FPM-3120G Series User Manual
Contents
1. FPM 3120G Series Flat Panel Monitor with 12 1 Color TFT LCD Display User Manual Copyright Notice This document is copyrighted by Advantech Co Ltd All rights are reserved Advantech Co Ltd reserves the right to make improvements to the products described in this manual at any time Specifications are thus subject to change without notice No part ofthis manual may be reproduced copied translated or transmit ted in any form or by any means without the prior written permission of Advantech Co Ltd Information provided in this manual is intended to be accurate and reliable However Advantech Co Ltd assumes no responsibility for its use nor for any infringements upon the rights of third parties which may result from its use All brand and product names mentioned herein are trademarks or regis tered trademarks of their respective holders This Manual Covers the Following Models FPM 3120G XA e FPM 3120G RA FPM 3120G UA FPM 3121G XA e FPM 3121G RA FPM 3121G UA Part No 2003312080 20 Edition Printed in Taiwan February 2006 FPM 3120G Series User Manual li Product Warranty 1 year Advantech warrants to you the original purchaser that each of its prod ucts will be free from defects in materials and workmanship for one year from the date of purchase This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by A2. 2150DESK MT 1 Screw the hook and wall mounted brackets on the wall 2 Place the FPM 3120G series in the bracket Wall mounting Bracket Figure 2 1 Wall Mounting FPM 3120G Series User Manual 8 2 1 2 Panel Mounting Refer to figure 2 2 and follow the instructions below to install in a panel 1 Insert the FPM 3120G series into the cutout hole of the panel The dimensions of the cutout is 292 x 234 mm 11 5 x 9 22 Place eight panel mounting brackets on FPM 3120G series 2 on the top 2 on the bottom 2 on the left and 2 on the right Fasten the eight panel mounting brackets with screws Mount the FPM 3120G series monitor on the panel by the screws on the ten panel mounted brackets Figure 2 3 Panel Mounting 9 Chapter 2 2 2 Desktop Swing ARM for FPM 3120G Series The FPM 3120G series monitors can also be mounted in other ways You can use the desktop stand for desktop use or attach it on a swing arm bracket 2 2 1 Desktop Stand Refer to figure 2 4 The desktop stand bracket is attached to the rear of FPM 3120G series Simply attach the small bracket at the rear side ofthe monitor by screwing the two screws The bracket now becomes the desk top stand bracket The desktop stand kit is optional P N FPM 2150DESK MT Figure 2 4 Desktop Stand FPM 3120G Series 2 2 2 VESA ARM Mounting FPM 3120G Series User Manual 10 FPM 3120G series has been design
3. 5 Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer iii FCC Class B This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 ofthe FCC Rules These limits are designed to provide reasonable protection against harmful interfer ence when the equipment is operated in a residential environment This equipment generates uses and can radiate radio frequency energy If not installed and used in accordance with this user s manual it may cause harmful interference to radio communications Note that even when this equipment is installed and used in accordance with this user s manual there is still no guarantee that interference will not occur If this equipment is believed to be causeing harmful interfer ence to radio or television reception this can be determined by turning the equipment on and off If the interference is occurring the user is encouraged to try to correct the interference by one or more of the follow ing measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment to a power outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help FPM 3120G Series User Manual iv Packing List Before installing your equipment make sure that the following mater
