Page 5 Vers 1 0 HDMI Switcher and Extender By single CAT 5E 6E AWG 23 cable Product Overview Model Number DaisyNET TX RX BE gt 2 _ R5232 kA hie p SI Min ec e I te Mn pg p Vire d LS HOMI OUT In NUN we JO SS Bu Via MM pos ES DE SCH se RS232 el an Wii UNI e Bu e gel em Sho Nina MA gt GAIN SU HN N an 2 SH WW KH Sa een Figure 1 Features Use single UTP LAN cable CAT 5E 6 AWG 23 to substitute HDMI cable to achieve long distance transmission UTP cable termination follows the standard of IEEE 568B Transmission distance reaches up to 100 meters under the video format of 1080P Auto adjustment of feedback equalization and amplify the user does not need to care about the length of the cable HDMI V1 4 supported HDCP compliant Full HD support 1080p 60HZ 48 b pixels 3D and 4Kx2K max 30 m With LED indicators to show the power status With ESD protection inside Mounting ears supplied Transfer 10M
6. DaisyNET TXRX operating instructions V 1 0 doc Model No DaisyNET TX RX Operating Instructions Thanks for purchasing our product Please be sure to read this instruction manual carefully before using our product Version 1 0 CE Ba E COMM TEC Vers 1 0 Page 2 Introduction DaisyNET TX RX is a pair of HDBaseT switcher extender splitter while using CAT 5E 6 AWG 23 cable as transmission media Benefits from using DaisyNET TX RX 1 The length of HDMI cable is fixed and unchangeable after it is produced Because the HDMI connector can only be soldered or terminated by professional worker in factory the users can not reduce or increase by themselves However CAT 5E 6E AWG 23 cables are available everywhere and be processed easily by the user or installer By using DaisyNET TX RX the transmission distance for 1080P reaches 100 meters For general HDMI cables cables must be customized when the length over 10 meters DaisyNET TX RX has the ability of buffering and amplifying Series connection of DaisyNET TX RX achieves long distance transmission of HDBaseT signals When two pairs or more DaisyNET TX RX are stacked together they can be used to replace the centralized switching and distribution DaisyNET TX RX offers solutions for digital entertainment center HDTV retail and show site HDTV STB DVD and Projector factory noise space and security concerns data center control information distribution confere
7. ate Kit to upgrade Vers 1 0 Page 16 Specifications Operating Temperature Range 0 to 35 C 32 to 95 F Operating Humidity Range 5 to 90 RH no condensation Inout DDC Signal 5 volts p p TTL HDMI 1080P 1 080i 720P 576P 480P 576i 480i Video Format Supported DisplayPort amp VGA 800x600 1024x768 1280x1024 1400 x1050 1600 x1200 1920 x1080 1920 x1200 Output Video HDMI 1 4 HDCP Output Audio DTS HD Dolby HD Maximum Transmission Distance 100 meters CAT 5e 6 AWG 23 Power Supply 5VDC 11Watts MAX DaisyNET TX 12Watts MAX DaisyNET RX Dimensions 223mm Hx109mm Wx27mm D Mass Main unit 1 3Kg Pairs Power Consumption NOTE1 Specifications are subject to change without notice Mass and dimensions are approximate Page 17 Vers 1 0 m Typical Application As many as needed As many as needed y source Display Display Display Display Figure 13 m Maintenance Clean this unit with a soft dry cloth Never use alcohol paint thinner or benzine to clean this unit m Product Service e Provided Service 1 Damage Requiring service The unit should be serviced by qualified service personnel if e The DC power supply cord or AC adaptor has been damaged e Objects or liquids have gotten into the unit e The unit has been exposed to rain e The unit does not operate normally or exhibits a marked change in performance e The unit has been dropped or the cabinet damaged 2 Servic
