Home

Comfort and innovation –

1. Programming example Example 1 Objective You would like to change the factory settings of the Alarm and set output 2 Engine lock to control the normally open relay Sequence L d 3 Turn the ignition on Enter PIN code and wait for confirmation Enter Menu 1 by pressing and releasing the Programming button 10 times If you have performed all the actions correctly the Alarm will notify you with 3 audio and light signals According to Menu 1 select option 2 Engine lock by pressing the Programming button 2 times The Alarm will inform you about chosen menu option number by a series of 2 audio and light signals Enter option 2 by pressing and holding the brake pedal The Alarm will show option setting by a repeated double audio and light signals because the current factory set option setting is normally closed relay control Select the normally open relay control by pressing and releasing the Programming button 3 times The Alarm will inform you about chosen menu option with series of 1 audio signal Exit programming mode by turning the ignition off Example 2 Objective You would like to change the factory settings of the Alarm and increase AntiHiJack distance from 100 to 300 meters Sequence 1 2 GF i Turn the ignition on Enter PIN code and wait for confirmation Enter Menu 2 by pressing and releasing the Programming button 12 times If you have performed all the actions correctly the Alarm wi
2. The function monitors wipers and makes sure they are disabled Monitoring is fulfilled if the software neutral is enabled The driver is notified by a long audio signal The signal here means that wipers are enabled Used with alternative remote start module 12 Shutdown the engine in remote start Pulse on input stops or disables remote start 13 Parking brake The function is used when CAN bus does not contain data on hand brake position 14 15 Wake CAN bus Hazard lights status This function is used in exceptional cases please see Integrator This function is used in exceptional cases please see Integrator 16 Trunk state The function is used when CAN bus does not contain data on trunk status In this case Trunk input has to be connected to trunk terminal switch output 17 Digital button Used to enter PIN code or for other tasks 18 19 Close central lock Open central lock This function is used in exceptional cases please see Integrator This function is used in exceptional cases please see Integrator 20 21 22 23 24 25 26 27 Additional sensor input 1 Additional sensor input 2 Engine state in remote start Input to launch the heater Input for drivers door switch Factory security system alert Look for RFID tag Beach mode code Used to connect additional sensor Used to connect additional sensor Pulse to this input will iden
3. 2 disabled jai 1 by time 2 by engine temperature 11 Engine shutdown conditions 3 by time or engine temperature 12 Engine type 1 diesel 2 gasoline 3 hybrid 13 Starter delay only for diesel engines 1 5 sec 4 20 sec _ E 1 600 rpm 6 1100 rpm Detected automatically 14 Idle RPM 1 6 Set up manually if required 15 Engine runtime in remote start l 12 3 1 10 min 3 30 min 12 120 min 16 Engine shutdown temperature in remote start 1 14 12 l pra ance oS ae 1 30 C 2 20 C 3 15 C 4 10 C 17 Temperature to launch the engine by temperature 1 8 1 5 5 C 6 0 C 7 5 C 8 40 0c 17 18 Battery voltage to launch engine by voltage 1 15 8 1 10 6 V 2 10 7 V 8 11 3 V 15 12 V 19 Engine runtime to charge the battery 1 6 3 1 10 min 3 30 min 6 60 min Gearbox type te Automatic 2 Manual Detected automatically Set 20 Gearbox Gearbox ype 1 2 aeaa ee o manually if required 21 Remote start feature l 2 1 start feature 2 1 enabled 2 disabled 1 disabled 2 1 0 s 3 3 0 s 4 5 0 s 5 ignoring 22 Ont poe tlhe aad all doors from receiving the command to engine launch Y and for 5 s after ignition was switched off _ 1 by CAN and impulse 0 4 s 2 impulse 0 4 s 3 23 Imitate drivers door switch af
4. Heater management protocol 2 Eberspacher 3 not preset automatic Heater shutdown conditions Heater operation time me Engine temperature level 1 time only 2 engine temperature only 3 time and temperature One unit equals 10 minutes 10 to 120 minutes 6 to turn off the heater gt 50 C 1 0 C 7 70 C Battery power level to _ _ 7 turn off the heater 9 11 3 V 1 10 5 V 11 11 5 V 8 Accept Decline operation of a 1 on factory heater via CAN bus 2 off Code to switch heater on with factory buttons You can program a code to switch on or off heater with factory buttons Programming is done the same way as PIN code Code can be entered only when the is ignition on 10 Heater control with the factory remote l off 11 Control of an aftermarket 1 2 1 1 status control heater algorithm 2 impulse control Programming sequence 1 Turn the ignition on 6 Adjust option settings by pressing the Programming button 2 Follow through with identity verification sequence the number of times matching the number of steps from the 3 Press the Programming button 17 times the Alarm will emit 8 current status to the required one The Alarm will confirm the audio and light signals selected function by audio and visual signals Please remember 4 Select menu option by pressing and releasing the Programming that from the last function the program will go to
5. Put the battery back into one of the RFID tags The Alarm will register this RFID tag while emitting audio signal After registration is complete the Alarm will emit series of audio and light signals indicating a number of all registered RFID tags Make sure that the number of signals equals the number of registered RFIDs If while registering an error occurs the Alarm will emit a warning signal and go back to indicating registered RFID tags Put the battery back into the next RFID tag wait until registration is completed Repeat the same steps for other RFID tags After the last RFID is registered release the brake pedal and turn the ignition off A trill will sound Check RFID link quality This check is performed when the vehicle engine is started While performing this check it is recommended to smoothly increase and decrease the engine rpm 1 Ai J ae i al a ey Follow through with identity verification Press the Programming button 12 times the Alarm will emit 4 audio and light signals Press the Programming button 15 times the Alarm will emit repeated series of 15 audio and light signals 4 Press and hold the brake pedal for 10 seconds until you hear oF an audio signal Release the brake pedal The Alarm will enable constant RFID tag search mode Check the quality of RFID detection by moving it around the vehicle Good reception is confirmed by a trill every 3 seconds To exit this option Check RFI
6. 10 Factory buttons Emitting a constant level signal when pressing a preset button of the vehicle 11 Ignition Emitting a constant level signal when the ignition is turned on including the engine startup Emitting a constant level signal when ACCs of the vehicle 1st key position for some vehicles it matches the 12 ACC ignition position are on The signal stops only after the key is out of the ignition lock This function can help to correctly manage power supply to an accessory alarm system of multimedia system 13 Engine is running Emitting a constant level signal when the engine is on Emitting an pulse with a pulse frequency in proportion with the engine crankshaft rom 1 pulse per second 14 Engine RPM corresponds with 20 rpm of the crankshaft The signal helps to evaluate the rpm rather than give an exact value Emitting a constant level signal if transmission handle is in preset position P R N D1 For semi automatic transmission positions R N D 1 for manual transmission only position R Emitting a constant level signal if the speed exceeds some threshold value the speed value is different for each vehicle but generally it is in the range of 5 to 10 km h 17 Front parking sensors control Emitting a constant signal level in accordance with the preset algorithm of the parking system 18 Rear parking sensors control Emitting a constant signal level in accordance with the preset algorithm of the parking system 19 Movemenken
7. Configuration of the Alarm hardware settings Configuration of ERS inputs outputs 11 6 Configuration of programmable inputs outputs Menu 1 1 C T configuration 12 4 Configuration of the user settings Set up shock sensors and tilt g 5 Adjustment of sensitivity of additional shock sensor switching on off movement sensor the tilt displacement sensor Menu is active only with ESM module installed or with remote start Remote start configuration 16 digital output active Heater configuration 17 8 Configuration of heater operating modes Programming the Alarm hardware The Alarm is programmed in accordance with Hardware features configuration table Table 7 Hardware features configuration Factory default settings Notes Option Range 1 Vehicle model _ 1 coats et a ee sah Mente i 2 control of a normally closed relay 2 Engine lock 1 4 2 3 acceletator pedal lock force to stop 4 starter motor lock 1 Engine will be locked regardless of speed 3 Safe lock 1 3 1 2 if speed is 30km h or lower 3 on complete stop _ 1 analogue buttons 2 digital buttons j Type of external buttons ve Inputs 7 and 16 connector X1 18 pin Control of the factory T 1 on gt security system 1 2 On 2 off 6 Sequential door opening 1 2 Off 7 off 1 pulse negative 2 status negative 7 Hazard lights control algorithm 1 5 3 pulse positive 4
8. Storage temperature C 40 85 Maximum relative air humidity 95 22 __ nT EC 61231 22 Technical Manuale PRIZRAK WWW PRIZRAK RU ed Co CN ELECTRONICS Comfort of modern technology Endorse if you like it
9. a control button they will not be activated when gearbox is in R position up to the next ignition or command from a control button Table 8 Configuration of programmable configuration of inputs outputs Connector Function Setting range d Bh ee ee 1 x1 AE a 1 41 Alternate hazard lights control Hazard lights alternate control 2 2 pin Polarity of output 15 1 2 Negative polarity 3 nen 1 41 17 ener output 7 5 O 8 pin port 1 41 25 alter Central Lock 8 pin output 8 6 8 pin port 1 41 4 alter Central Lock 7 ts UUS 1 24 12 8 Sea 1 24 7 o as o a Gogi i I femess e ara i Options 1 3 6 Designed to customize the Alarm outputs by assigning a function to a specific output see Programmable output functions table Option 2 Defines the polarity of the Alarm output 17 The polarity can be defined only if this output is assigned one of the functions see Programmable output functions Option 5 Arming pulse or lock Central Lock lock unlock Central Lock Option 6 Identity verification pulse or unlock Central Lock Options 7 12 To be able to program this pin Digital buttons option has to be chosen Options 7 14 Designed to customize the Alarm inputs by assigning a function to a specific input see Programmable input functions table 13 O Table 9 Functions of programmable outputs Function Description 1 Security state Emitting a cons