4. 1 PenMount Control Panel The functions of the PenMount Control Panel are Calibrate Draw Multi ple Monitors Option and About which are explained in the following sections Calibrate This function offers two ways to calibrate your touch screen Standard Calibration adjusts most touch screens Advanced Calibration adjusts aging touch screens Standard Click this button and arrows appear pointing to red Calibration squares Use your finger or stylus to touch the red squares in sequence After the fifth red point calibration is complete To skip press ESC Advanced Advanced Calibration uses 4 9 16 or 25 points to effec Calibration tively calibrate touch panel linearity of aged touch screens Click this button and touch the red squares in sequence with a stylus To skip press ESC FPM 3120G Series User Manual 24 E7 PenMount Control P nel Calbrate Draw Multiple Monitors Option About The older the touch screen the more Advanced Mode calibration points you need for an accurate calibration Use a stylus during Advanced Calibration for greater accuracy NOTE 25 Appendix H 7 PenMount Control Panel Calibrate Draw Multiple Monitors Option About FPM 3120G Series User Manual 26 Plot Check this function and a touch panel linearity com Calibration parison graph appears when you have finished Data Advanced Calibration The blue lines
5. CD ROM 19 Appendix B Before installing the Windows 2000 XP driver software you must have the Windows 2000 XP system installed and running on your computer If you have an older version of the PenMount Windows 2000 XP driver installed in your system please remove it first Follow the steps below to install the PenMount Windows 2000 XP driver 1 When the system first detects the controller board a screen appears that shows Unknown Device Do not use this hardware wizard Press Cancel Found New Hardware Wizard Welcome to the Found New Hardware Wizard This ward helps you install software for Unknown If your hardware came with an installation CD gt or floppy disk insert it now What do you want the wizard to do O Install the software automatically Recommended Install from a Est or specific location Advanced Click Nest to continue C 2 FPM 3120G RA Insert the Driver CD ROM Go to TouchScreen DRV Penmont 9000 resistive Windows 2000 XP Driver Click setup exe FPM 3120G UA Insert the Driver CD ROM Go to TouchScreen DRV Penmount USB Windows Driver Click setup exe FPM 3120G Series User Manual 20 amp Windows 7000 XP Driver 4 01 Fle Edt View Favortes Tools Hep Ous OF Paw Drum H L Fie and Folder Tasks 9 perae thes fie GH Move the fie A copy then tie o Pta thes file to th C End thes He x Delete this file Other Places o permoti E My Moments
6. Exits the PenMount Monitor function FPM 3120G Series User Manual 34 B 4 3 PenMount Rotating Functions The PenMount driver for Windows 2000 XP supports several display rotating software packages Please see Chapter 5 for more information The PenMount drivers for Windows 95 Windows 98 Me Windows 2000 XP as well as Windows 98 USB and Windows Me 2000 XP sup port display rotating software packages such as e Portrait s Pivot Screen Rotation Software ATI Display Driver Rotate Function e nVidia Display Driver Rotate Function e SMI Display Driver Rotate Function Intel 845G GE Display Driver Rotate Function Configuring the Rotate Function 1 Install the rotation software package 2 Choose the rotate function 0 90 180 270 in the 34 party software The calibration screen appears automatically Touch this point and rotation is mapped Please touch the point pees NOTE The Rotate function is disabled if you use Monitor Mapping 35 Appendix B B 5 Uninstall the PenMount Windows 2000 XP driver Exit the PenMount monitor PM in the menu bar 2 Go to Settings then Control Panel and then click Add Remove program Select PenMount DMC9000 and click the Add Remove button by Currently r deZ prog ames Sort by Nane v Charan or C7 Pen tount D 3009 and DICH 00 3 Select PenMount DMC9000 and DMC9100 Click the Remove button Add or Remove Programs CFE installed prog ams Cit here for BEG
7. brightness of the display Contrast Contrast Adjust contrast of RGB channel simultanously Sub Contrast RGB Adjust color of selected RGB channel Position H Size Adjust phase of ADC sample clock Clock Phase Adjust number of clocks per line H Position Move input image capture window left or right V Position Move the input image capture win dow up or down Information Information System input mode information and maximum range supported by screen All Reset All Reset Reset menu parameters to factory default setting FPM 3120G Series User Manual APPENDIX Touchscreen This appendix contains information on the touchscreen its installation and configuration Appendix B Touchscreen B 1 Introduction The FPM 3120G Series optional touchscreen uses advanced 3MTM 8 wire resistive technology It provides more accurate sensing capacity than other technologies The touchscreen is specially designed for tough industrial environments and has been approved to FCC Class B stan dards B 2 Touchscreen Specifications Electrical e Contact bounce lt 10 ms gt Operating voltage 5 V typical Sheet Resistance 350 22 Q per Square e Linearity lt 1 5 full scale linearity error in either direction gt Insulation Resistance gt 20 MQ 25 V DC Durability Test conditions 4 H hardness 0 04 stylus pen 350 gram load e Point activation 1 Million activations on a single point with a 5 8 diameter silicone fi