8. e 12 Set Rotary Switchers of all units to position 6 Choose one DaisyNET TX for example TX3 connect its RS232 Port to PC run PC control software you can control TX3 and units connected behind TX3 s UPT OUT port from TX4 to TXN and RX1 to RXN You cannot control units connected before TX3 s UTP IN port TX1 and TX2 Vers 1 0 Page 14 Setting Instruction 1 Pin definition of extend port for ShowMe Pull up osv der 2 Pin definition of RS232 Port x 3 EDID and Update Switcher Instruction of DaisyNET TX 7 1080P stereo Using Embedded EDID note1 1080P 5 1ch Using Embedded EDID note1 1080P 7 1ch Using Embedded EDID note1 1080P 3D stereo Using Embedded EDID note1 1080P 3D 5 1ch Using Embedded EDID note1 1080P 3D 7 1ch Using Embedded EDID note1 Using the specified EDID Can upload EDID data to DaisyNET TX via RS232 RS485 note2 Upgrade for HDBT RX chip notes Upgrade for HDBT TX chip note4 Upgrade for MCU noted Page 15 Vers 1 0 4 Update Switcher of Instruction DaisyNET TX Upgrade for HDBT RX chip note3 ECO Upgrade for HDBT TX chip note4 9 Upgrade for MCU note5 Note 1 Only for HDMI Input of DaisyNET TX Note 2 For HDMI and Displayport Input of DaisyNET TX Note 3 Connect RS232 port to PC use HDBT RX Update Kit to upgrade Note 4 Connect RS232 port to PC use HDBT TX Update Kit to upgrade Note 5 Connect RS232 port to PC use MCU Upd
9. ick Read button to get current selected input port Select Port and click Write to set rotary switch at9 rotary switch at 0 6 rotary switch at 0 6 Port Select Address 01 e HDMI C VGA HDBT og Figure 10 EDID Edit only for HDMI and DP inputs of DaisyNET TX Select HDMI or DP Port click Read button to get current EDID Click Save as button to save EDID read from display equipment as bn file Click Open button to open saved bin file select the Input Port in Port Select Page 13 Vers 1 0 COMM TEC column Click Write button to set EDID of this Input Port the same as bin file Figure 11 5 EDID Copy Connect DaisyNET TX UTP OUT to DaisyNET RX UTP IN Set both Rotary Switchers to position 6 Connect RS232 port of DaisyNET TX to PC and run PC control software Enter Address of DaisyNET RX you want to read EDID from If unit has no address you must assign an address at first Select HDMI Port click Read button to get EDID from the display connected to DaisyNET RX Enter Address of DaisyNET TX you want to copy EDID to Select HDMI Port click Write button to set EDID the same as the display 6 Cascade Control Connect DaisyNET TXs and DaisyNET RXs as below all units must be assigned different address at first DaisyNET TX DaisyNET TX DaisyNET TX DaisyNET TX DaisyNET RX DaisyNET RX 1 2 3 N 1 N Figur
10. ignal des Senders hat Page 21 Vers 1 0 Auch die Empf nger k nnen beliebig oft kaskadiert werden Alle Empf nger geben das gleiche Signal wieder Anschl sse 1 DaisyNET TX Sender Transmitter Tx Front Ansicht Figure 14 1 DC Anschluss f r das Netzteil mit berwurf Mutter und LED Anzeige 2 HDMI Eingang und LED Anzeige leuchtet wenn dieser Eingang aktiv ist 3 Displayport Eingang und LED Anzeige leuchtet wenn dieser Eingang aktiv ist 4 VGA und Audio Eingang mit LED Anzeige leuchtet wenn dieser Eingang aktiv ist 5 Ethernet Port 6 ShowMe Taster und Anschluss f r externen Taster 7 Multifuktionsschalter f r EDID und Update Einstellungen 8 RS232 Port Seiten Ansicht Link gt C lt Act LINK IN Link gt CI lt Act LINK OUT Figure 15 1 Link Eingang 2 Link Ausgang Vers 1 0 Page 22 2 DaisyNET RX Empfanger Receiver Rx Front Ansicht HDMI OUT Ethernet Update 1 2 3 4 5 Figure 16 DC Anschluss f r das Netzteil mit berwurf Mutter und LED Anzeige HDMI Ausgang und LED Anzeige Ethernet Port Multifunktionsschalter RS232 Port oar O N gt Seiten Ansicht Link gt lt Act LINK IN Link gt lt Act LINK OUT Figure 17 1 Link Eingang 2 Link Ausgang Inbetriebnahme Es wird empfohlen die Gerate im ausgeschalteten Zustand zu verbinden Verkabelung des Systems System mit 1 Sender und 1 Empfanger Verbinden Sie die beiden Gerate i