10. atennancnideatenacteatatstindaitaucasinanadeevaiees 10 Programming Stage ONG wassinircerencsihiudsaniansevercamansivatinesnascnaiimnnnddinates 10 Interfacing the Alarm with the Vehicle ccscccseessecsseeseeeseeseeesaees 10 Programming Stage CWO srciladmatisniaisnnianomiasrruanieiientsionmadinentuaiiann 10 Programming the Alarm configuration sesessesersersrsrnsnrrrerrrrererrnnenenne 10 Table 8 Programming MEenU ssssssssrssrssrsrrrrrnrrnnrsrrnnrnrrnrrnrrerenrrnrennnn 10 Programming the Alarm hardware cccscsscssecseeceeseseeseeeeeeeseeseeeeeeass 11 Table 9 The Alarm hardware configuration cssccseesssesseeseeesseeees 11 Table 10 Programmable configuration of inputs outputs c00 12 Table 11 Programmable output functions of the Alarm ccsccsseseeees 13 Table 12 Programmable input functions of the Alarm ccceeceeeeeeee 14 Configuration of integrated Sensors ccsccsccsecsecseeesetseeeeeeeeeaeeeeeeeees 15 Table 13 Configuration Of SHOCK SENSOF csecseeseeeseeseeeeeeeeeeeseeeeerees 15 Heater configuration sycs Gnd seinen nsecBaqencedusudsnectaca cad aitenrecusincdccianeuctecesess 15 Table 14 Heater configuration sic cedaitscctansncsmerdswsanceceiieancenneitoentehecnerceus 15 Programming the Alarm user settings ccsccseecseceeeeesseeeeesaeeaeeeeeeess 16 Table 15 Configuration of the Alarm user SettingS ccccsscesseeseeeees 16 Registration of ne
11. feature Immobilizer is a feature designed to prevent vehicle from being stolen from parking space PINtoDrive goes into effect if ignition was switched off for more than 3 seconds If PINtoDrive feature is enabled and active it requires PIN code to be deactivated otherwise engine will be locked e Engine will be switched off on attempt to move if speed control is enabled and supported by the vehicle e The engine will be turned off within 5 seconds after the ignition has been turned on if the Speed control is disabled or not supported by the vehicle AntiHiJack feature AntiHiJack is the function that prevents the vehicle from being hijacked or stolen from the parking area AntiHiJack enters the Guard mode in the following cases e The ignition was turned off for longer than 3 seconds including a case when Immobilizer is off if the Immobilizer was switched on the Alarm will follow its algorithms e The driver s door was opened Upon entering the Guard mode AntiHiJack feature goes through a series of phases and in case if the Guard mode was not deactivated the feature will activate the engine lock Phases change only when the ignition is on When the ignition has been turned off the Alarm saves the current condition and will continue the feature operation when the ignition is back on The Guard mode of the AntiHiJack feature can be deactivated at any step by entering the PIN code The Guard mode phases are as follows e I
12. long intermittent sound then two more signals after a pause Now all sensors are deactivated Trunk opening without leaving the security mode You can open the trunk with remote or keyless system While trunkis open alarm will stop reacting to sensor input but will control doors so the vehicle will stay secured from intrusion After trunk is closed the system will secure it and turn all sensors back on Hands free function When the engine was started remotely hands free function will check that the RFID tag is within the coverage The Alarm will automatically unlock the vehicle upon owners approach and will lock it back when owner left the vehicle RFID check when disarming In this mode when you unlock the vehicle via remote control or keyless access system the Alarm will search for the RFID tag Only after the RFID tag is detected the vehicle will be disarmed The RFID tag is looked for only if the Alarm was armed for more than 30 seconds While searching the system will emit intermittent sound If you don t have the RFID tag with you then within 10 seconds after a door hood or trunk is opened an alarm will go off To deactivate the alarm signal turn on the ignition and authenticate yourself Factory remote door lock control This function does not allow opening doors by using signal imitation equipment and also will lock access into vehicle in case if the remote was stolen if electromechanical locks were installed After
13. the first one button the number of times matching the number of option 7 The Alarm will exit the settings mode and save all configuration The Alarm will confirm the option number by a series of audio settings in energy independent memory when the ignition is and light signals turned off while brake pedal is released or within 10 seconds 5 Go to option setting by pressing and holding the brake pedal after last menu action if the brake pedal is released The Alarm will notify of the option status by a series of audio and light signals of a changing duration Remote start configuration Table 13 Engine remote start configuration Factory 0 N Function Range default Note 1 Hands free in remote start mode 1 2 2 1 enabled 2 disabled 2 ESM 250 configuration 1 16 Detected automatically Set up manually if required 3 Keep running feature 1 2 2 1 enabled 2 disabled 4 Keep running feature operation time 1 10 min 12 120 min 5 Turbotimer feature 1 enabled 2 disabled 6 External temperature sensor 1 temperature sensor 2 interior temperature sensor 1 brake pedal will be ignored 2 pressed brake 7 Ignore brake on engine start pedal will prevent the engine from launching Shut down engine by releasing brake pedal _ Bhs in remote start 1 2 2 1 enabled 2 disabled Brake state in CAN 1 2 2 1 enabled 2 disabled 10 Turn off the engine of disarming 1 enabled
14. D link quality press the brake pedal or exit programming mode by turning the ignition off Changing the PIN code Turn the ignition on Enter PIN code wait for confirmation Press the Programming button 14 times Wait for confirmation of the Alarm by 1 audio and 1 light signals Set the new PIN code by using any combination of buttons Pressing is confirmed by the audio and light signals Wait for confirmation by 1 audio and 1 light signal Re enter the new PIN code Wait for confirmation 2 audio and light signals and a trill mean that the PIN code has been changed and the Alarm has left the PIN code changing mode Sound alert means that the PIN code has not been changed a mistake has been made when entering the new PIN code and it is necessary to repeat the procedure of changing the PIN code starting from step 4 You can exit the PIN code changing mode anytime by turning the ignition off Reassigning the Programming button Reset all settings to factory defaults Interface the Alarm with the vehicle If analog steering wheel buttons are used please define them see above for the description of this procedure In order to assign any of the buttons perceived by the Alarm as the Programming button press the selected button and hold it for longer than 5 seconds until a long audio signal will be heard 5 The Programming button can be assigned within 15 minutes after interfacing the Alarm with the vehicle 19
15. N bus is not available This situation may occur when some circuits of the vehicle are blocked In this case the Ignition control input is to be connected to the vehicle wire that has a constant level signal when the ignition is on Connecting this input does not cancel the ignition analysis via CAN bus The ignition is considered on when data is received by any informational channel CAN bus or analog input Trunk state control The function is used in case an alarm is triggered when the trunk is opened via original remote control and or keyless access system In this case Trunk opening control input is to be connected to trunk opening feed control wire Input control is available only in Security mode When a command to open the trunk is detected the Alarm ignores external sensor inputs and trunk terminal switch for 5 seconds until the actual opening of the trunk In 5 seconds after the trunk lid has been closed sensor inputs and the trunk will be secured Parking system button The function controls parking sensors by using accessory button this may be required if there are no buttons in the vehicle detected by CAN bus Heater state When signal is fed to this input it means that external preheater is on Assigning this function to any digital output is a prerequisite for accessing the GSM module menu and preheater control 10 11 Wipers control Ignore brake pedal in remote start with alternative remote start module
16. TECHNICAL MANUAL press TA p lt l GS Comfort and innovation no remote controls Car Alarm System Si For modern day vehicles and drivers Table of Contents Description of the Alarm system cccccsccsseesseceeceecseeeseesesseeeaeessaesaeess 2 SEO CNIG TION sauidcaniacotcenmeennenoseueausianysectaeiiaceacededaisndeaeeaisianaeeaesausnceadeaneas 2 EUV Seat eee EEE A E E a E EEEE EEE A 2 Control by mobile phone s sssssssssssrnsnrsrrnrrnrrnrrsrrnrrnrrnnrnrrnrnnrrnrenrennnnnne 3 Structure of the smart voice MENU cccsccsseeseeeeeeceeesaeeeeesoeesseesaeeees 3 The Alarm operation algorithms cccsccssceseesseesseeseeesseseeeeseeeseesoeees 4 Table 1 Trigger diagnostics ssssssssesrnnrrsrrnrrsrrnrrsrnnrrnnnnnnnrennrnrennena 4 Factory remote door lock control s sssssssssrssrsnrsrrnrrnrnnrrsrrnrrnnrnrrnrennenne 4 Immobilizer featUre sssessssensrsrnsrrrrrrrrrerrnrsrrnrnrnnnnnnnnnrnnnnrennnrnnnnnnnnnnnnn 5 AntiHiJack feat re sssrinin aoaaa AAE R a En 5 RFID tag are E 5 Dual verification sesesserensrrrrrrsrrrrsrsrrernrrnrnrrnnnnnnnnnrnrennnrnnnnnnnnnnnnnnnnn 6 Table 2 Methods of verification ssssssssssrnnrnsrrnrrnrnrrrnrnnnnnrennenrennene 6 Quick engaging of the second circuit for higher risk locationS ssssssssssrnssrsrrerrnrrnnrnrrnrrnrrnrrnrrennnnrnrenrrnrennena 6 PIN COGS minen a E E e 6 PIN code entering Sequence ss ssrssrrrrsrrrrrsrr
17. cam activation D All handle positions used for forward movement of the vehicle D S M L etc If the heater was launched by the system the LEDs will stay on for heater operation Signal is formed if ignition is on for 5 minutes after alarm was triggered warning or alert if alert was triggered by phone If alarm was triggered again while dashcam is active dashcam will work for 5 more minutes Table 10 Programmable input functions Designation Description of the function 1 2 Brake lights state Hood state Door state Central Lock is closed status Central Lock is open status Ignition This function is used only if the vehicle CAN bus does not contain data on brake pedal position In this case brake light control input is to be connected with brake pedal terminal switch output This function is used if the vehicle CAN bus does not contain data on hood position In this case hood control is to be connected with hood terminal switch This function is used in exceptional cases when CAN bus does not contain data on door position please see the Integrator files This function is used in exceptional cases when CAN bus does not contain data on Central Lock status please see the Integrator files This function is used in exceptional cases when CAN bus does not contain data on Central Lock status please see the Integrator files The function is used only in cases when the correct data from CA