8. its usual application as an LCD panel monitor the FPM 3120G XA Series comes standard with Direct VGA control signal input making it compatible with industrial PCs and workstations The OSD On Screen Display function allows you to adjust the display and turn the backlight on and off a function that is highly appreciated among experienced users of industrial flat panel monitors The whole chassis is made of durable stainless steel and the front panel is of aluminum with NEMA4 IP65 compliance For different applications we provide the two models with different reso lution The FPM 3120G XA series has original SVGA 800 600 resolu tion on 12 1 pane while FPM 3121G XA has XGA 1024 768 resolution This suits for applications that need more details For applications in harsh environments FPM 3120G XA can work at 10 60 C 14 140 F while FPM 3121G XA can work at 0 50 C 32 122 F Products in the FPM 3120G XA Series can also be provided in touch screen versions FPM 3120G RA 3121G RA and FPM 3120G UA 3121G UA With an 8 wire resistive type touchscreen this monitor can be immediately transformed into a remote control system The Advantech FPM 3120G XA series is the ultimate HMI solution for your industrial applications 1 2 Specifications General e Construction Heavy duty stainless steel chassis Front Panel Aluminum NEMA4 IP65 compliant e Control OSD On Screen Display control pad on front side e Mounti
9. only pro vides a click function and dragging is disabled Beep Enable Beep Sound turns beep function on and off Sound Beep on Pen Down beep occurs when pen comes Mode down Beep on Pen Up beep occurs when pen is lifted up Beep on both of Pen Down Up beep occurs on both Beep Frequency modifies sound frequency Beep Duration modifies sound duration FPM 3120G Series User Manual 32 About This panel displays information about the PenMount controller and driver version E PenMount Control Panel DER Calibrate Draw Multiple Monitors Option About PenMount DMC3000 and DMC9100 Driver Version 4 01 Firmware Version E mail salt saltcomtw Website www salt com tw Copyright C 2003 Salt Int l Corp 33 Appendix B B 4 2 PenMount Monitor Menu Icon The PenMount monitor icon PM appears in the menu bar of Windows 2000 XP system when you turn on PenMount Monitor in PenMount Util ities pm PenMount Monitor has the following functions Control Panel Right Button Pen Stabilizer Exit Beep Right Button Pen Sta bilizer Exit Turns beep on or off When you select this function a mouse icon appears in the right bottom of the screen Click this icon to switch between Right and Left Button functions Check this function to reduce cursor vibration for relatively unstable touch screens or where there may be excess vibration Normally this function is not checked
10. 120G UA Series 10 22 Desktop Stand cesesessessensesnennensennnnnensnnnnnnennenn 10 Figure 2 4 Desktop Stand FPM 3120G UA Series 10 2 2 2 VESA ARM Mounting sees sese eee eee eee eee e 11 Figure 2 5 Swing ARM FPM 3120G UA series 11 22 3 Power Adapter c cccicciviesccscsvecsscesecsensedescassercursesestoanents 12 Display Timing Mode amp OSD s000008 14 Supported Input Timing Modes 14 Table A 1 Supported Input Formats 14 Keypad Interfaces moserne e 15 Power Indicator LED Status sese eee eee 15 OSD N Tel 16 Touchscreen aaa 18 Introduction 2 52 22 ee bene 18 Touchscreen Specihcaniong sese eee 18 Installing Driver for Windows 2000 XP n se 19 Configuring PenMount Windows 2000 XP Driver 24 B 4 1 PenMount Control Panel 24 B 4 2 PenMount Monitor Menu Icon sss eee eee ee 34 B 4 3 PenMount Rotating Functions sees eee ee eee 35 Uninstall the PenMount Windows 2000 XP driver 36 ix Table of Contents FPM 3120G Series User Manual CHAPTER Introduction This chapter includes e Introduction e Specifications e LCD Specification e Power Consumption e Connectors e Dimensions Chapter 1 Introduction 1 1 Introduction Advantech s FPM 3120G series consists of 12 1 color TFT LCD flat panel monitors built specifically for industrial applications With the optional touchscreen the FPM 3120G RA series offers user friendly sys tem control interfaces In addition to