11. ing Personnel Do not attempt to service the unit beyond that described in these operating instructions Refer all other servicing to authorized servicing personnel 3 Replacement parts When parts need replacing ensure the service uses parts specified by the manufacturer or parts that have the same characteristics as the original parts Unauthorized substitutes may result in fire electric shock or other hazards Vers 1 0 Page 18 4 Safety check After repairs or service ask the service to perform safety checks to confirm that the unit is in proper working condition e Warranty If your product does not work properly because of a defect in materials or workmanship COMM TEC referred to as the warrantor will for the length of the period indicated as below Parts 2 Year which starts with the date of original purchase Limited Warranty period at its option either a repair your product with new or refurbished parts or b replace it with a new or a refurbished product The decision to repair or replace will be made by the warrantor During the Labor Limited Warranty period there will be no charge for labor During the Parts warranty period there will be no charge for parts You must mail in your product during the warranty period This Limited Warranty is extended only to the original purchaser and only covers product purchased as new A purchase receipt or other proof of original purchase date is required fo
12. n Schlie en Sie nun die Netzteile an die Sender und Empf nger an und ziehen Sie die berwurfmuttern handfest an Bitte keine Zangen oder hnliche Werkzeuge dazu verwenden Nach einstecken der Steckernetzteile ist die Anlage betriebsbereit Zu erkennen ist dies an den LEDs links neben dem DC Anschluss Quellen anschlie en Sender Bitte verwenden Sie zur Verbindung Ihrer Quellen mit den Sendern nur Markenkabel z B Gefen Kabel Schlie en Sie das Kabel an der Quelle und am Sender an Dr cken Sie nun die ShowMe Taste so oft bis die LED links unten an dem von Ihnen genutzten Eingang des Senders leuchtet Nach einer kurzen Verz gerung HDCP Handshake EDID Kommunikation kommt das Signal das Sie einspeisen an der HDMI Buchse des Empf ngers an und wird angezeigt Machen Sie dies f r alle Quellen die Sie benutzen wollen Externen Taster anschlie en Sender Schlie en Sie die beiden Pole eines Tasters mit Hilfe eine passenden Kabels an den mitgelieferten 2 poligen Phoenixstecker an Dann stecken Sie den Phoenixstecker in den Anschluss lt ShowMe gt auf der Front des Senders Damit ist der externe Taster dem eingebauten Taster parallel geschaltet Sie d rfen nur potenzialfreie Kontakte verwenden Page 25 Vers 1 0 COMM TEC Vers 1 0 Page 26 COMM TEC Page 27 Vers 1 0 COMM TEC COMM TEC Vertriebsgesellschaft mbH Siemens Str 14 D 73066 Uhingen f 49 7161 3000 0 w www comm tec de
13. n dem Sie ein CAT 5E oder CAT 6 Kabel AWG 23 am Sender und Empf nger anstecken Dabei verbinden Sie den Link Ausgang des Senders mit dem Link Eingang des Empf ngers System mit mehreren Sendern und einem Empf nger Verbinden Sie alle Sender untereinander in dem Sie jeweils ein CAT 5E oder CAT 6 Page 23 Vers 1 0 Kabel AWG 23 an den Sendern anstecken Dabei verbinden Sie den Link Ausgang des ersten Senders mit dem Link Eingang des nachsten Senders Das machen Sie so oft bis alle Sender untereinander verbunden sind Dann verbinden Sie den Link Ausgang des letzten Senders mit dem Link Eingang des Empfangers System mit mehreren Sendern und mehreren Empfangern Verbinden Sie alle Sender untereinander in dem Sie jeweils ein CAT 5E oder CAT 6 Kabel AWG 23 an den Sendern anstecken Dabei verbinden Sie den Link Ausgang des ersten Senders mit dem Link Eingang des nachsten Senders Das machen Sie so oft bis alle Sender untereinander verbunden sind Dann verbunden Sie den Link Ausgang des letzten Senders mit dem Link Eingang des ersten Empfangers Nun verbinden Sie die Empfanger untereinander auf die gleiche Art wie die Sender Link Out des ersten Empfangers mit dem Link In des nachsten Empfangers Und auch das machen Sie so oft bis alle Empfanger untereinander verbunden sind Blockschaltbild DaisyNET TX DaisyNET TX DaisyNET RX DaisyNET RX 1 2 1 2 HOMI splayPort ve A HDMI splayPort VGA Figure 18 Vers 1 0 Page 24 Einschalte