18. dle phase e Warning phase e Locking phase Idle phase In this phase AntiHiJack follows two different algorithms depending on the availability of Speed control If the Speed control is available AntiHiJack waits until the vehicle covers a set distance from the moment of Guard mode activation Upon that AntiHiJack goes into the Warning phase If the Speed control is not available Idle phase consists of three stages e Waiting for the driver s door to be closed e Waiting for preset amount of brake presses to be made e Pause before going to warning phase Warning phase consists of two steps e Warning the driver with the trill that they have to enter PIN code e Warning other drivers on the road of the possible hazardous situation due to the upcoming engine locking 10 seconds It is carried out by vehicle hazard lights Driver warning is still on Locking phase The engine lock is activated the siren is turned on and the hazard lights are activated The siren and hazard lights will switch off in 15 seconds AntiHiJack will be in locking phase until a new PIN code verification If Safe stop is enabled engine will be locked only if speed is lower then 30 km h or on complete stop depends on the settings of the safe stop The safe locking option reduces probablity of accidents when the Engine Lock feature is used When the ignition is off AntiHiJack turns off the hazard lights and audio warning signals for the driver If t
19. e Wait for the confirming trill e Enter PIN code Available PIN options Buttons 6 9 Q are used here as an example Request the list of avaliable buttons in your vehicle at your shop One digit PIN Two digit PIN j 2 second pause Single button PIN entry When entering the PIN code keep in mind the entering sequence One digit PIN Two digit PIN gt pP p Q 6 2 second pause PUK code PUK code is required if After PUK code is entered all security functions of the Alarm will e You have lost the RFID tag or lost forgot the PIN code be deactivated regardless the selected authentication method PUK e You want to change identity verification method code can be found under the scratch layer on the plastic card Oo The factory set PIN code is 2 it is entered by using the Programming button please check the Integrator PUK code entry PUK code is entered by the Programming button with a 2 second pause in between keystrokes Entering sequence e Enter PUK code e Turn on the ignition or start the engine e Wait for the confirming trill Maintenance mode Maintenance is an operation mode when all hijack protection and To activate or deactivate the Maintenance mode follow these service functions of the Alarm are temporarily disabled steps The Alarm will notify of activation of the Maintenance mode as 1 Turn off the ignition follows 2 Follow through with identity verification e W
20. e White Programmable input Disable alert if trunk is open 1 5 3 Yellow microphone Microphone 4 Black microphone Microphone 5 Yellow White Programmable output Front parking sensors control 150 8 pin 6 Green White Programmable output Rear parking sensors control 150 Impulse to close the hood Alternate Central 7 Green Programmable output Lock control Lock for twin wire control Lock 150 Unlock for one wire central lock control Authentication pulse Alternate Central Lock 8 Blue Programmable output control Unlock for twin wire Central Lock 150 control 1 Red White Power supply ier V power supply for Fortin or iDatalink uni 2 Black Yellow Power supply Ground for Fortin or iDatalink unit 3 Gray Blue DATA RX connect to the Control of a Fortin or iDatalink unit 4 pin blue wire Fortin or black white iDatalink wire 4 Gray Green DATA TX connect to the Control of a Fortin or iDatalink unit white wire Fortin or black white iDatalink wire 2 pin LED 1 Red output 12 V power supply Blue output Ground Given is the average current value in operating and idle modes It is subject to change according to positive outputs demand Useful current of output 9 depends on demand connected to negative outputs Outputs 6 15 and 17 are protected from short circuit inductive eruptions overheating and overload Description of pins in the Alarm main port Pins 1 10 11 Used only for additi
21. e battery type for the RFID tag is CR 2025 To replace it contact the system installer or do it yourself Carefully observe the polarity Open here eatcaciesi 8 TEn To easily open the tag you can use an edge of a plastic card Use only high quality non expired batteries a If the ambient temperature is below zero batteries can perform worse due to slower rate of chemical reaction It can make identification of the RFID tag more difficult especially if it was exposed to low temperature environment for a long time To restore performance of the battery just warm up the RFID tag Dual authentication Authentication locates and identifies the RFID tag and or entered PIN code This procedure is carried out when the ignition is on or the engine is started After successful verification LED will be switched off and a trill is emitted Table 2 Methods of authentication Method of authentication Verification procedure RFID tag factory default RFID tag is with you PIN code Enter PIN code Wait for a trill RFID tag is with you LED will go out RFID tag or PIN code oe RFID tag is not available Enter PIN code RFID tag and PIN code ni j n IN LED will go out O If you use the RFID tag and PIN code authentication both security circuits have to be deactivated before the vehicle starts moving If one or more circuits are still active i e there is no RFID tag or PIN code is not entered the vehicle wi
22. e button for 2 to 5 7 2 With the brake pedal pressed go to option 8 The Alarm will seconds Status control hold the button for at least 5 emit 2 successive series of 8 audio signals and then will seconds Release the button and the Alarm will emit one emit irregular audio signals After hearing the latter release audio and light signal and stop the displaying Release the the brake pedal The Alarm will continue to emit irregular brake pedal and the Alarm goes back to displaying the signals Open those doors which are to be indicated by option number this output Other doors should be kept closed doors can 11 In order to move to programming next menu option press be opened in advance Press the brake pedal again The Alarm will inform of the status by series of 8 signals and the doors will be assigned to this output If you do not press the brake pedal and abort programming the Alarm will save previous settings Release the brake pedal and the Alarm goes back to displaying the option number and release the Programming button for the number of times necessary for navigation from the required option for example in order to navigate from option 2 to option 8 press and release the Programming button 6 times Please note that when navigating menu options the first option follows the last one 8 Programming algorithm for function 10 Factory buttons With the brake pedal pressed go to option 10 The Alarm will emit 2 successive
23. ecd Emitting a pulse with a pulse frequency in proportion with the vehicle s speed 1 pulse per second corresponds p to 1 km h The signal helps to evaluate the speed rather than give an exact value 20 Brake Emitting a constant level signal when the brake pedal is pressed 21 Hand brake Emitting a constant level signal when the vehicle is on hand brake 22 External lights Emitting a constant level signal when external lights are on 15 Gearbox state 16 Vehicle is moving 23 Timer channel Comfort Timer control channel 10 to 60 seconds Control of a nobirmally closed locking relay which is cut into the vehicle diagnostics bus This function is enabled in Security mode and active CAN bus Emitting of 0 8 sec pulse after activation of Security mode provided that the hood is closed terminal switch is OFF or not assigned This function indicates the parking system status If parking sensors are operated by reverse gear algorithm 26 Parking system LED or by reverse gear with an override algorithm LED is on when sensors are on If parking sensors follow activated by speed level algorithm the LED is on while sensors are disabled This function has to be assigned to any digital output It is a prerequisite to access GSM module menu and gain control of the preheater 24 Diagnostic bus lock 25 Hood is closed pulse 27 External heater control Pulse to imitate closing of 28 driv
24. es door for ramole start Emitting of 1 5 sec pulse simulating the driver leaving the vehicle to switch ACC off Emitting of 0 8 sec pulse 29 Trunk is open This function has to be assigned to any digital output It is a prerequisite to access GSM module menu and gain control of the trunk Used only with aftermarket remote start module Emitting a constant level signal to remote start the engine 30 Control of an aftermarket on engine lauch until engine stop Signal will be shaped with or without the ESM 250 unit or ingition lock or remote start module start stop button connection Function has to be assigned to digital output afterwards the remote start menu and commands to control launches in the voice menu will be enabled 31 Accelerator pedal lock Stops the vehicle if AntiHiJAck was triggered according to the safe lock settings Controls a normally open force to stop relay Close electromechanical E 32 door locks Emitting a 0 8 sec pulse to close electromechanical door locks 33 Open electromechanical Emitting a 0 8 sec pulse to open electromechanical door locks door locks Control of a normally open aai 34 relay to control central lock Used to control circuits that control central lock Function is used to control a remote start module made by Fortin Tied with Dual wire control of a Fortin module Start function Attention Assigning this function to a programmable input will disable ESM 250 and functions 37 38 39 To Dual wire co