11. ERATURE IS BELOW 20 C 4 F OR ABOVE 60 C 140 F THIS MAY DAMAGE THE EQUIPMENT The sound pressure level at the operator s position according to IEC 704 1 1982 is no more than 70dB A FPM 3120G Series User Manual vi DISCLAIMER This set of instructions is given according to IEC 704 1 Advantech disclaims all responsibility for the accuracy of any statements contained herein Wichtige Sicherheishinweise 1 2 3 1 1 eat 12 13 14 Bitte lesen sie Sich diese Hinweise sorgf ltig durch Heben Sie diese Anleitung f r den sp teren Gebrauch auf Vor jedem Reinigen ist das Ger t vom Stromnetz zu trennen Ver wenden Sie Keine Fl ssig oder Aerosolreiniger Am besten dient ein angefeuchtetes Tuch zur Reinigung Die NetzanschluBsteckdose soll nahe dem Ger t angebracht und leicht zug nglich sein Das Ger t ist vor Feuchtigkeit zu sch tzen Bei der Aufstellung des Ger tes ist auf sicheren Stand zu achten Ein Kippen oder Fallen k nnte Verletzungen hervorrufen Die Bel ftungs ffnungen dienen zur Luftzirkulation die das Ger t vor berhitzung sch tzt Sorgen Sie daf r daB diese ffnungen nicht abgedeckt werden Beachten Sie beim AnschluB an das Stromnetz die AnschluBwerte Verlegen Sie die NetzanschluBleitung so daB niemand dar ber fallen kann Es sollte auch nichts auf der Leitung abgestellt werden Alle Hinweise und Warnungen die sich am Ger ten befin
12. O Dred Documents q My Computer Gy My Network Paces 3 The screen displays the installation wizard for the PenMount soft ware Click Next ie PenMount DMC9000 and DMC9100 InstallShield Wizard Welcome to the InstallShield Wizard for PenMount DMC9000 and DMC9100 The InstaliShield R Wizard wil install PeniMount DMC9000 and DMC9100 on your computer To continue cick Next 21 Appendix B 4 A License Agreement appears Click I accept and Next 2 PenMount DMC9000 and DMC9100 InstallShield Wizard License Agreement Please read the following license agreement carefully oftware License opynght C Salt International Corp All nghi reserved enMount Utilities drivers include DOS Windows 3 11 windows 95 Windows 98 Windows ME Windows NT indows 2000 Windows XP Windows CE Linux and Qnx drivers 0 copy modify or translate is prohibited except with Sal s written consents o license PenMount Utilities drivers contact Salt International Corp ai salt salt com tw ome page www salt com tw 1 accept the terms in the icense agreement Ol do not accept the terme in the license agreement 1 5 The Ready to Install the Program screen appears Select Install PenMount DMC9000 and DMC9100 InstallShield Wizard Ready to Install the Program The wizard is ready to begin installation Chick Install to begin the installation Tf you want to review or change any of your installation setti
13. Panel DER Calibrate Draw Multiple Monitors Option About C Point Mode IV Enable Beep Sound Beep Frequency 600 Hz G trad Laka C Beep on pen up L GLEB BU MD Br M EEE MR B RG MA C Beep on both Back to Driver Default 6 Touch this screen to start its calibration appears on one of the screens Touch the screen 7 Touch the red square messages appear Touch the red squares in sequence 8 Continue calibration for each monitor by clicking Standard Cali bration and touching the red squares 31 Appendix B NOTE 1 If you used a single VGA output for multiple monitors please do not use the Multiple Monitors function Just follow the regular procedure for calibration on each of your desktop monitors 2 The Rotating function is disabled if you use the Multiple Monitors function 3 If you change the resolution of display or screen address you have to redo Map Touch Screens so the system understands where the displays are Option This panel function supports two modes Operation Mode and Beep Sound Mode which allow configuration for specific touch screen appli cations such as point of sales POS terminals Operation This mode enables and disables the mouse s ability to Mode drag on screen icons useful for configuring POS termi nals Stream Mode Select this mode and the mouse func tions as normal and allows dragging of icons Point Mode Select this mode and the mouse