14. nce room presentation school and corporate training environments Page 3 Vers 1 0 Contents INTRODUCTION eege 3 CONTENTS EN 4 HDMI SWITCHER AND EXTENDER o c ccccccccccscccccccccccccccccccccsccees 6 BY SINGLE CAT 5E 6E AWG 23 CABLE ccsccossscccsccccsccccscccccsccccssccoseces 6 m PRODUCT OVERVIEW MODEL NUMBER DAISYNET TX RX 6 ST MN 6 m PACKAGE CONTENTS TRANSMITTER esrornevnevnennennenennennennennenennennennenennennennenneneene 8 m PACKAGE CONTENTS RECEIVER sssssnesosososesnesesesosesesresesesososesresesesosesreseseseseses 8 m PANEL DESCRIPTIONS resrnerevnennvnennnnennnnenennenennenennnnennnnensnnenennenennenennnnennnnennnnennnnene 8 E EI IN EE 8 ES SE SEERE EEE ae 9 m CONNECTIONS AND UPERATIONS 10 m CONNECTIONS DIAGRAM cccccececceccecececcecscecscscscscuccsceseececscecscscesescueesees 10 OPERATION INSTRUCTIONS 2 cccccccccccccccccccccccccccccccccccccccccccccccccccccccsecs 11 L SHOWME IB AR e e CN 11 FEN 11 3C ONTROL e KE AEN 12 E SPECIFICATIONS 3 2 aaea a een 17 m TYPICAL APPLICATION s eerornvnevnvnennvnennvnennnnennnnensnnensenensnnensnnensnnenennnnennnnennnnensnnene 18 SINN 18 STP TIN 18 STN NN 18 VV OT 20113 EEE EEE EEE 19 e Warranty Limits And Evclueions 19 DEUTSCHE KURZANLEITUNG e eseessevsevsevneenevnernnennerneenernernernnrnnernerneeneeneeneeee 21 ICH AN e 2l Vers 1 0 Page 4 EE 22 NN NN 23 Verkabelung des Ayeiemte 2
15. nktion Die DaisyNET Ger te erlauben HDBaseT Signale durch kaskadieren von Ger ten Daisy Chain ber sehr gro e Entfernungen zu bertragen Dabei werden preiswerte und leicht zu erhaltende Kabel verwendet Die Anzahl der Ger te ist nicht begrenzt es k nnen beliebig viele Ger te zusammengeschaltet werden Das geschieht ohne Konfiguration oder andere Anwendereingriffe Die Ger te werden verbunden eingeschaltet und sind betriebsbereit Diese Anwendung unterscheidet zwei Ger tearten Sender und Empf nger Ein Sender speist ein AV Signal ein ein Empf nger gibt das Signal eines Senders wieder Der Sender verf gt ber drei verschiedene AV Anschl sse zum Einspeisen von Signalen e HDMI Eingang e DisplayPort Eingang e VGA Eingang mit zus tzlichem Stereo Audio Eingang Der Anwender kann jetzt ausw hlen welchen der Eing nge er an die Empf nger bertragen m chte Das geschieht durch eine sogenannte ShowMe Taste deutsch Zeig Mich Taste Der gew hlte Eingang wird durch eine LED am Sender signalisiert Sind mehrere Sender hintereinandergeschaltet ist das Signal aktiv das von dem Sender kommt an dem zuletzt die ShowMe Taste bet tigt wurde Der Empf nger verf gt ber eine HDMI Buchse an die ein Display oder ein Projektor angeschlossen wird An dieser Buchse liegt das Signal an das am Sender angew hlt wurde Da es keine Skalierung gibt liegt das Signal als HDMI Signal mit der gleichen Aufl sung an wie das aktivierte S
16. r Limited Warranty service e Warranty Limits And Exclusions 1 This Limited Warranty ONLY COVERS failures due to defects in materials or workmanship and DOES NOT COVER normal wear and tear or cosmetic damage The Limited Warranty ALSO DOES NOT COVER damages which occurred in shipment or failures which are caused by products not supplied by the warrantor or failures which result from accidents misuse abuse neglect mishandling misapplication alteration faulty installation set up adjustments misadjustment of consumer controls improper maintenance power line surge lightning damage modification or service by anyone other than a Factory Service Center or other Authorized Service or damage that is attributable to acts of God 2 There are no express warranties except as listed under limited warranty coverage The warrantor is not liable for incidental or consequential damages resulting from the use of this product or arising out of any breach of this warranty As examples this excludes damages for lost time Page 19 Vers 1 0 cost of having someone remove or re install an installed unit if applicable travel to and from the service location loss of or damage to media or images data or other recorded content The items listed are not exclusive but are for illustration only 3 Parts and service which are not covered by this limited warranty are your responsibility Vers 1 0 Page 20 Deutsche Kurzanleitung Fu
Download Pdf Manuals
Related Search