25. he Immobilizer feature has not entered the Guard mode see the Immobilizer feature section then upon the next ignition AntiHiJack will do an audio warning for the driver and switch on hazard lights for 15 seconds AntiHiJack will not prevent the ignition but will interfere with driving as per the same algorithms as the Immobilizer feature If Immobilizer is in the Guard mode then when the ignition switched off AntiHiJack will be deactivated and the Alarm will follow algorithms of the Immobilizer feature Accelerator pedal lock force to stop Feature will stop the vehicle if AntiHiJack was triggered minding Safe lock settings Vehicle has to support speed control At the eng of the warning phase if speed of the vehicel didn t increase within 5 seconds or brake pedal was pressed within 3 seconds lock will activate for 2 seconds then it will be lifted for 5 seconds This will be repeated 5 times Every repetition lock lift will be reduced for 1 second On fifth repetition lock will be permanent O RFID tag RFID tag is an electronic key that must be with the driver at all times during the vehicle operation Before the vehicle starts moving the system will automatically identify the RFID tag and deactivate all security functions When the RFID tag is identified the system will emit a trill Battery replacement If the battery needs to be replaced the system will trigger 5 short audio signals after the RFID tag is identified Th
26. he following tables Contact numbers are shown in Fig 1 Configuration of inputs outputs is programmed see Programming the Alarm hardware features 2 18 10 8 54 3 Lee ee 0000 OQ ee ee ee 0000 Oog 1 9 1 4 2 i Fig 1 Numbers of port connector pins from wiring viewpoint Table 4 Description of the systems main 18 pin connector Connector Color Type Note Current mA 1 Ground Power for additional devices TP BUS 2 Blue Yellow Heater WBUS Webasto Ebersacher 3 Brown CAN 2 CAN2 L bus 4 Brown CAN 1 CAN1 L bus 5 Pink Green programmable input Stop signal control 1 5 6 White Black output Wired engine lock 150 7 Gray Black programmable input Reference ground Negative button 0 5 8 Yellow Red Data link Connection between main unit and lock relay 18 pin 9 Black Ground Power 10 12 V Power for additional devices TP BUS 11 TP BUS control bus for additional devices 12 Brown Yellow CAN 2 CAN2 H bus 13 Brown Red CAN 1 CAN1 H bus 14 Green Black programmable input Hood position control 1 5 15 Blue Red programmable output Turn signals alternate control 150 16 Gray Yellow programmable input Analog buttons Positive button 0 5 17 Pink Black output Siren control Horn control 1 300 150 18 Red 12 V Power supply 1 500 10 1 Orange Green Programmable input Engine shutdown in remote start 15 2 Orang
27. hen disarming LED will turn on 3 Press the Programming button 6 times you should start within e When the ignition is turned on LED will go out 10 seconds after verification e After identity verification an alarm will sound 4 Wait for confirmation of your actions e After the ignition is turned off LED will light up and will be on e If the Maintenance mode is on the system will emit 1 for a while audio signal 1 light signal and a trill e If the Maintenance mode is off the system will emit 2 audio signals 2 light signals and a trill Automatic deactivation of the Maintenance mode This function automatically disables the Maintenance mode after If the vehicle does not support Speed control automatic a 10 km run So even if you forget to disable this mode in the service deactivation of this feature will not be avaliable Station it will still be automatically disabled If Maintenance mode is activated by PUK code it cannot be automatically disabled O Warning signals after authentication Additional sound signals after verification usually call for certain actions Table 3 Warning signals after authentication Warning signal Source of a signal Actions to take The default PIN code was not changed Change the default PIN code Long audio The maintenance mode is on Disable the Maintenance mode signal When installing the system verification method Enter PIN code was switched to RFID tag or PIN code ll P that verificat
28. icate the number of option by series of audio and light signals 5 To program the selected option press and hold the brake pedal The Alarm will notify of the option status by a series of audio and light signals of a changing duration The Alarm will leave programming mode and save all settings when the ignition is turned off while brake pedal is released or within 10 seconds after last menu action if the brake pedal is released For efficient and convenient built in shock sensor test it is possible to temporarily exit the configuration mode To do this press and hold the brake pedal and turn off the ignition while configuring any of the zones When the ignition is off no trill sound will be made Check the sensor in operational mode When you temporarily exit the configuration mode windows are not closed automatically otherwise the Alarm is operated in standard mode When the ignition is on the system automatically goes back to the point in configuration process before the exit If you do not go back to configuration mode within 10 minutes by turning on the ignition the Alarm system will save the previously set sensitivity of the sensor and exit automatically You will hear a trill 16 Heater config uration Table 12 Heater configuration Factory Function pate default Description g settings 1 Accept Decline operation of 1 on an aftermarket heater 2 off 2 Heater operation in preheating mode i 7 off 1 Webasto
29. ill not be detected 2 110 km h 4 130 km h 10 190 km h 14 Register new RFID tags 2 Range 0 to 6 15 Check RFID link quality 18 1 2 Programming sequence Turn the ignition on Enter PIN code wait for confirmation If the vehicle has passed 10 km after installation and the factory set PIN code remained unchanged it is allowed to use PIN code 2 for identity verification by pressing an integrated button To enter the Alarm configuration menu press the Programming button 12 times do it not later than 10 seconds after entering the PIN code If your actions are correct the Alarm will confirm it by 4 audio and light signals Select menu option by pressing and releasing the Programming button the number of times matching the number of option The Alarm will confirm the option number by a series of audio and light signals 5 Go to option setting by pressing and holding the brake pedal The Alarm will notify of the option status by a series of audio signals of a changing duration Adjust option settings by pressing the Programming button the number of times matching the number of steps from the current status to the required one Please remember that from the last function the program will go to the first one Release brake pedal Now you can move to programming the next function or exit the programming mode Go to configuring another option by pressing the Programming button the number of times matching the
30. ion method was Five short audio signals Battery in the RFID tag should be replaced Replace RFID tag battery Other options The system has several options to make your vehicle more comfortable and secure Geolocation of the vehicle Central lock control The system can show the vehicle position on the map at any moment It If your vehicle does not have an integrated door lock activated when requires installation of a GPS GLONASS 270 unit To locate the vehicle you driving locking or turning off the ignition unlocking this option can need to send a text message command or via voice menu or using your be provided by the Alarm system mobile application Microphone Automatic window roll up A microphone provided with the Alarm system enables the driver The system can be programmed so that the vehicle windows are at any point to hear sounds inside the vehicle or in the vicinity This rolled up when engaging the lock requires only one call to the Alarm system Setting the electromechanical hood lock Optional parking system control You can install an additional hood lock and program the Alarm to The Alarm system has flexible algorithms to control additional parking lock the hood when locking the vehicle and open it only after identity sensors There are three control modes available and the system can verification be controlled by using original buttons in the vehicle Inputs outputs of the Alarm Inputs outputs of the Alarm are described in t
31. ll not move O Authentication method can be selected when installing the Alarm without using the PUK code As a result the PUK code remains secret Authentication method can be changed without using the PUK code if e The vehicle did not travel more than 10 km after the Alarm was installed the Speed control is available e The ignition was not active for more than 20 minutes after the Alarm was installed the Speed control is not available If during the installation the verification method was switched to RFID tag or PIN code after the vehicle was driven for 10 kilometers if the Speed control is unavailable after the ignition was on for 20 minutes at the end of each verification an alarm signal will sound It will inform that verification method was changed To deactivate the signal enter the PIN code Quick engaging of the second circuit for high risk locations The RFID tag authentication is very easy to use In most cases this To quickly engage maximum security verification method is enough to protect the vehicle However when e Turn on the ignition leaving the vehicle in high risk locations for example at public parking e Wait for RFID identification lots you can provide maximum hijack protection by engaging second circuit for one security cycle Authentification method can be quickly In the next 10 seconds changed from RFID tag or PIN code to RFID tag and PIN code Open and then close the driver s door without need to use
32. ll notify you with 4 audio and light signals According to Menu 2 select option 3 Distance for enabling AntiHiJack by pressing the Programming button 3 times The Alarm will inform you about chosen menu option number by a series of 3 audio and light signals Enter option 2 by pressing and holding the brake pedal The Alarm will show option setting by a repeated double audio and light signals because the current factory set option setting 1 100 meters Change option 3 to do so press brogramming button 2 times i e increase setting by 2 1 2 3 The Alarm will inform you about chosen menu setting with by a series of 3 audio and light signals 300 meters Exit programming mode by turning the ignition off Reset to the factory default settings The Alarm has a procedure of resetting the programmable settings when all settings of the vehicle model are removed from the Alarm permanent memory and PIN code and all other programming options are returned to factory set values 6 FA 8 9 10 IL LZ To reset to the factory default settings if the Alarm is installed Disconnect power supply from the Alarm Press and hold the built in button See Connection scheme Connect the power supply while holding the button The Alarm will emit dashed audio signal Release the button and wait until the dashed signal stops Turn on the ignition Enter PIN code a trill will be made A signal will notify you that the Alarm wa