14. den sind zu beachten Wird das Ger t ber einen l ngeren Zeitraum nicht benutzt sollten Sie es vom Stromnetz trennen Somit wird im Falle einer berspan nung eine Besch digung vermieden Durch die L ftungs ffnungen d rfen niemals Gegenst nde oder Fl s sigkeiten in das Ger t gelangen Dies k nnte einen Brand bzw elek trischen Schlag ausl sen ffnen Sie niemals das Ger t Das Ger t darf aus Gr nden der elek trischen Sicherheit nur von authorisiertem Servicepersonal ge ffnet werden Wenn folgende Situationen auftreten ist das Ger t vom Stromnetz zu trennen und von einer qualifizierten Servicestelle zu berpr fen a Netzkabel oder Netzstecker sind besch digt vii b Fl ssigkeit ist in das Ger t eingedrungen c Das Ger t war Feuchtigkeit ausgesetzt d Wenn das Ger t nicht der Bedienungsanleitung entsprech end funktioniert oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen e Das Ger t ist gefallen und oder das Geh use ist besch digt f Wenn das Ger t deutliche Anzeichen eines Defektes aufweist Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 betr gt 70dB A oder weiger 15 VOSICHT Explisionsgefahr bei unsachgemaben Austausch der Bat terie Ersatz nur durch densellben order einem vom Hersteller empfohlen emahnlichen Typ Entsorgung gebrauchter Batterien navh Angaben des Herstellers 16 ACHTUNG Es besteht die Explosionsgefahr falls die Batteri
15. dvantech or which have been subject to misuse abuse accident or improper instal lation Advantech assumes no liability under the terms of this warranty as a consequence of such events All defective products under normal standard operation will be serviced by Advantech s global RMA system If an Advantech product is defec tive it will be repaired or replaced at no charge during the warranty period For out of warranty repairs you will be billed according to the cost of replacement materials service time and freight Please consult your dealer for more details If you think you have a defective product follow these steps 1 Collect all the information about the problem encountered For example CPU speed Advantech products used other hardware and software used etc Note anything abnormal and list any onscreen messages you get when the problem occurs 2 Call your dealer and describe the problem Please have your man ual product and any helpful information readily available 3 Ifyour product is diagnosed as defective obtain an RMA return merchandize authorization number from your dealer This allows us to process your return more quickly 4 Carefully pack the defective product a fully completed Repair and Replacement Order Card and a photocopy proof of purchase date such as your sales receipt in a shippable container A product returned without proof of the purchase date is not eligible for war ranty service
16. e auf nicht fachm nnische Weise gewechselt wird Verfangen Sie die Batterie nur gleicher oder entsprechender Type wie vom Hersteller empfohlen Entsorgen Sie Batterien nach Anweisung des Herstellers Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 betr gt 70dB A oder weiger Haftungsausschluss Die Bedienungsanleitungen wurden entsprechend der IEC 704 1 erstellt Advantech lehnt jegliche Verantwortung f r die Richtigkeit der in diesem Zusammenhang get tigten Aussagen ab DISCLAIMER This set of instructions is given according to IEC704 1 Advantech disclaims all responsibility for the accuracy of any statements contained herein FPM 3120G Series User Manual viii Chapter 1 1 1 1 2 1 3 1 4 1 5 1 6 Chapter 2 2 1 2 2 Appendix A A l Contents Introduction s sss sss ss sss sss sss sss sassa sss sasa 2 Introduction u 20 ee aa RR Er 2 Specifica ONS nannten TR TT 2 ECD Specifications a sand 3 Power Adapter Specifications sese eee eee eee 4 LS Te T TTT 4 Dimensions asus end hihi Hana ieee ees 6 Figure 1 1 FPM 3120G UA Chassis Dimensions 6 System Setup cccccccccccccsccsccsccsccsscscecescsrees Mounting FPM 3120G UA Series sse seene 8 2 1 1 Wall Mounting sees eee 8 Figure 2 1 Wall Mounting 0 0 sees eee eee eee 8 2 1 2 Panel Mounting Figure 2 2 Panel Mounting sese sees eee eee eee eee ee 9 Figure 2 3 Panel Mounting sese sees ee eee eee eee ee 9 a Swing ARM for FPM 3
17. ear the equipment and must be easily accessible 5 Keep this equipment away from humidity 6 Put this equipment on a reliable surface during installation Dropping it or letting it fall may cause damage 7 The openings on the enclosure are for air convection Protect the equipment from overheating DO NOT COVER THE OPENINGS 8 Make sure the voltage of the power source is correct before connect ing the equipment to the power outlet 9 Position the power cord so that people cannot step on it Do not place anything over the power cord 10 All cautions and warnings on the equipment should be noted 11 If the equipment is not used for a long time disconnect it from the power source to avoid damage by transient overvoltage 12 Never pour any liquid into an opening This may cause fire or electri cal shock 13 Never open the equipment For safety reasons the equipment should be opened only by qualified service personnel 14 If one of the following situations arises get the equipment checked by service personnel a The power cord or plug is damaged b Liquid has penetrated into the equipment c The equipment has been exposed to moisture d The equipment does not work well or you cannot get it to work according to the user s manual e The equipment has been dropped and damaged f The equipment has obvious signs of breakage 15 DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED ENVIRONMENT WHERE THE STORAGE TEMP