33. ls turned off while brake pedal is released or within 10 seconds 5 Go to option setting by pressing and holding the brake pedal after last menu action if the brake pedal is released The Alarm will notify of the option status by a series of audio and light signals of a changing duration Programming user functions configuration Table 14 Configuration of the Alarm user functions Current option setting Seay re Off Description p default LED Number of LED Number of settings audio signals audio signals 1 Immobilizer PINtoDrive feature On 1 Off 2 2 AntiHiJack feature On Off 2 5 Distance for enabling AntiHiJack 1 Range 1 to 10 aoe from 1 to 4 1 siren is aap siren one be i te tet enabled on warning 3 warning signal volume equals arming 4 Siren operation when alarm is triggered 4 disarming volume refer to function 11 4 siren is enabled Maximum volume Audio notification that RFID tag is being looked for gt after disarming On On J off 2 Audio confirmation of authentication by RFID tag and 6 or PIN code On On 1 off 2 7 Automatic deactivation of maintanence mode On On il Off 2 8 Close central lock while driving Off On 1 Off 2 9 Open central lock if ignition is off Off On 1 off 2 10 Automatically close windows when ignition switched off On On 1 Off 2 11 Volume of arm disarm notifications 4 Range 1 to 4 12 Authentication PUK code is required to change 1 Range 1to3 Range 1 to 10 13 Speed threshold 4 1 Speeding w
34. mended to check sensitivity settings and adjust them if required e If same circuit that is used for connection with the alarm is locked Communication and power has to be connected higher than lock point CAN bus parameters indication Geature shown following parameters Hood trunk doors each door individually Ignition switch state key presence ACC IGN Start Engine is running Gearbox state for automatic P R N D for manual R Parking brake Stop signal Security Factory security system alert Central lock state Sensors ignore Engine RPM Engine temperature 10 Feature allow quickly check vehicle state and adjust connection if required Buit ib LED is used for indication check Connection scheme LED lights up if any parameter is selected and stays for 5 seconds or until other parameter is chosen Engine RPM and Engine temperature will be indicated if no other parameters are chosen Engine RPM LED flashes with frequency proportional to the RPM 1 flash per second equals 500 RPM of the engine Engine temperature LED flashes 1 time every time new data received with ignition or or the engine running Programming Stage one The Alarm is programmed by using the Programming button Identifying the vehicle model Vehicles supported by the system are divided into groups each of which is divided into subgroups All groups and subgroups are assigned with a number see the In
35. mmunication testing but the Alarm will function only with a pLine 221 relay tied with a specific main unit Accelerometer sensitivity adjustment Turn the ignition on Enter PIN code wait for confirmation Press and release the Programming button 10 times this has to be done within 10 seconds after entering the PIN code The Alarm will confirm menu entry with three audio signals 6 Choose Menu 1 option 20 by pressing and releasing the Programming button 20 times The Alarm will notify of this option by a sequence of 20 audio signals 4 Depress brake pedal and hold it for more than 10 seconds The alarm will indicate current sensitivity settings factory default 1 maximum sensitivity iy 5 Start the engine and check sensitivity in the range within idle 2000 RPM If lock triggers immediately after accelerometer press reduce sensitivity by pressing button 1 time Start the engine at lest 3 times to be sure that lock will not happen o After starting the engine let it run for at least 10 seconds To leave the programming mode turn off the ignition and wait for at least 3 seconds 11 O Programming Stage two Programming the Alarm configuration At stage two the Alarm hardware functions and user settings are changed and a new PIN code is programmed Table 6 Programming menu Number of Name of the menu Menu code audio signals Designation Hardware features 10 3 configuration Menu 1
36. nction then press again the brake pedal The Alarm will stop emitting 2 Arming pulse to function 16 Vehicle is moving press irregular signals and go back to displaying the option status by the Programming button 14 times The Alarm will confirm the series of 15 signals Release the brake pedal and the Alarm selected function by audio and visual signals Please remember goes back to displaying the menu option number If you do not that from the last function the program will go to the first press the brake pedal and abort programming of this option one Release brake pedal to switch indication from status to the Alarm will save previous settings the number of current menu option Now you can move to 10 Programming algorithm for assigning a parking control button programming the next function or exit the programming mode With the brake pedal pressed go to option 14 Menu 1 The 7 Programming algorithm for function 8 Doors hood and Alarm will start emitting irregular audio and light signals trunk Press and hold the selected button for a certain amount of 7 1 Set any combination of doors hood and trunk which when time if the Alarm recognizes the button the system will stop opening will emit a signal at a programmable output In emitting signals while the button is pressed this description doors hood and trunk are referred to as Short button press hold the button for at least 2 seconds doors Long button press 2 5 sec hold th
37. nd AntiHiJack features Speed control can be activated and de activated in user settings programming menu Certain vehicles may not support this feature please see Integrator files for details Guard mode active state of the PINtoDrive and AntiHiJack if one of these functions has entered guard mode to leave it it is required to enter PIN code otherwise engine will be locked Comfort feature feature allowing not only to lock doors from the factory remote but also to raise windows sunroof also can be closed O Control via mobile phone It is possible to control the Alarm via mobile phone for example arm Control via text messages and disarm the Alarm schedule tasks start the heater etc It is possible to control your Alarm via text messages Options of the phone control include the smart voice menu Russian P A and English languages are avaliable please contact your shop to Access code CommandN Parameter change the language of the system or application TEC you may Access code a code to access the system download it from application store on your device and text messaging CommandN number of a command in the voice menu Parameter it is used as an option for some commands Please see Getting started details at www canbus alarm com To start using the phone application you need to dial the phone For example 1111 822 this is a command to disarm the alarm in number of the Alarm and follow voice p
38. nd power 12 V 1 A 10 mA Black Power source Ground Yellow Common contact Lock output 10 A Yellow Red Normally closed contact Lock output 10 A Yellow Black Yellow White Normally open contact Lock output 10 A While transmitting data pulses up to 1 A When receiving data up to 10 mA Limited by cross section of the wire Communication and power has to be connected to the positive switched circuit of the vehicle This circuit has to be enabled if the Ignition is enabled for example ignition injectors ignition coils You may lock any circuit in the vehicle After installation it is recommecned to check link between relay and Alarm Relay has a built in accelerometer for vehicles that have no information about speed in the CANbus and enables extra features for vehicles that have information about speed present in the CANbus e Lock the engine even if there is no speed information in the CAN bus O e You may install only one pLine 221 relay in the vehicle e Relay works as normally locked relay e Accelerometer allows starting the engine and locking it if the vehicle began movement It is not recommended to install the relay in places that vibrate heavily during engine starting or launching This can prevent movement detecton due to excessive noise passed to accelerometer Factory default sensitivity settings mean that there are almost no vibrations transfered from the engine After installing the alarm it is recom
39. ntrol of a 35 Fortin module Ground while running reenable ESM 250 and disabled features reprogram this function Function is used to control unit made by Fortin Tied with Dual wire control of a Fortin module Ground 36 Dual wire control of a while running Fortin module Start Attention Assigning this function to a programmable input will disable ESM 250 and functions 37 38 39 To reenable ESM 250 and disabled features reprogram this function 14 Function Description 37 38 Start Stop button control remote start 39 Brake pedal press remote start 40 Immobilizer bypass module remote start Single wire iDataLink module control Function to enable remote launch on vehicles equipped with start stop button without remote start module Output operates exactly as corresponding output of ESM 250 Function to enable remote launch on vehicles equipped with start stop button without remote start module Output operates exactly as corresponding output of ESM 250 Function to enable remote launch on vehicles equipped with start stop button without remote start module Output operates exactly as corresponding output of ESM 250 Function is used to control unit made by iDataLink Attention Assigning this function to a programmable input will disable ESM 250 and functions 37 38 39 To reenable ESM 250 and disabled features reprogram this function 41 LED to show heater state 42 Dash
40. number of steps from the current status to the required one For example to go from option 2 AntiHiJack feature to option 8 Activation of Central Lock while driving press the Programming button 6 times You can exit programming mode at any moment by turning off the ignition If no actions were taken within 60 seconds and brake pedal was released the Alarm will exit programming mode A trill will sound Registration of new RFID tags All RFID tags for the Alarm system should be registered all together RFID tags that were not registered with others will be removed from the memory of the Alarm system Registration sequence Choose one RFID tag which will be used for identity verification Remove batteries of all others If you use PIN or PUK verification remove batteries from all of the RFID tags Follow through with identity verification If the vehicle was driven for 10 km after installation and the factory set PIN code remained unchanged it is allowed to use PIN code 2 for identity verification by pressing a built in button Press the Programming button 12 times the Alarm will emit 4 audio and light signals Press the Programming button 14 times the Alarm will emit repeated series of 14 audio and light signals 5 8 Press and hold the brake pedal The Alarm will identify the number of registered RFID tags by series of audio and light signals Number of signals per series is a number of registered RFID tags
41. ock in high risk locations 12 22 Fuel tank volume 1 30 1 Used to convert fuel level from percent to liters 1 not defined Fuel is measured in percent 2 10 liters 30 150 liters Step is five liters 1 disabled 2 0 5s 3 1 0 s 4 2 0s 5 3 0s 1 enabled 2 disabled If feature is enabled and supported by the vehicle check Integrator engine can be locked via CAN bus without additional connections Alert delay if perimeter i 23 was breached Is 1 24 Engine lock via CAN 1 2 2 25 Perimeter control pause 30s 1 2 2 27 Immobilizer bypass unit 1 2 1 on 2 off Set automatically 1 Fortin 2 iDatalink Option 13 Parking system operation algorithm e Activation by reverse gear Front and rear parking sensors are switched on when gearbox is in R position or by using a control button They are switched off when the speed exceeds 15 km h or by using the parking system control button e Activation by speed Front parking sensors are switched on if the vehicle speed is under 15 km h Rear parking sensors are switched on if the vehicle moves backwards with a speed under 15 km h In this mode all parking sensors can be disabled by using a control button until the next ignition sequence or command from a control button e Activation by reverse gear with a shutdown override Here algorithm is similar to Activation by reverse gear However when parking sensors are disabled by using
42. oee eee eee eeeeeeeeveeaoeoeoeoeoeoeoeneeeoeeeeeoeoeeeeeeee eee eeoeeee ee eo e eeeeeeeeeeeeeveeoeeeveeee eee eeeeeeaevneoeeeeoeeeeeeoeoeee eeeeeeeeseeeoeeoeeoeseeeeeeeeeoeeoeeeeeeeeeeaeeeoeaeeee eee e ee eeeeeeeeeeaeeeeeeeeeeeeeeveeeaoeaeeeeeeaevoeeeoeaee ee ee eeeeeeeaeoeoeoeeeoeeeeeeeeoeeeeeeeaoeeeeeoeeeneeeeee eee 8 eeeeeeeaeaeaeseoeoeaeeeoeoeeeeoeseeaoeoeeeoeoeeeoeoeoeeeaeeoeeee eee eeeeeeecaeaoeoeeoeaeaeeaeeoeoeeeoeoeeoeoeeeoeaeeaeneoeaeeaeeeoee ee eee 8 eo eeeeeeeeoeevoeeoeoeoeeoeoeoeseeoeeoeeeoeeoea ooo eeoeoeeeeoe ee ede eeeeeaeeeaeveoeocoeoeeoeeeeoeoeoeoeoeoeoeoeoeeoseeeaoeeeeoeeoeoe eee ee 8 eo eeeceeeeeeoeeeeoeeoeeeeoeseeoeeoeeoevoeeoeeaeoeeeoeoeeeeeeeo ee e eeeeoeeaeseoevneeoeeeoeeeeeeeoeoeeoeoeeoeaeeeoeeneeaoeeeoeee eee 8 e e eeeeeevseeoevoeeaoeeoeseeoeeeeeoeeseevoeeeaevseeneeoeeeeeoeeoeesde eeeeeeeeoeeoecoeoeeoeoeeeoeeeeeeeeeeeeeeeeeeeeaeaeaeeoe ee Oo Keep this sketch out of the reach of third parties TEC 61231 22 Technical Manuale PRIZRAK icture to draw arrangement 21 Standard delivery package Central unit RFID Tag A set of wiring harness Siren CD Reminder card User manual Warranty certificate Connection diagram Unit package ee Ore Specifications and operating conditions Power supply voltage V oa L5 Maximum current draw in standby mode mA 10 Maximum current draw in operating mode A 1 9 Operating temperature C 40 85
43. on has been accessed the system will indicate it audibly if the communication has been established short two tone signals each 0 5 second no communication steady two tone signal Operation of all main systems of the vehicle should be tested in all available modes ideally the system operation should be checked with various combinations of electric equipment e Turn the on climate control in various modes e Changing the speed of the heater fan Shee e Changing the operating modes of heating systems Seat heater in different power modes window and mirror heating e Changing the operating modes of lighting low beam marker lights fog lights Special attention should be paid to communication testing for high engine rpm The engine speed should be changed very smoothly while constantly monitoring the system Communication errors can occur in a very narrow range of the engine rpm OIsolated communication errors occasional short term jams indicated by variable two tone signals are allowed If under any condition communication errors are frequent dual tone signal is on for longer than 2 seconds choose another connection circuit since tested connection does not guarantee a fail safe operation of the system To exit this Menu item tap the brake pedal To exit the programming mode turn the ignition off 0 Any pLine 221 relay even priviously installed on another vehicle with a different main unit can be used for co
44. onal optional modules connected via TP BUS such as HCU 230 hood module ESM 250 remotestart module etc Pin 2 Heater control Webasto Eberspacher Pins 3 12 CAN2 vehicle data bus Connected in particular cases please see the Integrator files Pins 4 13 CAN L CAN H vehicle data buses Connected to the vehicle CAN bus please see the Integrator files Pin 5 Brake lights state Used if the vehicle CAN bus does not contain brake pedal position data please see the Integrator files In such cases Pin 5 is connected to the output of brake pedal terminal switch Pin 6 Engine lock Connected to one of the relay coil contacts which is used to lock or startup the engine Pin 7 Reference ground Negative button Subject to selected type of a control button one of the following functions is used e Reference ground when an analog control button is selected pin is connected to the appropriate wire of the vehicle please see the Integrator files e Negative button is connected to the negative controlled by making contact with the ground button It is used when there are no original buttons recognized by the Alarm If the vehicle has original buttons operated via CAN bus and recognized by the Alarm this input can be vacant Pin 8 Data Connects to positive terminal of switched or non switched circuit 12 V signal has to be present when the engine is running This connection is used to connect lock relay and the main
45. receiving a signal to open from the factory remote the alarm will search for RFID tag and only after authentication doors will open Feature can operate permanently RFID tag will be required every disarming of the alarm and temporary in places where you need maximum safety see Quick engaging of the second circuit for higher risk locations Toggling and selection of the operational mode is done in the alarm hardware features menu There are three methods to use this feature Each method can be used on its own or together with other methods Installing electromechanical door locks Electromechanical locks are controlled with Close electromechanical door locks and Open electromechanical door locks outputs Pulse to close locks will be formed after arming the alarm condition being doors trunk and hood are closed Pulse to open after receiving signal from factory remote and RFID authentication Oo If the vehicle is opened by phone RFID tag is not required CAN bus lock No additional connections required For support of a specific vehicle check Integrator Commutation of central lock control circuits with output Control of central lock normally open relay Signal is formed on the output after receiving signal from factory remote and RFID authentication and stays until alarm is armed Signal is constantly present if CAN bus is active if maintenance mode is active or PIN Code authentication was chosen Immobilizer
46. rm press unlock button of the remote or open vehicle with keyless system Alarm will warn you with 2 audible signals LED will go off Arming and disarming can be done by the voice menu or the mobile application Warning about open door If you left an open door hood or trunk and armed the Alarm the system will warn you with 3 audible signals LED will inform you about Open compartment e Two the hood is open e Three the trunk is open e Four the door is open O The Alarm cannot monitor entry through unlocked door It is possible to close the doors hood trunk while still in Security mode then the Alarm will automatically continue monitoring Triggering the Alarm The alarm has 2 built in sensors shock sensor and tilt movement sensor Because of these sensors the alarm is able to differentiate different influences on the vehicle Optional sensor can be connected if required The alarm can be connected to multiplex sensors and standard sensors In secure state alarm can react to external action by warning or by triggering Warning will be made if small force was applied to the shock sensor In this case alarm will make short audio signals Alarm will be triggered if any door hood or trunk is open if tilt movement sensor is triggered and if excessive force was applied to the shock sensor Siren will be on for 30 seconds and hazard lights will blink dp You can adjust sensors sensitivity Function of protecting p
47. rompts this example the access code is the factory code 1111 After the Alarm is installed 1 Assign your mobile phone as User 1 2 Change the factory access code Oo Default access code is 1111 Structure of the smart voice menu EEE C ame System Information Online Data Unit 7 2 Information about vehicle state Trigger log Event log G List of deactivated features and functions 7 6 Task manager contents Help Quickly provides online critical information about the state of the Alarm and the vehicle The unit contents can be changed i Control Commands 8 2 Commands to control the Alarm 8B Activation and extra channels 8 4 Checking account balance etc Quick Access Commands 8 Help 2 3 4 6 Bale These commands can be customized ts settings 9 2 Task manager DLB Remote launches and optional channels 7 System Information DA Sensors 8 Control Commands 238 Online data unit 9 6 Quick access commands 2 Settings DA Users and access permissions D8 Notification settings Help D Advanced settings Hel General information about the system j Alarm operation algorithms Arming disarming To arm the alarm press the lock button of the remote or close the doors with keyless system or lock the door with the key Alarm will warn you that it is armed with audible signal and LED flashes After some time interval between flashes will decrease To disarm the ala
48. rrrnrrsnrnrrsrrnrrnrenrrnrennenne 6 PUK COUE esn a e E ys ewdaeemnaeaneaeecenemanrae meee 7 Maintenance MOS scicannninsisanetacrsanasnsenneieianiarsnieicsasennnaliammanteindieneapaes 7 Automatic deactivation of Maintenance Mode ss sssssrrssrsrrsrrsrrerrnne 7 Warning signals after identity Verification ccccccscsseeeeeeseeeeeeeaeeseeeeaes 7 Table 3 Warning signals after identity Verification ccccscsseeseeeeeeeees 7 Other Options creision ener er eer gm pe ene sates ete nae ene tr ee a ne eat anon enter 7 COMIC TION tadintet etude acteurs n a a a aeania 7 Inputs outputs of the Alarm s sssssssssnsrrsrrsrrnrrnrrnrrnrrnrrnnrnnnnnennrnrennenne 7 Table 4 Description of the Alarm main 18 pin Connector esssesnn 8 Table 5 Description of the Alarm 8 pin port programmable inputs outputs and alternate Central Lock control c sccsseeeseeseeeseeseeeceesoeesseesseeses 8 Table 6 Description of the Alarm 4 pin port additional Sensor cccscssecceseeeeeceeccneceneecnssenscsnesneesess 9 Table 7 Description of the LED poOrt ssssssssrrsresrssrrsrnnrrsrnnrnsrnnnenrenrnna 9 Table 8 Description of relay OUtDUTS ccseecsseseesseeseeeeseeaneeseeseeees 9 The Alarm connection diagram factory SettingS ccccssecsseeseeeseeeaees 9 Displaying of CAN bus parameters cceccecsseeseecsecseeeeeeeeceeseeteeeeeeeeeeas 9 Programming the Alarm mewsiveniaatetnareatantsreecn ante