18. ed with support for the VESA arm standard Refer to figure 2 5 Figure 2 5 Swing ARM FPM 3120G series 2 2 3 Power Adapter Il Chapter 2 The power adapter bracket can be attached to the rear of FPM 3120G series Attach the bracket at the rear side of the monitor by screwing the four screws The DC terminal ofthe AC DC adapter can be locked on the rear case by the DC in Power Cord bracket FPM 3120G Series User Manual 12 A APPENDIX Display Timing Mode and OSD Appendix A Display Timing Mode amp OSD A 1 Supported Input Timing Modes The different frequencies below are already programmed in this module and the synchronous signal inputs are automatically recognized Table A 1 Supported Input Formats Vertical Frequencies Resolution 56 Hz 60 Hz 70 Hz 72 Hz 75 Hz 640 x 480 Yes Yes Yes 720 x 400 Yes 800 x 600 Yes Yes Yes Yes 1024 x 768 Yes Yes Yes Note 1 Even if the preset timing is entered some adjustment of func tions such as Horizontal period CLK delay and display position are required The adjusted values are memorized in every preset number Note 2 This module recognizes the synchronous signals with near preset timing of the frequency of the HS and Vsync even in the case that the signals other than the preset timing that were entered Note 3 Because adjustments may not fit such as differing magnifying ratios or in the case that you use it except for
19. for FPM 3121G XA 10 60 C 14 140 F for FPM 3120G XA gt Contrast Ratio 500 1 typ Lamp Life Time 50 000 hrs 1 4 Power Adapter Specifications s Max Output Power 42 W AC input voltage 100 240 V AC gt Output voltage 12 V 3 5 A e Safety Standards UL CE CCC TUV CB 1 5 Connectors The following connectors are on the bottom of the FPM 3120G XA Series VGA Port DB15 This DB 15 connector can be connected to the system via the external 15 pin DB 15 connector locatd on the left side of the system unit RS 232 Touchscreen Connector DB9 with FPM 3120G RA amp FPM 3121 G RA This connector will only be present if a touchscreen is installed It must be connected to the RS 232 port of the PC The touchscreen cable is included with all orders that include the touchscreen option USB Touchscreen Connector USB type B with FPM 3120G UA amp FPM 3121 G UA This connector will only be present if a touchscreen is installed It must be connected to the USB port of the PC The touchscreen cable is included with all orders that include the touchscreen option DC 12V Power In This connector connects to the DC 12V Switching Power Supply FPM 3120G Series User Manual 4 Warning Before you connect a VGA cable between the monitor and a PC please note the following issues 1 Ifyou have installed a operating system in the PC make sure the ver tical frequency is within the acceptable range Refe
20. ials have been received e FPM 3120G XA Series flat panel monitor e Accessory pack including AC DC adapter AC DC power adapter bracket Video signal cable 1 8m Fixed panel mounted bracket x 8 pcs Screw Bags M4x25 mm screws x 8 pcs DC in Power Cord bracket x 1 piece RS 232 cable 1 8m FPM 3120G RA 3121G RA only or USB cable 1 8m FPM 3120G UA 3121G UA only Driver manual CD ROM If any of these items are missing or damaged contact your distributor or sales representative immediately Additional Information and Assistance 1 Visit the Advantech web site at www advantech com where you can find the latest information about the product 2 Contact your distributor sales representative or Advantech s cus tomer service center for technical support if you need additional assis tance Please have the following information ready before you call e Product name and serial number Description of your peripheral attachments e Description of your software operating system version application software etc e A complete description of the problem The exact wording of any error messages Safety Instructions 1 Read these safety instructions carefully 2 Keep this User s Manual for later reference 3 Disconnect this equipment from any AC outlet before cleaning Use a damp cloth Do not use liquid or spray detergents for cleaning 4 For plug in equipment the power outlet socket must be located n