49. s reset to factory default settings Disconnect the power source and CAN bus from the alarm If the Alarm was not installed in the vehicle There are 3 ways to reset the alarm 20 k 2 With built in button if factory PIN code 2 was not changed and vehicle was driven for less then 10 kilometers With built in button and PIN code d By installing the Alarm in the same vehicle as it was installed before if you know the PIN code Sequence for the first two ways 1 2 a 4 Press and hold the built in button Connect the power supply while holding the button The Alarm will emit dashed audio signal Release the button and wait until the dashed signal stops If the vehicle was not driven for more then 10 kilometers enter PIN code 2 with built in button Otherwise enter PUK code with the built in button A trill will be made A signal will notify you that the Alarm was reset to factory default settings Disconnect the power source Only owner of the system should scratch PUK code and enter it Figure 2 Arranging the Alarm units in the vehicle Use the p e of the Alarm units This can help to find the alarm units eeeeeeeeaeoeeceoeeeeaeoeeaeeoeoeeeaoeeeoeoeoeoeoeeoeeneeoeeo eee ee eeeeeseeeceaoeaeoeoeoaeeaeoeooeeaoe eee eaoeaoeeoeeeaoeeeooeoeoeeaeneoe eee eee 8 eeeeeeeeeoeooeooeoeeoeoeeeoeeceoeeeaoeeeeoseeeoeeeeoeoeoeoeoeoeaoe ee eo eeeeeeeseeeeeeoeeeoeeeeseeeaoeeeeeeeoseeeaoeeeee
50. series of 10 audio signals and then will emit irregular signals While still holding the brake pedal press the required button please refer to Integrator for the list of buttons for each vehicle If the Alarm recognized the Exiting the programming mode The Alarm will exit programming mode and save all configuration settings in energy independent memory when the ignition is turned off or within 60 seconds after last menu action if the brake pedal is released Configuration of integrated sensors Table 11 Configuration of shock sensors and tilt movement sensor Function Range Factory default Notes 1 Shock sensor warning perimeter 0 8 4 x F ai e e i 2 Shock sensor trigger perimeter 0 8 4 E Seea ae l 0 perimeter switched off 3 Tilt Movement sensor 0 8 4 8 maximum sensitivity Programming sequence 1 Turn on the ignition 6 Adjust option settings by pressing the Programming button 2 Enter PIN code wait for confirmation the number of times matching the number of steps from the 3 Press and release the Programming button 8 times The Alarm current status to the required one The Alarm will confirm the will emit five audio and light signals selected function by audio and visual signals From the Last 4 Choose required option by pressing and releasing the function the program will cycle to the first one Programming button a number of times matching a number of option The Alarm will ind
51. status positive 5 lights control negative 1 single wire pulse negative 2 single wire pulse negative if central lock state if unavaliable 3 two wire pulse negative Selecting operating mode and polarity of output 17 1 Siren control Emitting of a constant level signal 12V 2 Horn control Emitting of an intermittent negative signal Controls the original horn of the vehicle g Central lock alternative 1 3 control algorithm 9 Siren control Horn control 1 2 1 Time interval of Timer 10 Channel Comfort feature 1 6 3 One unit equals 10 seconds g 1 multiplex operating mode of external sensors 1 External sensors multiplex mode 1 2 1 2 standard operating mode of external sensors 1 on 12 Engine start lock 1 2 2 gt off 1 Parking system control 1 3 1 1 by reverse gear 2 by speed algorithm activation 3 by reverse gear with an override _ T It is possible to assign CAN bus recognized button 14 Parking system control button analog button or digital button positive negative J 15 Speed control 1 2 1 E off 16 Brake presses 1 7 3 R 1 on GSM interlock disabled 17 GSM lock 1 2 2 2 off GSM interlock enabled 18 Car battery warning threshold 1 15 8 11 3 1 10 6 V 15 12 V 19 20 1 RFID tag 1 4 1 1 not in use 2 RFID check when disarming 3 factory remote lock 4 factory remote l
52. stem has been powered If all actions were performed correctly the Alarm will make three audio signals 3 Enter Menu option 1 Vehicle model by pressing the Programming button once The Alarm will notify of the selection of this option by repeating single audio signal 4 Enter the vehicle group number by pressing the Programming button corresponding number of times See the Integrator 5 Enter the vehicle subgroup number by pressing the Programming button a relevant number of times please see the Integrator files O If the group number is a two digit number enter the first digit wait for 2 seconds and then enter the second digit The Alarm system will emit a sequence of audio signals indicating the group number By listening to audio signals verify that the vehicle model was selected correctly e If the model was selected correctly press the Programming button once Signal sequence will stop and the vehicle model will be saved e If the vehicle was identified incorrectly press the Programming button twice Repeat programming starting from step 4 Analog steering wheel buttons programming To program analog steering wheel buttons 1 Right after the Alarm identifies the model turn the ignition on and wait for at least 5 seconds 2 Press all the steering wheel and steering wheel column joysticks buttons cruise control central unit control etc sequentially one after another Sound after button press means that this b
53. tant level signal while the Alarm is in Security mode 2 Arming pulse Emitting 0 8 sec pulse when entering the Security mode or triggering AntiHiJack feature 3 Disarming pulse Emitting 0 8 sec pulse when leaving the Security mode Emitting 0 8 sec pulse after PIN code is entered or in Maintenance mode 1 second after the ignition has 4 Authentication pulse been turned on 5 6 Factory alarm panic Emitting of a constant level signal while the original alarm system if installed is in alarm condition Beaver nanie Emitting a 30 sec constant level signal in Security mode if one of the main zones doors hood trunk is PEP triggered or any sensor is triggered The signal stops after exiting the Security mode Emitting a 30 sec pulse signal in Security mode if one of the main zones doors hood trunk is triggered Signal is also emitted when arming disarming This function can be used for the vehicles without any integrated original alarm system The signal stops when exiting the Security mode This function can send an alarm signal to original horn of the vehicle 7 Horn panic 8 Doors hood and trunk Emitting a constant level signal if any of the preset doors hood or trunk is triggered Emitting a constant level signal in the Security mode if the trunk is opened via original remote control The 9 Sensor ignore signal is also emitted for the purposes of Comfort feature This function can disable sensors to prevent false alarms
54. tegrator Identification is the procedure of detecting group and subgroup of the vehicle by the system There are two ways to identify the vehicle 1 Automatic identification After connecting with the vehicle CAN bus supplying power and performing a few simple actions for most vehicles those are the ignition on off and close open the cenral lock via original remote control group and subgroup will be detected automatically The user verifies identified group and subgroup by listening to the sound signals group number pause subgroup number pause Identification procedure for all supported vehicles can be found in the Integrator 0 If the group number is a two digit number each digit will be identified individually For example group 35 and subgroup 2 will produce the following sequence of sound signals 3 long signals pause 1 sec 5 long signals pause 2 sec 2 short signals pause 4 sec etc 2 Forced interfacing This is used in extraordinary cases Programming is carried out with the integrated button Before interfacing the vehicle group must not be identified and the CAN bus must not be connected The Alarm will leave the programming mode if the Programming button is not pressed for longer than 60 seconds Programming sequence 1 Power the Alarm wait for an intermittent sound 2 Enter Menu 1 press and release the Programming button 10 times this has to be done within 10 seconds after the sy
55. ter Menu 1 press the Programming button 10 times the the brake pedal and the Alarm goes back to displaying the Alarm will emit three audio and three LED signals To enter menu option number If you release the brake pedal before Menu 1 2 press the Programming button 11 times the Alarm assigning a button the Alarm will exit this option save will emit six audio and light signals previous option settings and go back to indication of the 4 Select menu option by pressing and releasing the Programming option number button the number of times matching the number of option 9 Programming algorithm for function 15 Gearbox state The Alarm will confirm the option number by a series of audio With the brake pedal pressed go to option 15 The Alarm will Signals emit 2 successive series of 15 audio signals and then will emit 5 Go to option setting by pressing and holding the brake pedal irregular audio signals While still holding the brake pedal The Alarm will notify of the option status by a series of audio switch the transmission to required position P N D or R signals of a changing duration transmission selector can be set in the necessary position in 6 Adjust option settings by pressing the Programming button the advance For automated transmission switch to R N D and number of times matching the number of steps from the current for manual transmission you can only switch to R Release status to the required one for example to go from fu
56. ter remote start L impulse 1 0 s 4 impulse 1 5 s 5 impulse 3 5 s 24 Automatic central lock close after remote start 1 enabled 2 disabled 25 re rearming the alarm after remote start shut 1 enabled 2 disabled Time of preheating with the heater the engine before _ ER _ bx E 26 eoler 1 10 min 2 20 min 4 40 min Temperature of preheating with the heater the engine on TESTO on 27 E A EE E 1 10 C 2 5 C 3 0 C 10 50 C 28 Delay of the remote start after preheating 1 disabled 2 5 min 3 10 min 4 15 min 29 Remote start with the factory remote oft Programming sequence 1 Turn the ignition on 6 Adjust option settings by pressing the Programming button 2 Follow through with identity verification sequence the number of times matching the number of steps from the 3 Press the Programming button 16 times the Alarm will emit 7 current status to the required one The Alarm will confirm the audio and light signals selected function by audio and visual signals Please remember 4 Select menu option by pressing and releasing the Programming that from the last function the program will go to the first one button the number of times matching the number of option 7 The Alarm will exit the setting mode and save all configuration The Alarm will confirm the option number by a series of audio settings in energy independent memory when the ignition is and light signa
57. the settings menu Enter the PIN code wait for confirmation Turn off the ignition Wait for two trills which mean that RFID tag and PIN code verification method is activated O PIN code PIN code is a secret combination of presses on one or more PIN code can be easily changed many times by both technical original buttons in the vehicle Please refer to the Integrator files for the specialists during installation of the system or by user during day to list of original buttons that can be recognized by the system in a specific day use of the vehicle vehicle PIN code is entered before driving the vehicle To ensure a proper security level the factory default PIN code PIN code is a one two three or four digit number should be changed If you don t do it an alarm will sound after entering the PIN code which reminds you to change the PIN code The factory default PIN code is 2 it is entered by using the Programming button please see the Integrator Entering the PIN code PIN code is entered with the ignition or engine turned on by pressing original buttons When entering one of the PIN digits please make sure that pressing time or pause are no longer than 1 second Please keep a pause of approximately 2 seconds in between digits If you made a mistake while entering the PIN code a warning will sound in about 3 seconds then you can re enter the PIN code PIN code entry sequence e Turn on the ignition or start the engine
58. tify engine state only in turbo timer keep running or auto launch mode In other modes signal from this input is not used and engine state is taken from the CAN bus if it is available Input has a priority over Engine was started signal from CAN bus system responses only signals from this input Input can recognize continuous signals as well as pulse signals Signal to this input will launch factory or aftermarket heater Heater will run as long as the signal is present The function is used when CAN bus does not contain data on door position state please see the Integrator files Signal to this input allows to get information about alert state of the factory security system of the vehicle If signal is present Factory security system is in alert state Signal on this input will engage RFID tag search 1min and authentication After authentication alarm will disarm and central lock will open RFID tag will be looked for 1 minute or until alarm is armed whichever comes first Feature enabled if Menu 1 N921 RFID tag set to factory remote lock nnn factory remote lock in high risk locations in Menu 2 option N9212 Authentication set to any state except PIN code Used to set Beach mode 15 Programming sequence 1 Turn on the ignition button it will stop emitting irregular signals and go back 2 Enter PIN code wait for confirmation to indicating option status by series of 10 signals Release 3 To en
59. ublic order After three triggers in armed mode from one sensor in one hour alarm will stop responding to this sensor for one hour Alarm will continue working with this sensor if there were no triggers for one hour This function will cancel alerts but warnings will stay Trigger check Alarm remembers causes of alerts for security period Memory will be cleared after ignition switched on If alarm was triggered after disarming the alarm four audible signals will be made and indcation of cause will start check table 1 Table 1 Trigger indication LED flashes Note x1 Public order feature x2 Hood was opened x3 Trunk was opened x4 Door s was were opened x5 Triggering of the shock sensor alarm x6 Triggering of the shock sensor warning x7 Triggering of the tilt displacement sensor x8 Triggering of an extra sensor alarm x9 Triggering of an extra sensor warning aly Detailed information about events can be found in the trigger log which can be accessed from the voice menu Arming with sensor deactivation There are situations when you need to arm the Alarm with sensor input deactivation To deactivate sensors e Arm the alarm e Press the remote control button for 3 seconds The siren will emit one long intermittent sound then a short sound after a pause Now the warning is off The Alarm will not respond to mild impact to the vehicle e Within the next 3 seconds press the remote control button o again the siren will emit one
60. unit 0 Do not connect Data output to the cigarette lighter circuit Pin 9 Ground Connected to the vehicle body via connection point designated by the vehicle s manufacturer for ground connections with factory equipment Pin 14 Hood position state Used only when the vehicle CAN bus lacks information about hood position Pin 15 4 output Alternative hazard lights control Controls hazard lights for the vehicles where CAN bus is not used For more details on how to use it in a specific vehicle please refer to the Integrator Pin 16 Analog button Positive button Subject to selected type of a control button one of the following functions is used e Analog button is connected to the relevant wire of the vehicle at the steering wheel helix port please see the Integrator files e Positive button is connected to the positive button controlled by 12V voltage Used when original buttons are not recognized by the Alarm If there are available original CAN buttons and they are recognized by the Alarm this input can be left unused Pin 17 Siren control Horn control Appropriate algorithm is set when the Alarm is installed see Programming the Alarm hardware features Pin 18 Power supply of the Alarm Connected via 3A fuse to one of the non switched 12 V circuits pLine 221 description and installation guidelines Table 5 Relay outputs description Color Type Note Current Red Communication a
61. utton was recognized Turn the ignition off a trill will sound 4 Turn the ignition on 5 To assign the Programming button from available buttons push it and hold for at least 5 seconds until you hear an audio Signal Digital button programming To use digital button positive and or negative e Set the Alarm to operate with digital buttons Menu 1 Option 4 note that this menu option can be modified only by using a built in button and before the PIN code was entered for the first time via using analog or digital buttons Any further modifications will possible only after system reset e Assign activated button as the Programming button turn the ignition on push the button and hold it for at least 5 seconds until you hear an audio signal Button have to be programmed within 15 minutes after interfacing the Alarm If these 15 minutes have passed initiate the reset sequence and perform programming steps again Connection check between main unit and relay Turn the ignition on Enter PIN code wait for confirmation Press and release the Programming button 10 times this has to be done within 10 seconds after entering the PIN code The Alarm will confirm menu entry with three audio signals 4 Choose Menu 1 option 19 by pressing and releasing the Programming button 19 times The Alarm will notify of this option by a sequence of 19 audio signals 5 Push brake pedal and hold for at least 10 seconds After the Menu opti
62. w RFIDS escccusetnees cenesseecticvatennientsuatencisniendiecenecacetss 17 Quality check of RFID detection s sessssersrrerernerrrrnrrnrnrerrnrernnrenenrnnne 17 Changing the PIN COd 6 s escstececimauanesancsresnosieacacssscdehacmantansdetametieadeadga 17 Reassigning the Programming button s ssssserssrsrrsrrnrnnnnsnrrnrsrrenennee 18 Programming the Alarm by a computer sssssssssrsrrsnrsnrenrsrrnrrnrrnnrsnne 18 Resetting to factory default settings s sssserersersrrrrsnrrrsrrrrererrnnenenns 18 Arranging the Alarm units in the Vehicle ccccssecsseessesseeeeeeseeeees 19 Standard delivery package cccsecssceseecseesseeeseecceesseeceeesanesseeneeeseeesans 20 Specifications and operating conditions s s sessesersersrssrnrrnrnrerrnrerennnrens 20 Description of the security system Introduction Differences between security systems Prizrak 810 basic system Prizrak 830 RFID tag and second circuit of protection Functions of the Alarm e Protecting the vehicle from being stolen or hijacked e Alert if the vehicle was tampered with e Remote engine start optional may require ESM 250 remote start module e Heater control factory or aftermarket heater e Location tracking of the vehicle GPS GLONASS 270 unit is required The Alarm has an integrated GSM module to control security and the vehicle The system can be operated via mobile phone with a user friendly voice interface onl
63. y Russian and English languages icurrently available or via Android iOS application or text messages Identity of the user is verified by the RFID tag DDI technology and or PIN code entered by standard push buttons in the vehicle The alarm has motion tilt and shock sensors built in Optional sennsors can be connected via built in IO 2CAN technology makes it possible to work with two CAN buses simultaneously expanding the functions of the Alarm in some vehicles Integrator www tec integrator com contains information about compatibility of the Alarm with a specific vehicle and a list of vehicles compatible with the Alarm and specific features of the alarm Terms Programming button one of the factory default buttons with which the Alarm can be programmed buttons specific to the vehicle can be found in the Integrator Programmable button can be changed only within short time after installation of the Alarm Also built in button can be used as programming button Fig 2 Security is a state of the Alarm which is turned on after locking the doors in any way provided by the manufacturer of the vehicle keyless entry system remote control rearming the alarm etc and turning factory security system Secure state can be left by unlocking the doors with the original remote control or vehicles keyless access system or by entering the PIN code Speed control allows setting the locking activation algorithm for Immobilizer a

Comfort and innovation –

Contents

Download Pdf Manuals

Related Search

Related Contents

Comfort and innovation &ndash;

Contents

Download Pdf Manuals

Related Search

Related Contents

Comfort and innovation –