21. information To remove this program from your computer cick Remove 4 Select Yes and Close to remove the PenMount Windows 2000 XP driver and reboot the system FPM 3120G Series User Manual 36
22. lowing modes Windows Extend Monitor Function Matrox DualHead Multi Screen Function nVidia nView Function NOTE The Multiple Monitors function is for use with multiple displays only Do not use this function if you have only one touch screen display Please note once you turn on this function the Rotating function is disabled Enable the multiple display function as follows 1 Check the Enable Multiple Monitor Support box then click Map Touch Screens to assign touch controllers to displays E PenMount Control Panel Calibrate Draw Multiple Monitors Option About V Enable Multiple Monitor Support E 29 Appendix B 2 When the mapping screen message appears click OK C1PenMount Control Panel aag Calibrate Draw Multiple Monitors Option About IV Enable Multiple Monitor Support Mapping Please touch the panel as indicated in the following screens 3 Touch each screen as it displays Please touch this monitor Fol lowing this sequence and touching each screen is called mapping the touch screens Please touch this monitor FPM 3120G Series User Manual 30 4 Touching all screens completes the mapping and the desktop reap pears on the monitors Calibrate To start calibration please touch the panel to calibrate in the following screen Lx 9 Select a display and execute the Calibration function A message to start calibration appears Click OK PenMount Control
23. ng Panel wallmount desktop or VESA Arm FPM 3120G Series User Manual 2 Dimensions W x H x D 310 x 250 x 44 mm 12 0 x 9 84 x 1 73 Panel Mount Cut out Dimension WxH 292x234 mm 11 5 x9 22 Weight 3 0 kg 6 6 1b Vibration operating 5 500 Hz Random 1 Grms CE FCC BSMI CCC certified Power Consumption 12V 10 3 5 A Touchscreen Optional Type 8 wire analog resistive Resolution 1024 x 1024 Light Transmission 75 Gouge Hardness is greater than 4H per ASTM D3363 92 for HCC01 HCG10 and HCG12 Controller RS 232 interface for FPM 3120G UA 3121G RA version or USB 1 1 for FPM 3120G UA 3121G UA version Power Consumption FPM 3120G RA 3121G RA 5 V 200 mA FPM 3120G UA U 3121G UA 5 V 100 mA USB bus power OS Support Windows 2000 XP Life Span 1 000 000 activations typical at a single point with a 5 8 diameter silicone finger with a 350g load at 2 touches per second 1 3 LCD Specifications Display Type TFT LCD with XGA for FPM 3121G XA series or SVGA for FPM 3120G XA series Display Size 12 1 Max Colors 262 k Max Resolution 1024 x 768 for FPM 3121G XA series 800 600 for FPM 3120G XA series Viewing Angle H V FPM 3121G XA 120 100 FPM 3120G XA 140 120 Luminance 350 cd m Storage Temperature 20 60 C 4 140 F for FPM 3121G XA 20 70 C 4 158 F for FPM 3120G XA 3 Chapter 1 Operating Temperature 0 50 C 32 122 F
24. nger with a 350g load at 2 Hz s Character Activation Life gt 100 000 characters written within a 20 mm x 20 mm area on the touch screen e Chemical resistance Hard coating is highly resistant to most solvents and chemicals FPM 3120G Series User Manual 18 Optical e Visible light transmission 75 typical gt 74 550 nm test e Clarity Clear Finish 25 Antiglare Finish 15 Sensor board e Chemical strengthened glass with 4 H hardness standard Test condition ASTM D3363 92A Ball drop test e Able to bear a 225 g steel ball dropped from 660 mm elevation without breaking Environmental Specifications Operating Temperature Range 20 C 50 C 2 weeks at 50 C 90 RH Storage Temperature High 70 C 240 hours at ambient humidity Storage Temperature Low 40 C continuous at ambient humidity Accelerated Aging 100 hours at 60 C 95 RH Thermal Shock 25 cycles one cycle is 30 min dwell alternating from 40 to 85 C with less than 10 min transfer time B 3 Installing Driver for Windows 2000 XP The touchscreen has drivers for Windows 2000 and Windows XP You should read the instructions in this chapter carefully before you attempt installation Note 1 The following windows illustrations are examples only You must follow the flow chart instructions and pay attention to the instructions which then appear on your screen Note 2 Install the HMI CD Driver into the system CD ROM D means
25. ngs click Back Click Cancel to exk the wizard FPM 3120G Series User Manual 22 6 The next screen is Hardware Installation Select Continue Any Hardware Installation The software you are installing for this hardware PenMount DMC39000 and DMC3100 has not passed Windows Logo testing to verily its compatibility with Windows XP Tell me why this testing is important Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing STOP Ian 7 The InstallShield Wizard Completed appears Click Finish iI PenMount DMC9000 and DMC9100 InstallShield Wizard InstallShield Wizard Completed The InstallShield Wizard has successfully installed PenMount DMC9000 and DMC9100 Click Finish to exit the wizard We recomnenend you to reboot your computer to enable al the functions 23 AppendixB B 4 Configuring PenMount Windows 2000 XP Driver Upon rebooting the computer automatically finds the new 9000 control ler board The touch screen is connected but not calibrated Follow the procedures below to carry out calibration 1 After installation click the PenMount Monitor icon PM in the menu bar 2 When the PenMount Control Panel appears click Calibrate B 4
26. r to Appendix B 2 Ifyou have not installed a operating system you have to adjust the vertical frequency to fall within the range 5 Chapter 1 1 6 Dimensions a 232 AN 88 BE SB BE BB B8 B8 8E amp D i 250 RR ry YN 0 o D o o D i D D 1 8 G U g o o d KM aig amp EEE o w AY d ja e 1 S e 6 D a i w 0 8 0 o des 0 Y o te O p I L D T J g 27 86 nD lt gt Omo o mo fa La B B la Figure 1 1 FPM 3120G UA Chassis Dimensions FPM 3120G Series User Manual 6 CHAPTER System Setup e Mounting the Monitor e Wall Panel Mounting e Desktop Swing Arm Mounting Chapter 2 System Setup 2 1 Mounting FPM 3120G UA Series Monitors in the FPM 3120G series can be flexibly mounted The versatil ity ofthe FPM 3120G series mounts enable them to be mounted on your desk or almost anywhere else 2 1 1 Wall Mounting Please refer to figure 2 1 and follow the steps below to install FPM 3120G series on a wall The wall mounting kit is optional P N FPM
27. show linearity before calibration and black lines show linearity after calibration E PenMount Control Panel Calibrate Draw Multiple Monitors Option About Advanced Mode E lt VW Plot calibration data 27 AppendixB Draw Tests or demonstrates the PenMount touch screen operation The display shows touch location Click Draw to start Touch the screen with your finger or a stylus and the drawing screen registers touch activity such left right up down pen up and pen down Seles 4 PenMount Control Panel Calibrate Draw Multiple Monitors Option About Touch the screen with your finger or a stylus and the drawing screen reg isters touch activity such left right up down pen up and pen down ut me u rete in 7 reak Y terr Click Clear Screen to clear the drawing FPM 3120G Series User Manual 28 Multiple Monitors Multiple Monitors supports from two to six touch screen displays for one system The PenMount drivers for Windows 2000 XP support Multiple Monitors This function supports from two to six touch screen displays for one system Each monitor requires its own PenMount touch screen control board either installed inside the display or in a central unit The PenMount control boards must be connected to the computer COM ports via the RS 232 interface Driver installation procedures are the same as for a single monitor Multiple Monitors supports the fol
28. the display timing that was preset Note 4 The 1024 768 resolution is only possible with FPM 3121G XA FPM 3120G Series User Manual 14 A 2 Keypad Interface AUTO Press this button to execute auto adjustment process SEL Press to show the OSD screen or select an item to change its setting Press to move between items or increase decrease item set ting Press both buttons simultanously to lock unlock the current settings EXIT Press to close the selected item or the whole OSD screen ON OFF Press the ON OFF button to turn FPM 3120G UA s backlight on and off When power is off the power indicator will be blinking A 3 Power Indicator LED Status The keypad interface provides a driver for a dual color LED to indicate status 1 Green COMMON board detects a input signal and sends output sig nal to LCD panel 2 Orange No signal detected or out of range 3 Green and blinking Backlight is off 3 No color Power off 15 Appendix A A 4 OSD Function Each selected value is stored into LCD memory after SEL signal input or time out The stored values are not affected if the power is turned off But the selected value is not available in case a selected mode is changed before time out or power is turned off before time out The default definition of input keys is shown as following Main Menu Sub Menu Functionality Brightness Adjust
Download Pdf Manuals
Related Search